6MS24017P43W41646NOSA1

TechnicalInformation 6MS24017P43W41646 Preliminarydata Generalinformation  IGBTStackfortypicalvoltagesupto690VRMS Ratedoutputcurrent1175RMS  · High power converter · Wind power · Motor drives  · IHM module with IGBT4 · AlSiC baseplate  Topology B6I  Application Inverter  Load type Resistive, inductive  Semiconductor (Inverter Section) 6x FF1200R17KP4_B2  DC Link 12 mF  Heatsink Water cooled  Implemented sensors Current, voltage, temperature  Driver signals IGBT Electrical  Sales - name 6MS24017P43W41646  SP - No. SP001420674  DC Link Inverter Section ~ ~ ~ Signal conditioning & monitor Driver 3 phases Electrical interface preparedby:OW dateofpublication:2017-06-27 approvedby:YZ revision:2.0 1 TechnicalInformation 6MS24017P43W41646 Preliminarydata Absolutemaximumratedvalues Collector-emitter voltage IGBT; Tvj = 25°C Repetitive peak reverse voltage Diode; Tvj = 25°C VCES 1700 V VRRM 1700 V DC link voltage No switching; t=5s, once a day VDC 1450 V Insulation management according to installation height of 2000 m Vline 690 VRMS Insulation test voltage according to EN 50178, f = 50 Hz, t = 5 s VISOL 2.5 kVRMS Junction temperature under switching conditions Tvjop 150 °C Storage temperature min. Tstor -40 °C Storage temperature max. Tstor 65 °C Operational ambient temperature min. Tamb -25 °C Operational ambient temperature max. Tamb 55 °C Auxiliary voltage Vaux 30 V Switching frequency inverter section fsw2 3.5 kHz Notes Further maximum ratings are specified in the following dedicated sections Characteristicvalues  DCLink min. Rated voltage Continous mode Over voltage shutdown within 150 µs Capacitor 1 s, 30 p, rated tol. ±10 % Maximum ripple current per device, Tamb = 55 °C Balance or discharge resistor per DC link unit VDC typ. max. 1050 V 1300 V CDC 12 mF type Foil Iripple 49 Rb 6 ARMS kΩ Notes Operation above 1100 V subject to reduced operating time according to EN 61071 Reduce short circuit protection over 1200V InverterSection min. typ. max. Rated continuous current VDC = 1050 V, VAC = 690 VRMS, cos(ϕ) = 0.9, fAC sine = 50 Hz, fsw = 2600 Hz, Tinlet = 50°C Rated continuous current for 150% overload capability IAC 150% = 1100 ARMS, ton over = 0.01 s, trecovery = 135 s Over current shutdown within 15 µs IAC OC 2500 Apeak Power losses IAC = 1175 A, VDC = 1050 V, VAC = 690 VRMS, cos(ϕ) = 0.9, fAC sine = 50 Hz, fsw = 2600 Hz, Tinlet = 50 °C Ploss 14500 W IAC 1175 IAC over1 InverterSection(specificcondition) 1767 min. Specific continuous current VDC = 1050 V, VAC = 690 VRMS, cos(ϕ) = -0.9, fAC sine = 12 Hz, fsw = 2100 Hz, Tinlet = 50 °C, Tj ≤ 150 °C preparedby:OW dateofpublication:2017-06-27 approvedby:YZ revision:2.0 2 IACsp ARMS typ. 1400 ARMS max. ARMS TechnicalInformation 6MS24017P43W41646 Preliminarydata Controllerinterface Driver and interface board ref. to separate Application Note DR112  Auxiliary voltage Vaux min. typ. max. 18 24 30 Auxiliary power requirement Vaux = 24 V Paux Digital input level resistor to GND 1.8 kΩ, capacitor to GND 4 nF, logic high = on, min. 15 mA Vin low 0 40 Vin high Digital output level open collector, logic low = no fault, max. 15 mA Vout low V W 4 V 11 15 V 0 1.5 V Vout high 15 V 3.6 V Analog current sensor output inverter section load max 1 mA, @ 1175 ARMS VIU ana2 VIV ana2 VIW ana2 Analog DC link voltage sensor output load max 1 mA, @ 1100 V VDC ana 7.6 V Analog temperature sensor output inverter section (NTC) @TNTC = 72 °C, corresponds to Tj = 138 °C at rated conditions VTheta NTC2 8.6 V Analog temperature sensor output inverter section (Simulated) @TNTC = 72 °C, corresponds to Tj = 138 °C at rated conditions VTheta sim2 8.7 V Over temperature shutdown inverter section load max 1 mA VError OT2 10 V  Minimum on time (IGBT) ton min 5 µs Minimum off time (IGBT) toff min 5 µs Systemdata EMC robustness min. according to IEC 61800-3 at named interfaces max. VBurst 2 kV control VBurst 1 kV aux (24V) Vsurge Storage temperature Operational ambient temperature PCB, DC link capacitor, bus bar, excluding cooling medium Cooling air velocity PCB, DC link capacitor, bus bar, standard atmosphere Humidity no condensation Vibration according to IEC 60721 Shock according to IEC 60721 1 kV Tstor -40 65 °C Top amb -25 55 °C Vair 2 Rel. F 0 Protection degree m/s 85 % 10 m/s² 100 m/s² 250 mm IP00 Pollution degree Dimensions typ. power 2 width x depth x height 1090 Weight 625 90 preparedby:OW dateofpublication:2017-06-27 approvedby:YZ revision:2.0 3 kg TechnicalInformation 6MS24017P43W41646 Preliminarydata Heatsinkwatercooled min. ∆V/∆t 35 Coolant inlet temperature Tinlet -40 Thermal resistance heatsink to per switch ambient Rth,ha Water flow according to coolant specification from Infineon typ. dm³/min Water pressure Cooling channel material max. 0.024 8 bar 45 °C K/W Aluminum Notes Composition of coolant: Water and 52 vol. % Antifrogen N Unit 1 (not installed Overviewofoptionalcomponents Inverter Section Voltage sensor × Current sensor × Temperature sensor × Temperature simulation × DC link capacitors × Collector-emitter Active Clamping × Notes Setting of Active Clamping TVS-Diodes: VZ = 1200V/1600V MA111. Reduce short circuit protection above 1200V DC. preparedby:OW dateofpublication:2017-06-27 approvedby:YZ revision:2.0 4 Unit 3 (not installed) TechnicalInformation 6MS24017P43W41646 Preliminarydata fsw - derating curve IGBT (motor), Diode (generator) VDC = 1050 V, VAC = 690 V, fAC sine = 50/ 12 Hz, cosϕ = +/- 0.9 Tinlet = 50 °C and nom. cooling conditions 120 120 110 110 100 100 90 90 80 80 70 70 IAC/Inom [%] IAC/Inom [%] fAC sine - derating curve IGBT (motor), Diode (generator) VDC = 1050 V, VAC = 690 V, fsw = 2.6 kHz, cosϕ = +/- 0.9 Tinlet = 50 °C and nom. cooling conditions 60 50 60 50 40 40 30 30 20 20 IGBT, cosϕ = 0.9 Diode, cosϕ = -0-9 10 0 0 5 10 15 20 Diode, cosϕ = -0.9 (100%~1175A) IGBT, cosϕ = 0.9 (100%~1175A) 10 25 30 35 40 45 0 1500 50 2000 fAC sine [Hz] 2500 3000 3500 fsw [Hz] Tinlet - derating curve IGBT (motor), Diode (generator) VDC = 1050 V, VAC = 690 VRMS, fAC sine = 50 Hz, cosϕ = 0.9 nom. cooling conditions Analog temperature sensor output VTheta NTC Sensing NTC of heatsink 120 10 110 9 100 8 90 7 6 70 VTheta NTC [V] IAC/Inom [%] 80 60 50 40 5 4 3 30 2 20 0 -25 1 IGBT, cosϕ = 0.85 Diode, cosϕ = -0.85 10 -15 -5 5 15 25 35 45 0 55 Tinlet [°C] preparedby:OW dateofpublication:2017-06-27 approvedby:YZ revision:2.0 0 20 40 TNTC [°C] 5 60 80 100 TechnicalInformation 6MS24017P43W41646 Preliminarydata Tvj,sim vs. IAC - Simulated junction temperatur VDC = 1050 V, VAC = 690 VRMS, fsw = 2.6 kHz, Tinlet = 50 °C and nom. cooling conditions Analog temperature sensor output VTheta sim VDC = 1050 V, VAC = 690 VRMS, fsw = 2.6 kHz, nom. cooling conditions 150 10 fAC sine = 50 Hz fAC sine = 12 Hz fAC sine = 50 Hz fAC sine = 12 Hz 135 9 VTheta sim [V] Tvj,sim [°C] 120 105 8 90 7 75 60 600 700 800 900 1000 1100 6 1200 IAC [A] 0.016 i: 1 2 3 4 ri[K/W]: -0.0009 0.00586 0.00642 0.001146 τi[s]: 0.19 1.94 5.77 44.8 Zth,ha [K/W] 0.012 0.008 0.004 0.1 1 105 115 125 Tvj,sim [°C] Zth,ha - thermal impedance heatsink to ambient per switch nom. cooling conditions 0.000 0.01 95 10 100 1000 t [s] preparedby:OW dateofpublication:2017-06-27 approvedby:YZ revision:2.0 6 135 145 dateofpublication:2017-06-27 approvedby:YZ revision:2.0 7 C 5z p31 D p22 E F 2136 2193-6 21;1 7 2186 2183-6 2156 preparedby:OW 631 6 O5 Kpugtv vjtgcfgf dqnv hqt hcuvgpkpi vjg ewuvqogt dqctf );z* 6 5 321 5 )O41z3* 8-6 1 73-6 1 226 56 28-6 26 1 7 O21 Tgxkukqp p31 UY43 328-2 319-2 2;8-2 244 221-2 94 83-2 64-2 59 31 1 6;2 683-6 4 Æpfgtwpigp 62-6 2;-36 1 292-6 252-6 4 Fcvwo KUQ 24826 Mcpvgp< 222 52-6 27-6 1 p31 5z 34;-5 6;2 683-6 644 3 Pcog GW^rcrgphqw 26 26 Kp Dgctdgkvwpi Gtucv| hþt< F11174562 2 Gtugv|v fwtej< 11 2 07 DE 2.0 C4 Tgxkukqp< Dncvv.Pt/< 7OU3511T28MR5.4YCJ.D.EXVKP Ocv/.Pt/< 52757 weight: ~90kg Uvcem.Dcwitwrrg Fqmwogpvuvcvwu< Dgpgppwpi< GP KUQ 2413 Ygtmuvqhh< Oqfgnn< C11173949 Fcvwo Dgctd/ 41/14/3126 Igrt/ Pqto 94 31 1 46 © Alle Rechte bei INFINEON TECHNOLOGIES AG , auch für den Fall von Schutzrechtanmeldungen. Pcog 594 KUQ 3879 . oM 2 O41z3 Ycvgt eqppgevqt O41z3 ykvj rtqvgevkqp ecr )tgoqxg rtqvgevkqp ecr dghqtg wug* Ocz Vqtswg 36Po Fwtkpi cuugodn{ vjg jqugvjg ycvgt eqppgevqt )jqug pq||ng* owuv dg jgnf 9z p22 244 \wn/ Cdygkejwpi< Qdgthnæejg< Ocáuvcd< 2 < 7 )2 < 21* 3 C D E F TechnicalInformation 6MS24017P43W41646 Preliminarydata Mechanicaldrawing 356 461 43; 592 941 TechnicalInformation 6MS24017P43W41646 Preliminarydata Circuitdiagram PWM U BOT X2:15 PWM U TOP X2:3 PWM V BOT X2:4 PWM V TOP X2:17 PWM W BOT X2:18 PWM W TOP X2:2, X3:5 Phase U Error TNTC Signal conditioning & Gate signals EiceDRIVERTM X2:14 Top U Bottom X2:16, X3:18 Phase V Error Phase W Error X3:19 OT Error X3:7 OV Error X3:17 OC Error X3:4 Sum Error Sensor signals TNTC Failure management X2:10, X2:22 GNDdigital X3:2, X3:14 GNDdigital X4:9, X4:14 GNDdigital X2:8, X2:20 P24 X3:3, X3:15 15V X4:15 15V X4:13 -15V X3:11 VIU ana X3:12 VIV ana X3:13 VIW ana X3:10 VTheta NTC, VTheta sim X3:23 VDC ana EiceDRIVERTM X2:5, X3:6 Top V Bottom EiceDRIVERTM TNTC Power supply Top W Bottom X3:24, X3:25 GNDanalog X5:1 Vaux X5:2 GND X5:3 TE, Shield DC+ DR110 DC- V-Option Voltage measurement High voltage domain 13 1 Low voltage domain X2 (male connector) 14 25 13 1 X3 (male connector) 14 25 X4 (male connector) SV1 (jumper) Th 9 1 15 Tj Setting X3:10 = VTheta NTC 3 (Sensing NTC of IGBT module) X5 (male connector) Setting X3:10 = VTheta sim (default setting) (Simulated junction temperature) preparedby:OW dateofpublication:2017-06-27 approvedby:YZ revision:2.0 8 ModSTACKTM 8 1 Technical Information 6MS24017P43W41646 Preliminary data Terms & Conditions of usage The data contained in this product data sheet is exclusively intended for technically trained staff. You and your technical departments will have to evaluate the suitability of the product for the intended application and the completeness of the product data with respect to such application. This product data sheet is describing the characteristics of this product for which a warranty is granted. Any such warranty is granted exclusively pursuant the terms and conditions of the supply agreement. There will be no guarantee of any kind for the product and its characteristics. Should you require product information in excess of the data given in this product data sheet or which concerns the specific application of our product, please contact the sales office, which is responsible for you (see www.infineon.com, sales&contact). For those that are specifically interested we may provide application notes. Due to technical requirements our product may contain dangerous substances. For information on the types in question please contact the sales office, which is responsible for you. Should you intend to use the Product in aviation applications, in health or live endangering or life support applications, please notify. Please note, that for any such applications we urgently recommend - to perform joint Risk and Quality Assessments; - the conclusion of Quality Agreements; - to establish joint measures of an ongoing product survey, and that we may make delivery depended on the realization of any such measures. If and to the extent necessary, please forward equivalent notices to your customers. Changes of this product data sheet are reserved. Safety Instructions Prior to installation and operation, all safety notices and warnings and all warning signs attached to the equipment have to be carefully read. Make sure that all warning signs remain in a legible condition and that missing or damaged signs are replaced. To installation and operation, all safety notices and warnings and all warning signs attached to the equipment have to be carefully read. Make sure that all warning signs remain in a legible condition and that missing or damaged signs are replaced. prepared by: OW date of publication: 2017-06-27 approved by: YZ revision: 2.0 9