AUIR2085S

Sept 26, 2014 Automotive Grade AUIR2085S HIGH SPEED, 100V, SELF OSCILLATING 50% DUTY CYCLE, HALF-BRIDGE DRIVER Product Summary Features            Simple primary side control solution to enable halfTopology bridge DC-Bus Converters for 48V distributed systems with reduced component count and board space VOFFSET Integrated 50% duty cycle oscillator & half-bridge driver Io+ & I o- (typical) IC in a single SO-8 package Programmable switching frequency with up to 500kHz fOSC (max) max per channel +/- 1A drive current capability optimized for low charge Deadtime MOSFETs HO/LO Pulse Matching Adjustable dead-time 50ns – 200ns Floating channel designed for bootstrap operation up to +100Vdc High and low side pulse width matching to +/- 25ns Package Options Adjustable overcurrent protection Undervoltage lockout and internal soft start Leadfree, RoHS compliant Automotive qualified* Typical Applications    Half-Bridge ≤ 100 V 1.0A & 1.0A 500kHz 50ns – 200ns +/- 25ns 8 - Lead SOIC AUIR2085S DC-DC Converters HEV Auxiliary Converter Battery Management Converters Typical Connection Diagram V IN ( 100 V max) V BIAS ( 10 V – 15 V) DBOOT C BOOT VCC RT OSC CT AU IRS2085 VB CS CBIAS HO S1 L VS R C VO + S2 LO COM * Qualification standards can be found on IR’s web site www.irf.com © 2014 International Rectifier AUIR2085S Table of Contents Page Typical Connection Diagram 1 Description/Feature Comparison 3 Qualification Information 4 Absolute Maximum Ratings 5 Recommended Operating Conditions 5 Dynamic Electrical Characteristics 6 Static Electrical Characteristics 6 Functional Block Diagram 7 Input/Output Pin Equivalent Circuit Diagram 9 Lead Definitions 10 Lead Assignments 10 Package Details 12 Tape and Reel Details 13 Part Marking Information 14 Ordering Information 15 www.irf.com © 2014 International Rectifier 2 AUIR2085S Description The AUIR2085S is a self oscillating half-bridge driver IC with 50% duty cycle ideally suited for 36V – 75V half-bridge DC-bus converters. This product is also suitable for push-pull converters without restriction on input voltage. Each channel frequency is equal to fOSC, which can be set by selecting RT & CT, as for Fig. 1. Dead-time can be controlled through proper selection of CT and can range from 50ns to 200ns, as for Fig.2. Internal soft-start increases the pulse width during power up and maintains pulse width matching for the high and low outputs throughout the start up cycle. Typically soft-start duty cycle varies beginning from 5-10% ramping up to about 50% over 1000 cycles. The AUIR2085S initiates a soft start at power up and after every overcurrent condition. Undervoltage lockout prevents operation if VCC is less than 7.5V. www.irf.com © 2014 International Rectifier 3 AUIR2085S Qualification Information† Qualification Level Moisture Sensitivity Level ESD Machine Model Human Body Model Charged Device Model IC Latch-Up Test RoHS Compliant † †† Automotive (per AEC-Q100) Comments: This family of ICs has passed an Automotive qualification. IR’s Industrial and Consumer qualification level is granted by extension of the higher Automotive level. MSL3†† 260°C SOIC8N (per IPC/JEDEC J-STD-020) Class M2 (+/-200V) (per AEC-Q100-003) Class H1B (+/-1750V) (per AEC-Q100-002) Class C4 (+/-1000V) (per AEC-Q100-011) Class II, Level B (per AEC-Q100-004) Yes Qualification standards can be found at International Rectifier’s web site http://www.irf.com/ Higher MSL ratings may be available for the specific package types listed here. Please contact your International Rectifier sales representative for further information. www.irf.com © 2014 International Rectifier 4 AUIR2085S Absolute Maximum Ratings Absolute Maximum Ratings indicate sustained limits beyond which damage to the device may occur. All voltage parameters are absolute voltages referenced to COM. The thermal resistance and power dissipation ratings are measured under board mounted and still air conditions. Symbol Definition Min. Max. -0.3 150 — 25 High side floating supply offset voltage VB - 25 VB + 0.3 High side floating output voltage Low side output voltage OSC pin voltage CS pin voltage Allowable offset voltage slew rate Package power dissipation @ TA ≤ 25°C Thermal resistance, junction to ambient Junction temperature Storage temperature Lead temperature (soldering, 10 seconds) VB - 0.3 -0.3 -0.3 -0.3 — — — — -55 — VB + 0.3 VCC + 0.3 VCC + 0.3 VCC + 0.3 50 0.625 200 150 150 300 VB High side floating supply voltage VCC Low side supply voltage VS VHO VLO OSC VCS dVs/dt PD RthJA TJ TS TL Units V V/ns W °C/W °C Recommended Operating Conditions For proper operation the device should be used within the recommended conditions. Symbol Definition Min. Max. Units VB High side floating supply voltage VS + 10 VS + 15 † VS Steady state high side floating supply offset voltage 100 V -5 ( ) VCC Supply voltage 10 15 ICC Supply current — 5 mA RT Timing resistor 10 100 kΩ CT Timing capacitor 47 470 pF fosc Operating frequency (per channel) — 500 kHz TA Ambient temperature -40 125 °C † Care should be taken to avoid output switching conditions where the VS node flies inductively below ground by more than 5V. www.irf.com © 2014 International Rectifier 5 AUIR2085S Dynamic Electrical Characteristics VCC = VBS = 12V, CLOAD = 1000pF, and TA = 25°C unless otherwise specified. Symbol tr tf fOSC tDT tDCS PM Definition Turn-on rise time Turn-off fall time Per channel output frequency HO/LO output dead time Overcurrent shut down delay HO/LO pulse width mismatch Min — — 500 50 — -25 Typ 40 20 — — 200 — Max Units Test Conditions 60 ns VS = 0V 30 — kHz CT = 100pF, RT = 10kΩ — ns — Pulse on CS 25 VS = 0V ~ 100V Static Electrical Characteristics VCC = VBS = 12V, CLOAD = 1000pF, and TA = 25°C unless otherwise specified. Symbol Definition Min Typ Max Units VOH VOL IIeak IQBS IQCC VCS+ VCSVCCUV+ VCCUV- High level output voltage, VCC or VBS – VO Low level output voltage Offset supply leakage current Quiescent VBS supply current Quiescent VCC supply current Overcurrent shutdown threshold Overcurrent shutdown threshold Undervoltage positive going threshold Undervoltage negative going threshold High side undervoltage positive going threshold High side undervoltage negative going threshold Output high short circuit current Output low short circuit current — — — — — 250 150 6.8 6.3 — — — — — 300 200 7.3 6.8 1.5 0.1 50 150 1.5 350 250 7.8 7.3 6.8 7.3 7.8 6.3 6.8 7.3 — — 1.0 1.0 — — VBSUV+ VBSUVIO+ IO- www.irf.com Test Conditions V µA mA mV mV V A © 2014 International Rectifier 6 AUIR2085S Functional Block Diagram AUIR2085S COM www.irf.com © 2014 International Rectifier 7 AUIR2085S www.irf.com © 2014 International Rectifier 8 AUIR2085S Input/Output Pin Equivalent Circuit Diagrams VCC ESD Diode ESD Diode CS RESD ESD Diode ESD Diode COM www.irf.com © 2014 International Rectifier 9 AUIR2085S Lead Definitions PIN Symbol 1 2 3 4 5 6 7 8 CS OSC COM LO VCC VS HO VB Description Current sense input Oscillator pin Logic supply return Low side output Logic supply Floating supply return High side output High side floating supply Lead Assignments www.irf.com © 2014 International Rectifier 10 AUIR2085S Pin Descriptions Cs: The input pin to the overcurrent comparator. Exceeding the overcurrent threshold value specified in “Static Electrical Parameters” Section will terminate output pulses and start a new soft start cycle as soon as the voltage on the pin reduce below the threshold value. OSC: The oscillator-programming pin. Only two components are required to program the internal oscillator frequency: a resistor connected between the VCC pin and the OSC pin, and a capacitor connected from the OSC to COM. The expected oscillator frequency is shown in Figure 1. The recommended range of timing resistors RT is between 10kΩ and 100kΩ and range of timing capacitor CT is between 47pF and 470pF. Timing resistors values less than 10kΩ should be avoided. The value of the timing capacitor determines the amount of dead time between the two output drivers: lower the CT, shorter the dead time and vice versa. It is not recommended to use a timing capacitor below 47pF, for best performance keep the timing components physically as close as possible to the AUIR2085S. Separated ground and VCC traces to the timing components are encouraged. COM: Signal ground and power ground for all functions. Due to high current and high frequency operation, a low impedance circuit board ground plane is highly recommended. HO, LO: High side and low side gate drive pins. The high and low side drivers can directly drive the gate of a power MOSFET. The drivers are capable of 1A peak source and sink currents. It is recommended that the high and low drive pins be very close to the gates of the high side and low side MOSFETs to prevent any delay and distortion of the drive signals. VB: The high side power input connection. The high side supply is derived from a bootstrap circuit using a low-leakage Schottky diode and a ceramic capacitor. To prevent noise, the Schottky diode and bypass capacitor should be very close to the AUIR2085S. VS: The high side power return connection. VS should be connected directly to the source terminal of high side MOSFET with a trace as short as possible. VCC: The IC bias input connection for the device. Although the quiescent VCC current is very low, total supply current will be higher, depending on the gate charge of the MOSFETs connected to the HO and LO pins, and the programmed oscillator frequency, total VCC current is the sum of quiescent VCC current and the average current at HO and LO. Knowing the operating frequency and the MOSFET gate charge (Qg) at selected VCC voltage, the average current (including bootstrap function) can be calculated from: Iave = 2 x Qg X fOSC To prevent noise problem, a bypass ceramic capacitor connected to VCC and COM should be placed as close as possible to the AUIR2085S. AUIR2085S has an under voltage lookout feature for the IC bias supply, VCC. The minimum voltage required on VCC to make sure that IC will work within specifications must be higher than 8.5V (10V minimum VCC is recommended to prevent asymmetrical gates signal on HO and LO pins that are expected when VCC is between 7.5V and 8.5V). www.irf.com © 2014 International Rectifier 11 AUIR2085S Package Details: www.irf.com © 2014 International Rectifier 12 AUIR2085S Tape and Reel Details: LOADED TAPE FEED DIRECTION A B H D F C NOTE : CONTROLLING DIMENSION IN MM E G CARRIER TAPE DIMENSION FOR 8SOICN Metric Imperial Code Min Max Min Max A 7.90 8.10 0.311 0.318 B 3.90 4.10 0.153 0.161 C 11.70 12.30 0.46 0.484 D 5.45 5.55 0.214 0.218 E 6.30 6.50 0.248 0.255 F 5.10 5.30 0.200 0.208 G 1.50 n/a 0.059 n/a H 1.50 1.60 0.059 0.062 F D C B A E G H REEL DIMENSIONS FOR 8SOICN Metric Code Min Max A 329.60 330.25 B 20.95 21.45 C 12.80 13.20 D 1.95 2.45 E 98.00 102.00 F n/a 18.40 G 14.50 17.10 H 12.40 14.40 Imperial Min Max 12.976 13.001 0.824 0.844 0.503 0.519 0.767 0.096 3.858 4.015 n/a 0.724 0.570 0.673 0.488 0.566 www.irf.com © 2014 International Rectifier 13 AUIR2085S Part Marking Information www.irf.com © 2014 International Rectifier 14 AUIR2085S Ordering Information Standard Pack Base Part Number AUIR2085S Package Type SOIC8 Complete Part Number Form Quantity Tube/Bulk 95 AUIR2085S Tape and Reel 2500 AUIR2085STR IMPORTANT NOTICE www.irf.com © 2014 International Rectifier 15 AUIR2085S Unless specifically designated for the automotive market, International Rectifier Corporation and its subsidiaries (IR) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or services without notice. Part numbers designated with the “AU” prefix follow automotive industry and / or customer specific requirements with regards to product discontinuance and process change notification. All products are sold subject to IR’s terms and conditions of sale supplied at the time of order acknowledgment. IR warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with IR’s standard warranty. Testing and other quality control techniques are used to the extent IR deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. IR assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using IR components. To minimize the risks with customer products and applications, customers should provide adequate design and operating safeguards. Reproduction of IR information in IR data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alterations is an unfair and deceptive business practice. IR is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of IR products or serviced with statements different from or beyond the parameters stated by IR for that product or service voids all express and any implied warranties for the associated IR product or service and is an unfair and deceptive business practice. IR is not responsible or liable for any such statements. IR products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or in other applications intended to support or sustain life, or in any other application in which the failure of the IR product could create a situation where personal injury or death may occur. Should Buyer purchase or use IR products for any such unintended or unauthorized application, Buyer shall indemnify and hold International Rectifier and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that IR was negligent regarding the design or manufacture of the product. IR products are neither designed nor intended for use in military/aerospace applications or environments unless the IR products are specifically designated by IR as military-grade or “enhanced plastic.” Only products designated by IR as military-grade meet military specifications. Buyers acknowledge and agree that any such use of IR products which IR has not designated as military-grade is solely at the Buyer’s risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. IR products are neither designed nor intended for use in automotive applications or environments unless the specific IR products are designated by IR as compliant with ISO/TS 16949 requirements and bear a part number including the designation “AU”. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, IR will not be responsible for any failure to meet such requirements. For technical support, please contact IR’s Technical Assistance Center http://www.irf.com/technical-info/ WORLD HEADQUARTERS: 101 N. Sepulveda Blvd., El Segundo, California 90245 Tel: (310) 252-7105 www.irf.com © 2014 International Rectifier 16