2B6I500-800-450W

ModSTACK TM Data Sheet: 2B6I 500/800-450W Key Data 2 x 3 x 450A AC at 500V AC, water cooled Preliminary Data General Information Stack with IGBT’s, heatsinks, capacitors, drivers and sensors for several inverter applications. These are only technical data! Please read heedful the complete documentation and attend the adopted design environment! Especially the EMC environment and the controller functionality are important. Topology Load Type Cooling Target Application Extra Driver core Monitors Module (Unit1) Module (Unit2) Interface Standards IGBT DC Link + 2B6I Resistive, inductive load Water Industrial Drive Available in Master [M] or Slave [S] Configuration Scale Driver Current-, Voltage-, Temperature-Monitoring n.a. 6x FF800R12KL4C Electrical, opt. optical EN50178, UL94, prepared for UL508C 38000002_B_MB 57000002 Unit 1 B6I Unit 2 = ˜ ˜ DRIVER DC LINK B6I = SIGNAL CONDITIONER & MONITOR INTERFACE = ˜ ˜ DRIVER Product ID (eupec) Drawing No. Circuit Diagram No. Electrical Data Dedicated Line Voltage DC Link Voltage DC Link Over Voltage Within 100µs Shutdown DC Link Current At IUnit2, VUnit2, cos_ϕUnit2 Parameter For Isolation Management Min. Typical Max. VLine VDC IDCLink Input VUnit1 IUnit1 IUnit1_10 500 675 VDCmax 1116 880 VRMS Vav V Aav VRMS ARMS ARMS Voltage Unit1 Continuous Current Unit1 Short-time Current Unit1 ϑ=ϑair_inlet 10s, every 180s, initial load = IUnit1 2B6I500-800-450W1.doc 1 of 10 2003-11-11 ModSTACK Pulse Current Unit1 DC Current at Unit1 Over Current Shutdown Unit1 Switching Freq. Unit1 Power Losses Unit1 Voltage Unit2 Displacement factor Continuous Current Unit2 Short-time Current Unit2 Pulse Current Unit2 DC Current at Unit2 Over Current Shutdown Unit2 Switching Freq. Unit2 Power Losses Unit2 Power Losses (PCB and Capacitor) Filter resistors at Output Unit2 Auxiliary Voltage Auxiliary Power Demand EMC Test TM Data Sheet: 2B6I 500/800-450W Sine half wave 20ms No rotating field, ϑ=ϑair_inlet, Percentage of IUnit1. within 15µs Preliminary Data Apeak Aav % 500 -0,9 +0,9 2x3x 450 2x3x 540 0,4* IUnit2 125 3000 8300 315 18 24 80 2 1 1 1,8 30 Hz W VRMS ARMS IUnit1_DC V=Vunit1_min, I=IUnit1, fsw=fsw1 Depending on Controller fsw1 Ploss1 VUnit2 cos_ϕUnit2 ϑ=ϑwater_inlet, ϑchip 5Hz both B6I separated ϑwater_inlet -25°C -25 2 900 0 0 vAir_PCB Standard atmosphere No Condensation EN60068-2-6, Fc 10..59Hz 0,075mm pAir Rel. H 2B6I500-800-450W1.doc 4 of 10 2003-11-11 ModSTACK TM Data Sheet: 2B6I 500/800-450W Permanence Vibration EN60068-2-6, Fc Shock Protection Degree Pollution Degree Over Voltage Category 10-150Hz, 20 Cycles EN60068-2-27, Ea Halfsine 11ms, 3 pulses Preliminary Data 20 100 IP00 2 III m/s² m/s² 2B6I500-800-450W1.doc 5 of 10 2003-11-11 ModSTACK TM Data Sheet: 2B6I 500/800-450W Derating Curves (IGBT Part) Preliminary Data Current derating at low rotating field frequency (f0). Maximal 100% current is allowed. cos(phi) = 0.64, (motor) Theta_air = 40°C 120 100 80 60 40 20 0 -5 0 5 10 15 20 25 f0 [Hz] 30 35 40 45 50 55 I/I_nom [%] cos(phi) = -0.64, (generator) Theta_air = 40°C 120 100 80 60 40 20 0 -5 0 5 10 15 20 25 f0 [Hz] 30 35 40 45 50 55 2B6I500-800-450W1.doc I/I_nom [%] 6 of 10 2003-11-11 ModSTACK TM Data Sheet: 2B6I 500/800-450W Preliminary Data Current derating at different switching frequencies. See datatable for nominal switching frequency. In this drawing 2500Hz is assumed. Maximal 100% current is allowed. IGBT, cos(phi) = 0.64 Theta_air = 40°C 180 160 140 120 I/I_nom [%] 100 80 60 40 20 0 0 1000 2000 3000 4000 5000 6000 7000 fsw [Hz] FF 400 R12 KL4C FF 800 R17 KF6CB2 FF 1200 R17 KE3 Diode, cos(phi) = 0.64 Theta_air = 40°C 200 180 160 140 I/I_nom [%] 120 100 80 60 40 20 0 0 1000 2000 3000 4000 5000 6000 7000 fsw [Hz] FF 400 R12 KL4C FF 800 R17 KF6CB2 FF 1200 R17 KE3 2B6I500-800-450W1.doc 7 of 10 2003-11-11 ModSTACK TM Data Sheet: 2B6I 500/800-450W IGBT, cos(phi) = - 0.64 Theta_air = 40°C 180 160 140 120 I/I_nom [%] 100 80 60 40 20 0 0 1000 2000 3000 4000 Preliminary Data FF 400 R12 KL4C FF 800 R17 KF6CB2 FF 1200 R17 KE3 5000 6000 7000 fsw [Hz] Diode, cos(phi) = -0.64 Theta_air = 40°C 180 160 140 120 I/I_nom [%] 100 80 60 40 20 0 0 1000 2000 3000 4000 5000 6000 7000 fsw [Hz] FF 400 R12 KL4C FF 800 R17 KF6CB2 FF 1200 R17 KE3 2B6I500-800-450W1.doc 8 of 10 2003-11-11 ModSTACK Miscellaneous TM Data Sheet: 2B6I 500/800-450W Preliminary Data This technical information specifies semiconductor stacks but promises no characteristics. It is valid in combination with the belonging technical notes. This document may be changed without prior notice. Warning! Prior to installation and commissioning all safety notices and warnings and all warning signs attached to the equipment have to be carefully read. Make sure that all warning signs remain in a legible condition and missing or damaged signs are replaced. The safety instructions have to be strictly adhered to. The manual contains detailed information on all technical topics with regard to the eupec ModSTACK. For further details regarding publications of the eupec ModSTACK and information on other publications in the area of ModSTACKs please contact your nearest eupec branch or visit our website: http://www.eupec.com. eupec GmbH 2003. All rights reserved Prepared by Approved by J.Schiele 2003-11-24 H.Nübel 2003-11-24 Date of publication Revision 0 2B6I500-800-450W1.doc 9 of 10 2003-11-11 PowerSTACK 2B6I 500/800-450W, Drawing, Preliminary Data 2B6I500-800-450W1.doc 10 of 10 2003-03-17