SKQGABE010

TACT SwitchTM 5.2×5.2mm Low-profile (SMD)Type SKQG Series Car Use RoHS applicable Two types, 0.8mm height without stem or 1.5mm height with stem. Detector ● Features 5.2×5.2mm dimension suitable for high density mounting. Much thinner and lighter than conventional products. Flat type with 0.8mm height in pursuit, for thin design. "With stem" type in pursuit for easier use. Contact sealed construction offers a highly reliable switch. Reflow solderable. Packaged with a 12mm wide embossed taping. Push Slide Rotary Encoders Power Dual-in-line Package Type Multi Control Devices TACT SwitchTM CustomProducts ● ● ● ● ● Applications ● For operating various electronic devices such as audio devices, video recorders, communication devices, cameras, automotive sets, electnic home appliances, etc. Products Line Products No. SKQGAEE010 SKQGAAE010 Operating Operating Travel Rating Rating Operating life Initial contact direction （mm） （max.） （min.） （5mA 5V DC） resistance force 0.98N 500,000 cycles 1.57N 2.55N 0.98N 1.57N With stem 2 2.55N 100,000 cycles 3.43N Vertical 0.25 50mA 12V DC 10BA 1V DC 50,000 cycles 100mΩ max. Without stem 1 Variety Drawing No. Sharp Feeling Soft Feeling Snap-in Type Surface Mount Type Radial Type SKQGACE010 SKQGAFE010 SKQGABE010 SKQGADE010 SKQGAKE010 500,000 cycles For other specifications, see P.369 For soldering conditions, see P.370 For specifications for the taping package, see P.372 336 TACT SwitchTM 5.2×5.2mm Low-profile (SMD)Type SKQG Series Dimensions No. Photo Without stem type 1 2 Unit:mm Style PC board mounting hole dimensions （Viewed from switch mounting face） Detector Push 3.7 5.2 ø3 Prohibitted area of copper tracks 0.5 Slide Rotary 2.6 1 3 5.2 6.4 4 4.8 Encoders 2 4.4 Power Dual-in-line Package Type Multi Control Devices With stem type 1 2 0.8 8 TACT SwitchTM CustomProducts 0.5 3.7 5.2 ø2 Prohibitted area of copper tracks 2.6 2 3 5.2 6.4 4 4.8 2 Sharp Feeling Soft Feeling Snap-in Type Surface Mount Type Radial Type Stem 4.4 8 Circuit Diagram 1 3 2 4 0.8 1.2 1.5 337 TACT Switch TM Products Specifications Series Sharp feeling type Items ｰ20℃ to ＋70℃ SKHJ/HL/QJ/RR/RV/QC/QK ｰ30℃ to ＋85℃ ｰ20℃ to ＋70℃ SKEG ｰ40℃ to ＋90℃ Soft feeling type Operating temperature range Detector Push Slide Rotary Encoders Power Dual-in-line Package Type Multi Control Devices TACT SwitchTM CustomProducts Insulation resistance Electrical performance Voltage proof Vibration Durability Lifetime Cold Environmental performance Dry heat Damp heat 100MΩmin. 100V DC SKEY/PD : 50MΩmin. 100V DC 250V AC for 1 min. SKRE/SKSC/SKRB/RV/RH/RM/RW/RR/EY/PD : 100V AC for 1min. 10 to 55 to 10Hz/min., the amplitude is 1.5mm for all the frequencies, in the 3 direction of X, Y and Z for 2 hours respectively Shall be in accordance with individual specifications. ｰ30±2℃ for 96h 80±2℃ for 96h 60±2℃, 90 to 95%RH for 96h Note We can raise the working temperature range for in-vehicle applications upon request. Contact us if you have any requirements of this kind. Specifications of LED SKHJ） （ Power Forward pulse Forward dissipation peak current current P mW） （ Red 2.7 max. 2.05TYP Pure green Amber Orange （High brightness） Green （High brightness） 40 80 15 2.7 max. 2.0 TYP 3 4 2.7 max. 2.05TYP 10 max. 630 TYP 565 TYP 40 TYP 30 TYP 1.5min. 4.0 TYP 2.0min. 5.0 TYP 4 555 TYP 590 TYP 20 TYP 30 TYP Color of light Reverse voltage Forward voltage VF V） （ IF=10mA Reverse current IFP mA） （ IFDC mA） VR V） （ （ Peak emission wave length IR μA） λpeak nm） （ （ VR=4V IF=10mA 5 max. 700 TYP Spectral line half width Δλ nm） （ IF=10mA 100 TYP Luminous intensity IV mcd） （ IF=10mA 0.4min. 1.0 TYP 0.8min. 2.0 TYP 0.4min. 1.0 TYP Sharp Feeling Soft Feeling Snap-in Type Surface Mount Type Radial Type 369 TACT Switch TM Soldering Conditions Condition for Reflow Available for Surface Mount Type.（Except SKRM, SKRR Series） 1. Heating method: Double heating method with infrared heater. 2. Temperature measurement: Thermocouple 0.1 to 0.2φ CA K） CC T） soldering portion copper foil surface） A heat resisting tape （ or （ at （ . Detector Push Slide Rotary Encoders Power should be used for fixed measurement. 3. Temperature profile Temperature (˚C ) 260˚C max. 3 sec max. 180 150 Time 230˚C Dual-in-line Package Type Multi Control Devices TACT SwitchTM CustomProducts 120 sec max. pre-heating ） （ 3 to 4min. Time inside soldering equipment Note 40s max. 1. The condition mentioned above is the temperature on the mounting surface of a PC board. There are cases where the PC board's temperature greatly differs from that of the switch, depending on the PC board's material, size, thickness, etc. The above-stated conditions shall also apply to switch surface temperatures. 2. Soldering conditions differ depending on reflow soldering machines. You are requested to verify the soldering conditions thoroughly beforehand. Sharp Feeling Soft Feeling Snap-in Type Surface Mount Type Radial Type Conditions for Auto-dip Available for Snap-in Type and Radial Type （Except SKHJ, SKHL, SKQC, SKQJ, SKQK, SKEG series） Items Flux built-up Condition Mounting surface should not be coated with flax Ambient temperature of the soldered surface of PC board. 100℃ max. 60s max. 260℃ max. 5s max. 2times max. Manual Soldering (Except SKRT series) Items Soldering temperature Continuous soldering time capacity of soldering iron Condition 350℃max. 3s max. 60W max. Preheating temperature Preheating time Soldering temperature Continuous dipping time Number of soldering Notes 1. 2. 3. 4. 5. Consult with us for TACT SwitchTM washing conditions. Prevent flux penetration from the top side of the TACT SwitchTM. Switch terminals and a PC board should not be coated with flux prior to soldering. The second soldering should be done after the switch returns to normal temperature. Use the flux with a specific gravity of at least 0.81. （EC-19S-8 by TAMURA Corporation, or their equivalents.） 370 TACT Switch TM Specification of Embossed Taping Package Taping Packaging for Auto-insertion Reel Size Plastic Reel Detector Push Slide Rotary Encoders Power Dual-in-line Package Type Multi Control Devices TACT SwitchTM CustomProducts Applicable series SKQM, SKPM SKHM, SKHU, SKQY, SKRT, SKRAAK, SKRAAL SKQG SKRP SKRKAE, SKRKAH SKQR, SKRB SKRM, SKRW SKRE, SKRN, SKRKAG,SKSC Qty/reel pcs.） （ （Minimum packing unit） 2,000 3,000 Pull direction 1.75 Unit:mm Applicable series SKHM, SKHU, SKQG, SKQL, SKQM, SKQR, SKQY, SKRAAK, SKRAAL, SKRB, SKRE, SKRK, SKRM, SKRN, SKRP, SKRT, SKRW, SKPM,SKSC SKQT, SKRAAM, SKRAAQ, SKRH, SKRR, SKRV, SKPG, SKPN ø380 W W 13.5 17.5 33.5 SKQUBA, SKQUDB Unit:mm Tape dimensions 5,000 Without stem type） （ 4,000 With stem type） （ 4,000 2 4 4 ø1.5 hole (5.5) 4,500 10,000 8 5,000 2 4 4 1.75 (5.5) 12 ø1.5 hole Sharp Feeling Soft Feeling Snap-in Type Surface Mount Type Radial Type SKRH 1,300 2 ø1.5 hole 12 Pull direction R0.75 12 SKQL 3,000 12 4 1.75 7.5 Pull direction SKRV 1,500 SKRAAM, SKRAAQ SKQT SKRR SKPN 1,400 16 Pull direction 40 ø1.5 3,000 7,000 1,100 4 2 SKQUBA 750 14.2 28.4 32 0.2 SKQUDB 600 16 2 4 40 1.75 Note Consult with us for a φ330 mm diameter reel. 372 7.5 Pull direction 1.75 SKPG 1,200 2 ø1.5 hole ※12 4 ※Excluding SKQT i.e.8） （ 16