CYBLE-013025-00
CYBLE-013030-00
PRELIMINARY
EZ-BLE™ WICED Module
General Description
Power Consumption
The CYBLE-0130XX-00 is a fully integrated Bluetooth Low
Energy (BLE) wireless module solution. The CYBLE-0130XX-00
includes an onboard crystal oscillator, passive components, flash
memory, and the Cypress CYW20737 silicon device. Refer to the
CYW20737 datasheet for additional details on the capabilities of
the silicon device used in this module.
■
One-second interval average: 120 uA
■
Advertising Only Current (20-ms interval): 2.7 mA
■
Cypress CYW20737 silicon low-power mode support
❐ Sleep: 50-µA typical
❐ Deep Sleep (HIDOFF): 1.5-µA typical
The CYBLE-0130XX-00 supports peripheral functions (ADC and
PWM), as well as serial communication (UART, SPI, I2C). The
CYBLE-0130XX-00 includes a royalty-free BLE stack compatible
with Bluetooth 4.1 in a 14.5 × 19.2 × 2.25 mm package.
Functional Capabilities
■
10-bit auxiliary ADC with nine analog channels
■
Serial communications interface (compatible with Philips® I2C
slaves)
■
Serial peripheral interface (SPI) support for both master and
slave modes
■
Four dedicated PWM blocks
■
BLE protocol stack supporting generic access profile (GAP)
Central, Peripheral, Observer, or Broadcaster roles
The CYBLE-0130XX-00 is fully qualified by Bluetooth SIG and is
targeted at applications requiring cost-optimized BLE wireless
connectivity. The CYBLE-013025-00 is footprint compatible[1]
with the Cypress CYBLE-x120xx-00 module family.
■
Programmable output power from –20 dbm to +4 dBm (steps
of ± 4 dBm)
■
Quadrature Decoder
Module Description
Benefits
■
Module size: 14.52 mm × 19.20 mm × 2.25 mm
■
Bluetooth LE 4.1 listed single-mode module
❐ QDID: 96386
❐ Declaration ID: D035307
CYBLE-0130XX-00 provides all necessary components required
to operate BLE communication standards.
The CYBLE-013025-00 includes 128 KB of onboard serial flash
memory and is designed for standalone operation. The
CYBLE-013030-00 does not contain onboard flash, requiring an
external host to control the module via HCI commands or an
external host to perform a RAM upload procedure, where the
uploaded code will then execute from RAM. The
CYBLE-013030-00 can also interface to external flash on the
host board.
■
Certified to FCC, ISED, MIC, and CE regulations
■
Castelated solder pad connections for ease-of-use
■
128 KB on-module serial flash memory (CYBLE-013025-00)
■
60-KB SRAM memory
■
Up to 14 GPIOs
■
Temperature range: –30 °C to +85 °C
■
Cortex-M3 32-bit processor
■
Supports RSA encryption/decryption and key exchange
mechanisms (up to 4 kbit)
■
Maximum TX output power: +4.0 dbm
■
RX Receive Sensitivity: –94 dbm
■
Received signal strength indicator (RSSI) with 1-dB resolution
■
Proven hardware design ready to use
■
Cost optimized for applications without space constraints
■
Nonvolatile memory for self-sufficient operation
(CYBLE-013025-00 only)
■
Over-the-air update capable for in-field updates
(CYBLE-013025-00 only)
■
Bluetooth SIG qualified with QDID and Declaration ID
■
Fully certified module eliminates the time needed for design,
development, and certification processes
■
WICED™ SMART provides an easy-to-use integrated design
environment (IDE) to configure, develop, and program a BLE
application
■
Pre-programmed EZ-Serial firmware platform to allow for
easy-to-use out of the box Bluetooth Low Energy connectivity
Note
1. CYBLE-0130XX-00 global connections (Power, Ground, XRES, etc) are pad compatible with the CYBLE-x120xx-00 family of modules. Available GPIO and functions
may not be 100% compatible with your design. A review of the pad location and function within your design should be complete to determine if the CYBLE-013025-00
is completely pad-compatible to the CYBLE-x120xx-00 modules.
Cypress Semiconductor Corporation
Document Number: 002-19200 Rev. **
•
198 Champion Court
•
San Jose, CA 95134-1709
•
408-943-2600
Revised June 8, 2017
PRELIMINARY
CYBLE-013025-00
CYBLE-013030-00
More Information
Cypress provides a wealth of data at www.cypress.com to help you to select the right module for your design, and to help you to
quickly and effectively integrate the module into your design.
■
■
■
■
Overview: EZ-BLE Module Portfolio, Module Roadmap
EZ-BLE WICED Product Overview
CYW20737 BLE Silicon Datasheet
Knowledge Base Article
❐ KBA97095 - EZ-BLE™ Module Placement
❐ KBA213260 - RF Regulatory Certifications for CYBLE-013025-00 and CYBLE-013030-00 EZ-BLE™ WICED
Modules
❐ KBA213976 - FAQ for BLE and Regulatory Certifications with
EZ-BLE modules
❐ KBA210802 - Queries on BLE Qualification and Declaration
Processes
■
Development Kits:
❐ CYBLE-013025-EVAL, CYBLE-013025-00 Evaluation Board
■
Test and Debug Tools:
®
❐ CYSmart, Bluetooth LE Test and Debug Tool (Windows)
®
❐ CYSmart Mobile, Bluetooth LE Test and Debug Tool
(Android/iOS Mobile App)
Two Easy-To-Use Design Environments to Get You Started Quickly
Wireless Connectivity for Embedded Devices Smart (WICED Smart) Software Development Kit (SDK)
Cypress's WICED® Smart Version 2.2.3 (Wireless Connectivity for Embedded Devices) is a full-featured platform with proven Software
Development Kits (SDKs) and turnkey hardware solutions from partners to readily enable Wi-Fi and Bluetooth connectivity in system
design.
The WICED Smart SDK includes the tools and software needed to create BLE peripheral and central devices for a wide range of
products. The SDK is available as a standalone compressed file or as a separate installer bundled with the WICED Integrated
Development Environment.
EZ-Serial™ BLE Firmware Platform
The EZ-Serial Firmware Platform provides a simple way to access the most common hardware and communication features needed
in BLE applications. EZ-Serial implements an intuitive API protocol over the UART interface and exposes various status and control
signals through the module’s GPIOs, making it easy to add BLE functionality quickly to existing designs.
Use a simple serial terminal and evaluation kit to begin development without requiring an IDE.
EZ-BLE modules are pre-flashed with the EZ-Serial Firmware Platform. If you do not have EZ-Serial pre-loaded on your module, you
can download each EZ-BLE module’s firmware images on the EZ-Serial webpage.
Technical Support
■
Cypress Community: Whether you are a customer, partner, or a developer interested in the latest Cypress innovations, the Cypress
Developer Community offers you a place to learn, share, and engage with both Cypress experts and other embedded engineers
around the world.
■
Frequently Asked Questions (FAQs): Learn more about our BLE ECO System.
■
Visit our support page and create a technical support case or contact a local sales representatives. If you are in the United States,
you can talk to our technical support team by calling our toll-free number: +1-800-541-4736. Select option 2 at the prompt.
Document Number: 002-19200 Rev. **
Page 2 of 41
PRELIMINARY
CYBLE-013025-00
CYBLE-013030-00
Contents
Overview............................................................................ 4
Functional Block Diagram ........................................... 4
Module Description...................................................... 4
Pad Connection Interface ................................................ 6
Recommended Host PCB Layout ................................... 7
Module Connections ........................................................ 9
Connections and Optional External Components....... 11
Power Connections (VDD) ........................................ 11
External Reset (XRES).............................................. 11
Dual-Bonded GPIO Connections .............................. 11
External 32 kHz Clock/Crystal Oscillator Input.......... 11
Using CYBLE-013030-00 with External Flash........... 11
Critical Components List ........................................... 13
Antenna Design......................................................... 13
Bluetooth Baseband Core ............................................. 14
Security ........................................................................... 15
ADC Port.......................................................................... 16
Serial Peripheral Interface ............................................. 17
Microprocessor Unit....................................................... 18
External Reset (XRES).............................................. 18
Integrated Radio Transceiver ........................................ 19
Transmitter Path........................................................ 19
Digital Modulator ....................................................... 19
Power Amplifier ......................................................... 19
Receiver Path............................................................ 19
Digital Demodulator and Bit Synchronizer................. 19
Receiver Signal Strength Indicator............................ 19
Local Oscillator (LO).................................................. 20
Calibration ................................................................. 20
Internal LDO Regulator ............................................. 20
Peripheral Transport Unit .......................................... 20
Clock Frequencies.......................................................... 21
Peripheral Block ........................................................ 21
32 kHz Crystal Oscillator (Optional) .......................... 21
GPIO Port ........................................................................ 22
Document Number: 002-19200 Rev. **
PWM................................................................................. 22
Power Management Unit................................................ 24
RF Power Management ............................................ 24
Host Controller Power Management ......................... 24
BBC Power Management.......................................... 24
Electrical Characteristics............................................... 25
RF Specifications ........................................................... 27
Timing and AC Characteristics ..................................... 29
UART Timing............................................................. 29
SPI Timing................................................................. 29
BSC Interface Timing ................................................ 31
Environmental Specifications ....................................... 32
Environmental Compliance ....................................... 32
RF Certification.......................................................... 32
Safety Certification .................................................... 32
Environmental Conditions ......................................... 32
ESD and EMI Protection ........................................... 32
Regulatory Information .................................................. 33
FCC ........................................................................... 33
Innovation, Science and Economic Development (ISED)
Canada Certification ......................................................... 34
European Declaration of Conformity ......................... 35
MIC Japan ................................................................. 35
Packaging........................................................................ 36
Ordering Information...................................................... 38
Acronyms ........................................................................ 39
Document Conventions ................................................. 39
Units of Measure ....................................................... 39
Document History Page ................................................. 40
Sales, Solutions, and Legal Information ...................... 41
Worldwide Sales and Design Support....................... 41
Products .................................................................... 41
PSoC® Solutions ...................................................... 41
Cypress Developer Community................................. 41
Technical Support ..................................................... 41
Page 3 of 41
CYBLE-013025-00
CYBLE-013030-00
PRELIMINARY
Overview
Functional Block Diagram
Figure 1 illustrates the CYBLE-0130XX-00 functional block diagram.
Figure 1. Functional Block Diagram
Module Description
The CYBLE-0130XX-00 module is a complete module designed to be soldered to the application’s main board.
Module Dimensions and Drawing
Cypress reserves the right to select components from various vendors to achieve the Bluetooth module functionality. Such selections
will still guarantee that all mechanical specifications and module certifications are maintained. Designs should be held within the
physical dimensions shown in the mechanical drawings in Figure 2 on page 5. All dimensions are in millimeters (mm).
Table 1. Module Design Dimensions
Dimension Item
Module dimensions
Antenna connection location dimensions
PCB thickness
Specification
Length (X)
14.52 ± 0.10 mm
Width (Y)
19.50 ± 0.10 mm
Length (X)
14.52 mm
Width (Y)
4.80 mm
Height (H)
0.80 ± 0.10 mm
Shield height
Height (H)
1.45 mm typical
Maximum component height
Height (H)
1.45 mm typical
Total module thickness (bottom of module to highest component)
Height (H)
2.25 mm typical
See Table 2 on page 5 for the CYBLE-0130XX-00 mechanical reference drawing.
Document Number: 002-19200 Rev. **
Page 4 of 41
PRELIMINARY
CYBLE-013025-00
CYBLE-013030-00
Figure 2. Module Mechanical Drawing
Top View (See from Top)
Side View
Bottom View (Seen from Bottom)
Notes
2. No metal should be located beneath or above the antenna area. Only bare PCB material should be located beneath the antenna area. For more information on
recommended host PCB layout, see “Recommended Host PCB Layout” on page 7.
3. The CYBLE-013025-00 includes castellated pad connections, denoted as the circular openings at the pad location above.
Document Number: 002-19200 Rev. **
Page 5 of 41
CYBLE-013025-00
CYBLE-013030-00
PRELIMINARY
Pad Connection Interface
As shown in the bottom view of Figure 2 on page 5, the CYBLE-0130XX-00 connects to the host board via solder pads on the backside
of the module. Table 2 and Figure 3 detail the solder pad length, width, and pitch dimensions of the CYBLE-0130XX-00 module.
Table 2. Connection Description
Name
Connections
Connection Type
Pad Length Dimension
Pad Width Dimension
Pad Pitch
SP
31
Solder Pads
1.02 mm
0.71 mm
1.27 mm
Figure 3. Solder Pad Dimensions (Seen from Bottom
To maximize RF performance, the host layout should follow these recommendations:
1. Antenna Area Keepout: The host board directly below the antenna area of the Cypress module (see Figure 2 on page 5) must
contain no ground or signal traces. This keep out area requirement applies to all layers of the host board.
2. Module Placement: The ideal placement of the Cypress Bluetooth module is in a corner of the host board with the PCB trace
antenna located at the far corner. This placement minimizes the additional recommended keep out area stated in item 2. Refer to
AN96841 for module placement best practices.
Figure 4. Recommended Host PCB Keep Out Area Around the CYBLE-0130XX-00 Antenna
Document Number: 002-19200 Rev. **
Page 6 of 41
PRELIMINARY
CYBLE-013025-00
CYBLE-013030-00
Recommended Host PCB Layout
Figure 5, Figure 6, Figure 7, and Table 3 provide details that can be used for the recommended host PCB layout pattern for the
CYBLE-0130XX-00. Dimensions are in millimeters unless otherwise noted. Pad length of 1.27 mm (0.635 mm from center of the pad
on either side) shown in Figure 7 is the minimum recommended host pad length. The host PCB layout pattern can be completed using
either Figure 5, Figure 6, or Figure 7. It is not necessary to use all figures to complete the host PCB layout pattern.
Figure 5. CYBLE-0130XX-00 Host Layout (Dimensioned)
Figure 6. CYBLE-0130XX-00 Host Layout (Relative to Origin)
Top View (Seen on Host PCB)
Top View (Seen on Host PCB)
Document Number: 002-19200 Rev. **
Page 7 of 41
PRELIMINARY
CYBLE-013025-00
CYBLE-013030-00
Table 3 provides the center location for each solder pad on the CYBLE-0130XX-00. All dimensions are referenced to the center of the
solder pad. Refer to Figure 6 for the location of each module solder pad.
Table 3. Module Solder Pad Location
Figure 7. Solder Pad Reference Location
Solder Pad
(Center of Pad)
Location (X,Y) from
Orign (mm)
Dimension from
Orign (mils)
1
(0.39, 4.88)
(15.35, 192.13)
2
(0.39, 6.15)
(15.35, 242.13)
3
(0.39, 7.42)
(15.35, 292.13)
4
(0.39, 8.69)
(15.35, 342.13)
5
(0.39, 9.96)
(15.35, 392.13)
6
(0.39, 11.23)
(15.35, 442.13)
7
(0.39, 12.50)
(15.35, 492.13)
8
(0.39, 13.77)
(15.35, 542.13)
9
(0.39, 15.04)
(15.35, 592.13)
10
(0.39, 16.31)
(15.35, 642.13)
11
(0.39, 17.58)
(15.35, 692.13)
12
(2.04, 18.82)
(80.31, 740.94)
13
(3.31, 18.82)
(130.31, 740.94)
14
(4.58, 18.82)
(180.31, 740.94)
15
(5.85, 18.82)
(230.31, 740.94)
16
(7.12, 18.82)
(280.31, 740.94)
17
(8.39, 18.82)
(330.31, 740.94)
18
(9.66, 18.82)
(380.31, 740.94)
19
(10.93, 18.82)
(430.31, 740.94)
20
(12.20, 18.82)
(480.31, 740.94)
21
(13.47, 18.82)
(530.31, 740.94)
22
(14.14, 16.31)
(556.69, 642.12)
23
(14.14, 15.04)
(556.69, 592.12)
24
(14.14, 13.77)
(556.69, 542.12)
25
(14.14, 12.50)
(556.69, 492.12)
26
(14.14, 11.23)
(556.69, 442.12)
27
(14.14, 9.96)
(556.69, 392.12)
28
(14.14, 8.69)
(556.69, 342.12)
29
(14.14, 7.42)
(556.69, 292.12)
30
(14.14, 6.15)
(556.69, 242.12)
31
(14.14, 4.88)
(556.69, 192.12)
Document Number: 002-19200 Rev. **
Top View (Seen on Host PCB)
Page 8 of 41
CYBLE-013025-00
CYBLE-013030-00
PRELIMINARY
Module Connections
Table 4 and Table 5 detail the solder pad connection definitions and available functions for the pad connections for the
CYBLE-013025-00 and CYBLE-013030-00 respectively. Table 4 and Table 5 lists the solder pads on the CYBLE-0130XX-00 modules,
the silicon device pin, and denotes what functions are available for each solder pad.
Table 4. CYBLE-013025-00 Solder Pad Connection Definitions
SPI[4]
Pad
Pad Name
1
XRES
UART
External Reset (Active Low)
2
GND/NC
Ground/No Connect
3
GND/NC
4
P11/27[5]
5
P12/26[6]
SPI2_CS (P26)
(slave)
6
P15
P14/38[6]
8
P13/28[6]
9
P24
ADC
PWM
QD[5]
CLK/XTAL
GPIO
✓
(P11)
PWM1
(P27)
OC1
(P27)
XTALI32K
(P11)
✓
✓
(P12))
PWM0
(P26)
OC0
(P26)
XTALO32K
(P12)
✓
✓
SPI2_MOSI (P38)
(master/slave)
✓
✓
(P14/P38)
PWM2
(P14)
✓
(P13/P28)
PWM3
(P13)
PWM2
(P28)
OC2
(P28)
SPI2_CLK
(master/slave)
PUART_TX
✓
✓
NC
Not Connect
11
NC
Not Connect
12
P25
PUART_RX
SPI2_MISO
(master/slave)
13
P4
PUART_RX
SPI2_MOSI
(master/slave)
Y0
✓
14
P2
PUART_RX
SPI2_MOSI (master)/
SPI2_CS (slave)
X0
✓
15
VDD
PUART_CTS
SPI2_CLK
(master/slave)
X1
✓
P3
SWDIO
✓
10
16
Other
Ground/No Connect
SPI2_MOSI (P27)
(master/slave)
7
I2C
✓
VDD (2.3 V ~ 3.63 V)
17
P8/33[6]
No Connect (Used for on-module memory SPI interface for CYBLE-013025-00)
18
P32
No Connect (Used for on-module memory SPI interface for CYBLE-013025-00)
19
P1
PUART_RTS
SPI2_MISO
(master/slave)
✓
✓
20
P0
PUART_TX
SPI2_MOSI
(master/slave)
✓
✓
21
SDA
I2C_SDA
✓
22
SCL
I2C_SCL
✓
23
UP_TX
UART_TXD
24
UP_RX
UART_RXD
25
GND
Ground
26
GND
Ground
27
GND
Ground
28
GND
Ground
29
NC
Not Connect
30
NC
Not Connect
31
NC
Not Connect
✓
✓
Notes
4. The CYBLE-013025-00 contains a single SPI (SPI2) peripheral supporting both master or slave configurations. SPI1 is used for on-module serial memory interface.
5. Quadrature Decoder.
6. The chip pin for this connection is dual-bonded. Use of the internal chip super-mux is required to configure the desired output signal on these connections.
Document Number: 002-19200 Rev. **
Page 9 of 41
CYBLE-013025-00
CYBLE-013030-00
PRELIMINARY
Table 5. CYBLE-013030-00 Solder Pad Connection Definitions
Pad
Pad Name
SPI[7]
UART
I2C
ADC
PWM
1
XRES
External Reset (Active Low)
2
GND/NC
Ground/No Connect
3
GND/NC
QD[8]
CLK/XTAL
GPIO
Ground/No Connect
✓
(P11)
PWM1
(P27)
OC1
(P27)
XTALI32K
(P11)
✓
PWM0
(P26)
OC0
(P26)
XTALO32K
(P12)
✓
4
P11/27[9]
SPI2_MOSI (P27)
(master/slave)
5
P12/26[9]
SPI1_MISO (P26, Master)
SPI2_CS (P26, slave)
✓
(P12))
6
P15
SPI2_MOSI (P38)
(master/slave)
✓
(P14/P38)
PWM2
(P14)
✓
(P13/P28)
PWM3
(P13)
PWM2
(P28)
✓
[9]
7
P14/38
8
P13/28[9]
9
P24
Other
PUART_TX
✓
SWDIO
✓
OC2
(P28)
✓
SPI1_MISO (master)
SPI2_CLK (master/slave)
✓
10
NC
Not Connect
11
NC
Not Connect
12
P25
PUART_RX
13
P4
PUART_RX
SPI2_MOSI (master)
Y0
✓
PUART_RX
SPI2_MOSI (master)/
SPI2_CS (slave)
X0
✓
X1
✓
SPI2_MISO
(master/slave)
✓
14
P2
15
VDD
16
P3
PUART_CTS
SPI2_CLK
(master/slave)
17
P8/33[7]
PUART_RX
(P33)
SPI2_MOSI (P33) (slave)
SPI1_CS (P33) (master)
✓
(P8/P33)
18
P32
PUART_TX
SPI1_MISO (master)
SPI2_CS (slave)
✓
19
P1
PUART_RTS
SPI2_MISO
(master/slave)
✓
✓
20
P0
PUART_TX
SPI2_MOSI
(master/slave)
✓
✓
21
SDA
VDD (1.62V - 3.63V)
X1
(P33)
ACLK1
(P33)
✓
ACLK0
✓
SPI1_MOSI (master)
I2C_SDA
✓
SP1_CLK (master)
I2C_SCL
✓
22
SCL
23
UP_TX
UART_TXD
24
UP_RX
UART_RXD
25
GND
Ground
26
GND
Ground
27
GND
Ground
28
GND
Ground
29
NC
Not Connect
30
NC
Not Connect
31
NC
Not Connect
✓
✓
Notes
7. The CYBLE-013025-00 contains a single SPI (SPI2) peripheral supporting both master or slave configurations. SPI1 is used for on-module serial memory interface.
8. Quadrature Decoder.
9. The chip pin for this connection is dual-bonded. Use of the internal chip super-mux is required to configure the desired output signal on these connections.
Document Number: 002-19200 Rev. **
Page 10 of 41
PRELIMINARY
CYBLE-013025-00
CYBLE-013030-00
Connections and Optional External Components
Power Connections (VDD)
The CYBLE-0130XX-00 contains one power supply connection, VDD, which accepts a supply input range of 2.3 V to 3.63 V
(CYBLE-013025-00) or 1.62 V to 3.63 V (CYBLE-013030-00). Table 14 provides these specifications. The maximum power supply
ripple for this power connection is 100 mV, as shown in Table 14.
It is not required to add any power supply decoupling or noise reduction circuitry on the host PCB. If desired, an external ferrite bead
between the supply and the module connection can be included, but is not necessary. If used, the ferrite bead should be positioned
as close as possible to the module connection. If used, the recommended ferrite bead value is 330 , 100 MHz.
External Reset (XRES)
The CYBLE-0130XX-00 has an integrated power-on reset circuit, which completely resets all circuits to a known power on state. This
action can also be evoked by an external reset signal, forcing it into a power-on reset state. The XRES signal is an active-low signal,
which is an input to the CYBLE-0130XX-00 module (solder pad 1). The CYBLE-0130XX-00 module does not require an external
pull-up resistor on the XRES input
During power-on operation, the XRES connection to the CYBLE-0130XX-00 is required to be held low 50 ms after the VDD power
supply input to the module is stable. This can be accomplished in the following ways:
■
The host device should connect a GPIO to the XRES of Cypress CYBLE-0130XX-00 module and pull XRES low until VDD is stable.
XRES is recommended to be released 50 ms after VDD is stable.
■
If the XRES connection of the CYBLE-0130XX-00 module is not used in the application, a 0.47-µF capacitor may be connected to
the XRES solder pad of the CYBLE-0130XX-00 to delay the XRES release. The capacitor value for this recommended implementation
is approximate, and the exact value may differ depending on the VDD power supply ramp time of the system. The capacitor value
should result in an XRES release timing of 50 ms after VDD stability.
■
The XRES release may be controlled by a external voltage detection circuit. XRES should be released 50 ms after VDD is stable.
Refer to Figure 10 on page 19 for XRES operating and timing requirements during power on events.
Dual-Bonded GPIO Connections
The CYBLE-013030-00 contains five GPIOs that are dual-bonded at the silicon level (four such pins exist on the CYBLE-013025-00).
Solder pads 4, 5, 7, 8, and 17 are the module connections with dual-bonded silicon I/O. If any of these dual-bonded GPIO are used,
only the functionality and features for one of these port pins may be used. The desired port pin should be configured in the WICED
SMART SDK. For details on the features and functions that each of these dual-bonded GPIOs provide, refer to Table 4 and Table 5.
For additional information on all available GPIOs, refer to GPIO Port on page 22.
External 32-kHz Clock/Crystal Oscillator Input
The CYBLE-0130XX-00 provides the option to connect an external 32-kHz crystal oscillator or clock input instead of using the internal
Local Oscillator (LO). Solder pads 4 and 5 of the CYBLE-0130XX-00 module provide this connection option. Note that these connections are also dual-bonded GPIOs, requiring the appropriate GPIO to be selected to enable external clocking functionality. The specific
pins required are as follows:
■
Module Solder Pad 4, Silicon GPIO P11 - Must be assigned as XTALI32K (Crystal Input terminal)
■
Module Solder Pad 5, Silicon GPIO P12 - Must be assigned as XTALO32K (Crystal Output terminal)
This option may be desired for customers who wish to achieve minimum power consumption in their application. Refer to 32-kHz
Crystal Oscillator (Optional) on page 21 for details on the requirements for an external 32-kHz input to the CYBLE-0130XX-00.
Using CYBLE-013030-00 with External Flash
The CYBLE-013030-00 does not contain any on-module nonvolatile memory. If desired, the CYBLE-013030-00 can be used with an
external memory device (EEPROM or SFLASH). If EEPROM is used as an external memory device with I2C interface, module solder
pads 21 (SDA) and 22 (SCL) must be used as the I2C interface.
If using external SFLASH as the memory interface, SPI1 (master) must be used as the interface to the SFLASH device. The specific
GPIO required and the applicable SPI signal is listed below. These are the same signals used for the SFLASH interface on the
CYBLE-013025-00.
1. SPI signal MOSI: Module Solder Pad 21, silicon GPIO SDA
2. SPI signal MISO: Module Solder Pad 18, silicon GPIO P32
3. SPI Signal CLK: Module Solder Pad 22, silicon GPIO SCL
4. SPI Signal CS: Module Solder Pad 17, silicon GPIO P8
Document Number: 002-19200 Rev. **
Page 11 of 41
PRELIMINARY
CYBLE-013025-00
CYBLE-013030-00
Figure 8 illustrates the CYBLE-013025-00 schematic.
Figure 8. CYBLE-013025-00 Schematic Diagram
Document Number: 002-19200 Rev. **
Page 12 of 41
CYBLE-013025-00
CYBLE-013030-00
PRELIMINARY
Critical Components List
Table 6 details the critical components used in the CYBLE-0130XX-00 module.
Table 6. Critical Component List
Component
Reference Designator
Description
Silicon
U1
32-pin QFN BLE Silicon Device - CYW20737
Silicon
U2
8-pin TDF8N, 128K Serial Flash (CYBLE-013025-00)
Crystal
Y1
24.000 MHz, 12PF
Antenna Design
Table 7 details the trace antenna used in the CYBLE-0130XX-00 module. For more information, see Table 7.
Table 7. Trace Antenna Specifications
Item
Frequency Range
Description
2400–2500 MHz
Peak Gain
–0.5 dBi
Return Loss
10 dB minimum
Document Number: 002-19200 Rev. **
Page 13 of 41
PRELIMINARY
CYBLE-013025-00
CYBLE-013030-00
Bluetooth Baseband Core
The Bluetooth Baseband Core (BBC) implements all of the time-critical functions required for a high-performance Bluetooth operation. The BBC manages the buffering, segmentation, and data routing for all connections. It also buffers data that passes through it,
handles data flow control, schedules ACL TX/RX transactions, monitors Bluetooth slot usage, optimally segments and packages
data into baseband packets, manages connection status indicators, and composes and decodes HCI packets. In addition to these
functions, it independently handles HCI event types and HCI command types.
The following transmit and receive functions are also implemented in the BBC hardware to increase TX/RX data reliability and security
before sending over the air:
■
■
Receive Functions: symbol timing recovery, data deframing, forward error correction (FEC), header error control (HEC), cyclic
redundancy check (CRC), data decryption, and data dewhitening.
Transmit Functions: data framing, FEC generation, HEC generation, CRC generation, link key generation, data encryption, and data
whitening.
Frequency Hopping Generator
The frequency hopping sequence generator selects the correct hopping channel number depending on the link controller state,
Bluetooth clock, and device address.
E0 Encryption
The encryption key and the encryption engine are implemented using dedicated hardware to reduce software complexity and provide
minimal processor intervention.
Link Control Layer
The link control layer is part of the Bluetooth link control functions that are implemented in dedicated logic in the Link Control Unit
(LCU). This layer consists of the Command Controller, which takes software commands, and other controllers that are activated or
configured by the Command Controller to perform the link control tasks. Each task performs a different Bluetooth link controller state.
STANDBY and CONNECTION are the two major states. In addition, there are four substates: page, page scan, inquiry, and inquiry
scan.
Adaptive Frequency Hopping
The CYBLE-0130XX-00 gathers link quality statistics on a channel-by-channel basis to facilitate channel assessment and channel
map selection. The link quality is determined by using both RF and baseband signal processing to provide a more accurate frequency
hop map.
Document Number: 002-19200 Rev. **
Page 14 of 41
PRELIMINARY
CYBLE-013025-00
CYBLE-013030-00
Bluetooth Low Energy Profiles
The CYBLE-0130XX-00 supports Bluetooth Low Energy (BLE), including the following profiles that are supported[10] in ROM:
■
Battery status
■
Blood pressure monitor
■
Find me
■
Heart rate monitor
■
Proximity
■
Thermometer
■
Weight scale
■
Time
■
Alliance for Wireless Power (A4WP) wireless charging
■
Automation profile
■
Support for secure OTA (external memory required for CYBLE-013030-00)
The following additional profiles can be supported[10] from RAM:
■
Blood glucose monitor
■
Temperature alarm
■
Location
■
Custom profile
Test Mode Support
The CYBLE-0130XX-00 supports Bluetooth Test mode, as described in the Bluetooth Low Energy specification.
Security
CYBLE-0130XX-00 provides mechanisms for implementing security and authentication schemes using:
■
RSA (Public Key Cryptography)
■
X.509 (excluding parsing)
■
Hash functions: MD5, SHA-1, SHA-224, SHA-256, SHA-384, SHA-512
■
Message authentication code: HMAC MD5, HMAC SHA-1
Note
10. Full qualification and use of these profiles may require FW updates from Cypress. Some of these profiles are under development/approval at the Bluetooth SIG and
conformity with the final approved version is pending. Contact your local representative for updates and the latest list of profiles.
Document Number: 002-19200 Rev. **
Page 15 of 41
CYBLE-013025-00
CYBLE-013030-00
PRELIMINARY
ADC Port
The CYBLE-0130XX-00 contains a 16-bit ADC (effective number of bits is 10).
Additionally:
■
■
There are nine analog input channels in the 31-pad module
The following GPIOs can be used as ADC inputs (module pad number denoted in [ ]):
P0 [Pad 20]
❐ P1 [Pad 19]
❐ P8/P33 (select only one[11]) [Pad 17]
❐ P11 on P11/P27[12] pin [Pad 4]
❐ P12 on P12/28[12] pin [Pad 5]
❐ P13/P28[11] (select only one) [Pad 8]
❐ P14/P38[11] (select only one) [Pad 7]
❐ P15 [Pad 6]
❐ P32 [Pad 18]
❐
■
The conversion time is 10 us.
■
There is a built-in reference with supply- or bandgap-based reference modes.
■
The maximum conversion rate is 187 kHz.
■
There is a rail-to-rail input swing.
The ADC consists of an analog ADC core that performs the actual analog-to-digital conversion and digital hardware that processes
the output of the ADC core into valid ADC output samples.
The ADC input range is selectable by firmware control:
■
When an input range of 0~3.6 V is used, the input impedance is 3 MW.
■
When an input range of 0~2.4 V is used, the input impedance is 1.84 MW.
■
When an input range of 0~1.2 V is used, the input impedance is 680 kW.
ADC modes are defined in Table 8.
Table 8. ADC Modes
Mode
Effective Number of Bits (Typical)
Maximum Sampling Rate (kHz)
Latency[13] (us)
0
13
5.859
171
1
12.6
11.7
85
2
12
46.875
21
3
11.5
93.75
11
4
10
187
5
Notes
11. Either signal on these dual-bonded connections may be used for ADC functionality.
12. Only the specified port-pin connection may be used for ADC functionality (for example, only a P11 configuration on module pad 4 (P11/P27) may be used for ADC
functionality.
13.Settling time after switching channels.
Document Number: 002-19200 Rev. **
Page 16 of 41
CYBLE-013025-00
CYBLE-013030-00
PRELIMINARY
Serial Peripheral Interface
The CYBLE-0130XX-00 has two independent SPI interfaces, SPI1 and SPI2. One is a master-only (SPI1) interface and the other can
be either a master or a slave (SPI2). Each interface has a 16-byte transmit buffer and a 16-byte receive buffer. The CYBLE-013025-00
has one SPI interface available to the user (SPI2). SPI1 is used as the on-board SFLASH interface on the CYBLE-013025-00.
CYBLE-013030-00 has both SPI interfaces available to the user. If an external SFLASH memory is used, SPI1 should be used as the
interface to the memory device.
The CYBLE-0130XX-00 can act as an SPI master device that supports 1.8 V or 3.3 V SPI slaves. The CYBLE-0130XX-00 can also
act as an SPI slave device that supports a 1.8 V or 3.3 V SPI master. Table 9, Table 10, and Table 11 details the available signal
connections on BLE silicon device for each SPI function. The module solder pad number for each silicon connection is shown in
Table 4 and Table 5.
Table 9 details the available SPI master mode connections when a SPI serial flash connection is present (detault for the
CYBLE-013025-00, and optional for the CYBLE-013030-00). Table 10 details the available SPI master mode connections when there
is no SPI serial flash connected to the module (only the case for the CYBLE-013030-00). Table 11 details the available SPI slave
mode connections under no restrictions.
Table 9. CYBLE-0130XX-00 SPI1 (Master Mode)
Pin Name
Configured Pin Name
SPI_CLK
SPI_MOSI
SPI_MISO[14]
SPI_CS[15]
SCL [Pad 22]
SDA [Pad 21]
P32 [Pad 18]
P33[16] [Pad 17]
SPI_CLK
SPI_MOSI
SPI_MISO
SPI_CS[17]
P3 [Pad 16]
P0 [Pad 20]
P1 [Pad 19]
–
P24 [Pad 9]
P4 [Pad 13]
P25 [Pad 12]
–
–
P27 [Pad 4]
–
–
Table 10. CYBLE-0130XX-00 SPI2 (Master Mode)
Pin Name
Configured Pin Name
Table 11. CYBLE-0130XX-00 SPI2 (Slave Mode)
Pin Name
Configured Pin Name
SPI_CLK
SPI_MOSI
SPI_MISO
SPI_CS
P3 [Pad 16]
P0 [Pad 20]
P1 [Pad 19]
P2 [Pad 14]
P24 [Pad 9]
P27 [Pad 4]
P25 [Pad 12]
P26 [Pad 5]
–
P33 [Pad 17]
–
P32 [Pad 18]
Notes
14.SPI1 MISO should always be P32 (solder pad 18). Boot ROM of the silicon device does not configure any others.
15.Any GPIO can be used as SPI_CS when SPI1 is in master mode, and when the SPI slave is not a serial flash.
16.P33 (solder pad 17) is always SPI_CS when a serial flash is used for nonvolatile storage. This is also the case for the CYBLE-013025-00.
17. Any available GPIO can be used as SPI_CS when SPI2 is in master mode.
Document Number: 002-19200 Rev. **
Page 17 of 41
PRELIMINARY
CYBLE-013025-00
CYBLE-013030-00
Microprocessor Unit
The CYBLE-0130XX-00 microprocessor unit (µPU) executes software from the link control (LC) layer up to the application layer
components. The microprocessor is based on an ARM® Cortex® M3, 32-bit RISC processor. The µPU has 320 KB of ROM for program
storage and boot-up, 60 KB of RAM for scratch-pad data, and patch RAM code. The SoC has a total storage of 380 KB, including
RAM and ROM.
The internal boot ROM provides power-on reset flexibility, which enables the same device to be used in different HID applications with
an external serial EEPROM or with an external serial flash memory. At power-up, the lowest layer of the protocol stack is executed
from the internal ROM memory.
External patches may be applied to the ROM-based firmware to provide flexibility for bug fixes and feature additions. The device
also supports the integration of user applications.
External Reset (XRES)
The CYBLE-0130XX-00 has an integrated power-on reset circuit that completely resets all circuits to a known power-on state. An
external active low reset signal, XRES, can be used to put the CYBLE-0130XX-00 in the reset state.
Figure 9. External Reset (XRES) Timing
External Reset (XRES) Recommended External Components and Power On Operation
During a power-on event, the XRES line of the CYBLE-0130XX-00 is required to be held low 50 ms after the VDD power supply input
to the module is stable. Refer to Figure 10 for the Power On XRES timing operation. This power-on operation can be accomplished
in the following ways:
■
A host device should connect a GPIO to the XRES of Cypress CYBLE-0130XX-00 module and pull XRES low until VDD is stable.
XRES can be released after VDD is stable.
■
If the XRES connection of the CYBLE-0130XX-00 module is not used in the application, a 0.47-µF capacitor may be connected to
the XRES solder pad of the CYBLE-0130XX-00.
■
The XRES release timing can also be controlled via a external voltage detection circuit.
Document Number: 002-19200 Rev. **
Page 18 of 41
PRELIMINARY
CYBLE-013025-00
CYBLE-013030-00
Figure 10. Power-On External Reset (XRES) Operation
Integrated Radio Transceiver
The CYBLE-0130XX-00 has an integrated radio transceiver that is optimized for 2.4-GHz Bluetooth wireless systems. It has been
designed to provide low power, low cost, and robust communications for applications operating in the globally available 2.4-GHz
unlicensed ISM band. It is fully compliant with Bluetooth Radio Specification 4.1 and meets or exceeds the requirements to provide
the highest communication link quality of service.
Transmitter Path
The CYBLE-0130XX-00 features a fully integrated transmitter. The baseband transmit data is GFSK modulated in the 2.4-GHz ISM
band.
Digital Modulator
The digital modulator performs the data modulation and filtering required for the GFSK signal. The fully digital modulator minimizes
any frequency drift or anomalies in the modulation characteristics of the transmitted signal.
Power Amplifier
The CYBLE-0130XX-00 has an integrated power amplifier (PA) that can transmit up to +4 dBm for class 2 operation.
Receiver Path
The receiver path uses a low IF scheme to down convert the received signal for demodulation in the digital demodulator and bit synchronizer. The receiver path provides a high degree of linearity, and an extended dynamic range to ensure reliable operation in the
noisy 2.4-GHz ISM band. The front-end topology, which has built-in out-of-band attenuation, enables the CYBLE-0130XX-00 to be
used in most applications without off-chip filtering.
Digital Demodulator and Bit Synchronizer
The digital demodulator and bit synchronizer take the low-IF received signal and perform an optimal frequency tracking and bit synchronization algorithm.
Receiver Signal Strength Indicator
The radio portion of the CYBLE-0130XX-00 provides a receiver signal strength indicator (RSSI) to the baseband. This enables the
controller to take part in a Bluetooth power-controlled link by providing a metric of its own receiver signal strength to determine
whether the transmitter should increase or decrease its output power.
Document Number: 002-19200 Rev. **
Page 19 of 41
PRELIMINARY
CYBLE-013025-00
CYBLE-013030-00
Local Oscillator (LO)
The accuracy of the local oscillator is ±250 ppm. The CYBLE-0130XX-00 is designed to use the LO for sleep mode operation and
power savings.
Additional power consumption savings can be achieved by connecting an accurate external crystal oscillator to the CYBLE-0130XX-00
module. If used, the external crystal oscillator connects to Pads 4 (P11 - input) and 5 (P12 - output) of the CYBLE-0130XX-00. Refer
to 32-kHz Crystal Oscillator (Optional) on page 21 for more details.
Calibration
The CYBLE-0130XX-00 radio transceiver features a self-contained automated calibration scheme. No user interaction is required
during normal operation or during manufacturing to provide optimal performance. Calibration compensates for filter, matching network,
and amplifier gain and phase characteristics to yield radio performance within 2% of what is optimal. Calibration takes process and
temperature variations into account, and it takes place transparently during normal operation and hop setting times.
Internal LDO Regulator
The CYBLE-0130XX-00 has an integrated 1.2-V LDO regulator that provides power to the digital and RF circuits. The 1.2-V LDO
regulator operates from a 2.3 V to 3.63 V (CYBLE-013025-00) or 1.62 V to 3.63 V (CYBLE-013030-00) input supply with a 30-mA
maximum load current.
Peripheral Transport Unit
Broadcom Serial Communications Interface
The CYBLE-0130XX-00 provides a 2-pin master BSC interface, which can be used to retrieve configuration information from an
external EEPROM or to communicate with peripherals such as track-ball or touch-pad modules, and motion tracking ICs used in
mouse devices. The BSC interface is compatible with I2C slave devices. The BSC does not support multimaster capability or flexible
wait-state insertion by either master or slave devices.
The following transfer clock rates are supported by the BSC:
■
100 kHz
■
400 kHz
■
800 kHz (not a standard I2C-compatible speed.)
■
1 MHz (Compatibility with high-speed I2C-compatible devices is not guaranteed.)
The following transfer types are supported by the BSC:
■
Read (Up to 16 bytes can be read.)
■
Write (Up to 16 bytes can be written.)
■
Read-then-Write (Up to 16 bytes can be read and up to 16 bytes can be written.)
■
Write-then-Read (Up to 16 bytes can be written and up to 16 bytes can be read.)
Hardware controls the transfers, requiring minimal firmware setup and supervision.
The clock pin (SCL) and data pin (SDA) are both open-drain I/O pins. Pull-up resistors external to the CYBLE-0130XX-00 are required
on both the SCL and SDA pins for proper operation. The CYBLE-013025-00 does allow for I2C operation, even though the SDA and
SCL connections are used for on-board memory interface. WICED Smart SDK Version 2.2.3 must be used for I2C operation to work
on the CYBLE-013025-00.
UART Interface
The UART is a standard 2-wire interface (RX and TX) and has adjustable baud rates from 9600 bps to 1.5 Mbps. The baud rate can
be selected via a vendor-specific UART HCI command. The interface supports the Bluetooth 3.0 UART HCI (H4) specification. The
default baud rate for H4 is 115.2 kbaud.
Both high and low baud rates can be supported by running the UART clock at 24 MHz.
The CYBLE-0130XX-00 UART operates correctly with the host UART as long as the combined baud rate error of the two devices is
within ±5%.
Document Number: 002-19200 Rev. **
Page 20 of 41
CYBLE-013025-00
CYBLE-013030-00
PRELIMINARY
Clock Frequencies
Crystal Oscillator
The CYBLE-0130XX-00 has an integrated 24-MHz crystal on the module. There is no need to add an additional crystal oscillator.
Peripheral Block
The peripheral blocks of the CYBLE-0130XX-00 all run from a single 128 kHz low-power RC oscillator. The oscillator can be turned
on at the request of any of the peripherals. If the peripheral is not enabled, it shall not assert its clock request line.
The keyboard scanner is a special case, in that it may drop its clock request line even when enabled, and then reassert the clock
request line if a keypress is detected.
32-kHz Crystal Oscillator (Optional)
The use of an external 32-kHz crystal oscillator is optional for the CYBLE-0130XX-00 module. Figure 11 shows the 32-kHz crystal
(XTAL) oscillator with external components and Table 12 list the oscillator’s characteristics. It is a standard Pierce oscillator using a
comparator with hysteresis on the output to create a single-ended digital output. The hysteresis was added to eliminate any chatter
when the input is around the threshold of the comparator and is ~100 mV. This circuit can be operated with a 32 kHz or 32.768 kHz
crystal oscillator or be driven with a clock input at similar frequency. The default component values are: R1 = 10 M, C1 = C2 = ~10 pF.
The values of C1 and C2 are used to fine-tune the oscillator.
Figure 11. 32 kHz Oscillator Block Diagram
Parameter
Table 12. XTAL Oscillator Characteristics
Conditions
Minimum
Typical
Maximum
Unit
Output frequency
Foscout
Symbol
–
–
32.768
–
kHz
Frequency
tolerance
–
Crystal dependent
–
100
–
ppm
Start-up time
Tstartup
–
–
–
500
ms
XTAL drive level
Pdrv
For crystal selection
0.5
–
–
W
XTAL series resistance
Rseries
For crystal selection
–
–
70
k
XTAL shunt capacitance
Cshunt
For crystal selection
–
–
1.3
pF
If used, the external crystal oscillator connects to Pad 4 (P11 - input) and Pad 5 (P12 - output) of the CYBLE-0130XX-00. Refer to
Table 4 and Table 5 for more details on the available functions for each solder pad connections.
Document Number: 002-19200 Rev. **
Page 21 of 41
PRELIMINARY
CYBLE-013025-00
CYBLE-013030-00
GPIO Port
The CYBLE-0130XX-00 has 14 GPIOs, which can be used for Serial Communication, I/O control, and other GPIO functionality. All
GPIOs support programmable pull-up and pull-down resistors, and all support a 2 mA drive strength except P26, P27, and P28, which
provide a 16 mA drive strength at 3.3-V supply. The following GPIOs are available:
■
P0-P4
■
P8/P33 only available for CYBLE-013030-00
■
P11/P27 (Dual bonded, only one of two is available)
■
P12/P26 (Dual bonded, only one of two is available)
■
P13/P28 (Dual bonded, only one of two is available)
■
P14/P38 (Dual bonded, only one of two is available)
■
P15
■
P24
■
P25
■
P32 - only available for CYBLE-013030-00
For a description of the capabilities of all GPIOs, see Table 4 and Table 5.
PWM
The CYBLE-0130XX-00 has four PWMs. The PWM module consists of the following:
■
PWM0-3
■
The following GPIOs can be mapped as PWMs; module pad assignments are shown in Table 4 and Table 5:
❐ P26 on P12/P26 [Pad 5]
❐ P27 on P11/P27 [Pad 4]
❐ P14 on P14/P38 [Pad 7]
❐ P13 on P13/P28 [Pad 8]
■
PWM0-3: Each of the four PWM channels contains the following registers:
❐ 10-bit initial value register (read/write)
❐ 10-bit toggle register (read/write)
❐ 10-bit PWM counter value register (read)
■
PWM configuration register shared among PWM0-3 (read/write). This 12-bit register is used:
❐ To configure each PWM channel
❐ To select the clock of each PWM channel
❐ To change the phase of each PWM channel
Figure 12 shows the structure of one PWM.
Document Number: 002-19200 Rev. **
Page 22 of 41
PRELIMINARY
CYBLE-013025-00
CYBLE-013030-00
Figure 12. PWM Block Diagram
Document Number: 002-19200 Rev. **
Page 23 of 41
PRELIMINARY
CYBLE-013025-00
CYBLE-013030-00
Power Management Unit
The Power Management Unit (PMU) provides power management features that can be invoked by software through power
management registers or packet-handling in the baseband core.
RF Power Management
The BBC generates power-down control signals for the transmit path, receive path, PLL, and power amplifier to the 2.4-GHz transceiver, which then processes the power-down functions accordingly.
Host Controller Power Management
Power is automatically managed by the firmware based on input device activity. As a power-saving task, the firmware controls the
disabling of the on-chip regulator when in deep sleep (HIDOFF) mode.
BBC Power Management
There are several low-power operations for the BBC:
■
Physical layer packet handling turns RF on and off dynamically within packet TX and RX.
■
Bluetooth-specified low-power connection mode. While in these low-power connection modes, the CYBLE-0130XX-00 runs on the
Low Power Oscillator and wakes up after a predefined time period.
The CYBLE-0130XX-00 automatically adjusts its power dissipation based on user activity. The following power modes are supported:
■
Active mode
■
Idle mode
■
Sleep mode
■
HIDOFF (Deep Sleep) mode
■
Timed Deep Sleep mode
The CYBLE-0130XX-00 transitions to the next lower state after a programmable period of user inactivity. Busy mode is immediately
entered when user activity resumes.
■
In HIDOFF (Deep Sleep) mode, the CYBLE-0130XX-00 baseband and core are powered off by disabling power to LDOOUT. The
VDDO domain remains powered up and will turn the remainder of the module on when it detects user events. This mode minimizes
chip power consumption and is intended for long periods of inactivity.
Document Number: 002-19200 Rev. **
Page 24 of 41
CYBLE-013025-00
CYBLE-013030-00
PRELIMINARY
Electrical Characteristics
Table 13 shows the maximum electrical rating for voltages referenced to VDD pin.
Table 13. Maximum Electrical Rating
Rating
Symbol
–
–
Topr
Tstg
VDD
Voltage on input or output pin
Operating ambient temperature range
Storage temperature range
Value
3.8
VSS – 0.3 to VDD + 0.3
–30 to +85
–40 to +125
Unit
V
V
°C
°C
Maximum[18]
3.63
3.63
100
Unit
V
V
mV
Table 14 shows the power supply characteristics for the range TJ = 0 to 125 °C.
Table 14. Power Supply
Parameter
VDD
VDD_RIPPLE
Description
Power Supply Input (CYBLE-013025-00)
Power Supply Input (CYBLE-013030-00)
Maximum power supply ripple for VDD input voltage
Minimum[18]
2.30
1.62
–
Typical
–
–
–
Table 15 shows the specifications for the ADC characteristics.
Table 15. ADC Specifications
Parameter
Symbol
Conditions
Min
Typ
Max
Unit
Number of Input channels
–
–
–
9
–
–
Channel switching rate
fch
–
–
–
133.33
kch/s
Input signal range
Reference settling time
Vinp
–
–
Changing refsel
0
–
3.63
V
7.5
–
–
s
Input resistance
Rinp
Effective, single ended
–
500
–
k
Input capacitance
Cinp
–
–
–
5
pF
Conversion rate
fC
–
5.859
–
187
kHz
Conversion time
TC
–
5.35
–
170.7
s
Resolution
R
–
–
16
–
bits
Effective number of bits
–
In specified performance range
–
See
Table 8 on
page 16
–
Absolute voltage
measurement error
–
Using on-chip ADC firmware driver
–
±2
–
Current
I
Iavdd1p2 + Iavdd3p3
–
–
1
mA
Power
P
–
–
1.5
–
mW
%
Leakage current
Ileakage
T = 25 °C
–
–
100
nA
Power-up time
Tpowerup
–
–
–
200
µs
Integral
nonlinearity[19]
Differential nonlinearity[19]
INL
In guaranteed performance range
–
–
1
LSB
DNL
In guaranteed performance range
–
–
1
LSB
Notes
18.Overall performance degrades beyond minimum and maximum supply voltages.
19. LSBs are expressed at the 10-bit level.
Document Number: 002-19200 Rev. **
Page 25 of 41
CYBLE-013025-00
CYBLE-013030-00
PRELIMINARY
Table 16 shows the specifications for the digital voltage levels.
Table 16. Digital Levels[20]
Symbol
Min
Typ
Max
Unit
Input low voltage
Characteristics
VIL
–
–
0.4
V
Input high voltage
VIH
0.75 × VDD
–
–
V
Input low voltage (VDD = 1.62V - CYBLE-013030-00 only)
VIL
–
–
0.4
V
Input high voltage (VDD = 1.62V - CYBLE-013030-00 only)
VIH
1.2
–
–
V
Output low voltage[21]
VOL
–
–
0.4
V
VOH
VDD – 0.4
–
–
V
CIN
–
0.12
–
pF
Output high
voltage[21]
Input capacitance (VDDMEM domain)
Table 17 shows the specifications for current consumption.
Table 17. Current Consumption
Operational Mode
Minimum
Typ
Maximum
Units
Conditions
Receive
–
26
28
mA
Receiver and baseband are both operating,
100% ON
Transmit
–
22
28
mA
Transmitter and baseband are both operating,
100% ON, +4 dBm
Sleep
–
50
60
µA
Average power with Fine Timer enabled at 1 ms
interval
I2C not used[22]
Deep Sleep (HIDOFF)
–
1.5
2.5
µA
Module can be awoken by external
event/interrupt or through timed wake
1-s Connection Interval
–
120
–
µA
Fine Timer setting of 1,000 ms
4-s Connection Interval
–
110
–
µA
Fine Timer setting of 1,000 ms
Notes
20. This table is also applicable to VDDMEM domain.
21. At the specified drive current for the pad.
Document Number: 002-19200 Rev. **
Page 26 of 41
CYBLE-013025-00
CYBLE-013030-00
PRELIMINARY
RF Specifications
Table 18. Receiver RF Specifications
Parameter
Mode and Conditions
Min
Typ
Max
Unit
2402
–
2480
MHz
[22]
Receiver Section
Frequency range
–
RX sensitivity (standard)
0.1%BER, 1 Mbps
RX sensitivity (low current)
–
–94
–
dBm
–
–91.5
–
dBm
Input IP3
–
–16
–
–
dBm
Maximum input
–
–10
–
–
dBm
–
–
21
dB
Interference
Performance[22, 23]
C/I cochannel
0.1%BER
C/I 1 MHz adjacent channel
0.1%BER
–
–
15
dB
C/I 2 MHz adjacent channel
0.1%BER
–
–
–17
dB
C/I 3 MHz adjacent channel
0.1%BER
–
–
–27
dB
C/I image channel
0.1%BER
–
–
–9.0
dB
C/I 1 MHz adjacent to image channel
0.1%BER
–
–
–15
dB
Out-of-Band Blocking Performance
(CW)[22, 23]
30 MHz to 2000 MHz
0.1%BER[24]
–
–30.0
–
dBm
2003 MHz to 2399 MHz
0.1%BER[25]
–
–35
–
dBm
2484 MHz to 2997 MHz
0.1%BER[25]
–
–35
–
dBm
3000 MHz to 12.75 GHz
0.1%BER[26]
–
–30.0
–
dBm
Spurious Emissions
30 MHz to 1 GHz
–
–
–
–57.0
dBm
1 GHz to 12.75 GHz
–
–
–
–55.0
dBm
Notes
22. I 30.8% PER.
23. Desired signal is 3 dB above the reference sensitivity level (defined as –70 dBm).
24. Measurement resolution is 10 MHz.
25. Measurement resolution is 3 MHz.
26. Measurement resolution is 25 MHz.
Document Number: 002-19200 Rev. **
Page 27 of 41
CYBLE-013025-00
CYBLE-013030-00
PRELIMINARY
Table 19. Transmitter RF Specifications
Parameter
Minimum
Typical
Maximum
Unit
Frequency range
2402
–
2480
MHz
Output power adjustment range
Transmitter Section
–20
–
4
dBm
Default output power
–
4.0
–
dBm
Output power variation
–
2.0
–
dB
|M – N| = 2
–
–
–20
dBm
|M – N| 3
–
–
–30
dBm
–
–
–36.0
dBm
Adjacent Channel Power
Out-of-Band Spurious Emission
30 MHz to 1 GHz
1 GHz to 12.75 GHz
–
–
–30.0
dBm
1.8 GHz to 1.9 GHz
–
–
–47.0
dBm
5.15 GHz to 5.3 GHz
–
–
–47.0
dBm
–
–
±150
kHz
Frequency drift
–
–
±50
kHz
Drift rate
–
–
20
kHz/50 µs
Average deviation in payload
(sequence used is 00001111)
225
–
275
kHz
Maximum deviation in payload
(sequence used is 10101010)
185
–
–
kHz
–
2
–
MHz
LO Performance
Initial carrier frequency tolerance
Frequency Drift
Frequency Deviation
Channel spacing
Document Number: 002-19200 Rev. **
Page 28 of 41
CYBLE-013025-00
CYBLE-013030-00
PRELIMINARY
Timing and AC Characteristics
In this section, use the numbers listed in the Reference column of each table to interpret the following timing diagrams.
UART Timing
Table 20. UART Timing Specifications
Reference
Min
Max
Unit
1
Delay time, UART_CTS low to UART_TXD valid
Characteristics
–
24
Baud out cycles
2
Setup time, UART_CTS high before midpoint of stop bit
–
10
ns
3
Delay time, midpoint of stop bit to UART_RTS high
–
2
Baud out cycles
Figure 13. UART Timing
SPI Timing
The SPI interface supports clock speeds up to 12 MHz with VDD 2.3V (CYBLE-0130XX-00). The supported clock speed is 6 MHz
when 2.3 V > VDD 1.62 V (CYBLE-013030-00 only).
Figure 14 and Figure 15 show the timing requirements when operating in SPI Mode 0 and 2, and SPI Mode 1 and 3, respectively.
Table 21. SPI Interface Timing Specifications
Reference
Characteristics
Min
Typ
Max
1 SCK
100
Master setup time
–
¾ SCK
–
3
Master hold time
¾ SCK
–
–
4
Slave setup time
–
¾ SCK
–
5
Slave hold time
¾ SCK
–
–
6
Time from last clock edge to CSN deasserted
1 SCK
10 SCK
100
1
Time from CSN asserted to first clock edge
2
Document Number: 002-19200 Rev. **
Page 29 of 41
PRELIMINARY
CYBLE-013025-00
CYBLE-013030-00
Figure 14. SPI Timing – Mode 0 and 2
Figure 15. SPI Timing – Mode 1 and 3
Document Number: 002-19200 Rev. **
Page 30 of 41
PRELIMINARY
CYBLE-013025-00
CYBLE-013030-00
BSC Interface Timing
Table 22. BSC Interface Timing Specifications
Reference
1
Characteristics
Clock frequency
Min
Max
Unit
–
100
kHz
400
800
1000
2
START condition setup time
650
–
ns
3
START condition hold time
280
–
ns
4
Clock low time
650
–
ns
5
Clock high time
280
–
ns
6
Data input hold time[27]
0
–
ns
7
Data input setup time
100
–
ns
8
STOP condition setup time
280
–
ns
9
Output valid from clock
–
400
ns
10
Bus free time[28]
650
–
ns
Figure 16. BSC Interface Timing Diagram
Notes
27. As a transmitter, 300 ns of delay is provided to bridge the undefined region of the falling edge of SCL to avoid unintended generation of START or STOP conditions.
28. Time that the cbus must be free before a new transaction can start.
Document Number: 002-19200 Rev. **
Page 31 of 41
CYBLE-013025-00
CYBLE-013030-00
PRELIMINARY
Environmental Specifications
Environmental Compliance
This CYBLE-0130XX-00 BLE module is produced in compliance with the Restriction of Hazardous Substances (RoHS) and
Halogen-Free (HF) directives. The Cypress module and components used to produce this module are RoHS and HF compliant.
RF Certification
The CYBLE-0130XX-00 module will be certified under the following RF certification standards at production release.
■
FCC: WAP3025
■
CE
■
IC: 7922A-3025
■
MIC: 203-JN0701
Safety Certification
The CYBLE-0130XX-00 module complies with the following safety regulations:
■
Underwriters Laboratories, Inc. (UL): Filing E331901
■
CSA
■
TUV
Environmental Conditions
Table 23 describes the operating and storage conditions for the Cypress BLE module.
Table 23. Environmental Conditions for CYBLE-0130XX-00
Description
Operating temperature
Operating humidity (relative, non-condensation)
Minimum Specification
Maximum Specification
30 °C
85 °C
5%
85%
–
3 °C/minute
–40 °C
85 °C
Storage temperature and humidity
–
85 °C at 85%
ESD: Module integrated into system Components[29]
–
15 kV Air
2.0 kV Contact
Thermal ramp rate
Storage temperature
ESD and EMI Protection
Exposed components require special attention to ESD and electromagnetic interference (EMI).
A grounded conductive layer inside the device enclosure is suggested for EMI and ESD performance. Any openings in the enclosure
near the module should be surrounded by a grounded conductive layer to provide ESD protection and a low-impedance path to ground.
Device Handling: Proper ESD protocol must be followed in manufacturing to ensure component reliability.
Note
29. This does not apply to the RF pins (ANT).
Document Number: 002-19200 Rev. **
Page 32 of 41
PRELIMINARY
CYBLE-013025-00
CYBLE-013030-00
Regulatory Information
FCC
FCC NOTICE:
The device CYBLE-0130XX-00 complies with Part 15 of the FCC Rules. The device meets the requirements for modular transmitter
approval as detailed in FCC public Notice DA00-1407.transmitter Operation is subject to the following two conditions: (1) This device
may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause
undesired operation.
CAUTION:
The FCC requires the user to be notified that any changes or modifications made to this device that are not expressly approved by
Cypress Semiconductor may void the user's authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions,ê may cause
harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
■
Reorient or relocate the receiving antenna.
■
Increase the separation between the equipment and receiver.
■
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
■
Consult the dealer or an experienced radio/TV technician for help
LABELING REQUIREMENTS:
The Original Equipment Manufacturer (OEM) must ensure that FCC labelling requirements are met. This includes a clearly visible
label on the outside of the OEM enclosure specifying the appropriate Cypress Semiconductor FCC identifier for this product as well
as the FCC Notice above. The FCC identifier is FCC ID: WAP3025.
In any case the end product must be labeled exterior with "Contains FCC ID: WAP3025"
ANTENNA WARNING:
This device is tested with a standard SMA connector and with the antennas listed below. When integrated in the OEMs product, these
fixed antennas require installation preventing end-users from replacing them with non-approved antennas. Any antenna not in the
following table must be tested to comply with FCC Section 15.203 for unique antenna connectors and Section 15.247 for emissions.
RF EXPOSURE:
To comply with FCC RF Exposure requirements, the Original Equipment Manufacturer (OEM) must ensure to install the approved
antenna in the previous.
The preceding statement must be included as a CAUTION statement in manuals, for products operating with the approved antennas
in Table 7 on page 13, to alert users on FCC RF Exposure compliance. Any notification to the end user of installation or removal
instructions about the integrated radio module is not allowed.
The radiated output power of CYBLE-0130XX-00 with the trace antenna is far below the FCC radio frequency exposure limits.
Nevertheless, use CYBLE-0130XX-00 in such a manner that minimizes the potential for human contact during normal operation.
End users may not be provided with the module installation instructions. OEM integrators and end users must be provided with
transmitter operating conditions for satisfying RF exposure compliance.
Document Number: 002-19200 Rev. **
Page 33 of 41
PRELIMINARY
CYBLE-013025-00
CYBLE-013030-00
Innovation, Science and Economic Development (ISED) Canada Certification
CYBLE-0130XX-00 is licensed to meet the regulatory requirements of Innovation, Science and Economic Development (ISED)
Canada,
License: IC: 7922A-3025
Manufacturers of mobile, fixed or portable devices incorporating this module are advised to clarify any regulatory questions and ensure
compliance for SAR and/or RF exposure limits. Users can obtain Canadian information on RF exposure and compliance from
www.ic.gc.ca.
This device has been designed to operate with the antennas listed in Table 7 on page 13, having a maximum gain of -0.5 dBi. Antennas
not included in this list or having a gain greater than 0.5 dBi are strictly prohibited for use with this device. The required antenna
impedance is 50 ohms. The antenna used for this transmitter must not be co-located or operating in conjunction with any other antenna
or transmitter.
ISED NOTICE:
The device CYBLE-0130XX-00 including the built-in trace antenna complies with Canada RSS-GEN Rules. The device meets the
requirements for modular transmitter approval as detailed in RSS-GEN. Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) This device must accept any interference received, including interference that
may cause undesired operation.
L'appareil CYBLE-0130XX-00, y compris l'antenne intégrée, est conforme aux Règles RSS-GEN de Canada. L'appareil répond aux
exigences d'approbation de l'émetteur modulaire tel que décrit dans RSS-GEN. L'opération est soumise aux deux conditions
suivantes: (1) Cet appareil ne doit pas causer d'interférences nuisibles, et (2) Cet appareil doit accepter toute interférence reçue, y
compris les interférences pouvant entraîner un fonctionnement indésirable.
ISED INTERFERENCE STATEMENT FOR CANADA
This device complies with Innovation, Science and Economic Development (ISED) Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any
interference, including interference that may cause undesired operation of the device.
Cet appareil est conforme à la norme sur l'innovation, la science et le développement économique (ISED) norme RSS exempte de
licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur
de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le
fonctionnement.
ISED RADIATION EXPOSURE STATEMENT FOR CANADA
This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment.
Cet équipement est conforme aux limites d'exposition aux radiations ISED prévues pour un environnement incontrôlé.
LABELING REQUIREMENTS:
The Original Equipment Manufacturer (OEM) must ensure that ISED labelling requirements are met. This includes a clearly visible
label on the outside of the OEM enclosure specifying the appropriate Cypress Semiconductor IC identifier for this product as well as
the ISED Notices above. The IC identifier is 7922A-3025. In any case, the end product must be labeled in its exterior with "Contains
IC: 7922A-3025"
Document Number: 002-19200 Rev. **
Page 34 of 41
PRELIMINARY
CYBLE-013025-00
CYBLE-013030-00
European Declaration of Conformity
Hereby, Cypress Semiconductor declares that the Bluetooth module CYBLE-0130XX-00 complies with the essential requirements
and other relevant provisions of Directive 2014. As a result of the conformity assessment procedure described in Annex III of the
Directive 2014, the end-customer equipment should be labeled as follows:
All versions of the CYBLE-0130XX-00 in the specified reference design can be used in the following countries: Austria, Belgium,
Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, The Netherlands, the United Kingdom, Switzerland, and Norway.
MIC Japan
CYBLE-0130XX-00 is certified as a module with certification number 203-JN0701. End products that integrate CYBLE-0130XX-00 do
not need additional MIC Japan certification for the end product.
End product can display the certification label of the embedded module.
Document Number: 002-19200 Rev. **
Page 35 of 41
CYBLE-013025-00
CYBLE-013030-00
PRELIMINARY
Packaging
Table 24. Solder Reflow Peak Temperature
Module Part Number
Package
CYBLE-0130XX-00
31-pad SMT
Maximum Peak Temperature Maximum Time at Peak Temperature No. of Cycles
260 °C
30 seconds
2
Table 25. Package Moisture Sensitivity Level (MSL), IPC/JEDEC J-STD-2
Module Part Number
Package
MSL
CYBLE-0130XX-00
31-pad SMT
MSL 3
The CYBLE-0130XX-00 is offered in tape and reel packaging. Figure 17 details the tape dimensions used for the CYBLE-0130XX-00.
Figure 17. CYBLE-0130XX-00 Tape Dimensions
Figure 18 details the orientation of the CYBLE-0130XX-00 in the tape as well as the direction for unreeling.
Figure 18. Component Orientation in Tape and Unreeling Direction
Document Number: 002-19200 Rev. **
Page 36 of 41
PRELIMINARY
CYBLE-013025-00
CYBLE-013030-00
Figure 19 details reel dimensions used for the CYBLE-0130XX-00.
Figure 19. Reel Dimensions
The CYBLE-0130XX-00 is designed to be used with pick-and-place equipment in an SMT manufacturing environment. The
center-of-mass for the CYBLE-0130XX-00 is detailed in Figure 20.
Figure 20. CYBLE-0130XX-00 Center of Mass
Document Number: 002-19200 Rev. **
Page 37 of 41
CYBLE-013025-00
CYBLE-013030-00
PRELIMINARY
Ordering Information
Table 26 lists the CYBLE-0130XX-00 part number and features. Table 27 lists the reel shipment quantities for the CYBLE-0130XX-00.
Table 26. Ordering Information
Part Number
CPU
Speed
(MHz)
CYBLE-013025-00
24
128
CYBLE-013030-00
24
–
Flash
RAM
Size (KB) Size (KB)
UART
BSC
(I2C)
PWM
Package
Packaging
60
Yes
Yes
4
31-SMT
Tape and Reel
60
Yes
Yes
4
31-SMT
Tape and Reel
Table 27. Tape and Reel Package Quantity and Minimum Order Amount
Description
Minimum Reel Quantity
Maximum Reel Quantity
Comments
Reel Quantity
500
500
Minimum Order Quantity (MOQ)
500
–
–
Order Increment (OI)
500
–
–
Ships in 500 unit reel quantities.
The CYBLE-0130XX-00 is offered in tape and reel packaging. The CYBLE-0130XX-00 ships in a reel size of 500.
For additional information and a complete list of Cypress Semiconductor BLE products, contact your local Cypress sales
representative. To locate the nearest Cypress office, visit our website.
U.S. Cypress Headquarters Address
U.S. Cypress Headquarter Contact Info
Cypress website address
Document Number: 002-19200 Rev. **
198 Champion Court, San Jose, CA 95134
(408) 943-2600
http://www.cypress.com
Page 38 of 41
CYBLE-013025-00
CYBLE-013030-00
PRELIMINARY
Acronyms
Document Conventions
Table 28. Acronyms Used in this Document
Units of Measure
Acronym
BLE
Description
Table 29. Units of Measure
Bluetooth Low Energy
Symbol
Unit of Measure
Bluetooth SIG Bluetooth Special Interest Group
°C
degree Celsius
CE
European Conformity
kV
kilovolt
CSA
Canadian Standards Association
mA
milliamperes
EMI
electromagnetic interference
mm
millimeters
ESD
electrostatic discharge
mV
millivolt
FCC
Federal Communications Commission
GPIO
general-purpose input/output
A
m
IC
Industry Canada
MHz
IDE
integrated design environment
GHz
gigahertz
KC
Korea Certification
V
volt
MIC
Ministry of Internal Affairs and Communications
(Japan)
PCB
printed circuit board
RX
receive
QDID
qualification design ID
SMT
surface-mount technology; a method for
producing electronic circuitry in which the
components are placed directly onto the surface
of PCBs
TCPWM
timer, counter, pulse width modulator (PWM)
TUV
Germany: Technischer Überwachungs-Verein
(Technical Inspection Association)
TX
transmit
Document Number: 002-19200 Rev. **
microamperes
micrometers
megahertz
Page 39 of 41
CYBLE-013025-00
CYBLE-013030-00
PRELIMINARY
Document History Page
Document Title: CYBLE-013025-00|CYBLE-013030-00 EZ-BLE™ WICED Module
Document Number: 002-19200
Revision
ECN
**
5764974
Orig. of Submission
Change
Date
DSO
Description of Change
06/08/2017 Preliminary datasheet for CYBLE-0130XX-00 module.
Document Number: 002-19200 Rev. **
Page 40 of 41
PRELIMINARY
CYBLE-013025-00
CYBLE-013030-00
Sales, Solutions, and Legal Information
Worldwide Sales and Design Support
Cypress maintains a worldwide network of offices, solution centers, manufacturer’s representatives, and distributors. To find the office
closest to you, visit us at Cypress Locations.
PSoC® Solutions
Products
ARM® Cortex® Microcontrollers
Automotive
cypress.com/arm
cypress.com/automotive
Clocks & Buffers
Interface
cypress.com/clocks
cypress.com/interface
Internet of Things
Memory
cypress.com/iot
cypress.com/memory
Microcontrollers
cypress.com/mcu
PSoC
cypress.com/psoc
Power Management ICs
Touch Sensing
USB Controllers
Wireless Connectivity
PSoC 1 | PSoC 3 | PSoC 4 | PSoC 5LP | PSoC 6
Cypress Developer Community
Forums | WICED IOT Forums | Projects | Video | Blogs |
Training | Components
Technical Support
cypress.com/support
cypress.com/pmic
cypress.com/touch
cypress.com/usb
cypress.com/wireless
© Cypress Semiconductor Corporation, 2017. This document is the property of Cypress Semiconductor Corporation and its subsidiaries, including Spansion LLC ("Cypress"). This document, including
any software or firmware included or referenced in this document ("Software"), is owned by Cypress under the intellectual property laws and treaties of the United States and other countries worldwide.
Cypress reserves all rights under such laws and treaties and does not, except as specifically stated in this paragraph, grant any license under its patents, copyrights, trademarks, or other intellectual
property rights. If the Software is not accompanied by a license agreement and you do not otherwise have a written agreement with Cypress governing the use of the Software, then Cypress hereby
grants you a personal, non-exclusive, nontransferable license (without the right to sublicense) (1) under its copyright rights in the Software (a) for Software provided in source code form, to modify and
reproduce the Software solely for use with Cypress hardware products, only internally within your organization, and (b) to distribute the Software in binary code form externally to end users (either
directly or indirectly through resellers and distributors), solely for use on Cypress hardware product units, and (2) under those claims of Cypress's patents that are infringed by the Software (as provided
by Cypress, unmodified) to make, use, distribute, and import the Software solely for use with Cypress hardware products. Any other use, reproduction, modification, translation, or compilation of the
Software is prohibited.
TO THE EXTENT PERMITTED BY APPLICABLE LAW, CYPRESS MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS DOCUMENT OR ANY SOFTWARE
OR ACCOMPANYING HARDWARE, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. To the extent
permitted by applicable law, Cypress reserves the right to make changes to this document without further notice. Cypress does not assume any liability arising out of the application or use of any
product or circuit described in this document. Any information provided in this document, including any sample design information or programming code, is provided only for reference purposes. It is
the responsibility of the user of this document to properly design, program, and test the functionality and safety of any application made of this information and any resulting product. Cypress products
are not designed, intended, or authorized for use as critical components in systems designed or intended for the operation of weapons, weapons systems, nuclear installations, life-support devices or
systems, other medical devices or systems (including resuscitation equipment and surgical implants), pollution control or hazardous substances management, or other uses where the failure of the
device or system could cause personal injury, death, or property damage ("Unintended Uses"). A critical component is any component of a device or system whose failure to perform can be reasonably
expected to cause the failure of the device or system, or to affect its safety or effectiveness. Cypress is not liable, in whole or in part, and you shall and hereby do release Cypress from any claim,
damage, or other liability arising from or related to all Unintended Uses of Cypress products. You shall indemnify and hold Cypress harmless from and against all claims, costs, damages, and other
liabilities, including claims for personal injury or death, arising from or related to any Unintended Uses of Cypress products.
Cypress, the Cypress logo, Spansion, the Spansion logo, and combinations thereof, WICED, PSoC, CapSense, EZ-USB, F-RAM, and Traveo are trademarks or registered trademarks of Cypress in
the United States and other countries. For a more complete list of Cypress trademarks, visit cypress.com. Other names and brands may be claimed as property of their respective owners.
Document Number: 002-19200 Rev. **
Revised June 8, 2017
Page 41 of 41
工商网监
湘ICP备2023018690号
