Please note that Cypress is an Infineon Technologies Company.
The document following this cover page is marked as “Cypress” document as this is the
company that originally developed the product. Please note that Infineon will continue
to offer the product to new and existing customers as part of the Infineon product
portfolio.
Continuity of document content
The fact that Infineon offers the following product as part of the Infineon product
portfolio does not lead to any changes to this document. Future revisions will occur
when appropriate, and any changes will be set out on the document history page.
Continuity of ordering part numbers
Infineon continues to support existing part numbers. Please continue to use the
ordering part numbers listed in the datasheet for ordering.
www.infineon.com
CY14ME064J2
64-Kbit (8 K × 8) Serial (I2C) nvSRAM
with Extended temperature
64-Kbit (8 K × 8) Serial (I2C) nvSRAM with Extended temperature
Features
64 Kb nonvolatile static random access memory (nvSRAM)
❐ Internally organized as 8 K × 8
❐ STORE to QuantumTrap nonvolatile elements initiated
automatically on power-down (AutoStore) or by using I2C
command (Software STORE)
❐ RECALL to SRAM initiated on power-up (Power-Up
RECALL) or by I2C command (Software RECALL)
❐ Automatic STORE on power-down with a small capacitor
■ High reliability
❐ Infinite read, write, and RECALL cycles
❐ STORE cycles to QuantumTrap
• 1,000 K cycles at 85 C
• 200 K cycles at 105 C
❐ Data retention
• 20 years at 85 C
• 10 years at 105 C
■
Low power consumption
❐ Average active current of 2 mA at 3.4 MHz operation
❐ Average standby mode current of 250 µA
❐ Sleep mode current of 20 µA
■
Industry standard configurations
❐ Operating voltages:
• CY14ME064J2: VCC = 4.5 V to 5.5 V
❐ Extended temperature: –40 C to +105 C
❐ 8- pin small outline integrated circuit (SOIC) package
❐ Restriction of hazardous substances (RoHS) compliant
■
High speed I2C interface
❐ Industry standard 100 kHz and 400 kHz speed
❐ Fast-mode Plus: 1 MHz speed
❐ High speed: 3.4 MHz
❐ Zero cycle delay reads and writes
■ Write protection
❐ Hardware protection using Write Protect (WP) pin
❐ Software block protection for 1/4, 1/2, or entire array
2
■ I C access to special functions
❐ Nonvolatile STORE/RECALL
❐ 8 byte serial number
❐ Manufacturer ID and Product ID
❐ Sleep mode
■
Overview
The Cypress CY14MB064J/CY14ME064J2 combines a 64-Kbit
nvSRAM[1] with a nonvolatile element in each memory cell. The
memory is organized as 8 K words of 8 bits each. The embedded
nonvolatile elements incorporate the QuantumTrap technology,
creating the world’s most reliable nonvolatile memory. The
SRAM provides infinite read and write cycles, while the
QuantumTrap cells provide highly reliable nonvolatile storage of
data. Data transfers from SRAM to the nonvolatile elements
(STORE operation) takes place automatically at power-down.
On power-up, data is restored to the SRAM from the nonvolatile
memory (RECALL operation). The STORE and RECALL
operations can also be initiated by the user through I2C
commands.
Logic Block Diagram
Serial Number
8x8
VCC VCAP
Manufacture ID/
Product ID
Power Control
Block
Memory Control Register
Quantrum Trap
8Kx8
Command Register
Sleep
SDA
SCL
A2, A1
WP
2
Control Registers Slave
I C Control Logic
Slave Address
Decoder
Memory Slave
Memory
Address and Data
Control
SRAM
8Kx8
STORE
RECALL
Note
1. Serial (I2C) nvSRAM is referred to as nvSRAM throughout the datasheet.
Cypress Semiconductor Corporation
Document Number: 001- 73680 Rev. *A
•
198 Champion Court
•
San Jose, CA 95134-1709
•
408-943-2600
Revised December 18, 2012
CY14ME064J2
Contents
Pinouts .............................................................................. 3
Pin Definitions .................................................................. 3
I2C Interface ...................................................................... 4
Protocol Overview ............................................................ 4
I2C Protocol – Data Transfer ....................................... 4
Data Validity ................................................................ 5
High Speed Mode (Hs-mode) ...................................... 6
Slave Device Address ................................................. 7
Write Protection (WP) .................................................. 9
AutoStore Operation .................................................... 9
Hardware RECALL (Power-Up) .................................. 9
Write Operation ......................................................... 10
Read Operation ......................................................... 10
Memory Slave Access .................................................... 10
Write nvSRAM ........................................................... 10
Current nvSRAM Read .............................................. 12
Random Address Read ............................................. 13
Control Registers Slave ................................................. 14
Write Control Registers ............................................. 14
Current Control Registers Read ................................ 15
Random Control Registers Read .............................. 15
Serial Number ................................................................. 16
Serial Number Write .................................................. 16
Serial Number Lock ................................................... 16
Serial Number Read .................................................. 16
Device ID ......................................................................... 17
Executing Commands Using Command Register ..... 17
Document Number: 001- 73680 Rev. *A
Maximum Ratings ........................................................... 18
Operating Range ............................................................. 18
DC Electrical Characteristics ........................................ 18
Data Retention and Endurance ..................................... 19
Thermal Resistance ........................................................ 19
AC Test Loads and Waveforms ..................................... 20
AC Test Conditions ........................................................ 20
AC Switching Characteristics ....................................... 21
Switching Waveforms .................................................... 21
nvSRAM Specifications ................................................. 22
Switching Waveforms .................................................... 22
Software Controlled STORE/RECALL Cycles .............. 23
Switching Waveforms .................................................... 23
Ordering Information ...................................................... 24
Ordering Code Definitions ......................................... 24
Package Diagrams .......................................................... 25
Acronyms ........................................................................ 26
Document Conventions ................................................. 26
Units of Measure ....................................................... 26
Document History Page ................................................. 27
Sales, Solutions, and Legal Information ...................... 28
Worldwide Sales and Design Support ....................... 28
Products .................................................................... 28
PSoC Solutions ......................................................... 28
Page 2 of 28
CY14ME064J2
Pinouts
Figure 1. 8-pin SOIC pinout
VCAP
1
A1
2
A2
3
VSS
4
CY14ME064J2
Top View
not to scale
8
VCC
7
WP
6
SCL
5
SDA
Pin Definitions
Pin Name
I/O Type
SCL
Input
SDA
Description
Clock. Runs at speeds up to a maximum of fSCL.
Input/Output I/O. Input/Output of data through I2C interface.
Output: Is open-drain and requires an external pull-up resistor.
WP
Input
Write Protect. Protects the memory from all writes. This pin is internally pulled LOW and hence can be
left open if not connected.
A2–A1
Input
Slave Address. Defines the slave address for I2C. This pin is internally pulled LOW and hence can be
left open if not connected.
VCAP
Power supply AutoStore Capacitor. Supplies power to the nvSRAM during power loss to STORE data from the SRAM
to nonvolatile elements. If not required, AutoStore must be disabled and this pin left as no connect. It
must never be connected to ground.
VSS
Power supply Ground
VCC
Power supply Power supply
Document Number: 001- 73680 Rev. *A
Page 3 of 28
CY14ME064J2
I2C Interface
I2C bus consists of two lines – serial clock line (SCL) and serial
data line (SDA) that carry information between multiple devices
on the bus. I2C supports multi-master and multi-slave
configurations. The data is transmitted from the transmitter to the
receiver on the SDA line and is synchronized with the clock SCL
generated by the master.
The SCL and SDA lines are open-drain lines and are pulled up
to VCC using resistors. The choice of pull-up resistor on the
system depends on the bus capacitance and the intended speed
of operation. The master generates the clock and all the data
I/Os are transmitted in synchronization with this clock. The
CY14ME064J2 supports up to 3.4 MHz clock speed on SCL line.
Protocol Overview
This device supports only a 7-bit addressable scheme. The
master generates a START condition to initiate the
communication followed by broadcasting a slave select byte.
The slave select byte consists of a seven bit address of the slave
that the master intends to communicate with and R/W bit
indicating a read or a write operation. The selected slave
responds to this with an acknowledgement (ACK). After a slave
is selected, the remaining part of the communication takes place
between the master and the selected slave device. The other
devices on the bus ignore the signals on the SDA line till a STOP
or Repeated START condition is detected. The data transfer is
done between the master and the selected slave device through
the SDA pin synchronized with the SCL clock generated by the
master.
I2C Protocol – Data Transfer
Each transaction in I2C protocol starts with the master
generating a START condition on the bus, followed by a seven
bit slave address and eighth bit (R/W) indicating a read (1) or a
write (0) operation. All signals are transmitted on the open-drain
SDA line and are synchronized with the clock on SCL line. Each
byte of data transmitted on the I2C bus is acknowledged by the
receiver by holding the SDA line LOW on the ninth clock pulse.
The request for write by the master is followed by the memory
address and data bytes on the SDA line. The writes can be
performed in burst-mode by sending multiple bytes of data. The
memory address increments automatically after receiving
/transmitting of each byte on the falling edge of 9th clock cycle.
The new address is latched just prior to sending/receiving the
acknowledgment bit. This allows the next sequential byte to be
accessed with no additional addressing. On reaching the last
memory location, the address rolls back to 0x0000 and writes
continue. The slave responds to each byte sent by the master
during a write operation with an ACK. A write sequence can be
terminated by the master generating a STOP or Repeated
START condition.
A read request is performed at the current address location
(address next to the last location accessed for read or write). The
memory slave device responds to a read request by transmitting
the data on the current address location to the master. A random
address read may also be performed by first sending a write
request with the intended address of read. The master must
abort the write immediately after the last address byte and issue
a Repeated START or STOP signal to prevent any write
operation. The following read operation starts from this address.
The master acknowledges the receipt of one byte of data by
holding the SDA pin LOW for the ninth clock pulse. The reads
can be terminated by the master sending a no-acknowledge
(NACK) signal on the SDA line after the last data byte. The
no-acknowledge signal causes the CY14ME064J2 to release the
SDA line and the master can then generate a STOP or a
Repeated START condition to initiate a new operation.
Figure 2. System Configuration using Serial (I2C) nvSRAM
Vcc
RPmax = tr / (0.8473 * Cb)
RPmin = (VCC - VOLmax) / IOL
SDA
Microcontroller
SCL
Vcc
SCL
A1
SDA
A2
WP
CY14ME064J2
#0
Document Number: 001- 73680 Rev. *A
SCL
A1
SDA
A2
WP
CY14ME064J2
#3
Page 4 of 28
CY14ME064J2
Data Validity
STOP Condition (P)
The data on the SDA line must be stable during the HIGH period
of the clock. The state of the data line can only change when the
clock on the SCL line is LOW for the data to be valid. There are
only two conditions under which the SDA line may change state
with SCL line held HIGH, that is, START and STOP condition.
The START and STOP conditions are generated by the master
to signal the beginning and end of a communication sequence
on the I2C bus.
A LOW to HIGH transition on the SDA line while SCL is HIGH
indicates a STOP condition. This condition indicates the end of
the ongoing transaction.
START and STOP conditions are always generated by the
master. The bus is considered to be busy after the START
condition. The bus is considered to be free again after the STOP
condition.
Repeated START (Sr)
START Condition (S)
A HIGH to LOW transition on the SDA line while SCL is HIGH
indicates a START condition. Every transaction in I2C begins
with the master generating a START condition.
If an Repeated START condition is generated instead of a STOP
condition the bus continues to be busy. The ongoing transaction
on the I2C lines is stopped and the bus waits for the master to
send a slave ID for communication to restart.
Figure 3. START and STOP Conditions
full pagewidth
SDA
SDA
SCL
SCL
S
P
STOP Condition
START Condition
Figure 4. Data Transfer on the I2C Bus
handbook, full pagewidth
P
SDA
Acknowledgement
signal from slave
MSB
SCL
S
or
Sr
1
2
START or
Repeated START
condition
7
8
9
ACK
Byte complete,
interrupt within slave
Byte Format
Each operation in I2C is done using 8 bit words. The bits are sent
in MSB first format on SDA line and each byte is followed by an
ACK signal by the receiver.
An operation continues till a NACK is sent by the receiver or
STOP or Repeated START condition is generated by the master
The SDA line must remain stable when the clock (SCL) is HIGH
except for a START or STOP condition.
Acknowledge / No-acknowledge
After transmitting one byte of data or address, the transmitter
releases the SDA line. The receiver pulls the SDA line LOW to
acknowledge the receipt of the byte. Every byte of data
transferred on the I2C bus needs to be responded with an ACK
signal by the receiver to continue the operation. Failing to do so
is considered as a NACK state. NACK is the state where receiver
Document Number: 001- 73680 Rev. *A
Acknowledgement
signal from receiver
1
2
3-8
9
ACK
Clock line held LOW while
interrupts are serviced
Sr
Sr
or
P
STOP or
Repeated START
condition
does not acknowledge the receipt of data and the operation is
aborted.
NACK can be generated by master during a READ operation in
following cases:
The master did not receive valid data due to noise
The master generates a NACK to abort the READ sequence.
After a NACK is issued by the master, nvSRAM slave releases
control of the SDA pin and the master is free to generate a
Repeated START or STOP condition.
NACK can be generated by nvSRAM slave during a WRITE
operation in following cases:
nvSRAM did not receive valid data due to noise.
The master tries to access write protected locations on the
nvSRAM. Master must restart the communication by
generating a STOP or Repeated START condition.
Page 5 of 28
CY14ME064J2
Figure 5. Acknowledge on the I2C Bus
handbook, full pagewidth
DATA OUTPUT
BY MASTER
not acknowledge (A)
DATA OUTPUT
BY SLAVE
acknowledge (A)
SCL FROM
MASTER
1
2
8
9
S
clock pulse for
acknowledgement
START
condition
High Speed Mode (Hs-mode)
Serial Data Format in Hs-mode
In Hs-mode, nvSRAM can transfer data at bit rates of up to
3.4 Mbit/s. A master code (0000 1XXXb) must be issued to place
the device into high speed mode. This enables master/slave
communication for speed upto 3.4 MHz. A stop condition exits
Hs-mode.
Serial data transfer format in Hs-mode meets the standard-mode
I2C-bus specification. Hs-mode can only commence after the
following conditions (all of which are in F/S-modes):
1. START condition (S)
2. 8-bit master code (0000 1XXXb)
3. No-acknowledge bit (A)
Figure 6. Data transfer format in Hs-mode
handbook, full pagewidth
Hs-mode
F/S-mode
S
MASTER CODE
A Sr SLAVE ADD. R/W A
F/S-mode
DATA
n (bytes+ ack.)
A/A P
Hs-mode continues
Sr SLAVE ADD.
Single and multiple-byte reads and writes are supported. After
the device enters into Hs-mode, data transfer continues in
Hs-mode until stop condition is sent by master device. The slave
switches back to F/S-mode after a STOP condition (P). To
Document Number: 001- 73680 Rev. *A
continue data transfer in Hs-mode, the master sends Repeated
START (Sr).
See Figure 12 on page 11 and Figure 15 on page 12 for Hs-mode
timings for read and write operation.
Page 6 of 28
CY14ME064J2
Slave Device Address
2
Every slave device on an I C bus has a device select address.
The first byte after START condition contains the slave device
address with which the master intends to communicate. The
seven MSBs are the device address and the LSB (R/W bit) is
used for indicating Read or Write operation. The CY14ME064J2
reserves two sets of upper 4 MSBs [7:4] in the slave device
address field for accessing Memory and Control Registers. The
accessing mechanism is described in Memory Slave Device on
page 7.
The nvSRAM product provides two different functionalities:
Memory and Control Registers functions (such as serial number
and product ID). The two functions of the device are accessed
through different slave device addresses. The first four most
significant bits [7:4] in the device address register are used to
select between the nvSRAM functions.
Table 1. Slave device Addressing
Bit 7
Bit 6
Bit 5
Bit 4
1
0
1
0
Bit 3
Bit 2
Bit 1
Device Select ID
nvSRAM
Bit 0 Function
Select
CY14ME064J2 Slave Devices
R/W Selects Memory
Memory, 8 K × 8
Control Registers
- Memory Control Register, 1 × 8
0
0
1
1
Device Select ID
R/W
- Serial Number, 8 × 8
Selects Control
Registers
- Device ID, 4 × 8
- Command Register, 1 × 8
Memory Slave Device
Control Registers Slave Device
The nvSRAM device is selected for Read/Write if the master
issues the slave address as 1010b followed by two bits of device
select. For CY14MX064J2 device select is two bits with third bit
don’t care. If slave address sent by the master matches with the
Memory Slave device address then depending on the R/W bit of
the slave address, data is either read from (R/W = ‘1’) or written
to (R/W = ’0’) the nvSRAM.
The Control Registers Slave device includes the Serial Number,
Product ID, Memory Control and Command Register.
The address length for CY14ME064J2 is 13 bits and thus it
requires 2 address bytes to map the entire memory address
location. The dedicated two address bytes represent bit A0 to
A12. However, since the address is only 13-bits, it implies that
the first three MSB bits that is fed in is ignored by the device.
Although these bits are ‘don’t care’, Cypress recommends that
this bit is treated as 0 to enable seamless transition to higher
memory densities.
Figure 7. Memory Slave Device Address
MSB
handbook, halfpage
1
The nvSRAM Control Register Slave device is selected for
Read/Write if the master issues the Slave address as 0011b
followed by two bits of device select. For CY14MX064J2 device
select is two bits with third bit don’t care. If the slave address sent
by the master matches with the Memory Slave device address
then depending on the R/W bit of the slave address, data is either
read from (R/W = ‘1’) or written to (R/W = ‘0’) the nvSRAM.
Figure 8. Control Registers Slave Device Address
MSB
handbook, halfpage
0
LSB
0
1
Slave ID
1
A2
A1
X
R/W
Device Select
LSB
0
1
Slave ID
0
A2
A1
X
R/W
Device Select
Document Number: 001- 73680 Rev. *A
Page 7 of 28
CY14ME064J2
Command Register
Table 2. Control Registers map
Address
0x00
0x01
0x02
0x03
0x04
0x05
0x06
0x07
0x08
0x09
0x0A
0x0B
0x0C
0x0D
0xAA
Description
Memory
Control
Register
Serial Number
8 Bytes
Read/Write
Details
Read/Write Contains
Block
Protect Bits and Serial
Number Lock bit
Read/Write Programmable Serial
(Read only Number. Locked by
when SNL setting the Serial
is set)
Number lock bit in the
Memory
Control
Register to ‘1’.
Device ID
Read only Device ID is factory
programmed
Reserved
Command
Register
Reserved Reserved
Write only Allows commands for
STORE,
RECALL,
AutoStore
Enable/Disable,
SLEEP Mode
Memory Control Register
The Command Register resides at address “AA” of the Control
Registers Slave device. This is a write only register. The byte
written to this register initiates a STORE, RECALL, AutoStore
Enable, AutoStore Disable and sleep mode operation as listed in
Table 5. Refer to Serial Number on page 16 for details on how to
execute a command register byte.
Table 5. Command Register bytes
■
Bit 5
0
Bit 4
0
Bit 3
BP1
(0)
Bit 2
BP0
(0)
Bit 1
0
BP1:BP0
00
01
10
11
Block Protection
None
0x1800–0x1FFF
0x1000–0x1FFF
0x0000–0x1FFF
SNL (S/N Lock) Bit: Serial Number Lock bit (SNL) is used to lock
the serial number. Once the bit is set to ‘1’, the serial number
registers are locked and no modification is allowed. This bit
cannot be cleared to ‘0’. The serial number is secured on the next
STORE operation (Software STORE or AutoStore). If AutoStore
is not enabled, user must perform the Software STORE
operation to secure the lock bit status. If a STORE was not
performed, the serial number lock bit will not survive the power
cycle. The default value shipped from the factory for SNL is ‘0’.
Document Number: 001- 73680 Rev. *A
0110 0000
RECALL
0101 1001
0001 1001
1011 1001
ASENB
ASDISB
SLEEP
STORE SRAM data to nonvolatile
memory
RECALL data from nonvolatile
memory to SRAM
Enable AutoStore
Disable AutoStore
Enter Sleep Mode for low power
consumption
RECALL: Initiates nvSRAM Software RECALL. The nvSRAM
cannot be accessed for tRECALL time after this instruction has
been executed. The RECALL operation does not alter the data
in the nonvolatile elements. A RECALL may be initiated in two
ways: Hardware RECALL, initiated on power-up; and Software
RECALL, initiated by a I2C RECALL instruction.
■
ASENB: Enables nvSRAM AutoStore. The nvSRAM cannot be
accessed for tSS time after this instruction has been executed.
This setting is not nonvolatile and needs to be followed by a
manual STORE sequence if this is desired to survive power
cycle. The part comes from the factory with AutoStore Enabled
and 0x00 written in all cells.
■
ASDISB: Disables nvSRAM AutoStore. The nvSRAM cannot
be accessed for tSS time after this instruction has been
executed. This setting is not nonvolatile and needs to be
followed by a manual STORE sequence if this is desired to
survive the power cycle.
Table 4. Block Protection
Level
0
1/4
1/2
1
STORE
■
Bit 0
0
BP1:BP0: Block Protect bits are used to protect 1/4, 1/2 or full
memory array. These bits can be written through a write
instruction to the 0x00 location of the Control Register Slave
device. However, any STORE cycle causes transfer of SRAM
data into a nonvolatile cell regardless of whether or not the
block is protected. The default value shipped from the factory
for BP0 and BP1 is ‘0’.
Description
STORE: Initiates nvSRAM Software STORE. The nvSRAM
cannot be accessed for tSTORE time after this instruction has
been executed. When initiated, the device performs a STORE
operation regardless of whether a write has been performed
since the last NV operation. After the tSTORE cycle time is
completed, the SRAM is activated again for read/write
operations.
Table 3. Memory Control Register Bits
Bit 6
SNL
(0)
Command
■
The Memory Control Register contains the following bits:
Bit 7
0
Data Byte
[7:0]
0011 1100
Note If AutoStore is disabled and VCAP is not required, it is
required that the VCAP pin is left open. VCAP pin must never be
connected to ground. Power-Up RECALL operation cannot be
disabled in any case.
■
SLEEP: SLEEP instruction puts the nvSRAM in a sleep mode.
When the SLEEP instruction is registered, the nvSRAM takes
tSS time to process the SLEEP request. Once the SLEEP
command is successfully registered and processed, the
nvSRAM performs a STORE operation to secure the data to
nonvolatile memory and then enters into SLEEP mode.
Whenever nvSRAM enters into sleep mode, it initiates non
volatile STORE cycle which results in losing an endurance
cycle per sleep command execution. A STORE cycle starts only
if a write to the SRAM has been performed since the last
STORE or RECALL cycle.
Page 8 of 28
CY14ME064J2
The nvSRAM enters into sleep mode as follows:
1. The Master sends a START command
2. The Master sends Control Registers Slave device ID with I2C
Write bit set (R/W = ‘0’)
3. The Slave (nvSRAM) sends an ACK back to the Master
4. The Master sends Command Register address (0xAA)
5. The Slave (nvSRAM) sends an ACK back to the Master
6. The Master sends Command Register byte for entering into
Sleep mode
7. The Slave (nvSRAM) sends an ACK back to the Master
8. The Master generates a STOP condition.
Once in Sleep mode the device starts consuming IZZ current
tSLEEP time after SLEEP instruction is registered. The device is
not accessible for normal operations until it is out of sleep mode.
The nvSRAM wakes up after tWAKE duration after the device
slave address is transmitted by the master.
Transmitting any of the two slave addresses wakes the nvSRAM
from Sleep mode. The nvSRAM device is not accessible during
tSLEEP and tWAKE interval, and any attempt to access the
nvSRAM device by the master is ignored and nvSRAM sends
NACK to the master. As an alternative method of determining
when the device is ready, the master can send read or write
commands and look for an ACK.
the device inhibits all memory accesses to nvSRAM and
automatically performs a conditional STORE operation using the
charge from the VCAP capacitor. The AutoStore operation is not
initiated if no write cycle has been performed since the last
STORE or RECALL.
Note If a capacitor is not connected to VCAP pin, AutoStore must
be disabled by issuing the AutoStore Disable instruction
specified in Command Register on page 8. If AutoStore is
enabled without a capacitor on VCAP pin, the device attempts an
AutoStore operation without sufficient charge to complete the
Store. This will corrupt the data stored in nvSRAM as well as the
serial number and it will unlock the SNL bit.
Figure 9 shows the proper connection of the storage capacitor
(VCAP) for AutoStore operation. Refer to DC Electrical
Characteristics on page 18 for the size of the VCAP.
Figure 9. AutoStore Mode
VCC
0.1 uF
VCC
VCAP
Write Protection (WP)
The WP pin is an active high pin and protects entire memory and
all registers from write operations. To inhibit all the write
operations, this pin must be held high. When this pin is high, all
memory and register writes are prohibited and address counter
is not incremented. This pin is internally pulled LOW and hence
can be left open if not used.
VSS
VCAP
AutoStore Operation
Hardware RECALL (Power-Up)
The AutoStore operation is a unique feature of nvSRAM which
automatically stores the SRAM data to QuantumTrap cells
during power-down. This STORE makes use of an external
capacitor (VCAP) and enables the device to safely STORE the
data in the nonvolatile memory when power goes down.
During power-up, when VCC crosses VSWITCH, an automatic
RECALL sequence is initiated which transfers the content of
nonvolatile memory on to the SRAM. The data would previously
have been stored on the nonvolatile memory through a STORE
sequence.
During normal operation, the device draws current from VCC to
charge the capacitor connected to the VCAP pin. When the
voltage on the VCC pin drops below VSWITCH during power-down,
A Power-Up RECALL cycle takes tFA time to complete and the
memory access is disabled during this time.
Document Number: 001- 73680 Rev. *A
Page 9 of 28
CY14ME064J2
Write Operation
The last bit of the slave device address indicates a read or a write
operation. In case of a write operation, the slave device address
is followed by the memory or register address and data. A write
operation continues as long as a STOP or Repeated START
condition is generated by the master or if a NACK is issued by
the nvSRAM.
A NACK is issued from the nvSRAM under the following
conditions:
1. A valid Device ID is not received.
2. A write (burst write) access to a protected memory block
address returns a NACK from nvSRAM after the data byte is
received. However, the address counter is set to this address
and the following current read operation starts from this
address.
3. A write/random read access to an invalid or out-of-bound
memory address returns a NACK from the nvSRAM after the
address is received. The address counter remains unchanged
in such a case.
After a NACK is sent out from the nvSRAM, the write operation
is terminated and any data on the SDA line is ignored till a STOP
or a Repeated START condition is generated by the master.
immediately after the slave device address byte is sent out by
the master. The read operation starts from the current address
location (the location following the previous successful write or
read operation). When the last address is reached, the address
counter loops back to the first address.
In case of the Control Register Slave, whenever a burst read is
performed such that it flows to a non-existent address, the reads
operation will loop back to 0x00. This is applicable, in particular
for the Command Register.
There are the following ways to end a read operation:
1. The Master issues a NACK on the 9th clock cycle followed by
a STOP or a Repeated START condition on the 10th clock
cycle.
2. Master generates a STOP or Repeated START condition on
the 9th clock cycle.
More details on write instruction are provided in the section
Memory Slave Access on page 10.
Memory Slave Access
The following sections describe the data transfer sequence
required to perform Read or Write operations from nvSRAM.
For example, consider a case where the burst write access is
performed on Control Register Slave address 0x01 for writing the
serial number and continued to the address 0x09, which is a read
only register. The device returns a NACK and address counter
will not be incremented. A following read operation will be started
from the address 0x09. Further, any write operation which starts
from a write protected address (say, 0x09) will be responded by
the nvSRAM with a NACK after the data byte is sent and set the
address counter to this address. A following read operation will
start from the address 0x09 in this case also.
Write nvSRAM
Note In case the user tries to read/write access an address that
does not exist (for example 0x0D in Control Register Slave),
nvSRAM responds with a NACK immediately after the
out-of-bound address is transmitted. The address counter
remains unchanged and holds the previous successful read or
write operation address.
A write operation is executed only after all the 8 data bits have
been received by the nvSRAM. The nvSRAM sends an ACK
signal after a successful write operation. A write operation may
be terminated by the master by generating a STOP condition or
a Repeated START operation. If the master desires to abort the
current write operation without altering the memory contents, this
should be done using a START/STOP condition prior to the 8th
data bit.
A write operation is performed internally with no delay after the
eighth bit of data is transmitted. If a write operation is not
intended, the master must terminate the write operation before
the eighth clock cycle by generating a STOP or Repeated
START condition.
More details on write instruction are provided in the section
Memory Slave Access on page 10.
Read Operation
Each write operation consists of a slave address being
transmitted after the start condition. The last bit of slave address
must be set as ‘0’ to indicate a Write operation. The master may
write one byte of data or continue writing multiple consecutive
address locations while the internal address counter keeps
incrementing automatically. The address register is reset to
0x0000 after the last address in memory is accessed. The write
operation continues till a STOP or Repeated START condition is
generated by the master or a NACK is issued by the nvSRAM.
If the master tries to access a write protected memory address
on the nvSRAM, a NACK is returned after the data byte intended
to write the protected address is transmitted and address counter
will not be incremented. Similarly, in a burst mode write
operation, a NACK is returned when the data byte that attempts
to write a protected memory location and address counter will not
be incremented.
If the last bit of the slave device address is ‘1’, a read operation
is assumed and the nvSRAM takes control of the SDA line
Document Number: 001- 73680 Rev. *A
Page 10 of 28
CY14ME064J2
Figure 10. Single-Byte Write into nvSRAM (except Hs-mode)
By Master
SDA Line
S
T
A
R
T
Most Significant Address Byte
Memory Slave Address
S
1
0
1
0 A2 A1 X
X
0
X
Least Significant Address Byte
S
T
0
P
Data Byte
P
X
By nvSRAM
A
A
A
A
Figure 11. Multi-Byte Write into nvSRAM (except Hs-mode)
SDA Line
S
1
0
1
0 A2 A1
X
Least Significant Address
Byte
Most Significant Address
Byte
0
X
X
S
T
0
P
Data Byte N
Data Byte 1
~
~
By Master
S
T
A
R Memory Slave Address
T
X
P
By nvSRAM
A
A
A
A
A
Figure 12. Single-Byte Write into nvSRAM (Hs-mode)
By Master
SDA Line
S
T
A
R
T
Hs-mode command
S 0 0 0
0 1
Most Significant Address
Byte
Memory Slave Address
X X X
Sr 1 0
1 0 A2 A1 X 0
Least Significant Address
Byte
S
T
0
P
Data Byte
P
X X X
By nvSRAM
A
A
A
A
A
Figure 13. Multi-Byte Write into nvSRAM (Hs-mode)
SDA Line
Hs-mode command
S 0 0 0
0 1
Most Significant Address
Byte
Memory Slave Address
X X X
Sr 1 0
1 0 A2 A1 X 0
Least Significant Address
Byte
Data Byte 1
~
~
By Master
S
T
A
R
T
X X X
By nvSRAM
A
By Master
A
By nvSRAM
~
~
SDA Line
A
Document Number: 001- 73680 Rev. *A
A
A
S
T
0
P
Data Byte N
Data Byte 3
Data Byte 2
A
A
P
A
Page 11 of 28
CY14ME064J2
Current nvSRAM Read
terminate a read operation after reading 1 byte or continue
reading addresses sequentially till the last address in the
memory after which the address counter rolls back to the
address 0x0000. The valid methods of terminating read access
are described in Section Read Operation on page 10.
Each read operation starts with the master transmitting the
nvSRAM slave address with the LSB set to ‘1’ to indicate “Read”.
The reads start from the address on the address counter. The
address counter is set to the address location next to the last
accessed with a “Write” or “Read” operation. The master may
Figure 14. Current Location Single-Byte nvSRAM Read (except Hs-mode)
S
T
A
R
T
By Master
SDA Line
S
A
Memory Slave Address
1
0
1
A2 A1 X
0
S
T
0
P
P
1
By nvSRAM
Data Byte
A
Figure 15. Current Location Multi-Byte nvSRAM Read (except Hs-mode)
SDA Line
A
A
Memory Slave Address
S
1
0
1
0 A2 A1 X
1
By nvSRAM
S
T
0
P
P
~
~
By Master
S
T
A
R
T
Data Byte N
Data Byte
A
Figure 16. Current Location Single-Byte nvSRAM Read (Hs-mode)
S
T
A
R
T
By Master
SDA Line
Hs-mode command
S 0 0 0
0 1
S
A T
0
P
Memory Slave Address
X X X
Sr 1 0
P
1 0 A2 A1 X 1
By nvSRAM
A
A
Data Byte
Figure 17. Current Location Multi-Byte nvSRAM Read (Hs-mode)
SDA Line
A
Hs-mode command
S 0 0 0
0 1
X X X
Sr 1 0
1 0 A2 A1 X 1
Data Byte
By nvSRAM
A
Document Number: 001- 73680 Rev. *A
A
Memory Slave Address
~
~
By Master
S
T
A
R
T
S
T
0
P
P
Data Byte N
A
Page 12 of 28
CY14ME064J2
Random Address Read
A random address read is performed by first initiating a write
operation and generating a Repeated START immediately after
the last address byte is acknowledged. The address counter is
set to this address and the next read access to this slave will
initiate read operation from here. The master may terminate a
read operation after reading 1 byte or continue reading
addresses sequentially till the last address in the memory after
which the address counter rolls back to the start address 0x0000.
Figure 18. Random Address Single-Byte Read (except Hs-mode)
S
T
A
R
T
By Master
SDA Line
Memory Slave Address
S
1
1
0
0 A2 A1
X
Least Significant Address
Byte
Most Significant Address
Byte
X
X
0
A
Memory Slave Address
0
Sr 1
X
1
0 A2 A1
X
S
T
0
P
P
1
By nvSRAM
Data Byte
A
A
A
A
Figure 19. Random Address Multi-Byte Read (except Hs-mode)
SDA Line
S
1
0
1
0 A2 A1 X
Least Significant Address
Byte
Most Significant Address
Byte
Memory Slave Address
X
0
X
A
Memory Slave Address
Sr 1
X
0
1
0 A2 A1
X
~
~
By Master
S
T
A
R
T
1
By nvSRAM
Data Byte 1
A
A
S
T
0
P
A
A
A
P
Data Byte N
Figure 20. Random Address Single-Byte Read (Hs-mode)
SDA Line
Hs-mode command
S 0 0 0
0 1
Most Significant Address
Byte
Memory Slave Address
X X X
Sr 1 0
1 0 A2 A1 X 0
Least Significant Address
Byte
Memory Slave Address
Sr 1 0
X X X
1 0 A2 A1 X
1
~
~
By Master
S
T
A
R
T
By nvSRAM
A
A
A
A
A
S
T
A 0
P
P
Data Byte
Document Number: 001- 73680 Rev. *A
Page 13 of 28
CY14ME064J2
Figure 21. Random Address Multi-Byte Read (Hs-mode)
SDA Line
Hs-mode command
S 0 0 0
X X X
0 1
Most Significant Address
Byte
Memory Slave Address
Sr 1 0
1 0 A2 A1 X 0
Least Significant Address
Byte
Memory Slave Address
Sr 1 0
X X X
1 0 A2 A1 X 1
~
~
By Master
S
T
A
R
T
By nvSRAM
A
A
A
A
S
T
0
P
P
~
~
Data Byte
A
A
A
Data Byte N
Control Registers Slave
The following sections describes the data transfer sequence
required to perform Read or Write operations from Control
Registers Slave.
Write Control Registers
To write the Control Registers Slave, the master transmits the
Control Registers Slave address after generating the START
condition. The write sequence continues from the address
location specified by the master till the master generates a STOP
condition or the last writable address location.
If a non writable address location is accessed for write operation
during a normal write or a burst, the slave generates a NACK
after the data byte is sent and the write sequence terminates.
Any following data bytes are ignored and the address counter is
not incremented.
If a write operation is performed on the Command Register
(0xAA), the following current read operation also begins from the
first address (0x00) as in this case, the current address is an
out-of-bound address. The address is not incremented and the
next current read operation begins from this address location. If
a write operation is attempted on an out-of-bound address
location, the nvSRAM sends a NACK immediately after the
address byte is sent.
Further, if the serial number is locked, only two addresses (0xAA
or Command Register, and 0x00 or Memory Control Register)
are writable in the Control Registers Slave. On a write operation
to any other address location, the device will acknowledge
command byte and address bytes but it returns a NACK from the
Control Registers Slave for data bytes. In this case, the address
will not be incremented and a current read will happen from the
last acknowledged address.
The nvSRAM Control Registers Slave sends a NACK when an
out of bound memory address is accessed for write operation, by
the master. In such a case, a following current read operation
begins from the last acknowledged address.
Figure 22. Single-Byte Write into Control Registers
S
T
A
R
T
By Master
SDA Line
S
Control Registers
Slave Address
0
0
1
1 A2 A1 X
Control Register Address
S
T
0
P
Data Byte
P
0
By nvSRAM
A
A
A
Figure 23. Multi-Byte Write into Control Registers
SDA Line
S
Control Registers
Slave Address
0
0
1
1 A2 A1 X
Control Register Address
Data Byte
0
By nvSRAM
A
Document Number: 001- 73680 Rev. *A
S
T
0
P
Data Byte N
P
~
~
By Master
S
T
A
R
T
A
A
A
Page 14 of 28
CY14ME064J2
Current Control Registers Read
address location and loops back to the first location (0x00). Note
that the Command Register is a write only register and is not
accessible through the sequential read operations. If a burst read
operation begins from the Command Register (0xAA), the
address counter wraps around to the first address in the register
map (0x00).
A read of Control Registers Slave is started with master sending
the Control Registers Slave address after the START condition
with the LSB set to ‘1’. The reads begin from the current address
which is the next address to the last accessed location. The
reads to Control Registers Slave continues till the last readable
Figure 24. Control Registers Single-Byte Read
S
T
A
R
T
By Master
SDA Line
S
Control Registers
Slave Address
0
0
1
1 A2 A1
A
X
S
T
0
P
P
1
By nvSRAM
Data Byte
A
Figure 25. Current Control Registers Multi-Byte Read
S
T
A
R
T
SDA Line
S
0
0
1
A
A
1 A2 A1 X
1
By nvSRAM
Data Byte
S
T
0
P
P
~
~
By Master
Control Registers
Slave Address
Data Byte N
A
Random Control Registers Read
A read of random address may be performed by initiating a write
operation to the intended location of read and immediately
following with a Repeated START operation. The reads to
Control Registers Slave continues till the last readable address
location and loops back to the first location (0x00). Note that the
Command Register is a write only register and is not accessible
through the sequential read operations. A random read starting
at the Command Register (0xAA) loops back to the first address
in the Control Registers map (0x00). If a random read operation
is initiated from an out-of-bound memory address, the nvSRAM
sends a NACK after the address byte is sent.
.
Figure 26. Random Control Registers Single-Byte Read
By Master
SDA Line
S
T
A
R
T
S
Control Registers
Slave Address
0
0
1
1 A2 A1 X
Control Register Address
A
Control Registers Slave Address
Sr 0
0
0
1
1
A2 A1 X
S
T
0
P
P
1
By nvSRAM
Data Byte
A
Document Number: 001- 73680 Rev. *A
A
A
Page 15 of 28
CY14ME064J2
Figure 27. Random Control Registers Multi-Byte Read
SDA Line
S
Control Registers
Slave Address
0
0
1
1 A2 A1
Control Register Address
X
A
Control Registers Slave Address
Sr 0
0
0
1
1
A2 A1 X
1
~
~
By Master
S
T
A
R
T
By nvSRAM
Data Byte
A
A
A
A
S
T
0
P
P
Data Byte N
Serial Number
Serial number is an 8 byte memory space provided to the user
to uniquely identify this device. It typically consists of a two byte
customer ID, followed by five bytes of unique serial number and
one byte of CRC check. However, nvSRAM does not calculate
the CRC and it is up to the user to utilize the eight byte memory
space in the desired format. The default values for the eight byte
locations are set to ‘0x00’.
Serial Number Write
The serial number can be accessed through the Control
Registers Slave Device. To write the serial number, master
transmits the Control Registers Slave address after the START
condition and writes to the address location from 0x01 to 0x08.
The content of Serial Number registers is secured to nonvolatile
memory on the next STORE operation. If AutoStore is enabled,
nvSRAM automatically stores the Serial number in the
nonvolatile memory on power-down. However, if AutoStore is
disabled, user must perform a STORE operation to secure the
contents of Serial Number registers.
Note If the serial number lock (SNL) bit is not set, the serial
number registers can be re-written regardless of whether or not
a STORE has happened. Once the serial number lock bit is set,
no writes to the serial number registers are allowed. If the master
tries to perform a write operation to the serial number registers
Document Number: 001- 73680 Rev. *A
when the lock bit is set, a NACK is returned and write will not be
performed.
Serial Number Lock
After writes to Serial Number registers is complete, master is
responsible for locking the serial number by setting the serial
number lock bit to ‘1’ in the Memory Control Register (0x00). The
content of Memory Control Register and serial number are
secured on the next STORE operation (STORE or AutoStore). If
AutoStore is not enabled, user must perform STORE operation
to secure the lock bit status.
If a STORE was not performed, the serial number lock bit will not
survive power cycle. The serial number lock bit and 8-byte serial
number is defaults to ‘0’ at power-up.
Serial Number Read
Serial number can be read back by a read operation of the
intended address of the Control Registers Slave. The Control
Registers Device loops back from the last address (excluding the
Command Register) to 0x00 address location while performing
burst read operation. The serial number resides in the locations
from 0x01 to 0x08. Even if the serial number is not locked, a
serial number read operation will return the current values written
to the serial number registers. Master may perform a serial
number read operation to confirm if the correct serial number is
written to the registers before setting the lock bit.
Page 16 of 28
CY14ME064J2
Device ID
Device ID is a 4 byte code consisting of JEDEC assigned manufacturer ID, product ID, density ID, and die revision. These registers
are set in factory and are read only registers for the user.
Table 6. Device ID
Device
Device ID
(4 bytes)
CY14ME064J2
0x0681B088
Device ID Description
20–7
6–3
(14 bits)
(4 bits)
Product ID
Density ID
00001101100001
0001
31–21
(11 bits)
Manufacture ID
00000110100
2–0
(3 bits)
Die Rev
000
The device ID is divided into four parts as shown in Table 6:
4. Die Rev (3 bits)
1. Manufacturer ID (11 bits)
This is used to represent any major change in the design of the
product. The initial setting of this is always 0x0.
This is the JEDEC assigned manufacturer ID for Cypress.
JEDEC assigns the manufacturer ID in different banks. The first
three bits of the manufacturer ID represent the bank in which ID
is assigned. The next eight bits represent the manufacturer ID.
Executing Commands Using Command Register
The Control Registers Slave allows different commands to be
executed by writing the specific command byte in the Command
Register (0xAA). The command byte codes for each command
are specified in Table 5 on page 8. During the execution of these
commands the device is not accessible and returns a NACK if
any of the three slave devices is selected. If an invalid command
is sent by the master, the nvSRAM responds with an ACK
indicating that the command has been acknowledged with NOP
(No Operation). The address will rollover to 0x00 location.
Cypress manufacturer ID is 0x34 in bank 0. Therefore the
manufacturer ID for all Cypress nvSRAM products is given as:
Cypress ID - 000_0011_0100
2. Product ID (14 bits)
The product ID for device is shown in the Table 6.
3. Density ID (4 bits)
The 4-bit density ID is used as shown in Table 6 for indicating the
64-Kb density of the product.
Figure 28. Command Execution using Command Register
By Master
SDA Line
S
T
A
R
T
S
Control Register
Slave Address
0
0
1
1 A2 A1 X
Command Register Address
1
0
0
1
0
1
0
1
S
T
O
P
Command Byte
P
0
By nvSRAM
A
Document Number: 001- 73680 Rev. *A
A
A
Page 17 of 28
CY14ME064J2
Maximum Ratings
Exceeding maximum ratings may shorten the useful life of the
device. These user guidelines are not tested.
Storage temperature ................................ –65 C to +150 C
Maximum accumulated storage time
Transient voltage (< 20 ns) on
any pin to ground potential ................. –2.0 V to VCC + 2.0 V
Package power dissipation
capability (TA = 25 °C) ................................................. 1.0 W
Surface mount lead soldering
temperature (3 seconds) ......................................... +260 C
At 150 C ambient temperature ...................... 1000 h
DC output current (1 output at a time, 1 s duration). ... 15 mA
At 105 C ambient temperature .................. 10 Years
Static discharge voltage
(per MIL-STD-883, Method 3015) ......................... > 2001 V
At 85 C ambient temperature .................... 20 Years
Maximum junction temperature ................................. 150 C
Latch up current .................................................... > 140 mA
Supply voltage on VCC relative to VSS .........–0.5 V to +7.0 V
DC voltage applied to outputs
in High Z state .................................... –0.5 V to VCC + 0.5 V
Operating Range
Input voltage ....................................... –0.5 V to VCC + 0.5 V
Ambient Temperature
VCC
–40 C to +105 C
4.5 V to 5.5 V
DC Electrical Characteristics
Over the Operating Range
Parameter
Description
VCC
Power supply
ICC1
Average VCC current
Test Conditions
Min
Typ [2]
Max
Unit
4.5
5.0
5.5
V
fSCL = 3.4 MHz;
Values obtained without output loads
(IOUT = 0 mA)
–
–
2
mA
fSCL = 1 MHz;
Values obtained without output loads
(IOUT = 0 mA)
–
–
1
mA
ICC2
Average VCC current during
STORE
All inputs don’t care, VCC = Max
Average current for duration tSTORE
–
–
4
mA
ICC4
Average VCAP current during
AutoStore cycle
All inputs don't care. Average current
for duration tSTORE
–
–
4
mA
ISB
VCC standby current
SCL > (VCC – 0.2 V).
VIN < 0.2 V or > (VCC – 0.2 V).
Standby current level after nonvolatile
cycle is complete. Inputs are static.
fSCL = 0 MHz.
–
–
250
A
IZZ
Sleep mode current
tSLEEP time after SLEEP Instruction is
Issued. All inputs are static and
configured at CMOS logic level.
–
–
20
A
IIX[3]
Input current in each I/O pin
0.1 VCC < Vi < 0.9 VCC(max)
–5
–
+5
A
IOZ
Output leakage current
–5
–
+5
A
Ci
Capacitance for each I/O pin
–
–
7
pF
Capacitance measured across all input
and output signal pin and VSS.
Note
2. Typical values are at 25 °C, VCC = VCC(typ). Not 100% tested.
3. Not applicable to WP, A2 and A1 pins.
Document Number: 001- 73680 Rev. *A
Page 18 of 28
CY14ME064J2
DC Electrical Characteristics (continued)
Over the Operating Range
Parameter
Description
Test Conditions
Min
Typ [2]
Max
Unit
0.7 × Vcc
–
VCC + 0.5
V
VIH
Input HIGH voltage
VIL
Input LOW voltage
– 0.5
–
0.3 × Vcc
V
VOL
Output LOW voltage
IOL = 3 mA
0
–
0.4
V
Input resistance (WP, A2, A1)
For VIN = VIL (max)
50
–
–
k
For VIN = VIH (max)
1
–
–
M
0.05 × VCC
–
–
V
42
47
180
F
–
–
VCC– 0.5
V
Min
Unit
Data retention at 85 C
20
Years
Data retention at 105 C
10
Rin
[4]
Vhys
Hysteresis of Schmitt trigger
inputs
VCAP[5]
Storage capacitor
VVCAP[6,7]
Maximum voltage driven on VCAP VCC = Max
pin by the device
Between VCAP pin and VSS
Data Retention and Endurance
Parameter
DATAR
NVC
Description
Nonvolatile STORE operations 85 C
1,000
Nonvolatile STORE operations 105 C
200
K
Thermal Resistance
Parameter [7]
JA
JC
Description
Thermal resistance
(junction to ambient)
Thermal resistance
(junction to case)
Test Conditions
8-pin SOIC
Unit
Test conditions follow standard test methods and
procedures for measuring thermal impedance, per
EIA/JESD51.
101.08
C/W
37.86
C/W
Notes
4. The input pull-down circuit is stronger (50 K) when the input voltage is below VIL and weak (1 M) when the input voltage is above VIH.
5. Min VCAP value guarantees that there is a sufficient charge available to complete a successful AutoStore operation. Max VCAP value guarantees that the capacitor
on VCAP is charged to a minimum voltage during a Power-Up RECALL cycle so that an immediate power-down cycle can complete a successful AutoStore. Therefore
it is always recommended to use a capacitor within the specified min and max limits. Refer application note AN43593 for more details on VCAP options.
6. Maximum voltage on VCAP pin (VVCAP) is provided for guidance when choosing the VCAP capacitor. The voltage rating of the VCAP capacitor across the operating
temperature range should be higher than the VVCAP voltage.
7. These parameters are guaranteed by design and are not tested.
Document Number: 001- 73680 Rev. *A
Page 19 of 28
CY14ME064J2
AC Test Loads and Waveforms
Figure 29. AC Test Loads and Waveforms
5.0 V
1.6 K
OUTPUT
50 pF
AC Test Conditions
Description
Input pulse levels
Input rise and fall times (10%–90%)
Input and output timing reference levels
Document Number: 001- 73680 Rev. *A
CY14ME064J2
0 V to 5 V
10 ns
2.5 V
Page 20 of 28
CY14ME064J2
AC Switching Characteristics
Over the Operating Range
Parameter [8]
3.4 MHz [9]
Description
1 MHz [9]
400 kHz [9]
Unit
Min
Max
Min
Max
Min
Max
–
3400
–
1000
–
400
kHz
fSCL
Clock frequency, SCL
tSU; STA
Setup time for Repeated START
condition
160
–
250
–
600
–
ns
tHD;STA
Hold time for START condition
160
–
250
–
600
–
ns
tLOW
LOW period of the SCL
160
–
500
–
1300
–
ns
tHIGH
HIGH period of the SCL
60
–
260
–
600
–
ns
tSU;DATA
Data in setup time
10
–
100
–
100
–
ns
tHD;DATA
Data hold time (In/Out)
0
–
0
–
0
–
ns
tDH
Data out hold time
0
–
0
–
0
–
ns
[10]
Rise time of SDA and SCL
–
80
–
120
–
300
ns
tf[10]
Fall time of SDA and SCL
–
80
–
120
–
300
ns
tSU;STO
Setup time for STOP condition
160
–
250
–
600
–
ns
tVD;DATA
Data output valid time
–
130
–
400
–
900
ns
tVD;ACK
ACK output valid time
–
130
–
400
–
900
ns
tOF[10]
Output fall time from VIH min to
VILmax
–
80
–
120
–
300
ns
tBUF
Bus free time between STOP and
next START condition
0.3
–
0.5
–
1.3
–
us
tSP
Pulse width of spikes that must be
suppressed by input filter
–
10
–
50
–
50
ns
tr
Switching Waveforms
~
~
~
~
~
~
Figure 30. Timing Diagram
t SU;DATA
~
~
~
~
t HIGH
~
~
tr
t LOW
~
~
SDA
tf
t VD;DAT
t SP
t HD;STA
t VD;ACK
t BUF
t SU;STO
t HD;DATA
tf
t SU;STA
~
~
t HD;STA
~
~
SCL
S
Sr
START condition
Repeated START condition
tr
9th clock
(ACK)
P
S
STOP condition START condition
Notes
8. Test conditions assume signal transition time of 10 ns or less, timing reference levels of VCC/2, input pulse levels of 0 to VCC(typ), and output loading of the specified
IOL and load capacitance shown in Figure 29 on page 20.
9. Bus Load (Cb) Considerations; Cb < 500 pF for I2C clock frequency (SCL) 100/400/1000 kHz; Cb < 100 pF for SCL at 3.4 MHz.
10. These parameters are guaranteed by design and are not tested.
Document Number: 001- 73680 Rev. *A
Page 21 of 28
CY14ME064J2
nvSRAM Specifications
Over the Operating Range
Parameters
[11]
tFA
tSTORE [12]
tDELAY[13]
tVCCRISE[14]
VSWITCH
tWAKE
tSLEEP
tSB
Description
Min
–
–
–
150
–
–
–
–
Power-Up RECALL duration
STORE cycle duration
Time allowed to complete SRAM write cycle
VCC rise time
Low voltage trigger level
Time for nvSRAM to wake up from SLEEP mode
Time to enter low power mode after issuing SLEEP instruction
Time to enter into standby mode after issuing STOP condition
Max
20
8
25
–
4.40
20
8
100
Unit
ms
ms
ns
µs
V
ms
ms
µs
Switching Waveforms
Figure 31. AutoStore or Power-Up RECALL [15]
VCC
VSWITCH
12
t VCCRISE
Note
12
t STORE
Note
tSTORE
AutoStore
tDELAY
tDELAY
POWERUP
RECALL
tFA
tFA
Read & Write
Inhibited
(RWI)
POWER-UP
RECALL
Read & Write
BROWN
OUT
AutoStore
POWER-UP
RECALL
Read & Write
POWER
DOWN
AutoStore
Notes
11. tFA starts from the time VCC rises above VSWITCH.
12. If an SRAM write has not taken place since the last nonvolatile cycle, no AutoStore takes place.
13. On a AutoStore initiation, SRAM write operation continues to be enabled for time tDELAY.
14. These parameters are guaranteed by design and are not tested.
15. Read and Write cycles are ignored during STORE, RECALL, and while VCC is below VSWITCH.
Document Number: 001- 73680 Rev. *A
Page 22 of 28
CY14ME064J2
Software Controlled STORE/RECALL Cycles
Over the Operating Range
Parameter
CY14ME064J2
Description
Min
Max
Unit
tRECALL
RECALL duration
–
600
µs
tSS[16, 17]
Software sequence processing time
–
500
µs
Switching Waveforms
Figure 32. Software STORE/RECALL Cycle [17]
DATA OUTPUT
BY MASTER
Command Reg Address
nvSRAM Control Slave Address
acknowledge (A) by Slave
acknowledge (A) by Slave
SCL FROM
MASTER
1
2
8
9
1
Command Byte (STORE/RECALL)
2
8
9
1
acknowledge (A) by Slave
2
8
9
P
S
START
condition
RWI
t
STORE / t RECALL
Figure 33. AutoStore Enable/Disable Cycle
DATA OUTPUT
BY MASTER
Command Reg Address
nvSRAM Control Slave Address
acknowledge (A) by Slave
acknowledge (A) by Slave
SCL FROM
MASTER
1
2
8
9
1
Command Byte (ASENB/ASDISB)
2
8
9
1
acknowledge (A) by Slave
2
8
9
P
S
START
condition
RWI
t
SS
Notes
16. This is the amount of time it takes to take action on a soft sequence command. VCC power must remain HIGH to effectively register command.
17. Commands such as STORE and RECALL lock out I/O until operation is complete which further increases this time. See the specific command.
Document Number: 001- 73680 Rev. *A
Page 23 of 28
CY14ME064J2
Ordering Information
Ordering Code
Package Diagram
CY14ME064J2-SXQT
51-85066
Package Type
8-pin SOIC (with VCAP)
Operating Range
–40 to 105 °C
All these parts are Pb-free. This table contains Preliminary information. Contact your local Cypress sales representative for availability of these parts.
Ordering Code Definitions
CY 14 M B 064 J 2 - S X Q T
Option:
T - Tape and Reel
Blank - Std.
Temperature:
Q: –40 to 105 °C
Pb-free
Package:
S - 8-pin SOIC
2 - With VCAP
J - Serial (I2C) nvSRAM
Density:
Voltage:
E - 5.0 V
064 - 64 Kb
Metering
14 - nvSRAM
Cypress
Document Number: 001- 73680 Rev. *A
Page 24 of 28
CY14ME064J2
Package Diagrams
Figure 34. 8-pin SOIC (150 mils) Package Outline, 51-85066
51-85066 *E
Document Number: 001- 73680 Rev. *A
Page 25 of 28
CY14ME064J2
Acronyms
Acronym
Document Conventions
Description
Units of Measure
ACK
acknowledge
CMOS
complementary metal oxide semiconductor
%
percent
CRC
cyclic redundancy check
°C
degree Celsius
EIA
electronic industries alliance
I2C
kHz
kilohertz
inter-integrated circuit bus
K
kilohm
I/O
input/output
A
microampere
JEDEC
joint electron devices engineering council
mA
milliampere
LSB
least significant bit
F
microfarad
MSB
most significant bit
MHz
megahertz
nvSRAM
nonvolatile static random access memory
s
microsecond
NACK
no acknowledge
ms
millisecond
RWI
read and write inhibited
M
megaohm
RoHS
restriction of hazardous substances
ns
nanosecond
SNL
serial number lock
pF
picofarad
SCL
serial clock line
V
volt
SDA
serial data line
ohm
SOIC
small outline integrated circuit
W
watt
SRAM
static random access memory
WP
write protect
Document Number: 001- 73680 Rev. *A
Symbol
Unit of Measure
Page 26 of 28
CY14ME064J2
Document History Page
Document Title: CY14ME064J2, 64-Kbit (8 K x 8) Serial (I2C) nvSRAM with Extended Temperature
Document Number: 001-73680
Rev.
ECN No.
Orig. of
Change
Submission
Date
**
3472913
GVCH
12/28/2011
New data sheet.
*A
3843620
GVCH
12/18/2012
Changed status from “Preliminary” to “Final”.
Updated Maximum Ratings:
Removed “Ambient temperature with power applied” and included “Maximum
junction temperature”.
Updated DC Electrical Characteristics:
Added VVCAP parameter and its details, added Note 6 and referred the same
note in VVCAP parameter, also referred Note 7 in VVCAP parameter.
Updated Data Retention and Endurance:
Changed minimum value of DATAR parameter from 5 years to 10 years for
Data retention at 105 C temperature.
Document Number: 001- 73680 Rev. *A
Description of Change
Page 27 of 28
CY14ME064J2
Sales, Solutions, and Legal Information
Worldwide Sales and Design Support
Cypress maintains a worldwide network of offices, solution centers, manufacturer’s representatives, and distributors. To find the office
closest to you, visit us at Cypress Locations.
Products
Automotive
Clocks & Buffers
Interface
Lighting & Power Control
PSoC Solutions
cypress.com/go/automotive
cypress.com/go/clocks
psoc.cypress.com/solutions
cypress.com/go/interface
PSoC 1 | PSoC 3 | PSoC 5
cypress.com/go/powerpsoc
cypress.com/go/plc
Memory
Optical & Image Sensing
PSoC
Touch Sensing
USB Controllers
Wireless/RF
cypress.com/go/memory
cypress.com/go/image
cypress.com/go/psoc
cypress.com/go/touch
cypress.com/go/USB
cypress.com/go/wireless
© Cypress Semiconductor Corporation, 2010-2012. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use of
any circuitry other than circuitry embodied in a Cypress product. Nor does it convey or imply any license under patent or other rights. Cypress products are not warranted nor intended to be used for
medical, life support, life saving, critical control or safety applications, unless pursuant to an express written agreement with Cypress. Furthermore, Cypress does not authorize its products for use as
critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress products in life-support systems
application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges.
Any Source Code (software and/or firmware) is owned by Cypress Semiconductor Corporation (Cypress) and is protected by and subject to worldwide patent protection (United States and foreign),
United States copyright laws and international treaty provisions. Cypress hereby grants to licensee a personal, non-exclusive, non-transferable license to copy, use, modify, create derivative works of,
and compile the Cypress Source Code and derivative works for the sole purpose of creating custom software and or firmware in support of licensee product to be used only in conjunction with a Cypress
integrated circuit as specified in the applicable agreement. Any reproduction, modification, translation, compilation, or representation of this Source Code except as specified above is prohibited without
the express written permission of Cypress.
Disclaimer: CYPRESS MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS MATERIAL, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES
OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Cypress reserves the right to make changes without further notice to the materials described herein. Cypress does not
assume any liability arising out of the application or use of any product or circuit described herein. Cypress does not authorize its products for use as critical components in life-support systems where
a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress’ product in a life-support systems application implies that the manufacturer
assumes all risk of such use and in doing so indemnifies Cypress against all charges.
Use may be limited by and subject to the applicable Cypress software license agreement.
Document Number: 001- 73680 Rev. *A
Revised December 18, 2012
All products and company names mentioned in this document may be the trademarks of their respective holders.
Page 28 of 28
工商网监
湘ICP备2023018690号
