1EDI3020ASXUMA1

EiceDRIVER™ gate driver 1EDI3020AS Single channel isolated IGBT driver Features • • • • • • • • • • • • Single channel isolated IGBT driver using coreless transformer technology For IGBTs up to 1200 V CMTI up to 150 V/ns at 1000 V 8 kV basic insulation according to VDE V 0884-11:2017-01 Basic insulation recognized according to UL 1577 Min. 12 A peak current rail-to-rail output Propagation delay 60 ns typical Typ. 10 A integrated Active Miller Clamp supports unipolar switching Integrated ADC for temperature measurement Integrated safety features to support ASIL B(D): - Redundant DESAT and OCP protection - Gate and output stage monitoring - Shoot-through protection - Primary/secondary supply monitoring - Internal supervision ISO 26262 Safety Element out of Context for safety requirements up to ASIL B Green Product (RoHS compliant) Potential applications • • • Traction inverters for HEV and EV Auxiliary inverters for HEV and EV High power DC/DC converters Product validation Qualified for automotive applications. Product validation according to AEC-Q100. Datasheet Please read the Important Notice and Warnings at the end of this document www.infineon.com/isolated-high-voltage-gate-driver Rev. 1.01 2021-06-25 EiceDRIVER™ gate driver 1EDI3020AS Single channel isolated IGBT driver Description Description The EiceDRIVER™ gate driver 1EDI3020AS is a high-voltage IGBT driver designed for automotive motor drives above 5 kW. The device is based on Infineon’s coreless transformer (CT) technology, providing galvanic insulation between low voltage and high voltage domains. The device has been designed to support 400 V, 600 V and 1200 V IGBT technologies. The device features a high output stage of minimum 12 A peak current. A comprehensive feature set allows advanced protection of the device and the power switch, as well as optimized driver performance and robustness. The device can be connected on the low voltage side (“primary” side) to 5 V and 3.3 V logic. On the high voltage side (secondary side), the device is dimensioned to drive the gate of IGBTs directly. Short propagation delays and controlled internal tolerances lead to a minimal distortion of the PWM signal. In addition, there is a Miller clamping stage with minimum 12 A integrated, which allows unipolar supply of the IGBT. The device features an integrated ADC for temperature measurements and a detailed error diagnosis via a PWM signal. A large panel of safety related functions supports functional safety requirements at system level as per ISO 26262. Besides, these integrated features ease the implementation of a transition to safe-state. Type Package Marking 1EDI3020AS PG-DSO-20 1EDI3020AS Datasheet 2 Rev. 1.01 2021-06-25 EiceDRIVER™ gate driver 1EDI3020AS Single channel isolated IGBT driver Table of contents Table of contents Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Potential applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Product validation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Table of contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 1 Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 2 2.1 Pin configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Pin definitions and functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 3 3.1 3.2 3.3 3.4 General product characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Functional range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Thermal characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Insulation characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12 4 4.1 4.2 4.3 Operating modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Operating modes diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14 Operating modes description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Single failure events in Normal_Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 5 5.1 5.2 Power supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16 Bipolar and unipolar supplies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Electrical characteristics power supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 6 6.1 6.2 Switching characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Functional description switching . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18 Electrical characteristics switching . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 7 7.1 7.2 Protection and monitoring functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 DESAT protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20 Over Current Protection (OCP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 7.3 7.4 7.5 7.6 7.7 Safe turn-off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Shoot Through Protection (STP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Power supply monitoring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Gate monitoring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29 Output stage monitoring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 8 8.1 8.2 Clamping functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 Active Miller clamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 Passive clamping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 9 Analog-to-Digital Converter (ADC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 Datasheet 3 Rev. 1.01 2021-06-25 EiceDRIVER™ gate driver 1EDI3020AS Single channel isolated IGBT driver Table of contents 9.1 9.2 Functional description ADC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37 Electrical characteristics ADC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 10 10.1 10.2 10.3 10.4 10.5 Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 Reset (NRST) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 Ready (RDY) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39 Fault (NFLT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 I/O levels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 DATA read-out . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41 11 11.1 11.2 Application information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 Electrical characteristics external components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 Typical application example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 12 Package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48 Disclaimer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 Datasheet 4 Rev. 1.01 2021-06-25 EiceDRIVER™ gate driver 1EDI3020AS Single channel isolated IGBT driver Block diagram 1 Block diagram GND2 VCC1 P-Supply P-Supply VEE2 GND1 VCC2 INP INN PWM Input Stage NFLT Primary Logic TOUT Secondary Output Stage Switching Control Logic DESAT DESAT CLAMP/GATE NRST OCP EN OCPP OCPN RDY DATA ADC AIP GND2 Figure 1 Datasheet Block diagram 5 Rev. 1.01 2021-06-25 EiceDRIVER™ gate driver 1EDI3020AS Single channel isolated IGBT driver Pin configuration 2 Pin configuration 1 GND1 VEE2 20 2 VCC1 OCPP 19 3 DATA OCPN 18 4 NFLT AIP 17 5 RDY GND2 16 6 NRST DESAT 15 7 EN VCC2 14 8 INN TOUT 13 9 INP GATE/CLAMP 12 10 GND1 VEE2 11 Figure 2 Pin assignment 2.1 Pin definitions and functions Table 1 Pin definition and functions Pin # Pin name I/O Voltage class Function 1 GND1 Ground Primary ground Ground connection for the primary side. 2 VCC1 Supply Primary supply 5 V/3.3 V power supply for the primary side (referring to GND1). 3 DATA Output 5 V primary The data pin is used for ADC or diagnosis data. This pin is a push-pull output which is driving a PWM signal according to the data. 4 NFLT Output 5 V primary The fault open-drain signal is used to report failure events triggered by DESAT or OCP protection. As a result the pin is driven to low. This pin has to be connected externally to VCC1 with a pull-up resistance. 5 RDY Output 5 V primary The ready open-drain signal is used to report failure events like UVLO1, UVLO2, OVLO2, Life Sign Lost, Output Stage Error, Gate Monitoring Error, etc. As a result this pin is driven to low. This pin has to be connected externally to VCC1 with a pull-up resistance. 6 NRST Input 5 V primary The reset signal is used to clear the failure/fault events which triggered RDY or NFLT active low. The signal is clearing an error on rising edge. An internal pull-down resistance is driving this pin to low state in case the pin is floating. 7 EN Input 5 V primary The enable signal allows the logic on the primary side to enable or disable the device. The logic levels are according (table continues...) Datasheet 6 Rev. 1.01 2021-06-25 EiceDRIVER™ gate driver 1EDI3020AS Single channel isolated IGBT driver Pin configuration Table 1 (continued) Pin definition and functions Pin # Pin name I/O Voltage class Function to the used power supply. An internal weak pull-down resistance is disabling the device in case the pin is floating. 8 INN Input 5 V primary The inverting PWM signal is used for monitoring for shoot through protection. An internal weak pull-up resistor to VCC1 drives this input to high state in case the pin is floating. 9 INP Input 5 V primary The non-inverting PWM signal of the driver. An internal weak pull-down resistor to GND1 drives this input to low state in case the pin is floating. 10 GND1 Ground Primary ground Ground connection for the primary side. 11 VEE2 Supply Secondary supply Negative power supply for the secondary side (referring to GND2). 12 GATE/ CLAMP Input/ Output 15 V secondary The gate monitoring and clamp signal is monitoring the gate of the power switch and clamping the gate to VEE2 if the threshold VCLAMP is reached. 13 TOUT Output 15 V secondary The transistor drive voltage signal switches the power switch gate to VCC2 or VEE2, according to the PWM input. 14 VCC2 Supply Secondary supply Positive power supply for the secondary side (referring to GND2). 15 DESAT Input 15 V secondary The desaturation protection signal monitors the voltage across the power switch. An internal current source to VCC2 drives this signal to high level in case it is floating. 16 GND2 Ground Secondary ground Reference ground for the secondary side. 17 AIP Input 5V secondary The ADC function can be used to monitor temperatures at the power switch. An internal current source supplies the external components. 18 OCPN Input 5V secondary The negative over current protection signal is differential therefore it should be always close to OCPP signal. A common-mode filter should be applied to the OCPP signal. 19 OCPP Input 5V secondary The positive over current protection signal is differential therefore it should be always close to OCPN signal. A common-mode filter should be applied to the OCPN signal. An internal weak pull-up resistor drives this input to high state in case the pin is floating. 20 VEE2 Supply Secondary supply Negative power supply for the secondary side (referring to GND2). Datasheet 7 Rev. 1.01 2021-06-25 EiceDRIVER™ gate driver 1EDI3020AS Single channel isolated IGBT driver General product characteristics 3 General product characteristics 3.1 Absolute maximum ratings Table 2 Absolute maximum ratings TJ = -40°C to 150°C; all voltages with respect to ground, pos. current flowing into pin (unless otherwise specified). Absolute maximum ratings are defined as ratings which when being exceeded may lead to destruction of the integrated circuit. Absolute maximum ratings are not subject to production test, specified by design. Parameter Symbol Values Unit Note or condition P-Number Min. Typ. Max. Positive VVCC1_MAX power supply (primary) -0.3 – 7 V Referenced to GND1 PRQ-560 Positive VVCC2_MAX power supply (secondary) -0.3 – 30 V Referenced to GND2 PRQ-561 Negative VVEE2_MAX power supply (secondary) -13 – 0.3 V Referenced to GND2 PRQ-562 Power supply VVCC2voltage VEE2_MAX difference (secondary) VCC2-VEE2 – – 40 V Voltages on any I/O pin on primary side (INP, INN, NRST, DATA, RDY, NFLT, EN) VINx_MAX -0.3 – VVCC1 V + 0.3 AIP voltage VAIP_MAX -0.3 – VVCC2 V + 0.3 DESAT voltage VDESAT_MAX -0.3 – VVCC2 V + 0.3 Referenced to GND2 PRQ-566 OCPP VOCPP_MAX -2.8 – 2.8 V Referenced to GND2 PRQ-788 OCPN VOCPN_MAX -2.8 – 2.8 V Referenced to GND2 PRQ-831 Maximum Clamp/gate voltage VClamp/ VVEE2 – - 0.3 VVCC2 V + 0.3 Referenced to GND2 PRQ-567 VVEE2 – - 0.3 VVCC2 V + 0.3 Referenced to GND2 PRQ-568 Gate_MAX TOUT voltage VOUT_MAX PRQ-563 Referenced to GND1 PRQ-564 PRQ-789 (table continues...) Datasheet 8 Rev. 1.01 2021-06-25 EiceDRIVER™ gate driver 1EDI3020AS Single channel isolated IGBT driver General product characteristics Table 2 (continued) Absolute maximum ratings TJ = -40°C to 150°C; all voltages with respect to ground, pos. current flowing into pin (unless otherwise specified). Absolute maximum ratings are defined as ratings which when being exceeded may lead to destruction of the integrated circuit. Absolute maximum ratings are not subject to production test, specified by design. Parameter Symbol Values Unit Note or condition P-Number Min. Typ. Max. TOUT high output maximum current IOUTH_MAX -15 – – A tMAX = 1.5 µs, non-repetitive PRQ-569 TOUT low output maximum current IOUTL_MAX – – 15 A tMAX = 1.5 µs, non-repetitive PRQ-570 Gate/Clamp low maximum output current IGate/ – – 15 A tMAX = 1.5 µs, non-repetitive PRQ-848 Current on output logic pins (DATA, RDY, NFLT) |IOUTx_MAX| – – 10 mA ESD immunity VESD_HBM -2 – 2 kV Storage temperature Ts_MAX -55 – 150 οC PRQ-575 Junction temperature TJ_MAX -40 – 150 ºC PRQ-790 Clamp_Max 3.2 Functional range Table 3 Functional range PRQ-572 HBM according to AEC Q100-002, CDM according to AEC Q100-011 PRQ-573 TJ = -40°C to 150°C; all voltages with respect to ground, pos. current flowing into pin (unless otherwise specified). Parameter Symbol Values Unit Note or condition P-Number V Referenced to GND1 PRQ-579 Min. Typ. Max. Positive VVCC1 power supply (primary) 3 – 5.5 (table continues...) Datasheet 9 Rev. 1.01 2021-06-25 EiceDRIVER™ gate driver 1EDI3020AS Single channel isolated IGBT driver General product characteristics Table 3 (continued) Functional range TJ = -40°C to 150°C; all voltages with respect to ground, pos. current flowing into pin (unless otherwise specified). Parameter Symbol Values Unit Note or condition P-Number Min. Typ. Max. VCC1 rampup / down slew rate ΙtRP1Ι 0.00 5 – 2 V/µs Positive VVCC2 power supply IGBT (secondary) 14.5 15 17.7 V VCC2 rampup / down slew rate 0.01 5 – 1 V/µs ΙtRP2Ι PRQ-797 Referenced to GND2 PRQ-580 PRQ-798 Negative VVEE2 power supply (secondary) -11.5 -5 0 V VEE2 rampup / down slew rate 0.01 5 – 1 V/µs PRQ-799 Power supply VVCC2-VEE2 voltage difference (secondary) VCC2-VEE2 – – 25 V PRQ-582 Junction temperature TJ -40 – 150 οC PRQ-588 Common mode transient immunity dVISO/dt -150 – 150 kV/µs Voltages on any I/O pin on primary side (INP, INN, NRST, DATA, RDY, NFLT) VINx 0 VVCC1 V 3.3 ΙtRP3Ι – Referenced to GND2 PRQ-581 For voltages up to 1000 V PRQ-589 Referenced to GND1 PRQ-583 Thermal characteristics The thermal capability of the device is depending on the used power module. The following formula and parameters can be used to calculate the maximum switching frequency for a dedicated power module: Datasheet 10 Rev. 1.01 2021-06-25 EiceDRIVER™ gate driver 1EDI3020AS Single channel isolated IGBT driver General product characteristics Figure 3 Formula to calculate the maximum switching frequency in application Where the maximum switching losses are PSW = PDIS2 - PIDLE_sec, Rg is the external gate resistor, CGate is the maximum gate charge of the power switch, and RDSON-OSLN is the internal gate resistor. Note: This formula is only valid if ON/OFF resistors have the same value. 3.3.1 Thermal characteristics parameters Table 4 Thermal characteristics parameters TJ = -40°C to 150°C; all voltages with respect to ground, pos. current flowing into pin (unless otherwise specified). Parameter Symbol Values Unit Note or condition P-Number PRQ-946 Min. Typ. Max. Power PDIS1 Dissipation Primary Chip – 40 – mW TAMB = 25°C, VVCC1 = 5 V, PWM duty cycle = 50%, Normal_Mode, no CLOAD, no RLOAD on TOUT, average value (peak current neglected) Power Dissipation Secondary Chip PDIS2 – 300 – mW TAMB = 25°C, VVCC2 = typ., VVEE2 = typ., PWM PRQ-947 duty cycle = 50%, Normal_Mode, no CLOAD, no RLOAD on TOUT, average value (peak current neglected) Switching frequency fSW – 25 430 kHz VVCC2 = 18 V, VVEE2 = -5 V, CGate = 9 nF, Rg = 6 Ω, TAMB = 25°C PRQ-839 Thermal Resistance Junction to Ambient (25°C) RTHJA – 85 – K/W Tamb = 25°C PRQ-932 Thermal Resistance Junction to Ambient (125°C) RTHJA,125 – 71 – K/W TAMB = 125°C PRQ-975 Thermal Resistance Junction to Case (bottom) RTHJCBOT – 60 – K/W Tamb = 25°C PRQ-933 (table continues...) Datasheet 11 Rev. 1.01 2021-06-25 EiceDRIVER™ gate driver 1EDI3020AS Single channel isolated IGBT driver General product characteristics Table 4 (continued) Thermal characteristics parameters TJ = -40°C to 150°C; all voltages with respect to ground, pos. current flowing into pin (unless otherwise specified). Parameter Symbol Values Unit Note or condition P-Number Min. Typ. Max. Thermal Resistance Junction to Case (top) RTHJCTOP – 52 – K/W Tamb = 25°C PRQ-934 Thermal Resistance Junction to Board (25°C) RTHJBOARD – 45.4 – K/W Tamb = 25°C, power losses on secondary side ≤ 500 mW, power losses on primary side ≤ 50 mW PRQ-1031 Ψ - Pseudo Thermal Resistance Junction to Case (top) RPSIJT – 21 – K/W Tamb = 25°C PRQ-935 Note: 3.4 This thermal data was generated in accordance with JEDEC JESD51 standards. For more information, go to www.jedec.org. Insulation characteristics The device complies with the insulation ratings specified below. Table 5 Insulation characteristics according to DIN VDE V 0884-11:2017-01 Description Symbol Characteristic Unit Installation classification per EN 60664-1, Table 1 for rated mains voltage ≤ 150 VRMS for rated mains voltage ≤ 150 VRMS for rated mains voltage ≤ 150 VRMS – – I-IV I-III I-II – Climatic classification – 40/125/21 – Pollution degree (EN 60664-1) – 2 – Minimum external clearance CLR 8 mm Minimum external creepage CPG 8 mm Minimum comparative tracking index CTI >400 – Maximum repetitive insulation voltage VIORM 1420 VPEAK Highest allowable overvoltage VIOTM 8000 VPEAK Maximum surge insulation voltage VIOSM 8000 V Datasheet 12 Rev. 1.01 2021-06-25 EiceDRIVER™ gate driver 1EDI3020AS Single channel isolated IGBT driver General product characteristics Table 6 Insulation characteristics recognized according to UL 1577 Parameter Symbol Characteristic Unit Insulation withstand voltage / 1 min VISO 5700 V(rms) Insulation test voltage / 1 s VISO 6000 V(rms) Note: Datasheet These insulators are suitable for basic electrical isolation only within safety limit data (i.e. absolute maximum ratings of this device). 13 Rev. 1.01 2021-06-25 EiceDRIVER™ gate driver 1EDI3020AS Single channel isolated IGBT driver Operating modes 4 Operating modes 4.1 Operating modes diagram NRST = 0 | 1 NRST = 0 | 1 Normal_Mode Ready_Mode Outputs: DATA: DIAG RDY = 1 NFLT = 1 >1 Power_Down ice v De Outputs: DATA = DIAG RDY = 0 (pas. clamp) NFLT = 1 De nE rro r vic en ot a Re rea dy 3) +N RS T- >0 -> Inte rna UV LO 1 l Su per vis io T RS +N Ready lost3) -> RDY = 0 1 Error_Mode Outputs: DATA: ADC (EN=1)4) DATA: DIAG (EN=0) RDY = 0 or NFTL = 0 DESAT or OCP -> NFLT = 0 Pri m. EN = 0 Outputs: DATA: ADC RDY = 1 NFLT = 1 Inputs enabled2) Device Ready1) + NRST ->0 ->1 1) dy ->0 EN = 1 1) Device ready: no OSM Error, no Gate Monitoring Error, no OVLO2, no UVLO2, no open pin at OCPx, no Prim. or Sec. Internal Supervision Error, OTP read ok 2) INP & INN are enabled 3) Device not ready: OSM Error, Gate Monitoring Error, OVLO2, UVLO2, OCPx open pin, Sec. Internal Supervision Error, OTP read error 4) At life sign loss ADC signal at DATA pin output is static 0 Figure 4 Note: 4.2 Operating modes state diagram • • Life sign lost will be detected only if communication has been established once. External pull-up required on RDY and NFLT (open drain output) Operating modes description The device has the following modes which it can operate in: • Ready_Mode (not enabled) • Error_Mode (Failure/Fault event occurred) • Normal_Mode (Device enabled) Reset If the NRST signal is low the device keeps its operating mode (no influence on PWM). Further the rising edge on NRST signal will reset the failure/fault event memory. Datasheet 14 Rev. 1.01 2021-06-25 EiceDRIVER™ gate driver 1EDI3020AS Single channel isolated IGBT driver Operating modes Power Down and Start up The device is in Power_Down_Mode at start-up or if an UVLO1 error occurs. In both cases it will not operate. If the device is partly supplied (e.g. VCC1 only) the device will enter Error_Mode. Therefore supplies should rise within the specified slew rates to a valid voltage level according to given operating conditions. Afterwards a rising edge on NRST will bring the device into Ready_Mode (no Failure or Fault Event occurred). Mode Transitions Once in Ready_Mode the change to Normal_Mode can be done with setting EN signal to "high level" (voltage level differs with VCC1 level), changing it to "low level" is also the returning into Ready_Mode. The transition into Error_Mode can only be done with the according events which are: • OCP event • DESAT event • UVLO2 event • OVLO2 event • Sec. Internal Supervision Error • Output Stage Monitor Error • Gate Monitoring Error • OCPx pin open • OTP read error Error_Mode In Error_Mode a "low level" on signal EN will issue diagnosis information on the DATA pin. This diagnosis information states details about the failure root cause. A "high level" on signal EN issues the ADC information, identical to Normal_Mode. A rising edge on NRST and no failure or fault active will transition the device back to Ready_Mode (or to Normal_Mode if signal EN is set). In Ready_Mode diagnosis information is available on the DATA pin. See also the operating modes diagram for further information. 4.3 Single failure events in Normal_Mode Table 7 Single failure events in Normal_Mode Failure Event Output stage reaction Resulting pin status changes DESAT when TOUT = high (VCC2) Safe turn-off NFLT = 0; DATA: ADC (EN = 1), DATA: DIAG (EN = 0) OCP when TOUT = high (VCC2) Safe turn-off NFLT = 0; DATA: ADC (EN = 1), DATA: DIAG (EN = 0) Gate monitoring error Safe turn-off when TOUT = high (VCC2) RDY = 0; DATA: ADC (EN = 1), DATA: DIAG (EN = 0) OSM error Tri-state RDY = 0; DATA: ADC (EN = 1), DATA: DIAG (EN = 0) UVLO2 Normal switch-off RDY = 0; DATA: ADC (EN = 1), DATA: DIAG (EN = 0) OVLO2 Normal switch-off RDY = 0; DATA: ADC (EN = 1), DATA: DIAG (EN = 0) UVLO1 Normal switch-off RDY = 0; DATA = 0 Prim. internal supervision error Normal switch-off RDY = 0; DATA = 0 Sec. internal supervision error Normal switch-off RDY = 0; DATA: ADC (EN = 1), DATA: DIAG (EN = 0) OCPx pin open Normal switch-off RDY = 0; DATA: ADC (EN = 1), DATA: DIAG (EN = 0) Datasheet 15 Rev. 1.01 2021-06-25 EiceDRIVER™ gate driver 1EDI3020AS Single channel isolated IGBT driver Power supply 5 Power supply 5.1 Bipolar and unipolar supplies The device is designed to support two different supply configurations, bipolar supply and unipolar supply. Note: In bipolar supply the driver is typically supplied with a positive voltage of 15 V at VCC2 and a negative voltage of -5 V at VEE2 (referenced to GND2). The negative supply prevents a dynamic turn on due to the additional charge which is generated from the input capacitance current of the power switch times the negative supply voltage. GATE/CLAMP has to be connected to the gate of the power switch in all power supply configurations. 5.2 Electrical characteristics power supply Table 8 Electrical characteristics power supply TJ = -40°C to 150°C; all voltages with respect to ground, pos. current flowing into pin (unless otherwise specified). Parameter Symbol Values Unit Note or condition P-Number Min. Typ. Max. Quiescent IQVCC1 Current Input Chip (VCC1) 3 5 – mA Ready_Mode, all primary I/Os without impact on Ready_Mode open, VVCC1 = 5 V, VVCC2 = 15 V, VVEE2 = -5 V PRQ-937 Operating IQPVCC1_ON – Current VCC1 (TOUT = high (VCC2)) 10 12 mA Normal_Mode, INN = 0, INP = 1, EN = 1, NRST = 1, outputs open,VVCC1 = 5 V, VVCC2 = 15 V, VVEE2 = -5 V PRQ-938 Operating IOPVCC1_OFF – Current VCC1 (TOUT = low (VEE2)) 5.5 7 mA Normal_Mode, INN = 0, INP = 0, EN = 1, PRQ-939 NRST = 1, outputs open, VVCC1 = 5 V, VVCC2 = 15 V, VVEE2 = -5 V Operating IOPVCC2_ON – Current VCC2 (TOUT = high (VCC2)) 11 13 mA Normal_Mode, INN = 0, INP = 1, EN = 1, PRQ-1036 NRST = 1, primary outputs open, OCPx = 0, DESAT = 0, Gate shorted to TOUT, VVCC1 = 5 V, VVCC2 = 15 V, VVEE2 = -5 V, other pins open Operating IOPVCC2_OFF 6 Current VCC2 (TOUT = low (VEE2)) 11 13 mA Normal_Mode, INN = 0, INP = 0, EN = 1, PRQ-1037 NRST = 1, primary outputs open, OCPx = 0, DESAT = 0, Gate shorted to TOUT, VVCC1 = 5 V, VVCC2 = 15 V, VVEE2 = -5 V, other pins open Operating IOPVEE2_ON – Current VEE2 (TOUT = high (VCC2)) 1.5 2 mA Normal_Mode, INN = 0, INP = 1, EN = 1, PRQ-944 NRST = 1, primary outputs open, OCPx = 0, DESAT = 0, Gate shorted to TOUT, VVCC1 = 5 V, VVCC2 = 15 V, VVEE2 = -5 V, other pins open (table continues...) Datasheet 16 Rev. 1.01 2021-06-25 EiceDRIVER™ gate driver 1EDI3020AS Single channel isolated IGBT driver Power supply Table 8 (continued) Electrical characteristics power supply TJ = -40°C to 150°C; all voltages with respect to ground, pos. current flowing into pin (unless otherwise specified). Parameter Symbol Values Unit Note or condition P-Number mA Normal_Mode, INN = 0, INP = 0, EN = 1, PRQ-945 NRST = 1, primary outputs open, OCPx = 0, DESAT = 0, Gate shorted to TOUT, VVCC1 = 5 V, VVCC2 = 15 V, VVEE2 = -5 V, other pins open Min. Typ. Max. Operating IOPVEE2_OFF 0.5 Current VEE2 (TOUT = low (VEE2)) Datasheet 1.5 2 17 Rev. 1.01 2021-06-25 EiceDRIVER™ gate driver 1EDI3020AS Single channel isolated IGBT driver Switching characteristics 6 Switching characteristics 6.1 Functional description switching The voltage on pin TOUT ranges from VVEE2 to VVCC2 (referenced to GND2). The device supports short propagation delay for On and Off switching of tPDON and tPDOFF. 6.2 Electrical characteristics switching Table 9 Electrical characteristics switching TJ = -40°C to 150°C; all voltages with respect to ground, pos. current flowing into pin (unless otherwise specified). Parameter Symbol Values Unit Note or condition P-Number A INP = VVCC1, INN = VGND1, EN = VVCC1, TOUT = VVCC2, CLAMP/GATE = VVEE2, VVCC2 = 15 V, VVEE2 = -5 V, CLOAD= 200 nF PRQ-662 A INP = VGND1, INN = VGND1, EN = VVCC1, TOUT = VVEE2, CLAMP/GATE = VVCC2, VVCC2 = 15 V, VVEE2 = -5 V, CLOAD= 200 nF PRQ-663 Min. Typ. Max. High level output peak current IOUTH - 12 Low level output peak current IOUTL 12 Propagation delay - On tPDON 40 60 120 ns VCC1 = typ., VCC2 = typ., VEE2 = typ., Start: INP rising edge at Vdigital,input(high), Stop: TOUT rising edge at VVEE2 + 1.5 V, no load, no gate resistance PRQ-770 Propagation delay - Off tPDOFF 40 60 120 ns VCC1 = typ., VCC2 = typ., VEE2 = typ., Start: INP falling edge at Vdigital,input(low), Stop: TOUT falling edge at VVCC2 - 1.5 V, no load, no gate resistance PRQ-851 Propagation delay distortion tProp,dis -20 – 20 ns tPDON - tPDOFF, tPDON & tPDOFF measured @ same TJUNC PRQ-803 Propagation delay EN to turn-on (INP = high) tPDENON 10 60 120 ns VVCC1 = typ.; VVCC2 = typ., VVEE2 = typ., INP = high, INN = GND1, TOUT = VVEE2 + 1.5 V, referring to VEE2 (rising edge) PRQ-968 Propagation delay EN to turn-off (INP = high) tPDENOFF 10 60 120 ns VVCC1 = typ., VVCC2 = typ., VVEE2 = typ., INP = high, INN = GND1, TOUT = VVCC2 - 1.5 V referring to VEE2 (falling edge) PRQ-967 TOUT rise time 90 % tRise1 – – 55 ns no CLOAD, no RLOAD, VVCC2 = typ., VVEE2 = typ. VTOUT = VVEE2 + 1.5 V to VTOUT = VVCC2 1.5 V PRQ-801 TOUT rise time 70 % tRise2 – – 35 ns no CLOAD, no RLOAD, VVCC2 = typ., VVEE2 = typ., VTOUT = VVEE2 + 1.5 V to VTOUT = VVCC2 6V PRQ-958 (table continues...) Datasheet 18 Rev. 1.01 2021-06-25 EiceDRIVER™ gate driver 1EDI3020AS Single channel isolated IGBT driver Switching characteristics Table 9 (continued) Electrical characteristics switching TJ = -40°C to 150°C; all voltages with respect to ground, pos. current flowing into pin (unless otherwise specified). Parameter Symbol Values Unit Note or condition P-Number ns No CLOAD, no RLOAD, VVCC2 = typ., VVEE2 = typ., VTOUT = VVCC2 - 1.5 V to VTOUT = VVEE2 + 1.5 V PRQ-802 Ω N-MOS, tolerances according to RDSON-OSLN PRQ-1032 Min. Typ. Max. Fall time tFall – TOUT RDSON RDSONHigh-side OSHN TOUT RDSON RDSONHigh-side OSHtot P&N Datasheet 45 0.30 0.3 TOUT RDSON RDSON-OSLN 0.07 Low-side Note: – – 1 Ω N-MOS and P-MOS, voltage drop VVCC2 VTOUT < 1 V PRQ-849 – 0.35 Ω N-MOS, voltage drop VTOUT - VVEE2 < 1 V PRQ-850 The defined minimum/maximum value of IOUTx is the minimum current which the device delivers under the given conditions. In general the device is capable to delives higher output currents than the defined minimum/maximum. The maximum output current needs to be limited by an external gate resistor to stay inside the defined absolute maximum rating parameters regarding maximum peak current (equivalent energy needs to be considered) and maximum junction temperature. 19 Rev. 1.01 2021-06-25 EiceDRIVER™ gate driver 1EDI3020AS Single channel isolated IGBT driver Protection and monitoring functions 7 Protection and monitoring functions 7.1 DESAT protection 7.1.1 Functional description DESAT protection The device monitors the voltage across the power switch when TOUT = high(VCC2), after the DESAT blanking time is elapsed. If the corresponding reference level (VDESATx) is reached, it issues a safe turn-off within tDESAT2OFF, then changes into Error_Mode and signals a NFLT low in tNFLT_DESAT. Vcc2 Logic NFTL trigger Comp DSAT DESAT Voltage Divider Fixed Vref Clamping_active GND2 Figure 5 DESAT diagram of principal functionality The DESAT pin has an internal clamping which clamps DESAT to VDESATL in case TOUT = low (VEE2), TOUT = VSOffPLT or in case of OSM (tristate). Datasheet 20 Rev. 1.01 2021-06-25 EiceDRIVER™ gate driver 1EDI3020AS Single channel isolated IGBT driver Protection and monitoring functions Internal DESAT CLAMP time GATE VGATEVEEH,min time TOUT time INP tDESATBT time Figure 6 DESAT clamping and blanking timing diagram 7.1.2 Electrical characteristics DESAT protection Table 10 Electrical characteristics DESAT protection TJ = -40°C to 150°C; all voltages with respect to ground, pos. current flowing into pin (unless otherwise specified). Parameter Symbol Values Unit Note or condition P-Number V VCC2 = typ., VEE2 = typ. PRQ-734 Min. Typ. Max. DESAT reference level VDESAT0 8.6 9 DESAT current source IDESATCS -550 -500 -450 µA VVCC2 = typ., VVEE2 = typ., VDESAT ≤ 10 V PRQ-800 DESAT low voltage VDESATL 0 Referenced to GND2, DESAT clamping enabled, Isink = 5 mA PRQ-693 200 9.3 300 mV (table continues...) Datasheet 21 Rev. 1.01 2021-06-25 EiceDRIVER™ gate driver 1EDI3020AS Single channel isolated IGBT driver Protection and monitoring functions Table 10 (continued) Electrical characteristics DESAT protection TJ = -40°C to 150°C; all voltages with respect to ground, pos. current flowing into pin (unless otherwise specified). Parameter Symbol Values Unit Note or condition P-Number Min. Typ. Max. DESAT tDESAT2OFF detection & reaction time 100 300 400 ns VDESAT_Overdrive= 2 V, Slew rate @ DESAT = 10 V/µs; TOUT = VVCC2 - 1.5 V, after DESAT blanking time elapsed, CLOAD_TOUT = no load, no resistive load PRQ-841 DESAT blanking time 120 320 400 ns From VGATEVEEH to release of clamping (Desat pin voltage rising above 0.5 V, with internal current source, no external CDESAT), no CLoad/RLoad on TOUT PRQ-969 0 – VVCC2 V Referenced to GND2 PRQ-690 tDESATBT DESAT input VDESAT voltage range 7.2 Over Current Protection (OCP) 7.2.1 Functional description OCP protection The device monitors the voltage difference between OCPP and OCPN when TOUT = high (VCC2) after the OCP blanking time is elapsed. If the corresponding reference level (VOCPDx) is reached, it issues a safe turn-off within tOCP2OFF, then changes into Error_Mode and signals a NFLT low in tNFLT_OCP. 2.5 V typ. IGBT/SiC Logic OCPP pin open RDY trigger OCPP Comp1 NFLT trigger Rsense Fixed threshold OCPN GND2 RDY trigger OCPN pin open Figure 7 Datasheet OCP diagram of principal functionality 22 Rev. 1.01 2021-06-25 EiceDRIVER™ gate driver 1EDI3020AS Single channel isolated IGBT driver Protection and monitoring functions OCP blanking time GATE VGATEVEEH,min time TOUT time INP tOCPBT time Figure 8 OCP blanking time 7.2.2 Electrical characteristics OCP protection Table 11 Electrical characteristics OCP TJ = -40°C to 150°C; all voltages with respect to ground, pos. current flowing into pin (unless otherwise specified). Parameter Symbol Values Unit Note or condition P-Number VOCPP - VOCPN PRQ-695 Min. Typ. Max. Overcurrent error detection threshold VOCPD1 270 300 330 mV OCPP & RPUOCP2 OCPN pull-up resistance 26 38 50 kΩ OCPP & OCPN voltage -1 – 1 V VOCP PRQ-697 referring to GND2 PRQ-793 (table continues...) Datasheet 23 Rev. 1.01 2021-06-25 EiceDRIVER™ gate driver 1EDI3020AS Single channel isolated IGBT driver Protection and monitoring functions Table 11 (continued) Electrical characteristics OCP TJ = -40°C to 150°C; all voltages with respect to ground, pos. current flowing into pin (unless otherwise specified). Parameter Symbol Values Unit Note or condition P-Number Min. Typ. Max. OCP tOCP2OFF detection & reaction time 100 300 400 ns VOCP_Overdrive = 200 mV, slew rate = 100 mV/ PRQ-842 ns, TOUT = VVCC2 - 1.5 V, after OCP blanking time elapsed, CLOAD_TOUT = no load, no resistive load OCP blanking tOCPBT time 120 320 400 ns From VGATEVEEH to release of blanking. VOCP_Overdrive = 200 mV, slew rate = 100 mV/ns, no CLoad/RLoad on TOUT OCP pin open VOCPOPEN detection voltage 2.2 2.45 2.6 V PRQ-1014 PRQ-1030 7.3 Safe turn-off 7.3.1 Functional description safe turn-off The device enables a two-level turn-off in case of a fault. Datasheet 24 Rev. 1.01 2021-06-25 EiceDRIVER™ gate driver 1EDI3020AS Single channel isolated IGBT driver Protection and monitoring functions VDESAT VDESATx,max time VTOUT VVCC2 VVCC2 – 1.5 V VSOffPLT,typ VSOffPLT,typ – 1.5 V VVEE2 + 1.5 V tDESAT2OFF VVEE2 tSafeOffPLT tPLT2off time Figure 9 Note: Two level turn-off principle for safe turn-off • • Safe turn-off is only enabled at DESAT, OCP and gate monitoring error (if TOUT = high (VCC2) events. DESAT is only used as an example, can be replaced by OCP and gate monitoring. 7.3.2 Electrical characteristics safe turn-off Table 12 Electrical characteristics safe turn-off Parameter Symbol Values Unit Note or condition P-Number Min. Typ. Max. Safe turn-off plateau time tSafeOffPLT Plateau to tPLT2Off turn-off time 1 – 1.5 μs 10 – 50 ns PRQ-918 No RLoad, no CLoad PRQ-973 (table continues...) Datasheet 25 Rev. 1.01 2021-06-25 EiceDRIVER™ gate driver 1EDI3020AS Single channel isolated IGBT driver Protection and monitoring functions Table 12 (continued) Electrical characteristics safe turn-off Parameter Symbol Values Unit Note or condition P-Number V VVCC2 ≥ VSOffPLT,max + 2 V, CLOAD_TOUT = 68 nF, PRQ-919 RLOAD_TOUT = 1.7 Ω Min. Typ. Max. Safe turn-off plateau voltage level VSOffPLT 8.46 9 9.54 7.4 Shoot Through Protection (STP) 7.4.1 Functional description STP The device has a Shoot Through Protection (STP) function to prevent both high-side and low-side switches to be activated simultaneously. Note: STP is always active. However, setting the INN pin to GND1 deactivates the function. If one of the drivers is in ON state, the driver’s counterpart PWM input is inhibited, preventing it to turn on. PWM_HS PWM_LS INP_HS INN_HS HS Driver HS L o g i c OUT_HS LOGIC INP_LS INN_LS Figure 10 Driver LS L o g i c OUT_LS LS Shoot through protection application diagram The device follows the shoot through protection timing diagram shown below: Datasheet 26 Rev. 1.01 2021-06-25 EiceDRIVER™ gate driver 1EDI3020AS Single channel isolated IGBT driver Protection and monitoring functions Keep State INP_HS INP_LS INN_HS TOUT_HS tPDOFF tDEAD tPDON TOUT_LS tPDON tDEAD tPDON Figure 11 Shoot through protection timing diagram 7.4.2 Electrical characteristics STP Table 13 Electrical characteristics STP tPDOFF TJ = -40°C to 150°C; all voltages with respect to ground, pos. current flowing into pin (unless otherwise specified). Parameter Symbol Values Unit Note or condition P-Number Min. Typ. Max. Dead time for tDEAD3 shoot through protection 650 800 950 ns PRQ-729 7.5 Power supply monitoring 7.5.1 Functional description power supply monitoring The device is equipped with an undervoltage lockout for the primary supply (VCC1) and secondary supply (VCC2) in order to ensure correct switching of the power switch. Note: In all under voltage conditions the ASC signal still works until the voltage drops below VASCOFF at VCC2. The device turns off the power switch and ignores signals at INP and INN (goes into Power_Down Mode) if the power supply VCC1 drops below VUVLO1L. It returns to Ready_Mode if the voltage at VCC1 is above VUVLO1H and the device received a rising edge at NRST. The device turns off the power switch within tUVLO22OFF and ignores signals at INP and INN (go into Error_Mode) within tPS2RDY if the power supply VCC2 drops below VUVLO2L_x. It returns to Ready_Mode if the voltage at VCC2 is above VUVLO2H_x and the device received a rising edge at NRST. The device is equipped with an overvoltage lockout for the secondary supply VCC2 in order to prevent damage of the power switch. Datasheet 27 Rev. 1.01 2021-06-25 EiceDRIVER™ gate driver 1EDI3020AS Single channel isolated IGBT driver Protection and monitoring functions Note: The ASC signal will overwrite the turn-off command, which may lead to damage of the power switch (power switch). The device turns off the power switch within tOVLO22OFF and ignores signals at INP and INN (go into Error_Mode) within tPS2RDY if the power supply VVCC2 rises above VOVLO2H_x. It returns to Ready_Mode if the voltage VVCC2 is below VOVLO2L_x and the device received a rising edge at NRST. Note: • • • In Error_Mode, RDY changes to 0. Turn-off means normal switch-off and not a safe turn-off. Exception: ASC function → TOUT = high (VCC2). 7.5.2 Electrical characteristics power supply monitoring Table 14 Electrical characteristics power supply monitoring TJ = -40°C to 150°C; all voltages with respect to ground, pos. current flowing into pin (unless otherwise specified). Parameter Symbol Values Unit Note or condition P-Number Min. Typ. Max. UVLO1 threshold low VUVLO1L 2.6 2.75 – V @ VCC1, referenced to GND1 PRQ-741 UVLO1 threshold high VUVLO1H – 2.85 2.95 V @ VCC1, referenced to GND1 PRQ-740 UVLO1 hysteresis VUVLO1HYS – 80 100 mV OVLO2 threshold high VOVLO2H_3 17.8 18.5 19.0 V @ VCC2, referenced to GND2 PRQ-889 OVLO2 threshold low VOVLO2L_3 17.1 17.7 18.2 V @ VCC2, referenced to GND2 PRQ-890 OVLO2 hysteresis VOVLO2HYS 400 800 – mV VOVLO2H_x - VOVLO2L_x PRQ-896 UVLO2 threshold high VUVLO2H_1 12.2 12.6 13 V @ VCC2, referenced to GND2 PRQ-750 UVLO2 threshold low VUVLO2L_1 11.4 11.8 12.2 V @ VCC2, referenced to GND2 PRQ-752 UVLO2 hysteresis VUVLO2HYS 720 800 880 mV – 500 800 ns UVLO1 tUVLO12OFF detection & reaction time PRQ-742 PRQ-755 Slewrate = 2 V/µs, Overdrive = +/- 300 mV PRQ-914 (table continues...) Datasheet 28 Rev. 1.01 2021-06-25 EiceDRIVER™ gate driver 1EDI3020AS Single channel isolated IGBT driver Protection and monitoring functions Table 14 (continued) Electrical characteristics power supply monitoring TJ = -40°C to 150°C; all voltages with respect to ground, pos. current flowing into pin (unless otherwise specified). Parameter Symbol Values Unit Note or condition P-Number Min. Typ. Max. UVLO2 tUVLO22OFF detection & reaction time – 500 800 ns Slewrate=10 V/µs; Overdrive=+/-200 mV PRQ-915 OVLO2 tOVLO22OFF detection & reaction time – 500 800 ns Slewrate=10 V/µs; Overdrive=+/-200 mV PRQ-916 Power supply tPS2RDY monitoring detection and notification time – – 2.5 µs VCC2 = typ., VEE2 = typ. PRQ-976 7.6 Gate monitoring 7.6.1 Functional description gate monitoring The device monitors in the time frame of tGMBT (dynamic or static) the gate signal VGATE at pin CLAMP/GATE to ensure the signal VTOUT reaches the threshold value of VGATE properly. If monitoring conditions are violated, the device issues a safe turn-off (if TOUT = high (VCC2) in less than tGM-DaR and changes to Error_Mode in less than tRDY_GM. VGATE tGMBTd tGMBTd tGMBTd VGATEVCCH, max VGATEVEEL, min tGM-DaR VTOUT time VVCC2 – 1.5 V VVEE2 + 1.5 V time Figure 12 Datasheet Dynamic gate monitoring timing diagram 29 Rev. 1.01 2021-06-25 EiceDRIVER™ gate driver 1EDI3020AS Single channel isolated IGBT driver Protection and monitoring functions VGATE tGMBTs tGMBTs VGATEVCCH,max VGATEVEEL,min VTOUT tGM-DaR time VVCC2 – 1.5 V VVEE2 + 1.5 V time Figure 13 Static gate monitoring timing diagram 7.6.2 Electrical characteristics gate monitoring Table 15 Electrical characteristics gate monitoring TJ = -40°C to 150°C; all voltages with respect to ground, pos. current flowing into pin (unless otherwise specified). Parameter Symbol Values Unit Note or condition P-Number Min. Typ. Max. Gate monitoring detection and reaction time tGM-DaR 450 650 900 ns VCC2 = typ., VEE2 = typ. PRQ-853 Gate monitoring detection and notification time tRDY_GM – 1.5 2.5 µs VCC2 = typ., VEE2 = typ. PRQ-910 Dynamic gate tGMBTd3 monitoring blanking time 6.99 7.6 8.21 µs VEE2 = typ., VCC2 = typ. PRQ-979 Static gate monitoring blanking time 7.40 7.9 8.40 µs VEE2 = typ., VCC2 = typ. PRQ-983 tGMBTs3 (table continues...) Datasheet 30 Rev. 1.01 2021-06-25 EiceDRIVER™ gate driver 1EDI3020AS Single channel isolated IGBT driver Protection and monitoring functions Table 15 (continued) Electrical characteristics gate monitoring TJ = -40°C to 150°C; all voltages with respect to ground, pos. current flowing into pin (unless otherwise specified). Parameter Symbol Values Unit Note or condition P-Number Min. Typ. Max. Gate VGATEVCCH monitoring VCC2 voltage threshold high level VVCC2 VVCC2 VVCC2 V - 2.3 - 2.1 - 1.9 tGMBT is active PRQ-855 Gate VGATEVCCL monitoring VCC2 voltage threshold low level VVCC2 VVCC2 VVCC2 V - 3.2 - 3 - 2.8 tGMBT is active PRQ-962 Gate VGATEVEEH monitoring VEE2 voltage threshold high level VVEE2 VVEE2 VVEE2 V + 2.8 + 3 + 3.2 tGMBT is active PRQ-963 Gate VGATEVEEL monitoring VEE2 voltage threshold low level VVEE2 VVEE2 VVEE2 V + 1.9 + 2.1 + 2.3 tGMBT is active PRQ-856 7.7 Output stage monitoring 7.7.1 Functional description output stage monitoring The output stage monitoring checks whether the internal output signal is according to the given PWM or ASC input signal in the time frame of tOUTMBTx , otherwise the device issues a tri-state for the output stage in less than tOUTM-DaR and changes to Error_Mode in less than tRDY_OSM. Datasheet 31 Rev. 1.01 2021-06-25 EiceDRIVER™ gate driver 1EDI3020AS Single channel isolated IGBT driver Protection and monitoring functions VTOUT,real VOSMVCCH, max VOSMVEEL, min Short to VEE2 time VTOUT tOUTMBTd tOUTMBTd tOUTMBTd tOUTM-DaR VOSMVCCH, max Tri state VOSMVEEL, min IVCC2/IVEE2 time 90% 10% time Figure 14 Datasheet Dynamic output stage monitoring working principle 32 Rev. 1.01 2021-06-25 EiceDRIVER™ gate driver 1EDI3020AS Single channel isolated IGBT driver Protection and monitoring functions VTOUT,real tOUTMBTs tOUTMBTs VOSMVCCH,max VOSMVEEL,min time tOUTM-DaR VTOUT VOSMVCCH,max Tri state VOSMVEEL,min time IVCC2 90% 10% time Figure 15 Note: Static output stage monitoring working principle The passive clamping at TOUT is working. 7.7.2 Electrical characteristics output stage monitoring Table 16 Electrical characteristics output stage monitoring TJ = -40°C to 150°C; all voltages with respect to ground, pos. current flowing into pin (unless otherwise specified). Parameter Symbol Values Unit Note or condition P-Number ns VCC2 = typ., VEE2 = typ. PRQ-859 Min. Typ. Max. Output stage tOUTM-DaR monitoring detection and reaction time 200 350 500 (table continues...) Datasheet 33 Rev. 1.01 2021-06-25 EiceDRIVER™ gate driver 1EDI3020AS Single channel isolated IGBT driver Protection and monitoring functions Table 16 (continued) Electrical characteristics output stage monitoring TJ = -40°C to 150°C; all voltages with respect to ground, pos. current flowing into pin (unless otherwise specified). Parameter Symbol Values Unit Note or condition P-Number Min. Typ. Max. Output stage tRDY_OSM monitoring detection and notification time – 1.5 2.5 µs VCC2 = typ., VEE2 = typ. PRQ-964 Dynamic output stage monitoring blanking time 600 800 1000 ns VEE2 = typ., VCC2 = typ. PRQ-922 1200 ns VEE2 = typ., VCC2 = typ. PRQ-925 tOUTMBTd3 Static output tOUTMBTs3 stage monitoring blanking time 1000 – Output stage VOSMVCCH monitoring VCC2 voltage threshold high level VVCC2 VVCC2 VVCC2 V - 2.3 - 2.1 - 1.9 tOUTBT is active PRQ-863 Output stage VOSMVCCL monitoring VCC2 voltage threshold low level VVCC2 VVCC2 VVCC2 V - 3.2 - 3 - 2.8 tOUTBT is active PRQ-965 Output stage VOSMVEEH monitoring VEE2 voltage threshold high level VVEE2 VVEE2 VVEE2 V + 2.8 + 3 + 3.2 tOUTBT is active PRQ-966 Output stage VOSMVEEL monitoring VEE2 voltage threshold low level VVEE2 VVEE2 VVEE2 V + 1.9 + 2.1 + 2.3 tOUTBT is active PRQ-864 Datasheet 34 Rev. 1.01 2021-06-25 EiceDRIVER™ gate driver 1EDI3020AS Single channel isolated IGBT driver Clamping functions 8 Clamping functions 8.1 Active Miller clamp 8.1.1 Functional description Active Miller clamp The clamp output is activated if the gate voltage VGATE goes below VGATEVEEL during turn-off. VGATE VGATEVEEL, min time Active Miller Clamp Clamping active Clamping active time INP time Figure 16 Note: Active Miller clamp timing diagram In a half bridge configuration the switched off power switch tends to dynamically turn on during the turn on phase of the opposite power switch. A Miller clamp allows sinking the Miller current across a low impedance path in this high dV/dt situation. Therefore, in many applications the use of a negative supply voltage can be avoided. 8.1.2 Electrical characteristics Active Miller clamp Table 17 Electrical characteristics Active Miller clamp TJ = -40°C to 150°C; all voltages with respect to ground, pos. current flowing into pin (unless otherwise specified). Parameter Symbol Values Unit Note or condition P-Number A TOUT = low (VVEE2), CLAMP/GATE = VCLAMP, VVCC2 = 15 V, VVEE2 = -5 V PRQ-667 Referenced to GND2, no load PRQ-586 Min. Typ. Max. Low level clamp peak current ICLAMPL 9.5 10 CLAMP/GATE VCLAMP/GATE VVEE2 – voltage (table continues...) Datasheet VVCC2 V 35 Rev. 1.01 2021-06-25 EiceDRIVER™ gate driver 1EDI3020AS Single channel isolated IGBT driver Clamping functions Table 17 (continued) Electrical characteristics Active Miller clamp TJ = -40°C to 150°C; all voltages with respect to ground, pos. current flowing into pin (unless otherwise specified). Parameter Symbol Values Unit Note or condition P-Number Ω Voltage drop VVCC2 - VTOUT < 1 V PRQ-852 Min. Typ. Max. CLAMP RDSON RDSON- 0.08 – 0.35 CLAMP 8.2 Passive clamping 8.2.1 Functional description passive clamping If the secondary chip is not supplied, the pin GATE/CLAMP is passively clamped to VEE2. 8.2.2 Electrical characteristics passive clamping Table 18 Electrical characteristics passive clamping TJ = -40°C to 150°C; all voltages with respect to ground, pos. current flowing into pin (unless otherwise specified). Parameter Symbol Values Unit Note or condition P-Number Min. Typ. Max. GATE passive VPCLPG1 clamping voltage (ICLAMP = 10 mA) – – VVEE2 V +2V Secondary chip not supplied (VCC2 floating, VEE2 = 0 V), IClamp = 10 mA PRQ-738 GATE passive VPCLPG2 clamping voltage (ICLAMP = 100 mA) – – VVEE2 V + 2.2 V Secondary chip not supplied (VCC2 floating, VEE2 = 0 V), IClamp = 100 mA PRQ-882 Datasheet 36 Rev. 1.01 2021-06-25 EiceDRIVER™ gate driver 1EDI3020AS Single channel isolated IGBT driver Analog-to-Digital Converter (ADC) 9 Analog-to-Digital Converter (ADC) 9.1 Functional description ADC The device has a Delta-Sigma ADC to measure the power switch temperature. The integrated ADC allows isolated temperature sensing. An internal current source IADC,ref is biasing an external thermal diode of the used power module. The voltage signal VAIP is encoded to a PWM signal that is passed over the isolation barrier to the DATA pin on the primary side. The Total Unadjusted Error is the square sum of errors (INL, EROFF and ERGAIN). Device IADCref AIP ADC DATA Galvanic isolation Figure 17 Note: GND2 Temperature measurement diagram VIADC,effective = (VIADC * ERGAIN / 100) 9.2 Electrical characteristics ADC Table 19 Electrical characteristics ADC TJ = -40°C to 150°C; all voltages with respect to ground, pos. current flowing into pin (unless otherwise specified). Parameter Symbol Values Unit Note or condition P-Number Min. Typ. Max. ADC resolution (table continues...) Datasheet – – 12 bit PRQ-609 37 Rev. 1.01 2021-06-25 EiceDRIVER™ gate driver 1EDI3020AS Single channel isolated IGBT driver Analog-to-Digital Converter (ADC) Table 19 (continued) Electrical characteristics ADC TJ = -40°C to 150°C; all voltages with respect to ground, pos. current flowing into pin (unless otherwise specified). Parameter Symbol Values Unit Note or condition P-Number Min. Typ. Max. Ideal ADC VIADC input voltage full scale – 4.82 – PRQ-794 ADC Gain Error ERGAIN - 1.5 – + 1.5 %FS Refers to VIADC, valid for Input range VAIP VGND2 = 0.4 V...4.4 V PRQ-897 ADC Offset Error EROFF -0.25 – +0.2 5 %FS Refers to VIADC, valid for Input range VAIP VGND2 = 0.4 V...4.4 V PRQ-898 ADC INL INL – 0.02 4 0.07 3 %FS Refers to VIADC, valid for Input range VAIP VGND2 = 0.4 V...4.4 V PRQ-899 ADC DNL DNL – 0.00 7 0.02 5 %FS Refers to VIADC, valid for Input range VAIP VGND2 = 0.4 V...4.4 V PRQ-900 ADC IADCref reference current @hot -205 -200 -195 µA Valid for Input range VAIP - VGND2 = 0.4 V...4.4 PRQ-902 V, Tamb = 125 °C ADC reference current @cold IADCref -206 -186 -195 µA Valid for Input range VAIP - VGND2 = 0.4 V...4.4 PRQ-1038 V, , Tamb = -40 °C ADC sample rate fSAMPLE 2.28 12 bit Datasheet 2.4 2.52 kHz 38 PRQ-903 Rev. 1.01 2021-06-25 EiceDRIVER™ gate driver 1EDI3020AS Single channel isolated IGBT driver Interface 10 Interface 10.1 Reset (NRST) 10.1.1 Functional description NRST The NRST pin is the reset input of the device. All errors cleared with a rising edge on NRST. 10.1.2 Electrical characteristics NRST Table 20 Electrical characteristics NRST TJ = -40°C to 150°C; all voltages with respect to ground, pos. current flowing into pin (unless otherwise specified). Parameter Symbol Values Unit Note or condition P-Number Min. Typ. Max. Minimum tNRST reset duration time 10 – – µs PRQ-764 10.2 Ready (RDY) 10.2.1 Functional description RDY The RDY pin reports whether the device is ready. Note: Ready means: no OSM error, no gate monitoring error, no OVLO2, no UVLO2, no open pin at OCPx, no prim. or sec. internal supervision error, OTP read ok. The RDY pin has a passive clamping. Note: Passive clamping keeps RDY = 0 in case of no supply. 10.2.2 Electrical characteristics RDY Table 21 Electrical characteristics RDY TJ = -40°C to 150°C; all voltages with respect to ground, pos. current flowing into pin (unless otherwise specified). Parameter Symbol Values Unit Note or condition P-Number Min. Typ. Max. RDY open drain output low level VRDY(low) – – 0.5 V VVCC1 ≥ 3.0 V, Iload = 5 mA PRQ-840 RDY output low passive clamping VRDYCLAMP – 0.5 1 V IRDYCLAMP = 500 µA, VCC1 = floating, all I/O = floating PRQ-834 (table continues...) Datasheet 39 Rev. 1.01 2021-06-25 EiceDRIVER™ gate driver 1EDI3020AS Single channel isolated IGBT driver Interface Table 21 (continued) Electrical characteristics RDY TJ = -40°C to 150°C; all voltages with respect to ground, pos. current flowing into pin (unless otherwise specified). Parameter Symbol Values Unit Note or condition P-Number Min. Typ. Max. Power up timing prim. tPUprim – 100 1500 µs Time from UVLO1 release to device operable, secondary chip running PRQ-959 Power up timing sec. tPUsec – 100 1500 µs Time from UVLO2 release to device operable, primary chip running PRQ-960 Time from rising Edge NRST to RDY = high tNRST2RDY 50 – 200 No error detected PRQ-961 ns 10.3 Fault (NFLT) 10.3.1 Functional description NFLT The device has an active low fault pin (NFLT) to report DESAT and OCP short circuit events. If the device switches off the output stage due to a DESAT or OCP event, it goes to Error_Mode and signals the event on pin NFLT with NFLT = 0 within tNFLT_DESAT or tNFLT_OCP. Note: Switch off means safe turn-off. The device keeps the fault signal available unless a reset event takes place. 10.3.2 Electrical characteristics NFLT Table 22 Electrical characteristics NFLT TJ = -40°C to 150°C; all voltages with respect to ground, pos. current flowing into pin (unless otherwise specified). Parameter Symbol Values Unit Note or condition P-Number Min. Typ. Max. OCP event detection to NFLT activation tNFLT_OCP – 1.2 2.3 µs VOCP_Overdrive= +/-200 mV, slew rate = 100 mV/ns, NFLT = 90 %, RPU_NFLT = 1 kΩ PRQ-614 DESAT event detection to NFLT activation tNFLT_DESAT – 1.5 2.5 µs VDESAT_Overdrive= +/-200 mV, slew rate = 10 V/µs, NFLT = 90 %, RPU_NFLT = 1 kΩ PRQ-844 NFLT open drain output low level VNFLT – 0.5 V VVCC1 ≥ 3.0 V; |INFLT| = 5 mA PRQ-791 Datasheet – 40 Rev. 1.01 2021-06-25 EiceDRIVER™ gate driver 1EDI3020AS Single channel isolated IGBT driver Interface 10.4 I/O levels Table 23 I/O levels TJ = -40°C to 150°C; all voltages with respect to ground, pos. current flowing into pin (unless otherwise specified). Parameter Symbol Values Unit Note or condition P-Number Min. Typ. Max. Primary digital input low level 0 – 0.8 V PRQ-704 2 – VVCC1 V PRQ-705 INP high/low tINPPD duration 750 – – ns VVCC1=typ., VVCC2=typ., VVEE2=typ., 50% to 50% PRQ-970 INN high/low tINNPD duration 750 – – ns VVCC1=typ., VVCC2=typ., VVEE2=typ., 50% to 50% PRQ-971 Weak pull RPDIN1 down resistance NRST, EN, INP 40 48 60.5 kΩ PRQ-929 Weak pull up RPDINN resistance INN 40 52 60.5 kΩ PRQ-930 Primary digital input high level Vdigital,inpu t(low) Vdigital,inpu t(high) 10.5 DATA read-out 10.5.1 Functional description DATA In case the device switches to Error_Mode and EN pin is low, diagnostic data are available, starting with the next frame. In Ready_Mode diagnostic data are available. In Normal_Mode and in Error_Mode, when EN pin is high, ADC result data are available. Datasheet 41 Rev. 1.01 2021-06-25 EiceDRIVER™ gate driver 1EDI3020AS Single channel isolated IGBT driver Interface V Error detected: RDY = 0 or NFTL = 0 OPM Normal_Mode Error cleared by NRST rising edge Error_Mode Ready_Mode tPeriod_ADC Normal_Mode tPeriod_diag DATA DIAG pattern ADC pattern ADC pattern EN time V Error detected: RDY = 0 or NFTL = 0 OPM Ready_Mode Error cleared by NRST rising edge Error_Mode Ready_Mode to Normal_Mode tPeriod_diag tPeriod_ADC DATA ADC pattern DIAG pattern EN time Note: Next frame means first rising edge of following pulse Figure 18 DATA pin ADC and diagnostic transition timing diagram The 12 bit ADC data is pulse width modulated to a signal with a period of tPeriod_ADC. The duty cycle for 12 bit ADC data always remains in the range of DADC regardless of the ADC input. The following diagnostic functions are reported in Ready_Mode and in Error_Mode, if EN = 0: • UVLO2 • OVLO2 • Gate monitoring • Output stage monitoring • OCP • DESAT • Sec. internal supervision error (Parity, OTP, PMU_Supervision error) The 8 bit diagnostic functions is pulse width modulated to a signal with a period of tPeriod_Diag. The duty cycle of the DATA pin always remains in the range of DDiag regardless of the diagnostic status. Note: 0% and 100% duties are not allowed at DATA pin. Table 24 BITx BIT 0 Diagnostic read-out at DATA pin Value 0 Description PRIM NOT READY Value 1 Description PRIM READY Example: Single failure DESAT 1 (table continues...) Datasheet 42 Rev. 1.01 2021-06-25 EiceDRIVER™ gate driver 1EDI3020AS Single channel isolated IGBT driver Interface Table 24 BITx (continued) Diagnostic read-out at DATA pin Value Description Value Description Example: Single failure DESAT BIT 1 0 1 1 BIT 2 0 1 1 BIT 3 0 1 1 BIT 4 Reserved (always 0) BIT 5 0 No OSM Error 1 OSM Error 0 BIT 6 0 No GATEMON Error 1 GATEMON Error 0 BIT 7 0 No DESAT Error 1 DESAT Error 1 BIT 8 0 No OCP Error 1 OCP Error 0 BIT 9 0 No UVLO2 Error 1 UVLO2 Error 0 BIT 10 0 No OVLO2 Error 1 OVLO2 Error 0 BIT 11 0 SEC READY 1 SEC NOT READY 0 Result from example diagnostic read-out: Duty cycle = 3.49 % The duty cycle for diagnostic read-out can be calculated using the following formula: Figure 19 Formula to calculate the duty cycle for diagnostic read-out 10.5.2 Electrical characteristics DATA Table 25 Electrical characteristics DATA TJ = -40°C to 150°C; all voltages with respect to ground, pos. current flowing into pin (unless otherwise specified). Parameter Symbol Values Unit Note or condition P-Number No life sign lost, no primary reset PRQ-782 Min. Typ. Max. ADC DATA duty cycle range DADC 0.36 – 99.6 % Diagnostic duty cycle range DDiag 0.36 – 99.6 % PRQ-783 (table continues...) Datasheet 43 Rev. 1.01 2021-06-25 EiceDRIVER™ gate driver 1EDI3020AS Single channel isolated IGBT driver Interface Table 25 (continued) Electrical characteristics DATA TJ = -40°C to 150°C; all voltages with respect to ground, pos. current flowing into pin (unless otherwise specified). Parameter Symbol Values Unit Note or condition P-Number Min. Typ. Max. ADC DATA period tPeriod_ADC 95 100 105 µs PRQ-784 Diagnostic period tPeriod_Diag 95 100 105 µs PRQ-785 DATA output low level VDATA,outpu – 0 0.5 V VVCC1 ≥ 3.0 V, |Iload| = 5 mA PRQ-706 DATA output high level VDATA,outpu VCC1 - 0.5 t(high) V VVCC1 ≥ 3.0 V, |Iload | = 5 mA PRQ-707 Datasheet t(low) VVCC1 – 44 Rev. 1.01 2021-06-25 EiceDRIVER™ gate driver 1EDI3020AS Single channel isolated IGBT driver Application information 11 Application information The external component values are specified as typical values in a typical application. Deviation of the nominal values are specified as min or max values, if applicable. Unless otherwise specified the deviation for external components are: • Resistor: ±10% • Capacitor: -50% ... +30% Note: The following information is given as a hint for the implementation of the device only and shall not be regarded as a description or warranty of a certain functionality, condition or quality of the device. 11.1 Electrical characteristics external components Table 26 Electrical characteristics external components Parameter Symbol Values Unit Note or condition P-Number Min. Typ. Max. Decoupling capacitance (between VCC1 and GND1) CdVCC1 0.55 1.1 – µF Total capacitance refers to 1 µF capacitance + 0.1 µF close to the device. Max value depends on tRP1. PRQ-1002 Decoupling capacitance (between VCC2 and GND2) CdVCC2 – 11 – µF Total capacitance refers to 10 µF capacitance + 1 µF close to the device. Values depend on external CLOAD. Max value depends on tRP2. PRQ-1001 Decoupling capacitance (between VEE2 and GND2) CdVEE2 – 11 – µF Total capacitance refers to 10 µF PRQ-1000 capacitance + 1 µF close to the device. Max value depends on tRP3. Pull-up resistance Rpu – 10 – kΩ Min value depends on IOUTx_MAX. PRQ-1015 Filter resistance RFilter – 1 – kΩ Value must fit to application PRQ-1016 Filter capacitance CFilter – 47 – pF Value must fit to application PRQ-1017 DESAT resistance RDesat 1 2.2 – kΩ Depends on maximum current and on VDESATx deviation. PRQ-1018 DESAT filter capacitance CDesat 50 100 – pF Depends on required response time. PRQ-1019 OCP sense resistor ROCPSense – 0.47 – Ω Value depends on power switch PRQ-1021 specification, voltage rating of OCP pin has to be considered. (table continues...) Datasheet 45 Rev. 1.01 2021-06-25 EiceDRIVER™ gate driver 1EDI3020AS Single channel isolated IGBT driver Application information Table 26 (continued) Electrical characteristics external components Parameter Symbol Values Unit Note or condition P-Number Min. Typ. Max. OCPP filter resistance ROCPP – 10 – Ω Depends on required response time. Consider internal pull-up. PRQ-1022 OCPP filter capacitance COCP – 10 – pF Depends on required response time PRQ-1023 OCPN resistance ROCPN – 10 – Ω Should match to OCPP filter resistor. Consider internal pull-up. PRQ-1024 TOUT resistance RLoad 1.7 – – Ω Min resistor value required according to max output current in functional range. Max value limited by gate monitoring feature. PRQ-1025 – 0 – Ω Optional component. Voltage across resistor impacts Active Miller clamping feature. PRQ-1028 GATE/CLAMP RGATE series resistance 11.2 Typical application example Driver IC µC VCC1 VCC2 VCC2 CdVCC2 VCC1 GND2 CdVCC1 CdVEE2 GND1 RFilter VEE2 INP CFilter RFilter DESAT GND1 CFilter GND1 VCC1 GND2 VEE2 GND1 INN RDesat CDesat DDesat RLoad GND2 DATA TOUT RDY AIP Connect seperatly to GND2 pin! TDIODE Rpu VCC1 RGATE Rpu NFLT GATE/CLAMP NRST OCPP EN OCPN ROCPP RFilter CFilter RFilter GND1 CFilter COCP ROCPN ROCPSense GND2 GND1 Figure 20 Note: Datasheet Typical application example with ADC This is a very simplified example. The function must be verified in the real application. 46 Rev. 1.01 2021-06-25 EiceDRIVER™ gate driver 1EDI3020AS Single channel isolated IGBT driver Package information Package information 1) 7.5 1) (2.35) 2.65 Max 12 6.4 0.35 x 45° 0.15±0.05 Stand off 0°...8° 0.7±0.2 0.25 Seating plane Coplanarity Bottom view 11 11 1 10 10 20 10.3 20 Pin1 marking 1 2) 0.25±0.06 0.5 1) Does not include plastic or metal protrusion of 0.15 max. per side 2) Dambar protrusion shall be maximum 0.1 mm total in excess of lead width All dimensions are in units mm The drawing is in compliance with ISO 128-30, Projection Method 1 [ ] Figure 21 PG-DSO-20 Green Product (RoHS compliant) To meet the world-wide customer requirements for environmentally friendly products and to be compliant with government regulations the device is available as a Green Product. Green Products are RoHS compliant (Pb-free finish on leads and suitable for Pb-free soldering according to IPC/JEDEC J-STD-020). Information on alternative packages Please visit www.infineon.com/packages. Datasheet 47 Rev. 1.01 2021-06-25 EiceDRIVER™ gate driver 1EDI3020AS Single channel isolated IGBT driver Revision history Revision history Revision Date Changes 1.01 2021-06-25 Typo in insulation certification standard corrected 1.0 2021-03-18 Initial datasheet created Datasheet 48 Rev. 1.01 2021-06-25 Trademarks All referenced product or service names and trademarks are the property of their respective owners. Edition 2021-06-25 Published by Infineon Technologies AG 81726 Munich, Germany © 2021 Infineon Technologies AG All Rights Reserved. Do you have a question about any aspect of this document? Email: erratum@infineon.com Document reference IFX-Z8F65960512 IMPORTANT NOTICE The information given in this document shall in no event be regarded as a guarantee of conditions or characteristics (“Beschaffenheitsgarantie”). With respect to any examples, hints or any typical values stated herein and/or any information regarding the application of the product, Infineon Technologies hereby disclaims any and all warranties and liabilities of any kind, including without limitation warranties of non-infringement of intellectual property rights of any third party. In addition, any information given in this document is subject to customer’s compliance with its obligations stated in this document and any applicable legal requirements, norms and standards concerning customer’s products and any use of the product of Infineon Technologies in customer’s applications. The data contained in this document is exclusively intended for technically trained staff. It is the responsibility of customer’s technical departments to evaluate the suitability of the product for the intended application and the completeness of the product information given in this document with respect to such application. WARNINGS Due to technical requirements products may contain dangerous substances. For information on the types in question please contact your nearest Infineon Technologies office. Except as otherwise explicitly approved by Infineon Technologies in a written document signed by authorized representatives of Infineon Technologies, Infineon Technologies’ products may not be used in any applications where a failure of the product or any consequences of the use thereof can reasonably be expected to result in personal injury.