TM11264JCCWG

SPECIFICATION FOR LCD MODULE Model No. TM11264JCCWG Prepared by: Checked by : Verified by : Approved by: Date: Date: Date: Date: TIANMA MICROELECTRONICS CO., LTD Ver.1.0 REVISION RECORD Date Ref. Page Revision No. Revision Items Check & Approval 1/22 Ver.1.0 1 General Specifications: 1.1 Display type: STN 1.2 Display color*1: Display color: Blue-Black Background*2: White 1.3 Polarizer mode: Transflective/Positive 1.4 Viewing Angle: 6:00 1.5 Driving Method: 1/65 Duty 1/9 Bias 1.6 Lcd operation voltage: 9.5V VDD: 2.6~3.0V 1.7 Backlight: LED (Color: Blue&Amber) 1.8 Controller: S6B0724A01-B0CY 1.9 Data Transfer: 8 Bit Parallel(6800) or Serial 1.10 Operating Temperature: -20----+70℃ Storage Temperature: -30----+80℃ 1.11 Outline Dimensions: Refer to outline drawing on next page 1.12 Dot Matrix: 112X 64 DOTS 1.13 Dot Size: 0.22X0.25 (mm) 1.14 Dot Pitch: 0.24X0.27 (mm) 1.15 Weight: Approx 10g 1 * Color tone is slightly changed by temperature and driving voltage. *2 Color tone will be changed by backlight. 2/22 Ver.1.0 2 Outline Drawing 3/22 Ver.1.0 3 LCD Module Part Numbering System T M 11264 J C C W G G:COG MODULE W:WIDE TEMPERATURE RANGE POLARIZER MODE C: TRANSFLECTIVE, WITH LED BACKLIGHT LCD TYPE C: FSTN, POSITIVE MODULE SERIES MODULE TYPE 5 DIGITS INDICATING 112 COLUMNS X 64 ROWS T: TIANMA M: MODULE 4/22 Ver.1.0 4 Circuit Block Diagram 5/22 Ver.1.0 5 Absolute Maximum Ratings Item Power Supply Voltage LCD Driving Voltage Operating Temperature Range Storage Temperature Range Symbol VDD－VSS VLCD TOP Min. -0.3 -0.3 -20 Max. 7.0 V 17.0 +70 ℃ TST -30 +80 Unit Remark No Condensation 6/22 Ver.1.0 6.1 Electrical characteristics Item Symbol Supply Voltage (Logic) Supply Voltage (LCD Drive) High VDD－VSS Min. Typ. Max. Unit 2.6 3.0 3.5 V VLCD VIH （VDD=3.0） VIL （VDD=3.0） IDD (VDD－VSS=3.0) 4.5 9.5 15.0 V Input Signal Voltage 0.8VDD - VDD V Low 0 - 0.2 VDD V Supply current (Logic) (Display Character) - 30 300 uA Blue Supply current (LED Backlight) IBL (Vf=3.35v) 30 - mA Amber (Vf=1.9v) - mA 7/22 Ver.1.0 6.2 Interface Signals Pin No. Symbol 1 CS1B 2 RESETB 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 RS WRB RDB Level Description H/L Chip selects signal. “ L” Active H/L Reset Signal H/L H/L H/L H: Input data are display data L: Input data are control data R/W signal Enable signal Data bit 0 Data bit 1 Data bit 2 Data bit 3 Data bit 4 Data bit 5 Data bit 6 Data bit 7 Power supply voltage for logic and step-up voltage Ground DC/DC voltage converter output Capacitor pin for voltage converter Capacitor pin for voltage converter Capacitor pin for voltage converter Capacitor pin for voltage converter Capacitor pin for voltage converter Capacitor pin for voltage converter Power supply voltage for LCD Power supply voltage for LCD Power supply voltage for LCD Power supply voltage for LCD Power supply voltage for LCD Voltage adjustment pin Parallel/Serial Select Signal Internal Resistor Select Signal 8/22 Ver.1.0 D0 H/L D1 H/L D2 H/L D3 H/L D4 H/L D5 H/L D6(SCLK) H/L D7(SID) H/L 2.6~3. VDD 0V 0V VSS VOUT C4+ C3+ C1C1+ C2+ C2V1 V2 V3 V4 V0 VR PS H/L INTRS H/L 6.3 Interface Timing Chart RS tAS68 CS1B (CS2=1) tPW68(R), tPW68(W) E 0.1VDD 0.9VDD tDS68 DB0 to DB7 (Write) tACC68 DB0 to DB7 (Read) tOD68 tDH68 tAH68 tCY68 Read / Write Characteristics (6800-series Microprocessor) Item Address setup time Address hold time System cycle time Data setup time Data hold time Access time Output disable time Enable pulse Read width Write Signal RS RS DB7 to DB0 E_RDB Symbol tAS68 tAH68 tCY68 tDS68 tDH68 tACC68 tOD68 tPW68(R) tPW68(W) Min. 0 0 300 40 15 10 120 60 (VDD = 2.4 to 3.6V, Ta = -40 to +85°C) Typ. Max. Unit Remark 140 100 ns ns ns ns CL = 100 pF 9/22 Ver.1.0 tCSS CS1B (CS2 = 1) RS tCYS DB6 (SCLK) 0.9VDD 0.1VDD tWLS tDSS DB7 (SID) tASS tCHS tAHS tWHS tDHS Serial Interface Characteristics Item Serial clock cycle SCLK high pulse width SCLK low pulse width Address setup time Address hold time Data setup time Data hold time CS1B setup time CS1B hold time Signal DB6 (SCLK) RS DB7 (SID) CS1B Symbol tCYS tWHS tWLS tASS tAHS tDSS tDHS tCSS tCHS Min. 250 100 100 150 150 100 100 150 150 Typ. - (VDD = 2.4 to 3.6V, Ta = -40 to +85°C) Max. Unit Remark ns ns ns ns 10/22 Ver.1.0 6.4 Instruction Code Instruction Table ×: Don't care Instruction Display ON / OFF Initial display line Set page address Set column address MSB Set column address LSB Read status Write display data RS 0 0 0 0 0 0 1 RW 0 0 0 0 0 1 0 DB7 1 0 1 0 0 BUSY DB6 0 1 0 0 0 ADC DB5 1 ST5 1 0 0 ON/OFF DB4 0 ST4 1 1 0 RESETB DB3 1 ST3 P3 Y7 Y3 0 DB2 1 ST2 P2 Y6 Y2 0 DB1 1 ST1 P1 Y5 Y1 0 DB0 DON ST0 P0 Y4 Y0 0 Description Turn on/off LCD panel When DON = 0: display OFF When DON = 1: display ON Specify DDRAM line for COM0 Set page address Set column address MSB Set column address LSB Read the internal status Write data into DDRAM Write data Read display data 1 1 Read data Read data from DDRAM Select SEG output direction When ADC = 0: normal direction (SEG0→SEG131) When ADC = 1: reverse direction (SEG131→SEG0) Select normal / reverse display When REV = 0: normal display When REV = 1: reverse display Select normal/entire display ON When EON = 0: normal display. When EON = 1: entire display ON Select LCD bias Set modify-read mode release modify-read mode Initialize the internal functions Select COM output direction When SHL = 0: normal direction (COM0→COM63) When SHL = 1: reverse direction (COM63→COM0) Control power circuit operation Select internal resistance ratio of the regulator resistor Set reference voltage mode Set reference voltage register Set static indicator mode Set static indicator register Compound Instruction of display OFF and entire display ON ADC select 0 0 1 0 1 0 0 0 0 ADC Reverse display ON / OFF 0 0 1 0 1 0 0 1 1 REV Entire display ON / OFF LCD bias select Set modify-read Reset modify-read Reset 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 1 0 1 0 0 1 0 0 1 0 1 1 EON BIAS 0 0 0 SHL select 0 0 1 1 0 0 SHL × × × Power control Regulator resistor select Set reference voltage mode Set reference voltage register Set static indicator mode Set static indicator register Power save 0 0 0 0 0 0 - 0 0 0 0 0 0 - 0 0 1 × 1 × - 0 0 0 × 0 × - 1 1 0 SV5 1 × - 0 0 0 SV4 0 × - 1 0 0 SV3 1 × - VC R2 0 SV2 1 × - VR R1 0 SV1 0 S1 - VF R0 1 SV0 SM S0 - 11/22 Ver.1.0 7 Optical Characteristics 7.1 Optical Characteristics Item Symbol Condition Min. Typ. Ta=25℃ Max. Unit θ x Viewing Angle θ y Cr≥2 y θ=0° -30 -- 20 Deg θ=0° x θ=0° x θ=0° y -30 -- 30 Contrast Ratio Turn on Turn off Cr 3 - - Ton θ=0° x θ=0° y Toff - - 300 ms Response Time - - 300 12/22 Ver.1.0 7.2 Definition of Optical Characteristics 7.2.1 Definition of Viewing Angle Top Top Bottom 7.2.2 Definition of Contrast Ratio Bottom Contrast Ratio = B2/B1 = unselected state brightness selected state brightness Measuring Conditions: 1) Ambient Temperature: 25℃ 2) Frame frequency: 84.0Hz 7.2.3 Definition of Response time Turn on time: t o n = t d + t r Measuring Condition: 1) Operating Voltage: 9.5V Turn off time: t o f f = t d + t f 2) Frame frequency: 84.0Hz 13/22 Ver.1.0 8 Reliability 8.1 Content of Reliability Test No. Test Item 1 High Temperature Storage Low Temperature 2 Storage 3 Content of Test Endurance test applying the high storage temperature for a long time Endurance test applying the low storage temperature for a long time Endurance test applying the High Temperature electric stress (voltage ＆ current) Operation and the thermal stress to the element for a long time Endurance test applying the Low Temperature electric stress under low Operation temperature for a long time Endurance test applying the high High Temperature temperature and high humidity /Humidity Storage storage for a long time Endurance test applying the low and high temperature cycle Temperature -30℃←→25℃←→80℃←→25℃ Cycle 30min 5min 30min 5min ←────────────→ 1 cycle Vibration Test (package state) Shock Test (package state) Atmospheric Pressure Test Endurance test applying the vibration during transportation Endurance test applying the shock during transportation Endurance test applying the atmospheric pressure during transportation by air Ta=25℃ Test condition 80℃ 240H -30℃ 240H 70℃ 240H -20℃ 240H 60℃ 95%RH 240H -30℃/80℃ 10 cycles 10Hz~500Hz, 100m/s2, 120min Half- sine wave, 300m/s2, 18ms 25kPa 16H 4 5 6 7 8 9 14/22 Ver.1.0 8.2 Failure Judgment Criterion Criterion Item Basic Specification Electrical specification Mechanical Specification Optical Characteristic Note Remark √√√√√√ Test Item No. 123456789 Failure Judgement Criterion √ √ √ √ √ √ √ √ √ Out of the basic Specification Out of the electrical specification √√ Out of the mechanical specification √ Out of the optical specification √√√√√ For test item refer to 8.1 Basic specification = Optical specification + Mechanical specification 15/22 Ver.1.0 9 QUALITY LEVEL Examination At Tamb=25℃ or Test (unless otherwise stated) External Visual Inspection Inspection Min. Max. Unit IL AQL Major 1.0 II Minor 2.5 Major 1.0 Display II Minor Defects 2.5 Note: Major defects: Open segment or common, Short, Serious damages, Leakage Miner defects: Others Sampling standard conforms to GB2828 Under normal illumination and eyesight condition, the See annex A distance between eyes and LCD is 25cm. Under normal illumination and eyesight condition, See annex B display on inspection. 16/22 Ver.1.0 10 Precautions for Use of LCD Modules 10.1 Handling Precautions 10.1.1 The display panel is made of glass. Do not subject it to a mechanical shock by dropping it from a high place, etc. 10.1.2 If the display panel is damaged and the liquid crystal substance inside it leaks out, be sure not to get any in your mouth, if the substance comes into contact with your skin or clothes, promptly wash it off using soap and water. 10.1.3 Do not apply excessive force to the display surface or the adjoining areas since this may cause the color tone to vary. 10.1.4 The polarizer covering the display surface of the LCD module is soft and easily scratched. Handle this polarizer carefully. 10.1.5 If the display surface is contaminated, breathe on the surface and gently wipe it with a soft dry cloth. If still not completely clear, moisten cloth with one of the following solvents: — Isopropyl alcohol — Ethyl alcohol Solvents other than those mentioned above may damage the polarizer. Especially, do not use the following: — Water — Ketone — Aromatic solvents 10.1.6 Do not attempt to disassemble the LCD Module. 10.1.7 If the logic circuit power is off, do not apply the input signals. 10.1.8 To prevent destruction of the elements by static electricity, be careful to maintain an optimum work environment. a. Be sure to ground the body when handling the LCD Modules. b. Tools required for assembly, such as soldering irons, must be properly ground. c. To reduce the amount of static electricity generated, do not conduct assembly and other work under dry conditions. d. The LCD Module is coated with a film to protect the display surface. Be care when peeling off this protective film since static electricity may be generated. 17/22 Ver.1.0 10.2 Storage precautions 10.2.1 When storing the LCD modules, avoid exposure to direct sunlight or to the light of fluorescent lamps. 10.2.2 The LCD modules should be stored under the storage temperature range. If the LCD modules will be stored for a long time, the recommend condition is: Temperature : 0℃ ～ 40℃ Relatively humidity: ≤80% 10.2.3 The LCD modules should be stored in the room without acid, alkali and harmful gas. 10.3 The LCD modules should be no falling and violent shocking during transportation, and also should avoid excessive press, water, damp and sunshine. 18/22 Ver.1.0 Appendix A Inspection items and criteria for appearance defects Items Protective Glue Cover Tape Leakage Rainbow Wrong polarizer attachment Polarizer Bubble between polarizer and glass Scratches of polarizer Black spot (in viewing area) Black line (in viewing area) Contents No clear defects Covering all of the chip and no clear crimple Not permitted According to the limit specimen Not permitted Not counted φ