BGF119E6329XTSA1

D a t a S he et , V 3. 0 , N o v e m be r 2 00 8 B G F 11 9 T r a n s i e n t V o l t ag e S u p p r es s o r S m a l l S i g n a l D i s c r et e s Edition 2008-11-18 Published by Infineon Technologies AG 81726 München, Germany © Infineon Technologies AG 2008. All Rights Reserved. Legal Disclaimer The information given in this document shall in no event be regarded as a guarantee of conditions or characteristics (“Beschaffenheitsgarantie”). With respect to any examples or hints given herein, any typical values stated herein and/or any information regarding the application of the device, Infineon Technologies hereby disclaims any and all warranties and liabilities of any kind, including without limitation warranties of non-infringement of intellectual property rights of any third party. Information For further information on technology, delivery terms and conditions and prices please contact your nearest Infineon Technologies Office (www.infineon.com). Warnings Due to technical requirements components may contain dangerous substances. For information on the types in question please contact your nearest Infineon Technologies Office. Infineon Technologies Components may only be used in life-support devices or systems with the express written approval of Infineon Technologies, if a failure of such components can reasonably be expected to cause the failure of that life-support device or system, or to affect the safety or effectiveness of that device or system. Life support devices or systems are intended to be implanted in the human body, or to support and/or maintain and sustain and/or protect human life. If they fail, it is reasonable to assume that the health of the user or other persons may be endangered. BGF119 BGF119 Revision History: 2008-11-18, V3.0 Previous Version: 2008-10-20, V2.0 Page Subjects (major changes since last revision) 6 Updated Figure 3 All Target status removed Data Sheet 3 V3.0, 2008-11-18 BGF119 Transient Voltage Suppressor Transient Voltage Suppressor Features • 1 channel TVS diode designed for portable application • ESD protection according to IEC61000-4-2 for +/-15 kV contact discharge on all IOs • Wafer Level Package with SnAgCu solder balls • RoHS and WEEE compliant package • Very small form factor TVS • High peak pulse power • Stand-off voltage up to 8 V • Low clamping voltage factor Vcl/Vbr • Fast response time WLP-4-1-3D Description The BGF119 is a single line TVS diode designed for transient voltage and power overstress suppression. All pins are protected against ESD pulses of 15kV contact discharge according to IEC61000-4-2. The wafer level package is a green package with a size of only 0.75 mm x 0.75 mm and a total height of 0.60 mm. Type BGF119 Data Sheet Package WLP-4-1 Marking Chip BGF119 N0742 4 V3.0, 2008-11-18 BGF119 Transient Voltage Suppressor Table 1 Maximum Ratings Parameter Symbol Values Min. VP Operating temperature range TOP Storage temperature range TSTG Electrostatic discharge according to IEC61000- VESD Voltage at all pins to GND Typ. Unit Max. 0 8 V -30 +85 °C -55 +150 °C -15 15 kV Note / Test Condition 4-21) at all pins 1) Contact discharge Table 2 Electrical Characteristics1) Parameter Symbol Values Min. CT VF2) VBR Line capacitance to GND Forward voltage Break down voltage Leakage current of line to GND Unit Note / Test Condition pF VR = 0 V IF = 850 mA IR = 15 mA TA= -30°C TA= 25°C TA= 85°C IR = 1 A VR = 8 V TA= -30°C TA= 25°C TA= 85°C Max. 230 1.1 V V 10 Clamping voltage during transient Typ. 10 11 12 VCL3) IR 12 13 V nA 1 10 100 800 1) Otherwise specified at TA = 25 °C 2) To avoid high temperature and possible disassembling of component from the board, DC current operation to be limited to few seconds 3) 8/20 µs pulse waveform according to IEC61000-4-5 A1 A2 B1 (GND) Figure 1 Data Sheet B2 (GND) Schematic 5 V3.0, 2008-11-18 BGF119 Transient Voltage Suppressor Line Capacitance BGF119 Line Capacitance [pF] 300 250 200 150 100 50 0 0 1 2 3 4 5 6 Voltage [V] Figure 2 Line capacitance versus reverse voltage (typical values) at 25°C BGF119 Peak pulse current vs clamping voltage Reverse Current I R [A] 100,0 10,0 1,0 0,1 10 12 14 16 18 20 Clamping Voltage VCL [V] Figure 3 Data Sheet Peak pulse reverse current (IEC61000-4-5) versus clamping voltage (typical values) at 25°C 6 V3.0, 2008-11-18 BGF119 Transient Voltage Suppressor Package Outline 0.75 ±0.05 4x ø0.05 M A B C A1 B2 B1 0.25 ±0.04 1) 0.08 C 4x COPLANARITY A 0.75 ±0.05 A2 (0.175 ±0.05 ) (0.175 ±0.05 ) (0.175 ±0.05 ) SEATING PLANE 3) (0.175 ±0.05 ) 0.1 C 0.4 0.2 ±0.05 STANDOFF Pin A1 Corner Index Area 2) B 0.4 0.6 ±0.05 1) Dimension is measured at the maximum solder ball diameter, parallel to primary datum C 2) A1 corner identified by marking 3) Primary datum C and seating plane are defined by the domed crowns of the balls WLP-4-1-PO-N V02 Figure 4 Package WLP-4-1 Tape and reel specification 4 ±0.1 Pin 1 Corner Index Area Figure 5 Data Sheet 8 ±0.1 0.85 ±0.05 0.25 0.85 ±0.05 0.65 WLP-4-1-TP V01 Tape for WLP-4-1 7 V3.0, 2008-11-18