Automotive Grade
AUIRS20162S
Features
Product Summary
Leadfree, RoHS compliant
Automotive qualified
One high side output and internal low side Vs
recharge.
CMOS Schmitt trigger inverted input with pull up
resistor
CMOS Schmitt trigger inverted reset with pull
down resistor
5V compatible logic level inputs
Immune to –Vs spike and tolerant to dVs/dt
Typical Applications
Common Rail Injections
Diesel/Gasoline Direct Injections
Solenoid Drivers
Actuators and brushed DC motors
Low side input, high side
driver with Vs recharge
Topology
VOFFSET
150 V
4.4 V – 20 V
VOUT
Io+ & I o- (typical)
0.25 A
tON & tOFF (typical)
150 ns
Deadtime DTON /
DTOFF (typical)
70ns / 6 us
Package Options
8 - Lead SOIC
AUIRS20162S
Typical Connection Diagram
Cvcc
5V
Logic
Level
Input
Logic
Level
Reset
VCC
VB
INNC
HO
AUIRS20162S
Cbs
GND
NC
RESET-
VS
7V
Standard Pack
Orderable Part Number
AUIRS20162S(TR)
1
www.irf.com
Note
Package Type
SOIC8
© 2014 International Rectifier
Form
Quantity
Tape and Reel
2500
Submit Datasheet Feedback
December 10, 2014
AUIRS20162S
Absolute Maximum Ratings
Absolute maximum ratings indicate sustained limits beyond which damage to the device may occur. These are
stress ratings only, functional operation of the device at these or any other condition beyond those indicated in the
“Recommended Operating Condition” is not implied. Exposure to absolute maximum-rated conditions for
extended periods may affect device reliability. All voltage parameters are absolute voltages referenced to GND
unless otherwise stated in the table. The thermal resistance and power dissipation ratings are measured under
board mounted and still air conditions.
Symbol
VBS
VB
VS
VHO
VCC
VIN
IIN
VRES
dV/dt
RthJA
TJ
TS
Definition
Min.
Max.
Units
High Side Floating Supply Voltage
High Side Driver Output Stage Voltage,
Neg. transient: 0.5 ms, external MOSFET off
High Side Floating Supply Offset Voltage
Neg. transient 0.4 µs
Output Voltage Gate Connection
Supply Voltage
Input Voltage
Input Injection Current. Full function, no latch-up;
(guaranteed by design). Test at 5V and 7V on Eng. Samples.
Reset Input Voltage
Allowable Offset Voltage Slew Rate
Thermal resistance, junction to ambient
Junction Temperature
Storage Temperature
-0.3
-5.0
20
166
V
V
-8.0
150
V
VS – 0.3
-0.3
-0.3
---
VB + 0.3
20
VCC + 0.3
+1
V
V
V
mA
-0.3
-50
-55
-55
VCC + 0.3
50
200
150
150
V
V/nsec
°C/W
ºC
ºC
Max.
VS+20
150
VB
6.5
VCC
VCC
125
200
-----
Units
V
V
V
V
V
V
ºC
kHz
ns
ns
Recommended Operating Conditions
For proper operations the device should be used within the recommended conditions.
Symbol
Definition
Min.
†
High Side Driver Output Stage Voltage
VS+4.4
VB
VS
High Side Floating Supply Offset Voltage
-3
VHO
Output Gate Voltage
VS
††††
Supply Voltage
4.4
VCC
VIN
Input Voltage
0
VRES
Reset Input Voltage
0
Ta
Ambient Temperature
-40
††
fs
--Switching frequency (load: 50 Ohm, 2.5nF into VS)
†††
1000
tinlow_min
Minimum low input width
†††
60
tinhigh_min
Minimum high input width
†
Reset-logic functional for VBS > 2V
Duty cycle = 0.5, VBS = 7 V
†††
Guaranteed by design. Pulse width below the specified values may be ignored. Output will either follow the
input or will ignore it. No false output state is guaranteed when minimum input width is smaller than tin.
††††
Logic operation functional for Vcc > 2.7V, see also table Table 1 on page 10.
††
2
www.irf.com
© 2014 International Rectifier
Submit Datasheet Feedback
December 10, 2014
AUIRS20162S
Electrical Characteristics
Unless otherwise specified, VCC = 5V, VBS = 7V, VS = 0V, IN = 0V, RES = 5V, load R = 50, C = 2.5nF. Unless
otherwise noted, these specifications apply for an operating junction temperature range of -40C Tj 125C.
Symbol
Definition
Min
Typ
Max
Units
Test Conditions
VCC Supply Characteristics
VCCUV+
VCC Supply Undervoltage
Positive Going Threshold
VCCUVVCC Supply Undervoltage
Negative Going Threshold
VCCUVHYS
VCC Supply Undervoltage
Lockout Hysteresis
tdUVCC
Undervoltage Lockout
Response Time
IQCC
VCC Supply Current
VBS Supply Characteristics
VBSUV+
VBS Supply Undervoltage
Positive Going Threshold
VBSUVVBS Supply Undervoltage
Negative Going Threshold
VBSUVHYS
VBS Supply Undervoltage
Lockout Hysteresis
tdUVBS
Undervoltage Lockout
Response Time
IQBS1
VBS Supply Current
IQBS2
VBS
†
†
4.3
VCC rising from 0V
2.8
VCC dropping from 5V
V
0.02
0.3
0.5
0.60
20
sec
400
uA
5.4
VCC steps either from 6.5V to 2.7V
or from 2.7V to 6.5V
VCC = 3.6V & 6.5V
VBS rising from 0V
V
3.9
0.02
VBS dropping from 5V
0.3
0.60
20
sec
130
A
VBS Supply Current
300
A
VBS Drop Due to Output
Turn-On
210
mV
0.5
VBS steps either from 6.5V to 2.7V
or from 2.7V to 6.5V
static mode, VBS = 7V, IN = 0V or
5V
static mode, VBS = 16V, IN = 0V or
5V
VBS = 7V, CBS = 1F, td_Igen-IN =
3sec, tTEST = 100sec, No load
See also Fig. 4 and 5
3
www.irf.com
© 2014 International Rectifier
Submit Datasheet Feedback
December 10, 2014
AUIRS20162S
Electrical Characteristics
Unless otherwise specified, VCC = 5V, VBS = 7V, VS = 0V, IN = 0V, RES = 5V, load R = 50, C = 2.5nF. Unless
otherwise noted, these specifications apply for an operating junction temperature range of -40C Tj 125C.
Symbol
Definition
Min
Typ
Max Units
Test Conditions
Gate Driver Characteristics
IPKSo1
Peak Output Source Current
120
IPKSo2
Peak Output Source Current
70
IPKSo3
Peak Output Source Current
250
IPKSo4
Peak Output Source Current
150
tr1
Output Rise Time
tr2
Output Rise Time
tr3
Output Rise Time
tr4
Output Rise Time
IPKSi1
Peak Output Sink Current
120
IPKSi2
Peak Output Sink Current
70
IPKSi3
Peak Output Sink Current
250
IPKSi4
Peak Output Sink Current
150
tf1
Output Fall Time
tf2
Output Fall Time
tf3
Output Fall Time
250
mA
mA
500
0.2
0.1
††
VBS = 16V, Tj = 25C
mA
VBS = 16V
0.4
sec
Tj = 25C
0.5
sec
0.2
sec
VBS = 16V, Tj = 25C
0.3
sec
VBS = 16V
††
††
††
mA
IN = 5V, Tj = 25C
mA
IN = 5V,
mA
VBS = 16V, IN = 5V, Tj = 25C
mA
VBS = 16V, IN = 5V
0.4
sec
IN = 5V, Tj = 25C
0.5
sec
IN = 5V
0.2
sec
VBS = 16V, IN = 5V, Tj = 25C
500
0.1
††
mA
250
0.2
Tj = 25C,
††
††
††
Output Fall Time
0.3
sec VBS = 16V, IN = 5V
tplh
Input-to-Output Turn-On
0.15
0.35
sec
Propagation Delay (50% input
level to 10% output level)
tphl
Input-to-Output Turn-Off
0.15
0.35
sec
Propagation Delay (50% input
level to 90% output level)
tphl_res
RES-to-Output Turn-Off
0.15
0.35
sec
Propagation Delay (50%
input level to 90% [tphl]
output levels)
tplh_res
RES-to-Output Turn-On
0.15
0.35
sec
Propagation Delay (50%
input level to 10% [tplh]
output levels)
††
:Peak Output Sink and Source Current tests are performed with the output shorted and therefore highly
dissipative. Therefore, it is not recommended that this test be performed for longer than 10usec at a time.
tf4
4
www.irf.com
© 2014 International Rectifier
Submit Datasheet Feedback
December 10, 2014
AUIRS20162S
Electrical Characteristics
Unless otherwise specified, VCC = 5V, VBS = 7V, VS = 0V, IN = 0V, RES = 5V, load R = 50, C = 2.5nF. Unless
otherwise noted, these specifications apply for an operating junction temperature range of -40C Tj 125C.
Symbol
Definition
Min
Typ
Max
Units
Test Conditions
Input Characteristics
VINH
High Logic Level Input
Threshold
VINL
Low Logic Level Input
Threshold
RIN
IN pull up Input Resistance
IIN
VH_RES
VL_RES
RRES
IRES
High Logic Level Input
Current
High Logic Level RES Input
Threshold
Low Logic Level RES Input
Threshold
RES pull down Input
Resistance
Low Logic Level Input
Current
Recharge Characteristics
ton_rech
Recharge Transistor TurnOn Propagation Delay
toff_rech
Recharge Transistor TurnOff Propagation Delay
VRECH
Recharge Output Transistor
On-State Voltage Drop
Deadtime Characteristics
DTHOFF
High Side Turn-Off to
Recharge gate Turn-On
DTHON
Recharge gate Turn-Off to
High Side Turn-On
5
www.irf.com
0.66*
Vcc
60
100
3
VCC=5V
V
VCC=5V
0.28*
Vcc
220
k
5
A
VIN= VCC
V
VCC =5V
V
VCC =5V
0.66*
Vcc
60
V
0.28*
Vcc
220
k
5
A
VRES=0
6
9
sec
VS = 5V
0.08
0.24
sec
1.2
V
IS = 1mA, IN = 5V.
100
3
6
9
sec
VCC = 5V, VBS = 7V
0.005
0.07
0.4
sec
VCC = 5V, VBS = 7V
© 2014 International Rectifier
Submit Datasheet Feedback
December 10, 2014
AUIRS20162S
Functional Block Diagram
6
www.irf.com
© 2014 International Rectifier
Submit Datasheet Feedback
December 10, 2014
AUIRS20162S
Input/Output Pin Equivalent Circuit Diagrams
VCC
VB
ESD
Diode
ESD
Diode
INRESD
HO
ESD
Diode
ESD
Diode
GND
VS
VCC
ESD
Diode
RESETRESD
ESD
Diode
GND
GND
VB
VCC
VB
20V
20V
166V
GND
VS
GND
7
www.irf.com
© 2014 International Rectifier
Submit Datasheet Feedback
December 10, 2014
AUIRS20162S
Lead Definitions
Pin Number
Symbol
Pin description
1
VCC
Driver Supply, typically 5.0V
2
IN-
Driver Control Signal Input (negative logic)
3
GND
4
RESET-
5
VS
MOSFET Source Connection
6
NC
No Connection (no Bond-wire)
7
HO
MOSFET Gate Connection
8
VB
Driver Output Stage Supply
Ground
Driver Enable Signal Input (negative logic)
Lead Assignments
1
VCC
VB
8
2
IN-
HO
7
3
GND
NC
6
4
RESET-
VS
5
8 Lead SOIC
8
www.irf.com
© 2014 International Rectifier
Submit Datasheet Feedback
December 10, 2014
AUIRS20162S
Application Information and Additional Details
The AUIRS20162S is a high voltage power MOSFET and IGBT high side driver with internal VS-to-GND
recharge NMOS. Proprietary HVIC and latch immune CMOS technologies enable ruggedized monolithic
construction. The logic input is compatible with standard 5V CMOS or LSTTL logic. The output driver
features a 250mA high pulse current buffer stage. The channel can be used to drive an N-channel power
MOSFET or IGBT in the high side configuration, which operates up to 150 volts above GND ground.
A Truth table for Vcc, VBS, RESET, IN, HO and RechFET is shown as follows.
This table is valid for voltages ranges defined in the recommended operating conditions section.
Supply voltages and
thresholds
Signals
Output
Ho
Recharge Path
Vcc
VBS
RESET-
IN-
< VCCUV-
X
X
X
OFF
ON
> VCCUV+
X
LOW
X
OFF
ON
> VCCUV+
X
X
HIGH
OFF
ON
> VCCUV+
> VBSUV+
HIGH
LOW
ON
OFF
> VCCUV+
< VBSUV-
HIGH
LOW
OFF
OFF
Table 1: logic operation
Recharge Path = ON indicates that the recharge MOSFET is on.
Recharge Path = OFF indicates that the recharge MOSFET is off.
In the case that Vcc will be removed during operation, Ho will be turned off if the resulting
dVcc/dt is slow enough to allow UVLO response time as defined in the tdUVCC parameter.
If Ho was low it will remain low.
9
www.irf.com
© 2014 International Rectifier
Submit Datasheet Feedback
December 10, 2014
AUIRS20162S
Timing Diagrams and Additional Information
Input / Output
IN
RES
90%
90%
HO
t plh
10%
t phl
10%
tr
OFF
Recharge
tf
ON
t off_ rech
t on_ rech
Figure 1: Input/Output Timing Diagram
Reset
IN
RES
HO
t plh_res
t phl_res
Figure 2: Reset Timing Diagram
Start-up
IN
RES
(logic 0, pull down to GND)
(logic 1, pull up to Vcc)
HO
VccUVLO
VCC
2.7V
tdUVCC
VbsUV
VBS
tdUVBS
Figure 3: Start up Diagram
10
www.irf.com
© 2014 International Rectifier
Submit Datasheet Feedback
December 10, 2014
AUIRS20162S
VB Drop Voltage Test
Figure 4: Vbs drop Voltage test
Vbs voltage drop due to the high
side
section activation at no load
Figure 5: Vbs drop Voltage waveforms
11
www.irf.com
© 2014 International Rectifier
Submit Datasheet Feedback
December 10, 2014
AUIRS20162S
Performance Graphs
RESET Functionality Graph:
VBS (V)
RESET Functionality Graph
25
23
21
19
17
15
13
11
9
7
5
3.2
3.4
3.6
3.8
4.0
4.2 4.4
4.6
4.8
5.0
5.2
VCC (V)
25C
-40C
125C
Figure 6-1
Figure 6. RESET Functionality:
This graph explains the functionality limitation as a function of VCC, VBS and temperature.
For each particular temperature and VCC, the output is non-functional for any value of VBS above the drawn
curve. But for any value of VBS below the curve the functionality is fine.
RESET Functional Diagram:
IN-
RESET -
HO-VS
Figure 6-2
12
www.irf.com
© 2014 International Rectifier
Submit Datasheet Feedback
December 10, 2014
AUIRS20162S
Parameter Temperature Trends
Figures illustrated in this chapter provide information on the experimental performance of the AUIRS20162S
HVIC. The line plotted in each figure is generated from actual lab data. A large number of individual samples were
tested at three temperatures (-40 ºC, 25 ºC, and 125 ºC) in order to generate the experimental curve. The line
consists of three data points (one data point at each of the tested temperatures) that have been connected
together to illustrate the understood trend. The individual data points on the Typ. curve were determined by
calculating the averaged experimental value of the parameter (for a given temperature).
Input and Reset Thresholds:
Vinth+ vs Vcc supply
3.8
3.6
3.4
3.2
(V)
3
2.8
2.6
2.4
2.2
-40C
27C
125C
2
5
6.5
Vcc (V)
Figure 7-1: Positive Input and Reset Threshold Voltage Distribution Curves
Vinth- vs Vcc supply
3
2.8
2.6
(V)
2.4
2.2
2
1.8
-40C
27C
125C
1.6
5
Vcc (V)
6.5
Figure 7-2: Negative Input and Reset Threshold Voltage Distribution Curves
13
www.irf.com
© 2014 International Rectifier
Submit Datasheet Feedback
December 10, 2014
AUIRS20162S
VBUV Undervoltage Shutdown Threshold VB:
4.70
4.65
4.60
4.55
4.50
4.45
4.40
4.35
4.30
4.25
4.20
-50
-25
0
25
-3std
50
75
Mean
100
125
150
+3std
Figure 8-1: Negative going VBSUV- value vs. Temperature:
5.10
5.00
4.90
4.80
4.70
4.60
4.50
4.40
-50
-25
0
25
-3Std
50
Mean
75
100
125
150
+3Std
Figure 8-2: Positive going VBSUV+ Value vs. Temperature
14
www.irf.com
© 2014 International Rectifier
Submit Datasheet Feedback
December 10, 2014
AUIRS20162S
Input and Reset impedance
Input and Reset Impedance
200
180
160
140
120
100
80
60
40
20
0
-42
-22
-2
18
38
Mean
58
+3Std
78
98
118
-3Std
Figure 9: Input and Reset Impedance Distribution Curves vs. Temperature
Recharge FET I-V Curve
V_RECH FET I-V Curve
2.5
I_current (mA)
2
1.5
1
0.5
-40C
27C
125C
0
0.6
0.7
0.8
0.9
1
1.1
1.2
1.3
1.4
V_RECH (V)
Figure 10: Recharge FET IV-Curve
15
www.irf.com
© 2014 International Rectifier
Submit Datasheet Feedback
December 10, 2014
AUIRS20162S
Package Details: SOIC8
16
www.irf.com
© 2014 International Rectifier
Submit Datasheet Feedback
December 10, 2014
AUIRS20162S
Tape and Reel Details: SOIC8
LOADED TAPE FEED DIRECTION
A
B
H
D
F
C
NOTE : CONTROLLING
DIMENSION IN MM
E
G
CARRIER TAPE DIMENSION FOR 8SOICN
Metric
Imperial
Code
Min
Max
Min
Max
A
7.90
8.10
0.311
0.318
B
3.90
4.10
0.153
0.161
C
11.70
12.30
0.46
0.484
D
5.45
5.55
0.214
0.218
E
6.30
6.50
0.248
0.255
F
5.10
5.30
0.200
0.208
G
1.50
n/a
0.059
n/a
H
1.50
1.60
0.059
0.062
F
D
B
C
A
E
G
H
REEL DIMENSIONS FOR 8SOICN
Metric
Code
Min
Max
A
329.60
330.25
B
20.95
21.45
C
12.80
13.20
D
1.95
2.45
E
98.00
102.00
F
n/a
18.40
G
14.50
17.10
H
12.40
14.40
17
www.irf.com
Imperial
Min
Max
12.976
13.001
0.824
0.844
0.503
0.519
0.767
0.096
3.858
4.015
n/a
0.724
0.570
0.673
0.488
0.566
© 2014 International Rectifier
Submit Datasheet Feedback
December 10, 2014
AUIRS20162S
Part Marking Information
Part number
AS20162
Date code
AYWW ?
Pin 1
Identifier
? XXXX
?
MARKING CODE
P
Lead Free Released
Non-Lead Free Released
18
www.irf.com
IR logo
© 2014 International Rectifier
Lot Code
(Prod mode –
4 digit SPN code)
Assembly site code
Per SCOP 200-002
Submit Datasheet Feedback
December 10, 2014
AUIRS20162S
Qualification Information
(Note1)
Automotive
(per AEC-Q100)
Qualification Level
Comments: This family of ICs has passed an Automotive
qualification. IR’s Industrial and Consumer qualification level
is granted by extension of the higher Automotive level.
Moisture Sensitivity Level
Machine Model
Human Body Model
ESD
Charged Device Model
IC Latch-Up Test
RoHS Compliant
Note 1
Note 2
19
SOIC8N
MSL3 260°C (Note2)
(per IPC/JEDEC J-STD-020)
Class M1 (Pass +/-200 V)
(per AEC-Q100-003)
Class H1C (+/-2000V)
(per AEC-Q100-002)
Class C4 (Pass +/-1000V)
(per AEC-Q100-011)
Class II, Level A
(per AEC-Q100-004)
Yes
Qualification standards can be found at International Rectifier’s web site http://www.irf.com/
Higher MSL ratings may be available for the specific package types listed here. Please contact your
International Rectifier sales representative for further information.
www.irf.com
© 2014 International Rectifier
Submit Datasheet Feedback
December 10, 2014
AUIRS20162S
IMPORTANT NOTICE
Unless specifically designated for the automotive market, International Rectifier Corporation and its subsidiaries (IR) reserve
the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at
any time and to discontinue any product or services without notice. Part numbers designated with the “AU” prefix follow
automotive industry and / or customer specific requirements with regards to product discontinuance and process change
notification. All products are sold subject to IR’s terms and conditions of sale supplied at the time of order acknowledgment.
IR warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with IR’s
standard warranty. Testing and other quality control techniques are used to the extent IR deems necessary to support this
warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily
performed.
IR assumes no liability for applications assistance or customer product design. Customers are responsible for their products
and applications using IR components. To minimize the risks with customer products and applications, customers should
provide adequate design and operating safeguards.
Reproduction of IR information in IR data books or data sheets is permissible only if reproduction is without alteration and is
accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with
alterations is an unfair and deceptive business practice. IR is not responsible or liable for such altered documentation.
Information of third parties may be subject to additional restrictions.
Resale of IR products or serviced with statements different from or beyond the parameters stated by IR for that product or
service voids all express and any implied warranties for the associated IR product or service and is an unfair and deceptive
business practice. IR is not responsible or liable for any such statements.
IR products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the
body, or in other applications intended to support or sustain life, or in any other application in which the failure of the I R
product could create a situation where personal injury or death may occur. Should Buyer purchase or use IR products for any
such unintended or unauthorized application, Buyer shall indemnify and hold International Rectifier and its officers,
employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and
reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such
unintended or unauthorized use, even if such claim alleges that IR was negligent regarding the design or manufacture of the
product.
IR products are neither designed nor intended for use in military/aerospace applications or environments unless the IR
products are specifically designated by IR as military-grade or “enhanced plastic.” Only products designated by IR as
military-grade meet military specifications. Buyers acknowledge and agree that any such use of IR products which IR has not
designated as military-grade is solely at the Buyer’s risk, and that they are solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
IR products are neither designed nor intended for use in automotive applications or environments unless the specific IR
products are designated by IR as compliant with ISO/TS 16949 requirements and bear a part number including the
designation “AU”. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications,
IR will not be responsible for any failure to meet such requirements.
For technical support, please contact IR’s Technical Assistance Center
http://www.irf.com/technical-info/
WORLD HEADQUARTERS:
101 N. Sepulveda Blvd., El Segundo, California 90245
Tel: (310) 252-7105
20
www.irf.com
© 2014 International Rectifier
Submit Datasheet Feedback
December 10, 2014
工商网监
湘ICP备2023018690号
