6EDL04 family
6EDL04x06xT and 6EDL04N02PR family
200 V and 600 V three-phase gate driver with Over Current Protection (OCP),
Enable (EN), Fault and Integrated Bootstrap Diode (BSD)
Features
Infineon thin-film-SOI-technology
Maximum blocking voltage +600 V
Output source/sink current +0.165 A/-0.375 A
Integrated ultra-fast, low RDS(ON) Bootstrap Diode
Insensitivity of the bridge output to negative
transient voltages up to -50 V given by SOItechnology
Separate control circuits for all six drivers
Detection of over current and under voltage supply
Externally programmable delay for fault clear after
over current detection
'Shut down' of all switches during error conditions
CMOS and LSTTL compatible input (negative logic)
Signal interlocking of every phase to prevent crossconduction
Product summary
VOFFSET (6EDL04x06xT)
VOFFSET (6EDL04N02PR)
IO+/- (typ.)
ton / toff (6EDL04Ixxxx)
ton / toff (6EDL04Nxxxx)
tf/tr (typ. CL=1 nF)
= 620 V max.
= 200 V max.
= +0.165 A / -0.375 A
= 530ns / 490 ns
= 530ns / 530 ns
= 60 ns / 26 ns
Package
DSO-28
TSSOP-28
Potential applications
Home appliance, refrigeration compressors, air-conditioning
Fans, pumps
Motor drives, general purpose inverters
Power tools, light electric vehicles
Product validation
Qualified for industrial applications according to the relevant tests of JEDEC47/20/22.
Description
The device 6ED family – 2nd generation is a full bridge driver to control power devices like MOS-transistors or
IGBTs in 3-phase systems with a maximum blocking voltage of +600 V. Based on the used SOI-technology there
is an excellent ruggedness on transient voltages. No parasitic thyristor structures are present in the device.
Hence, no parasitic latch-up may occur at all temperatures and voltage conditions.
The six independent drivers are controlled at the low-side using CMOS resp. LSTTL compatible signals, down to
3.3 V logic. The device includes an under-voltage detection unit with hysteresis characteristic and an overcurrent detection. The over-current level is adjusted by choosing the resistor value and the threshold level at
pin ITRIP. Both error conditions (under-voltage and over-current) lead to a definite shut down off all six
switches. An error signal is provided at the FAULT open drain output pin. The blocking time after over-current
can be adjusted with an RC-network at pin RCIN. The input RCIN owns an internal current source of 2.8 µA.
Therefore, the resistor RRCIN is optional. The typical output current can be given with 165 mA for pull-up and
375 mA for pull down. Because of system safety reasons a 310 ns interlocking time has been realised. The
function of input EN can optionally be extended with over-temperature detection, using an external NTCresistor (see Figure 1). The monolithic integrated bootstrap diode structures between pins VCC and VBx can be
used for power supply of the high side.
6EDL04 family Datasheet
Please read the Important Notice and Warnings at the end of this document
www.infineon.com/gdThreePhase
1 of 21
Version 2.8
2022-05-12
6EDL04 family
200 V & 600 V three-phase driver with OCP, Enable, Fault and Bootstrap Diode
Ordering information
DC-Bus
VCC
VCC
HIN1,2,3
LIN1,2,3
EN
HIN1,2,3
LIN1,2,3
EN
VB1,2,3
HO1,2,3
To Load
VS1,2,3
5V
FAULT
FAULT
LO1,2,3
RRCIN
CRCIN
RCIN
COM
ITRIP
VSS
Signals HIN1,2,3 and LIN1,2,3
according to Table 1
R Sh
VSS
Figure 1
Typical application diagram
Ordering information
Table 1
Members of 6EDL04 family – 2nd generation
Sales Name
High side control input
HIN1,2,3 and LIN1,2,3
6EDL04I06NT negative logic
6EDL04I06PT positive logic
6EDL04N06PT positive logic
6EDL04N02PR positive logic
Target
Typ. UVLO- Bootstrap Package
transistor Thresholds diode
IGBT
IGBT
MOSFET
MOSFET
11.7 V / 9.8 V
11.7 V / 9.8 V
9 V / 8.1 V
9 V / 8.1 V
Yes
Yes
Yes
Yes
Evaluation board
DSO-28
DSO-28
EVAL-6EDL04I06PT
DSO-28
TSSOP-28 EVAL-6EDL04N02PR
Table of contents
Features ........................................................................................................................................ 1
Product summary ........................................................................................................................... 1
Package ......................................................................................................................................... 1
Potential applications ..................................................................................................................... 1
Product validation .......................................................................................................................... 1
Description .................................................................................................................................... 1
Ordering information ...................................................................................................................... 2
Table of contents ............................................................................................................................ 2
1
Block diagram........................................................................................................................ 3
2
Lead definitions ..................................................................................................................... 4
3
3.1
3.2
3.3
3.4
Functional description ............................................................................................................ 5
Low Side and High Side Control Pins (Pin 2, 3, 4, 5, 6, 7) ....................................................................... 5
EN (Gate Driver Enable, Pin 10) ............................................................................................................... 6
/FAULT (Fault Feedback, Pin 8) ............................................................................................................... 6
ITRIP and RCIN (Over-Current Detection Function, Pin 9, 11) ............................................................... 7
6EDL04 family Datasheet
www.infineon.com/gdThreePhase
2 of 21
Version 2.8
2022-05-12
6EDL04 family
200 V & 600 V three-phase driver with OCP, Enable, Fault and Bootstrap Diode
Table of contents
3.5
3.6
3.7
VCC, VSS and COM (Low Side Supply, Pin 1, 12, 13) ............................................................................... 7
VB1, 2, 3 and VS1, 2, 3 (High Side Supplies, Pin 18, 20, 22, 24, 26, 28) ................................................... 7
LO1,2,3 and HO1,2,3 (Low and High Side Outputs, Pin 14, 15, 16, 19, 23, 27) ....................................... 7
4
4.1
4.2
4.3
4.4
4.5
4.6
Electrical parameters ............................................................................................................. 8
Absolute maximum ratings ..................................................................................................................... 8
Required operation conditions ............................................................................................................... 9
Operating Range...................................................................................................................................... 9
Static logic function table ..................................................................................................................... 10
Static parameters .................................................................................................................................. 10
Dynamic parameters ............................................................................................................................. 13
5
Timing diagrams ................................................................................................................... 14
6
6.1
6.2
6.3
Package information ............................................................................................................. 17
PG-DSO-28 ............................................................................................................................................. 17
PG-TSSOP-28 ......................................................................................................................................... 18
PG-TSSOP-28 (according to PCN 2018-165-A) ...................................................................................... 18
7
Qualification information....................................................................................................... 20
8
Related products................................................................................................................... 20
Revision history............................................................................................................................. 20
1
Block diagram
BOOTSTRAP DIODE-VB1
BIAS NETWORK / VDD2
INPUT NOISE
FILTER
HIN1
LIN1
INPUT NOISE
FILTER
HIN2
INPUT NOISE
FILTER
VB1
BIAS NETWORK - VB1
DEADTIME &
SHOOT-THROUGH
PREVENTION
LATCH
z
HV LEVEL-SHIFTER
+ REVERSE-DIODE
COMPAR
ATOR
UVDETECT
GateDrive
HO1
VS1
BOOTSTRAP DIODE-VB2
LIN2
INPUT NOISE
FILTER
HIN3
INPUT NOISE
FILTER
VB2
BIAS NETWORK - VB2
DEADTIME &
SHOOT-THROUGH
PREVENTION
LATCH
HV LEVEL-SHIFTER
+ REVERSE-DIODE
COMPAR
ATOR
UVDETECT
GateDrive
HO2
VS2
BOOTSTRAP DIODE-VB3
VB3
BIAS NETWORK / VB3
DEADTIME &
SHOOT-THROUGH
PREVENTION
LATCH
HV LEVEL-SHIFTER
+ REVERSE-DIODE
COMPAR
ATOR
UVDETECT
GateDrive
INPUT NOISE
FILTER
LIN3
HO3
VS3
>1
INPUT NOISE
FILTER
EN
ITRIP
VCC
UVDETECT
DELAY
VSS / COM
LEVELSHIFTER
GateDrive
LO1
DELAY
VSS / COM
LEVELSHIFTER
GateDrive
LO2
DELAY
VSS / COM
LEVELSHIFTER
GateDrive
LO3
INPUT NOISE
FILTER
S
VDD2
Q
SET
DOMINANT
LATCH
R
IRCIN
RCIN
COM
FAULT
VSS
>1
6EDL04 family Datasheet
www.infineon.com/gdThreePhase
3 of 21
Version 2.8
2022-05-12
6EDL04 family
200 V & 600 V three-phase driver with OCP, Enable, Fault and Bootstrap Diode
Figure 2
Functional block diagram for 6EDL04I06NT
BOOTSTRAP DIODE-VB1
BIAS NETWORK / VDD2
INPUT NOISE
FILTER
HIN1
LIN1
INPUT NOISE
FILTER
HIN2
INPUT NOISE
FILTER
VB1
BIAS NETWORK - VB1
DEADTIME &
SHOOT-THROUGH
PREVENTION
LATCH
HV LEVEL-SHIFTER
+ REVERSE-DIODE
z
COMPAR
ATOR
UVDETECT
GateDrive
HO1
VS1
BOOTSTRAP DIODE-VB2
LIN2
INPUT NOISE
FILTER
HIN3
INPUT NOISE
FILTER
VB2
BIAS NETWORK - VB2
DEADTIME &
SHOOT-THROUGH
PREVENTION
LATCH
HV LEVEL-SHIFTER
+ REVERSE-DIODE
COMPAR
ATOR
UVDETECT
GateDrive
HO2
VS2
BOOTSTRAP DIODE-VB3
VB3
BIAS NETWORK / VB3
DEADTIME &
SHOOT-THROUGH
PREVENTION
LATCH
HV LEVEL-SHIFTER
+ REVERSE-DIODE
COMPAR
ATOR
UVDETECT
GateDrive
HO3
INPUT NOISE
FILTER
LIN3
VS3
>1
INPUT NOISE
FILTER
EN
ITRIP
VCC
UVDETECT
DELAY
VSS / COM
LEVELSHIFTER
GateDrive
LO1
DELAY
VSS / COM
LEVELSHIFTER
GateDrive
LO2
DELAY
VSS / COM
LEVELSHIFTER
GateDrive
LO3
INPUT NOISE
FILTER
S
VDD2
Q
SET
DOMINANT
LATCH
R
IRCIN
RCIN
COM
FAULT
VSS
>1
Figure 3
Functional block diagram for 6EDL04I06PT, and 6EDL04N06PT / 6EDL04N02PR
2
Table 2
Pin no.
Lead definitions
6EDL04 family lead definitions
Name
Function
1
VCC
Low side power supply
2,3,4
HIN1,2,3
High side logic input (positive or negative logic according to Table 1)
5,6,7
LIN1,2,3
Low side logic input (positive or negative logic according to Table 1)
8
/FAULT
Indicates over-current and under-voltage (negative logic, open-drain output)
9
ITRIP
Analog input for over-current shut down, activates FAULT and RCIN to VSS
10
EN
Enable I/O functionality (positive logic)
11
RCIN
External RC-network to define FAULT clear delay after FAULT-Signal (TFLTCLR)
12
VSS
Logic ground
13
COM
Low side gate driver reference
28,24,20
VB1,2,3
High side positive power supply
6EDL04 family Datasheet
www.infineon.com/gdThreePhase
4 of 21
Version 2.8
2022-05-12
6EDL04 family
200 V & 600 V three-phase driver with OCP, Enable, Fault and Bootstrap Diode
Pin no.
Name
Function
27,23,19
HO1,2,3
High side gate driver output
26,22,18
VS1,2,3
High side negative power supply
16,15,14
LO1,2,3
Low side gate driver output
21,25
nc
Not connected
1
VCC
VB1 28
2
HIN1
HO1 27
3
HIN2
VS1 26
4
HIN3
nc
5
LIN1
VB2 24
6
LIN2
HO2 23
7
LIN3
VS2 22
8
FAULT
nc
9
ITRIP
VB3 20
21
10 EN
HO3 19
11 RCIN
VS3 18
12 VSS
Figure 4
25
nc
17
13 COM
LO1 16
14 LO3
LO2
15
Pin Configuration of 6ED family (signals HIN1,2,3 and LIN1,2,3 according to Table 1)
3
Functional description
3.1
Low Side and High Side Control Pins (Pin 2, 3, 4, 5, 6, 7)
The Schmitt trigger input threshold of them is such to guarantee LSTTL and CMOS compatibility down to 3.3 V
controller outputs. Input Schmitt trigger and noise filter provide beneficial noise rejection to short input pulses
according to Figure 5 and Figure 6.
Vcc
Schmitt-Trigger
HINx
LINx
Schmitt-Trigger
INPUT NOISE
FILTER
UZ=10.5V
HINx
LINx
SWITCH LEVEL
VIH; VIL
Figure 5
5k
INPUT NOISE
FILTER
UZ=10.5V
SWITCH LEVEL
VIH; VIL
Input pin structure for negative logic (left) and positive logic (right)
An internal pull-up of about 75 k (negative logic) pre-biases the input during supply start-up and a ESD zener
clamp is provided for pin protection purposes. The zener diodes are therefore designed for single pulse stress
only and not for continuous voltage stress over 10V. For versions with positive, a 5 k pull-down resistor is used
for this function.
6EDL04 family Datasheet
www.infineon.com/gdThreePhase
5 of 21
Version 2.8
2022-05-12
6EDL04 family
200 V & 600 V three-phase driver with OCP, Enable, Fault and Bootstrap Diode
a)
b)
tFILIN
LIN
HIN
on
off
on
HIN
LIN
a)
tFILIN
off
on
LIN
HIN
off
b)
tFILIN
on
off
on
HIN
LIN
tFILIN
off
HO
LO
Figure 6
off
high
high
LO
HO
on
LO
HO
low
low
HO
LO
Input filter timing diagram for negative logic (left) and positive logic (right)
It is anyway recommended for proper work of the driver not to provide input pulse-width lower than 1 µs.
The 6ED family – 2nd generation provides additionally a shoot through prevention capability which avoids the
simultaneous on-state of two channels of the same leg (i.e. HO1 and LO1, HO2 and LO2, HO3 and LO3). When
two inputs of a same leg are activated, only one leg output is activated, so that the leg is kept steadily in a safe
state.
A minimum dead time insertion of typ. 310 ns is also provided, in order to reduce cross-conduction of the
external power switches.
3.2
EN (Gate Driver Enable, Pin 10)
The signal applied to pin EN controls directly the output stages. All outputs are set to LOW, if EN is at LOW logic
level. The internal structure of the pin is given in Figure 7. The switching levels of the Schmitt-Trigger are here
VEN,TH+ = 2.1 V and VEN,TH- = 1.3 V. The typical propagation delay time is tEN = 780 ns. There is an internal pull down
resistor (75 k), which keeps the gate outputs off in case of broken PCB connection.
IEN+, IEN-
EN
INPUT NOISE
FILTER
VZ= 10.5 V
VEN,TH+,
VEN,TH-
6ED family – 2nd generation
Figure 7
3.3
EN pin structures
/FAULT (Fault Feedback, Pin 8)
/Fault pin is an active low open-drain output indicating the status of the gate driver (see Figure 8). The pin is
active (i.e. forces LOW voltage level) when one of the following conditions occur:
Under-voltage condition of VCC supply: In this case the fault condition is released as soon as the supply
voltage condition returns in the normal operation range (please refer to VCC pin description for more
details).
Over-current detection (ITRIP): The fault condition is latched until current trip condition is finished and
RCIN input is released (please refer to ITRIP pin).
VDD
6ED family –
2nd generation
VCC
RON,FLT
FAULT
Figure 8
>1
from ITRIP-Latch
from uv-detection
/FAULT pin structures
6EDL04 family Datasheet
www.infineon.com/gdThreePhase
6 of 21
Version 2.8
2022-05-12
6EDL04 family
200 V & 600 V three-phase driver with OCP, Enable, Fault and Bootstrap Diode
3.4
ITRIP and RCIN (Over-Current Detection Function, Pin 9, 11)
The 6ED family – 2nd generation provides an over-current detection function by connecting the ITRIP input with
the motor current feedback. The ITRIP comparator threshold (typ 0.44 V) is referenced to VSS ground. An input
noise filter (typ. tITRIPMIN = 230 ns) prevents the driver to detect false over-current events.
Over-current detection generates a hard shut down of all outputs of the gate driver and provides a latched fault
feedback at /FAULT pin. RCIN input/output pin is used to determine the reset time of the fault condition. As
soon as ITRIP threshold is exceeded the external capacitor connected to RCIN is fully discharged. The capacitor
is then recharged by the RCIN current generator when the over-current condition is finished. As soon as RCIN
voltage exceeds the rising threshold of typ VRCIN,TH = 5.2 V, the fault condition releases and the driver returns
operational following the ontrol input pins according to Section 3.1.
3.5
VCC, VSS and COM (Low Side Supply, Pin 1, 12, 13)
VCC is the low side supply and it provides power both to input logic and to low side output power stage. Input
logic is referenced to VSS ground as well as the under-voltage detection circuit. Output power stage is
referenced to COM ground. COM ground is floating respect to VSS ground with a maximum range of operation
of +/-5.7 V. A back-to-back zener structure protects grounds from noise spikes.
The under-voltage circuit enables the device to operate at power on when a typical supply voltage higher than
VCCUV+ is present.
The IC shuts down all the gate drivers power outputs, when the VCC supply voltage is below VCCUV- = 9.8 V
respectively 8.1 V. This prevents the external power switches from critically low gate voltage levels during onstate and therefore from excessive power dissipation.
3.6
VB1, 2, 3 and VS1, 2, 3 (High Side Supplies, Pin 18, 20, 22, 24, 26, 28)
VB to VS is the high side supply voltage. The high side circuit can float with respect to VSS following the external
high side power device emitter/source voltage. Due to the low power consumption, the floating driver stage
can be supplied by bootstrap topology connected to VCC.
The device operating area as a function of the supply voltage is given in Figure 15 and Figure 16.
3.7
LO1,2,3 and HO1,2,3 (Low and High Side Outputs, Pin 14, 15, 16, 19, 23,
27)
Low side and high side power outputs are specifically designed for pulse operation such as gate drive of IGBT
and MOSFET devices. Low side outputs (i.e. LO1,2,3) are state triggered by the respective inputs, while high side
outputs (i.e. HO1,2,3) are edge triggered by the respective inputs. In particular, after an under voltage condition
of the VBS supply, a new turn-on signal (edge) is necessary to activate the respective high side output, while
after a under voltage condition of the VCC supply, the low side outputs switch to the state of their respective
inputs.
6EDL04 family Datasheet
www.infineon.com/gdThreePhase
7 of 21
Version 2.8
2022-05-12
6EDL04 family
200 V & 600 V three-phase driver with OCP, Enable, Fault and Bootstrap Diode
4
Electrical parameters
4.1
Absolute maximum ratings
All voltages are absolute voltages referenced to VSS -potential unless otherwise specified. All parameters are
valid for Ta=25 °C.
Table 3
Absolute maximum ratings
Parameter
Symbol
High side offset voltage1
DSO28
TSSOP28
VS
High side offset voltage (tp 7.0 V
All input pins (HINx, LINx) and EN, ITRIP pin are internally clamped (see abs. maximum ratings)
3
In case of input pulse width at LINx and HINx below 1µ the input pulse may not be transmitted properly
6EDL04 family Datasheet
9 of 21
www.infineon.com/gdThreePhase
1
2
Version 2.8
2022-05-12
6EDL04 family
200 V & 600 V three-phase driver with OCP, Enable, Fault and Bootstrap Diode
4.4
Static logic function table
VCC
VBS
RCIN
ITRIP
ENABLE
FAULT
LO1,2,3
HO1,2,3
VRCIN,TH
0
0
High imp
0
0
* according to Table 1
4.5
Static parameters
VCC = VBS = 15V unless otherwise specified. All parameters are valid for Ta=25 °C.
Table 6
Static parameters
Parameter
Symbol
Values
Unit Test condition
Min.
Typ.
Max.
High level input voltage
VIH
1.7
2.1
2.4
Low level input voltage
VIL
0.7
0.9
1.1
EN positive going threshold
VEN,TH+
1.9
2.1
2.3
EN negative going threshold
VEN,TH-
1.1
1.3
1.5
ITRIP positive going threshold
VIT,TH+
380
445
510
mV
ITRIP input hysteresis
VIT,HYS
45
70
RCIN positive going threshold
VRCIN,TH
-
5.2
6.4
V
RCIN input hysteresis
VRCIN,HYS
-
2.0
-
Input clamp voltage
(HIN and LIN acc. Table 1, EN, ITRIP)
VIN,CLMAP
9
10.3
12
IIN = 4mA
Input clamp voltage at high impedance
(/HIN, /LIN negative logic only)
VIN,FLOAT
-
5.3
5.8
controller output
pin floating
High level output voltage
LO1,2,3
HO1,2,3
VOH
-
VCC -0.7 VCC -1.4
VB -0.7 VB -1.4
IO = 20mA
Low level output voltage
LO1,2,3
VOL
-
VCOM+
0.6
VS + 0.6
IO = -20mA
-
VCOM+
0.2
VS+ 0.2
11
11.7
12.5
8.3
9
9.8
9.5
9.8
10.8
7.5
8.1
8.8
HO1,2,3
VCC and VBS supply
undervoltage positive
going threshold
6EDL04I06NT
6EDL04I06PT
VCC and VBS supply
undervoltage negative
going threshold
6EDL04I06NT
6EDL04I06PT
VCCUV+
VBSUV+
6EDL04N06PT
6EDL04N02PR
VCCUV–
VBSUV–
6EDL04N06PT
6EDL04N02PR
6EDL04 family Datasheet
www.infineon.com/gdThreePhase
10 of 21
V
V
Version 2.8
2022-05-12
6EDL04 family
200 V & 600 V three-phase driver with OCP, Enable, Fault and Bootstrap Diode
Table 6
Static parameters
Parameter
VCC and VBS supply
undervoltage lockout
hysteresis
Symbol
6EDL04I06NT
6EDL04I06PT
VCCUVH
VBSUVH
6EDL04N06PT
6EDL04N02PR
Values
Unit Test condition
Min.
Typ.
Max.
1.2
1.9
-
0.5
0.9
-
1
12.5
V
High side leakage current betw. VS and VSS
ILVS+
High side leakage current betw. VS and VSS
ILVS+1
-
10
-
TJ=125°C,VS=600V
High side leakage current between VSx and
VSy (x=1,2,3 and y=1,2,3)
ILVS–
1
-
10
-
TJ = 125°C
VSx - VSy = 600V
Quiescent current VBS supply (VB only)
IQBS1
-
210
400
HO=low
Quiescent current VBS supply (VB only)
IQBS2
-
210
400
HO=high
Quiescent current VCC
supply (VCC only)
6EDL04I06NT
IQCC1
-
1.1
1.8
-
0.75
1.5
Quiescent current VCC
supply (VCC only)
6EDL04I06NT
-
1.3
2
VLIN=0, VHIN=3.3 V
VVSx=50V
0.75
1.5
VLIN=3.3 V, VHIN=0
VVSx=50V
1.3
2
VLIN=3.3 V, VHIN=0
VVSx=50V
0.75
1.5
VLIN=0, VHIN=3.3 V
VVSx=50V
-
70
100
400
700
1100
-
110
200
6EDL04I06PT
6EDL04N06PT
6EDL04N02PR
IQCC2
6EDL04I06PT
6EDL04N06PT
6EDL04N02PR
Quiescent current VCC
supply (VCC only)
6EDL04I06NT
IQCC3
-
6EDL04I06PT
6EDL04N06PT
6EDL04N02PR
Input bias current
6EDL04I06NT
ILIN+
6EDL04I06PT
6EDL04N06PT
6EDL04N02PR
Input bias current
6EDL04I06NT
ILIN-
6EDL04I06PT
6EDL04N06PT
6EDL04N02PR
Input bias current
6EDL04I06NT
6EDL04I06NT
mA
VS = 600V
VLIN=float. (all)
VVSx=50V (only
bootstrap types)
µA
VLIN=3.3 V
µA
VLIN=0
0
IHIN+
6EDL04I06PT
6EDL04N06PT
6EDL04N02PR
Input bias current
µA
IHIN-
6EDL04I06PT
6EDL04N06PT
6EDL04N02PR
Not subject of production test, verified by characterisation
6EDL04 family Datasheet
www.infineon.com/gdThreePhase
-
70
100
400
700
1100
-
110
200
VHIN=3.3 V
VHIN=0
0
1
11 of 21
Version 2.8
2022-05-12
6EDL04 family
200 V & 600 V three-phase driver with OCP, Enable, Fault and Bootstrap Diode
Table 6
Static parameters
Parameter
Symbol
Values
Min.
Input bias current (ITRIP=high)
IITRIP+
Input bias current (EN=high)
IEN+
Input bias current RCIN (internal current
source)
IRCIN
-
Unit Test condition
Typ.
Max.
45
120
45
120
µA
VENABLE=3.3 V
2.8
Mean output current for load capacity charging IO+
in range from 3 V (20%) to 6 V (40%)
120
Peak output current turn on (single pulse)
IOpk+1
Mean output current for load capacity
discharging in range from 12 V (80%) to 9 V
(60%)
IO-
Peak output current turn off (single pulse)
IOpk-1
165
VRCIN = 2 V
-
mA
240
250
375
VITRIP=3.3 V
CL=10 nF
RL = 0 , tp 500 ns
PWin > 1 µs
10
100
6EDL04I06NT
6EDL04I06PT
6EDL04N06PT
6EDL04N02PR
6EDL04 family Datasheet
www.infineon.com/gdThreePhase
13 of 21
VLIN/HIN = 0 & 3.3 V
Version 2.8
2022-05-12
6EDL04 family
200 V & 600 V three-phase driver with OCP, Enable, Fault and Bootstrap Diode
5
Timing diagrams
tFILIN
tFILIN
tIN
HIN/LIN
HIN/LIN
tIN
tIN < tFILIN
tIN < tFILIN
high
HO/LO
low
HO/LO
HIN/LIN
tIN
HIN/LIN
tIN
tIN > tFILIN
HO/LO
Figure 9
tIN > tFILIN
HO/LO
Timing of short pulse suppression (6EDL04I06NT)
tFILIN
HIN/LIN
tFILIN
tIN
tIN
HIN/LIN
tIN < tFILIN
tIN < tFILIN
high
HO/LO
HIN/LIN
low
HO/LO
tIN
HIN/LIN
tIN
tIN > tFILIN
HO/LO
Figure 10
tIN > tFILIN
HO/LO
Timing of short pulse suppression (6EDL04I06PT, 6EDL04N06PT, 6EDL04N02PR)
LIN1,2,3
1.65V
1.65V
HIN1,2,3
12V
HO1,2,3
3V
DT
DT
12 V
LO1,2,3
3V
Figure 11
Timing of of internal deadtime (input logic according to Table 1)
6EDL04 family Datasheet
www.infineon.com/gdThreePhase
14 of 21
Version 2.8
2022-05-12
6EDL04 family
200 V & 600 V three-phase driver with OCP, Enable, Fault and Bootstrap Diode
EN
tEN
HO1,2,3
LO1,2,3
Figure 12
3V
Enable delay time definition
PWIN
LIN1,2,3
1.65V
1.65V
HIN1,2,3
ton
toff
tr
12V
tf
12V
HO1,2,3
LO1,2,3
3V
Figure 13
3V
PWOUT
Input to output propagation delay times and switching times definition (6EDL04I06NT)
PWIN
LIN1,2,3
1.65V
1.65V
HIN1,2,3
ton
toff
tr
12V
tf
12V
HO1,2,3
LO1,2,3
3V
Figure 14
3V
PWOUT
Input to output propagation delay times and switching times definition (6EDL04I06PT,
6EDL04N06PT, 6EDL04N02PR)
20
V
17.5
VCCMAX , VBSMAX
vCC
vBS
13
VCCUV+, VBSUV+ 11.7
VCCUV-, VBSUV- 9.8
t
IC STATE
OFF
Figure 15
ON
ON
Recommended
Area
ON
Forbidden
Area
ON
ON
Recommended
Area
ON
OFF
Operating areas (6EDL04I06NT, 6EDL04I06PT)
6EDL04 family Datasheet
www.infineon.com/gdThreePhase
15 of 21
Version 2.8
2022-05-12
6EDL04 family
200 V & 600 V three-phase driver with OCP, Enable, Fault and Bootstrap Diode
VCCMAX , VBSMAX
vCC
vBS
20
V
17.5
10.0
VCCUV+, VBSUV+ 9.0
VCCUV-, VBSUV- 8.1
t
IC STATE
OFF
Figure 16
ON
ON
Recommended
Area
ON
Forbidden
Area
ON
ON
ON
Recommended
Area
OFF
Operating Areas (6EDL04N06PT, 6EDL04N02PR)
VRCIN,TH
RCIN
ITRIP
0.1V
0.1V
FAULT
1V
0.5V
tFLT
tFLTCLR
Any
output
Figure 17
3V
tITRIP
ITRIP-Timing
tITRIPMIN
ITRIP
tITRIPMIN
tIN
tIN
high
tFLTCLR
/FAULT
Figure 18
ITRIP Input Timing
6EDL04 family Datasheet
www.infineon.com/gdThreePhase
16 of 21
Version 2.8
2022-05-12
6EDL04 family
200 V & 600 V three-phase driver with OCP, Enable, Fault and Bootstrap Diode
6
6.1
Figure 19
Package information
PG-DSO-28
Package drawing
Dimensions
80.0 80.0 1.5 mm³
therm
[W/mK]
Material
FR4
0.3
Metal (Copper) 70µm
Figure 20
388
PCB reference layout
6EDL04 family Datasheet
www.infineon.com/gdThreePhase
17 of 21
Version 2.8
2022-05-12
6EDL04 family
200 V & 600 V three-phase driver with OCP, Enable, Fault and Bootstrap Diode
6.2
PG-TSSOP-28
Footprint for Reflow soldering
e = 0.65
A = 6.10
L = 1.30
B = 0.40
Figure 21
6.3
Figure 22
Package drawing
PG-TSSOP-28 (according to PCN 2018-165-A)
Package drawing
6EDL04 family Datasheet
www.infineon.com/gdThreePhase
18 of 21
Version 2.8
2022-05-12
6EDL04 family
200 V & 600 V three-phase driver with OCP, Enable, Fault and Bootstrap Diode
Figure 23
PCB reference layout (according to JEDEC 1s0P)
left: Reference layout
right: detail of footprint
Table 8
Data of reference layout
Dimensions
Material
Metal (Copper)
76.2 114.3 1.5 mm³
FR4 (therm = 0.3 W/mK)
70µm (therm = 388 W/mK)
6EDL04 family Datasheet
www.infineon.com/gdThreePhase
19 of 21
Version 2.8
2022-05-12
6EDL04 family
200 V & 600 V three-phase driver with OCP, Enable, Fault and Bootstrap Diode
7
Table 9
Qualification information1
Qualification information
Qualification level
Moisture sensitivity level
Charged device model
ESD
Human body model
RoHS compliant
8
Industrial2
Note: This family of ICs has passed JEDEC’s Industrial
qualification. Consumer qualification level is granted by
extension of the higher Industrial level.
MSL33, 260°C
TSSOP-28/DSO-28
(per IPC/JEDEC J-STD-020)
Class C3 (> 1.0 kV)
(per JESD22-C101)
6EDL04x06xT
Class 2 (per JEDEC standard JESD22-A114)
6EDL04N02PR
Class 1C (per JEDEC standard JESD22-A114)
Yes
Related products
Table 10
Gate Driver ICs
2EDL05I06 /
2EDL05N06
2EDL23I06 /
2EDL23N06
600 V, half-bridge thin-film SOI level shift gate driver with integrated high speed, low RDS(ON)
bootstrap diode, 0.36/0.7 A source/sink current driver, 8pins/14pins package, for MOSFET or IGBT.
600 V, half-bridge thin-film SOI level shift gate driver with integrated high speed, low RDS(ON)
bootstrap diode, with over-current protection (OCP), 2.3/2.8 A source/sink current driver, and one
pin Enable/Fault function for MOSFET or IGBT.
Power Switches
IKD04N60R / RF
IKD06N65ET6
IPD65R950CFD
IPN50R950CE
600 V TRENCHSTOP™ IGBT with integrated diode in PG-TO252-3 package
650 V TRENCHSTOP™ IGBT with integrated diode in DPAK
650 V CoolMOS CFD2 with integrated fast body diode in DPAK
500 V CoolMOS CE Superjunction MOSFET in PG-SOT223 package
iMOTION™ Controllers
iMOTION™ Motor control IC for variable speed drives utilizing sensor-less Field Oriented Control
IRMCK099
(FOC) for Permanent Magnet Synchronous Motors (PMSM).
High performance Motor Control IC for variable speed drives based on field oriented control (FOC)
IMC101T
of permanent magnet synchronous motors (PMSM).
Revision history
Document version Date of release
Description of changes
2.6
Increased the maximum operating ambient temperature to 105 °C
2016-08-05
Updated disclaimer, Delete links to application note
Corrected parameter VHO in section 4.3
2.7
2019-01-11
Updated ESD HBM information, and add package drawing PG-TSSOP28. Editorial change in table 6
2.8
2022-05-12
Remove IF,BSD maximum spec
Qualification standards can be found at Infineon’s web site www.infineon.com
Higher qualification ratings may be available should the user have such requirements. Please contact your Infineon sales
representative for further information.
3
Higher MSL ratings may be available for the specific package types listed here. Please contact your Infineon sales representative for
further information.
6EDL04 family Datasheet
20 of 21
Version 2.8
www.infineon.com/gdThreePhase
2022-05-12
1
2
Trademarks
All referenced product or service names and trademarks are the property of their respective owners.
Edition 2019-03-21
Published by
Infineon Technologies AG
81726 Munich, Germany
© 2022 Infineon Technologies AG.
All Rights Reserved.
Do you have a question about this
document?
Email: erratum@infineon.com
Document reference
IMPORTANT NOTICE
The information given in this document shall in no
event be regarded as a guarantee of conditions or
characteristics (“Beschaffenheitsgarantie”) .
With respect to any examples, hints or any typical
values stated herein and/or any information
regarding the application of the product, Infineon
Technologies hereby disclaims any and all
warranties and liabilities of any kind, including
without limitation warranties of non-infringement of
intellectual property rights of any third party.
In addition, any information given in this document
is subject to customer’s compliance with its
obligations stated in this document and any
applicable legal requirements, norms and standards
concerning customer’s products and any use of the
product of Infineon Technologies in customer’s
applications.
The data contained in this document is exclusively
intended for technically trained staff. It is the
responsibility of customer’s technical departments
to evaluate the suitability of the product for the
intended application and the completeness of the
product information given in this document with
respect to such application.
For further information on the product, technology,
delivery terms and conditions and prices please
contact your nearest Infineon Technologies office
(www.infineon.com).
Please note that this product is not qualified
according to the AEC Q100 or AEC Q101 documents
of the Automotive Electronics Council.
WARNINGS
Due to technical requirements products may contain
dangerous substances. For information on the types
in question please contact your nearest Infineon
Technologies office.
Except as otherwise explicitly approved by Infineon
Technologies in a written document signed by
authorized
representatives
of
Infineon
Technologies, Infineon Technologies’ products may
not be used in any applications where a failure of the
product or any consequences of the use thereof can
reasonably be expected to result in personal injury.
