EVALM1CTE620N3TOBO1

AN2018-32 EVAL-M1-CTE620N3 User Manual EVAL-M1-CTE620N3 User Manual iMOTION™ Modular Application Design Kit About this document Scope and purpose This user manual provides an overview of the evaluation board EVAL-M1-CTE620N3 including its main features, key data, pin assignments and mechanical dimensions. EVAL-M1-CTE620N3 is an evaluation board as part of the iMOTION™ Modular Application Design Kit. This power board including a 3-phase CIPOS™ Tiny Intelligent Power Module (IPM) for motor drive application. In combination with the control board equipped with the M1 20pin interface connector such as EVAL-M1-101T, it features and demonstrates Infineon’s CIPOS™ Tiny IPM technology and Advanced Motion Control Engine (MCE 2.0) technology for permanent magnet motors drive over the full speed range. This evaluation board EVAL-M1-CTE620N3 was developed to support customers during their first steps designing applications with CIPOS™ Tiny IPM and running any permanent magnet motor via sensorless sinusoidal control. Intended audience This user manual is intended for all technical specialists who know motor control and high power electronics converter and this board is intended to be used under laboratory conditions. Table of contents About this document ....................................................................................................................... 1 Table of contents ............................................................................................................................ 1 1 Safety precautions ................................................................................................................. 3 2 Introduction .......................................................................................................................... 4 3 3.1 3.2 EVAL-M1-CTE620N3 main features............................................................................................ 6 EVAL-M1-CTE620N3 board specifications .............................................................................................. 7 Pin assignment ........................................................................................................................................ 9 4 Getting Started with EVAL-M1-CTE620N3 ................................................................................. 11 4.1 Setting up the system............................................................................................................................ 11 4.2 iMOTION™ development tools and software ....................................................................................... 13 4.2.1 MCEWizard setup overview .............................................................................................................. 13 4.2.2 MCEDesigner setup overview .......................................................................................................... 15 5 Hardware description of EVAL-M1-CTE620N3 ........................................................................... 17 5.1 Inverter section using CIPOS™ Tiny IPM ............................................................................................... 17 5.1.1 DC bus sensing and MCEWizard configuration ............................................................................... 18 5.1.2 Motor External Current feedback configuration and calculation .................................................. 19 5.1.3 Inverter Overcurrent protection and Motor Gatekill configuration ............................................... 21 5.2 Thermistor/NTC Characteristics and protection calculation .............................................................. 22 5.2.1 CIPOS™ Internal NTC – Thermistor Characteristics ........................................................................ 22 5.2.2 Overtemperature Hardware Protection Circuit .............................................................................. 23 5.2.3 NTC shutdown value calculation and configuration ...................................................................... 24 5.3 Auxiliary power supply .......................................................................................................................... 25 User Manual www.infineon.com Please read the Important Notice and Warnings at the end of this document page 1 of 37 Revision 1.0 2018-08-23 EVAL-M1-CTE620N3 User Manual iMOTION™ Modular Application Design Kit Table of contents 5.4 5.5 6 Schematics for EVAL-M1-CTE620N3 ..................................................................................................... 26 PCB Layout for EVAL-M1-CTE620N3 ..................................................................................................... 28 Reference ............................................................................................................................. 35 Revision history............................................................................................................................. 36 User Manual 2 of 37 Revision 1.0 2018-08-23 EVAL-M1-CTE620N3 User Manual iMOTION™ Modular Application Design Kit Safety precautions 1 Safety precautions In addition to the precautions listed throughout this manual, please read and understand the following statements regarding hazards associated with development systems. Table 1 Precautions Attention: The ground potential of the EVAL-M1-CTE620N3 system is biased to a negative DC bus voltage potential. When measuring voltage waveform by oscilloscope, the scope’s ground needs to be isolated. Failure to do so may result in personal injury or death and equipment damage. Attention: Only personnel familiar with the drive and associated machinery should plan or implement the installation, start-up and subsequent maintenance of the system. Failure to comply may result in personal injury and/or equipment damage. Attention: The surfaces of the drive may become hot, which may cause injury. Attention: EVAL-M1-CTE620N3 system contains parts and assemblies sensitive to Electrostatic Discharge (ESD). Electrostatic control precautions are required when installing, testing, servicing or repairing this assembly. Component damage may result if ESD control procedures are not followed. If you are not familiar with electrostatic control procedures, refer to applicable ESD protection handbooks and guidelines. Attention: A drive, incorrectly applied or installed, can result in component damage or reduction in product lifetime. Wiring or application errors such as under sizing the motor, supplying an incorrect or inadequate DC supply or excessive ambient temperatures may result in system malfunction. Attention: Remove or connect the control board from or to the power drive. Wait three minutes after removing power from the power drive to discharge the bus capacitors. Do not attempt to service the drive until the bus capacitors have discharged to zero. Failure to do so may result in personal injury or death. Attention: EVAL-M1-CTE620N3 system is shipped with packing materials that need to be removed prior to installation. Failure to remove all packing materials which are unnecessary for system installation may result in overheating or abnormal operating condition. User Manual 3 of 37 Revision 1.0 2018-08-23 EVAL-M1-CTE620N3 User Manual iMOTION™ Modular Application Design Kit Introduction 2 Introduction The EVAL-M1-CTE620N3 evaluation power board is a part of the iMOTION™ Modular Application Design Kit for motor drives (iMOTION™ MADK). In order to run a motor, the matching control board is required to interface this power board. The MADK platform is intended to use various power stages with different control boards. These boards can easily be interfaced through the 20-pin iMOTION™ MADK M1 such as Eval-M1-101Tconnector to control board. This board is equipped with 20-pin M1 connector and is intended for single motor control only. This evaluation board is designed to give Easy-to-use power stage based on the Infineon's CIPOS™ Tiny Inteligent Power Module (IPM). The board is equipped with all assembly groups for sensorless field oriented control (FOC). It provides a single-phase AC-connector, rectifier and 3-phase output for connecting the motor. The power stage also contains emitter shunts for current sensing and a voltage divider for DC-link voltage measurement. The EVAL-M1-CTE620N3 evaluation board has perfect compatibility, it is compatible with the DIP and SIP two kind of packaging form and compatible with the different level of power CIPOS™ Tiny IPM. For example, if you need to evaluate IM393-X6E/F, The evaluation board fully support to pin-to-pin assembly and power rating.but if you need to evaluate IM393-S6E/F，IM393-X6E/F or IM393-L6E/F Tiny IPM, you can only do function test evaluation and the power rating isn’t satisfied. The EVAL-M1-CTE620N3 evaluation board is available through regular Infineon distribution partners as well as on Infineon's website. The features of this board are described in the main features chapter of this document, whereas the remaining paragraphs provide information to enable the customers to copy, modify and qualify the design for production according to their own specific requirements. Environmental conditions were considered in the design of the EVAL-M1-CTE620N3, but it is not qualified regarding safety requirements or manufacturing and operation over the whole operating temperature range or lifetime. The boards provided by Infineon are subject to functional testing only. The block diagram of the EVAL-M1-CTE620N3 is depicted in Figure 1. This evaluation board includes an EMI filter and soft power up circuit, 20 pins iMOTION™ MADK-M1 interface connector, auxiliary power supply to provide 15V and 3.3V and the CIPOS™ Tiny IPM. CIPOSTM Tiny IM393-X6E Inverter Section 15V Power Supply HVIC PWM M RFE VTH Overcurrent and Overtemperature protection GK PWM Itrip 15V & 3.3V Neutral EMI Filter & Soft Power Up Circuit DCBsense Line I_Shunt+ 20 pin iMOTIONTM MADK-M1 connector I_Shunt- Figure 1 User Manual The Block Diagram of the EVAL-M1-CTE620N3 4 of 37 Revision 1.0 2018-08-23 EVAL-M1-CTE620N3 User Manual iMOTION™ Modular Application Design Kit Introduction The hardware circuit regarding overtemperature and overcurrent protection is also included in this power board. The sense connection to open emitter shunt resistor is connected to the 20 pins iMOTION™ MADK-M1 interface connector. This power board is compatible with 2 packages(DIP and SIP) of CIPOS™ Tiny IPMs that feature Integrated Power Hybrid IC with Open Emitter pins and built-in high precision temperature monitor and over-current protection feature, along with the short-circuit rated IGBTs and integrated under-voltage lockout function, deliver high level of protection and fail-safe operation. Evaluation boards are not subject to the same procedures as regular products regarding Returned Material Analysis (RMA), Process Change Notification (PCN) and Product Discontinuation (PD). Evaluation boards are intended to be used under laboratory conditions by technical specialists only. User Manual 5 of 37 Revision 1.0 2018-08-23 EVAL-M1-CTE620N3 User Manual iMOTION™ Modular Application Design Kit EVAL-M1-CTE620N3 main features 3 EVAL-M1-CTE620N3 main features EVAL-M1-CTE620N3 is an evaluation board for motor drive applications with 3 phase IPM. Combined in a kit with one of the available MADK control board options, it demonstrates Infineon’s motion control IC and IPM technology for motor drives. Main features of CIPOS™ Tiny IPM IM393-X6E are: • Integrated gate drivers and bootstrap function • Temperature monitor • Protection shutdown pin • Low VCE(on) Trench IGBT technology • Under voltage lockout for all channels • Matched propagation delay for all channels • 3.3V Schmitt-triggered input logic • Cross-conduction prevention logic • Isolation 2000VRMS min and CTI>600 • Recognized by UL(Pending) The evaluation board characteristics are: • Input voltage 160~265VAC • Maximum 1200W motor power output • Compatble with DIP and SIP • On board EMI filter • Current sensing with single shunt or leg shunt • Auxiliary power supply with 15V, 3.3V • Overcurrent protection • Overtemperature hardware protection • Sensing of DC-link voltage • Thermistor output • Fault diagnostic output • Measurement test-points compatible to standard oscilloscope probes • PCB is 121 mm × 120 mm and has two layers with 35μm copper each • RoHS complaint User Manual 6 of 37 Revision 1.0 2018-08-23 EVAL-M1-CTE620N3 User Manual iMOTION™ Modular Application Design Kit EVAL-M1-CTE620N3 main features 3.1 EVAL-M1-CTE620N3 board specifications Table 2 depicts the important specifications of the evaluation board EVAL-M1-CTE620N3. Table 2 EVAL-M1-CTE620N3 board specifications Parameters Input Voltage Values Conditions / comments 165 - 265 Vrms lower AC input, less motor power output 6.4Arms input 220 VAC, Ta=25°C, IM393 Output Power (3phases) 1200 W input 220VAC, fPWM=6 kHz, Ta=25°C, Th=80°C(Refer to figure 2 curve) Current per leg 6.8Arms input 220VAC , fPWM=6 kHz, Ta=25°C, Th=80°C Input current DC Bus Voltage Maximum DC bus voltage 420 V Minimum DC bus voltage 120 V Switching Frequency Inverter switching frequency fPWM Current feedback Inverter current sensing resistor RS3,RS4,RS5 Protections Output current trip level Temperature trip level On board power supply 15 V 3.3 V PCB characteristics Material Dimension System environment Ambient temperature 1 20 kHz (max) 30 mΩ 1 14.7 Apeak 100 °C Configured by changing pull up resistor R30. For controller board Eval-M1-101T 15 V ± 2 %, max. 500 mA 3.3 V ± 1 %, max. 300 mA Used for CIPOS™ IPM gate driver and LDO Supplying the 3.3V to the controller board and protection circuits FR4, 1.6mm thickness, 2 layers. 35 µm copper thickness 121 mm x 120 mm From 0 to 50°C Non-condensing, maximum RH of 95 % For iMOTION™ IC IMC1xx, there are three types of Gatekill Input Source (Refer to section 5.1.3 or control board user manual for detail). Please note that, if select comparator for Gatakill Input Source, the external Gatakill signal will be not used. And the leg I_Shunt will be compared by the internal comparator with the “Gatekill Comparator Reference” value set in MCEWizard only. User Manual 7 of 37 Revision 1.0 2018-08-23 EVAL-M1-CTE620N3 User Manual iMOTION™ Modular Application Design Kit EVAL-M1-CTE620N3 main features Figure 2 Show the relationship between Output Power and Heatsink Temperature. Figure 2 The relationship between Output Power and Heatsink Temperature Figure 3 points out the functional groups on the top side of the EVAL-M1-CTE620N3 evaluation board. 1 2 9 3 6 4 7 5 10 Figure 3 User Manual 1. J1 - AC Input connector 2. J3 - Motor phase connector 3. Relay/NTC and FUSE 4. EMI filter 5. Rectifier Bridge 6. J2 - 20 pin iMOTION™ MADKM1 interface connector for controller board 7. Current sensing shunt resistor RS3, RS4, RS5 8. CIPOS™ Tiny IPM U6 (DIP) 9. T1-Auxiliary power supply transfomer 10. Fan 8 Functional groups of the EVAL-M1-CTE620N3 evaluation board’s top side 8 of 37 Revision 1.0 2018-08-23 EVAL-M1-CTE620N3 User Manual iMOTION™ Modular Application Design Kit EVAL-M1-CTE620N3 main features Figure 4 points out the functional groups on the bottom side of the EVAL-M1-CTE620N3 evaluation board. 11. ICE5GR4780AG U1 12. Auxiliary power supply Current sensing shunt resistor RS1, RS2 13. IFX1117MEV33H U3 11 12 13 Figure 4 3.2 Functional groups of the EVAL-M1-CTE620N3 evaluation board’s bottom side Pin assignment General information about the connectors of the EVAL-M1-CTE620N3 evaluation board is reported. Table 3 includes the details of the AC input connector J1. Table 3 J1- AC Line connector S. No. Pin Details 1 Line AC line input 2 Neutral AC neutral input 3 Earth Earth ground Table 4 provides the pin assignments of the 20 pins iMOTION™ MADK-M1 interface connector J2. This connector is the interface to the controller board. Table 4 J2 - iMOTION™ MADK-M1 20 pin interface connector for controller board Pin Name Pin Name Connectors 1 PWMUH 3.3 V compatible logic input for high side gate driver-Phase U User Manual 9 of 37 Revision 1.0 2018-08-23 EVAL-M1-CTE620N3 User Manual iMOTION™ Modular Application Design Kit EVAL-M1-CTE620N3 main features 2 GND Ground 3 PWMUL 3.3 V compatible logic input for low side gate driver-Phase U 4 GND 4 GND Ground 5 PWMVH 3.3 V compatible logic input for high side gate driver-Phase V 6 +3.3V On board 3.3 V supply 7 PWMVL 3.3 V compatible logic input for low side gate driver-Phase V 8 +3.3V On board 3.3 V supply 9 PWMWH 3.3 V compatible logic input for high side gate driver-Phase W 10 I_U Positive Current sense output 11 PWMWL 3.3 V compatible logic input for low side gate driver-Phase W 12 I_U- Negative current sense output or Ground 13 GK Gate kill signal – active low when overcurrent is detected 14 DCBSense DC bus positive voltage, scaled in 0-3.3 V range by a voltage divider 15 VTH Thermistor Output 16 I_V Positive Current sense output 17 I_V- Negative current sense output or Ground 18 I_W Positive Current sense output 19 I_W- Negative current sense output or Ground 20 VCC 15 V Power Supply Table 5 provides the details of the motor side connector J2. Table 5 J2 - Motor side connector S. No. Pin Details 1 U Connected to motor phase U 2 V Connected to motor phase V 3 W Connected to motor phase W Table 6 provides the details of the Fan connector J4. Table 6 J4 – Fan Connector S. No. Pin Details 1 15V Connected to 15V 2 GND Connected to Ground User Manual 10 of 37 Revision 1.0 2018-08-23 EVAL-M1-CTE620N3 User Manual iMOTION™ Modular Application Design Kit Getting Started with EVAL-M1-CTE620N3 4 Getting Started with EVAL-M1-CTE620N3 In order to run the motor system, a combination of the iMOTION™ MADK power board (EVAL-M1-CTE620N3) and the matching MADK control board is required. The iMOTION™ Software Tools MCEDesigner and MCEWizard are also required in order to initialy setup the system, as well as to control and fine-tune the system performance to match users exact needs. This chapter provides more details on setting up the system and getting started with iMOTION™ MADK development platform. 4.1 Setting up the system After downloading and installing the iMOTION™ PC Tools (MCEWizard and MCEDesigner), following steps needs to be executed in order to run the motor. Refer to user manul for iMOTION™ MADK control board such as (EVALM1-101T), MCEWizard and MCEDesigner documentation for more information. Figure 5 shows the system connection using EVAL-M1-CTE620N3 and control board (used control board EVALM1-101T for example). Motor Phase Outputs AC Power Input PC-USB Connector Figure 5 System connection example using EVAL-M1-CTE620N3 and EVAL-M1-101T 1. Connect PC-USB connector on the on-board-debugger to the PC via USB cable. 2. Connect EVAL-M1-CTE620N3’s MADK M1 20-pin interface connector (J2) to control board (see Figure 5). 3. Get the latest “IMC101T-T038 MCE Software Package” available on www.infineon.com/imotion-software web page. (Infineon iMOTION™ control IC IMC101T-T038 is used for control board EVAL-M1-101T). 4. Connect motor phase outputs to the motor. 5. Use MCEWizard to enter the motor and evaluation board hardware parameters and click button “Export to Designer file (.txt)” to system drive parameters file which will be used by MCEDesigner. 6. Connect AC power to power input connector and power on system. 7. Open MCEDesigner and open MCEDesigner default configuration file (.irc) for IMC101T devices (IMC101T_xx.irc) by clicking “File” menu and select “Open” in the pull down list. 8. Import system drive parameters file (generated in step 5) into MCEDesigner by clicking “File” > “Import Drive Parameters”. Select “Update All” radio button. User Manual 11 of 37 Revision 1.0 2018-08-23 EVAL-M1-CTE620N3 User Manual iMOTION™ Modular Application Design Kit Getting Started with EVAL-M1-CTE620N3 9. Program the MCE Firmware and system parameters into the internal Flash memory of iMOTION™ IC by clicking “Tools > Programmer “in the pull down menu, and then clicking on the “Program Firmware and Parameter” radio button. See chapter MCEDesigner setup overview setion 4.2.2 for more details. If the latest version of MCE firmware is already programmed into the IMC101T-T038 IC, then programming firmware can be skipped by selecting “Program Parameters” radio button option. Finally click “Start” button to program firware and parameter (or parameters only when programming firmware was skipped). 10. Start the motor by clicking the green traffic light button in the control bar. User Manual 12 of 37 Revision 1.0 2018-08-23 EVAL-M1-CTE620N3 User Manual iMOTION™ Modular Application Design Kit Getting Started with EVAL-M1-CTE620N3 4.2 iMOTION™ development tools and software The iMOTION™ Development Tool installers for MCEDesigner and MCEWizard are available for download via Infineon iMOTIONTM website (http://www.infineon.com/imotion-software). All the available tools and software variants are listed there. On-board debugger uses the SEGGER J-Link’s driver for UART communication with IMC101T-T038. J-Link driver will be installed during the MCEDesigner installation. In case the driver is not installed properly, please go to SEGGER J-Link website to download and install the latest J-Link “Software and Documentation pack for Windows”. 4.2.1 MCEWizard setup overview After installing the MCEWizard, the shortcut for MCEWizard appears on the Windows desktop. Double click the shortcut to open the MCEWizard and configure the parameters for evaluation boards or motor. Figure 7 shows the “Welcome Page” for MCEWizard, where the MADK control board or power board can be selected through the pull-down list. Infineon keeps releasing new MADK controller and power boards. Therefore, it could happen that some of the newest power boards are not pre-configured in the MCEWizard tool and cannot be selected through the pull-down menu. In that case, the user should select any other power board (as similar as possible) and follow the MCEWizard setup steps by entering the parameter values which are specific to the chosen board. Make sure both “I have modified the circuit board” and “Enable advanced question” checkmarks are selected. Please refer to the User Manual of the corresponding power board for additional information. After selecting the MADK control and the power board, start the MCEWizard system setup procedure by clicking the “Next” button in the right bottom corner as shown in Figure 7. Figure 6 Welcome Page of MCEWizard iMOTION™ MADK system enables users to easily test different combination of control and power board with their motors. User should be familiar with the system level parameters which are related to the motor used. There are very limited numbers of parameters which are specific to the control board or power board hardware. Table 7 provides the MCEWizard setup overview for hardware related parameters. Similar tables will be User Manual 13 of 37 Revision 1.0 2018-08-23 EVAL-M1-CTE620N3 User Manual iMOTION™ Modular Application Design Kit Getting Started with EVAL-M1-CTE620N3 available in each power board’s User Manual. Combination of this table and the corresponding table of the power board provides enough information to setup the MADK-based motor drive system in shortest time. Table 7 MCEWizard setup overview table Page Parameter Value Comment Welcome Page Power Board selecting MADK power board name If no, select similar power board to modify Options Page Motor 1 Shunt Configuration 30mΩ Question 3 Controller Supply Voltage Refer to control board user manual Question 19 Max DC Bus Voltage 420V Question 23 DC Bus Sensing High Resistor 2MΩ Question 24 DC Bus Sensing Low Resistor Refer to control board user manual 13.3kΩ by default Question 54 NTC Temperature Shutdown value Calculated as the Section 5.2.3 Refer to the control board user manual Question 63 GateSense Low-Side Devices High is true Question 64 GateSense High-Side Devices High is true Question 69 Motor 1 Current Input Calculated as the Section 5.1.2 After all the MCEWizard questions are answered, the “Verify & Save Page” will be shown as in Figure 7 Figure 7 Verify and Save page for MCEWizard Click “Calculate” button and “Export to Designer File (.txt)” button to save the parameter file which will be used by the MCEDesigner in the next steps. User Manual 14 of 37 Revision 1.0 2018-08-23 EVAL-M1-CTE620N3 User Manual iMOTION™ Modular Application Design Kit Getting Started with EVAL-M1-CTE620N3 4.2.2 MCEDesigner setup overview After installing MCEDesigner installer, there is a shortcut for MCEDesigner on Windows desktop. Double click the shortcut to open MCEDesigner and then open “IMC101T_xx.irc” file as shown in Table 7. Figure 8 MCEDesigner’s Main Display for EVAL-M1-101T To program system drive parameters into IMC101T-T038, please click “Tools” menu and select “Programmer” in the pull down list. The pop-up window “Program IMC controller” will show up as in Figure 9. Click on the “Program Parameters” radio button (this is the default option), and then select the Drive System Parameter file created using MCEWizard by clicking on “Browse”. Finally, click on the “Start” button to program the parameter file into the IMC101T-T038 IC. Figure 9 User Manual “Program IMC Controller” pop-up window 15 of 37 Revision 1.0 2018-08-23 EVAL-M1-CTE620N3 User Manual iMOTION™ Modular Application Design Kit Getting Started with EVAL-M1-CTE620N3 After Drive System Parameter file has been programmed into IMC102 controller, and the motor drive system is powered, the MCEDesigner can be used to start/stop the motor, display motor current traces, change the motor speeds, modify drive parameters and many other functions. Please refer to the MCEDesigner documentation for more details. Note: On-board Debugger portion of EVAL-M1-101T is galvanically isolated from the controller portion and the attached power board. In order to program the parameters or firmware to the IMC101TT038 controller, the 3.3V DC voltage needs to be supplied to the controller portion of the EVAL-M1101T. This voltage can either be supplied by the power board (MADK power boards are designed to supply the 3.3V to the control board through M1 connector) or by feeding the 3.3V DC voltage to the control board through some of the available 3.3V access/test points if the power board is not attached to the EVAL-M1-101T control board. To program new firmware and Drive System Parameter into IMC101T-T038, please click “Tools” menu and select “Programmer” in the pull down list. The pop-up window “Program IMC controller” will show up as in Figure 10. Click on the “Program Firmware and Parameter” radio button, and select the Drive System Parameter file created using MCEWizard by clicking on the “Browse” button on the row of “Program Parameter File”, and then select the firmware file by clicking on the “Browse” button on the row of “Program Firmware File”. Finally, click on the “Start” button to program the parameter file into the IMC101T-T038 IC. Figure 10 Program Firmware and Parameter in “Program IMC Controller” pop-up window All latest firmware file for different type of iMOTIONTM control ICs are available for download via Infineon iMOTIONTM website (http://www.infineon.com/imotion-software). User Manual 16 of 37 Revision 1.0 2018-08-23 EVAL-M1-CTE620N3 User Manual iMOTION™ Modular Application Design Kit Hardware description of EVAL-M1-CTE620N3 5 Hardware description of EVAL-M1-CTE620N3 To meet individual customer requirements and make the EVAL-M1-CTE620N3 evaluation board a basis for development or modification, all necessary technical data like schematics, layout and components are included in this chapter. 5.1 Inverter section using CIPOS™ Tiny IPM The inverter section is also implemented using the CIPOS™ Tiny IPM as sketched in Figure 11. This advanced IPM is a combination of Infineon’s newest low VCE(on) Trench IGBT technology optimized for best trade-off between conduction and switching losses and the industry benchmark 3 phase high voltage, high speed driver (3.3V compatible) in a fully isolated thermally enhanced package. A built-in high precision temperature monitor and over-current protection feature, along with the short circuit rated IGBTs and integrated under-voltage lockout function, deliver high level of protection and fail-safe operation. Using a dual in line package with full transfer mold structure resolves isolation problems to heatsink. The three pairs of capacitors C20 and C25, C21 and C26, C22 and C27 are used as bootstrap capacitors to provide the necessary floating supply voltages VBS3, VBS2 and VBS1 respectively. +15VCC U6 1 V+ C20 0.1uF 25V C25 10uF 25V C21 0.1uF 25V C26 10uF 25V GND PWMVL PWMWH PWMWL GK VTH 1 UL 3 VH 5 VL 7 WH 9 WL 11 GK 13 VTH 15 I_UVW- 17 I_UVW- 19 UH GND UL GND VH +3.3V VL +3.3V WH I_U+ WL I_U- GK DCB VTH I_V+ I_V- I_W+ I_W- VCC 2 4 C15 0.1uF 16V 6 C17 0.1uF 16V C18 0.1uF 16V +3.3V 8 10 I_U+ 12 I_UVW- 14 C22 0.1uF 25V C27 10uF 25V I_V+ 18 I_W+ 18 HIN1(U) 19 HIN2(V) 20 HIN3(W) 21 LIN1(U) 22 LIN2(V) 23 LIN3(W) C24 CON MADK 20P +15VCC VTH VTH V V VTH C23 470pF 16V ITRIP ITRIP GND GK GK LED2 GREEN GND 1 GK R37 4.87Kohm 1/8W 1% +3.3V VS2 31 U 13 VCC U C29 1nF 16V 16 17 W_OUT J3 IM393-X6E V_OUT 1 2 3 Motor Output VS1 30 U_OUT VTH 14 VSS/COM 15 VSS/COM 1 R31 3Kohm 1/8W 5% VS3 C28 12 20 GND 32 GND +15VCC R29 0ohm 1/8W 5% W C31 0.1uF 630V C30 0.1uF 630V 9 VS1(U) 10 VB1(U) W UH VH WH UL VL WL PWMUH PWMVH PWMWH PWMUL PWMVL PWMWL DCBSense 16 V+ 33 VRW VRV ITRIP VRU 29 I_W+ RS3 30mohm 3W 1% 28 I_V+ RS4 30mohm 3W 1% 27 I_U+ RS5 30mohm 3W 1% RFE 24 VRW 25 VRV 26 VRU GND I_U+ PWMUL PWMVH UH 35 1 GND PWMUH DCBUS V+ 6 VS2(V) 7 VB2(V) 1 J2 3 VS3(W) 4 VB3(W) I_V+ Fan_CON 1 2 1 I_W+ J4 +3.3V GND R28 1Kohm 1/8W 5% ITRIP 2 1 GND C13 DNI ITRIP: [(3.3V * 1/ 11)+0.12+0.02] / 0.03= 14.7A peak GND User Manual LM397 1 R33 1Kohm 1/8W 1% 3 R32 1Kohm 1/8W 1% 5 U5 4 ITRIP Figure 11 R30 10Kohm 1/8W 1% C16 C19 4700pF 16V 4700pF 16V C14 +15VCC 10uF 16V GND I_UVWR36 1Kohm 1/8W 1% D8 BAT60A GND I_W+ R34 1Kohm 1/8W 1% D9 BAT60A I_V+ R35 1Kohm 1/8W 1% D10 BAT60A I_U+ RJ1 0ohm 1/2W 1% I_V+ RJ2 0ohm 1/2W 1% I_U+ I_W+ I_W+ I_V+ I_U+ I_V+ If single shunt config is used, remove both RS3 and RS4, while insert RJ1=RJ2= 0ohm Schematic of the 3-phase inverter section using CIPOS™ Tiny IPM on EVAL-M1-CTE620N3 17 of 37 Revision 1.0 2018-08-23 EVAL-M1-CTE620N3 User Manual iMOTION™ Modular Application Design Kit Hardware description of EVAL-M1-CTE620N3 5.1.1 DC bus sensing and MCEWizard configuration DCBsense C3 DNI GND R7 DNI R8 500Kohm 1/8W 1% 500Kohm 1/8W 1% R6 500Kohm 1/8W 1% R5 500Kohm 1/8W 1% R4 1 DCBUS Pin 14 and pin 26 of connector J2 provide access to the DC-link voltage DCBsense. Three possible feedback cases are associated with these pins. Figure 12 provides the DC bus sense resistor details. By default, the resistor R7 is not mounted on EVAL-M1-CTE620N3. There must be a pull-down resistor mounted on the corresponding controller board. Figure 12 DC bus sense resistor on EVAL-M1-CTE620N3 evaluation board If a pull down resistor of 13.3 kΩ referred to ground is inserted either on the EVAL-M1-CTE620N3 evaluation board or on the control board, the DCBSense voltage results in the range of 0 to 3.3 V on the pin reflecting a DC bus voltage range of 0 to 420 V.If a pull down resistor of 13.3 kΩ is inserted on both, EVAL-M1-CTE620N3 evaluation board and on the control card, the DCBSense results scale to 0-1.65 V. No safety issue occurs. If no feedback is desired on the DCBSense pin, R4, R5, R6 or R8 should be removed to avoid high voltage on the connector. The high side resistors R4, R5, R6 and R8 for the DC bus sensing resistor divider on the controller board EVALM1-CTE620N3 are 2000kΩ, and should be configured in MCEWizard as shown in Figure 13. For the low side resistor value, please refer to the User Manual of the corresponding control board. User Manual 18 of 37 Revision 1.0 2018-08-23 EVAL-M1-CTE620N3 User Manual iMOTION™ Modular Application Design Kit Hardware description of EVAL-M1-CTE620N3 Figure 13 5.1.2 DC bus sensing configuration in MCEWizard Motor External Current feedback configuration and calculation The current input value is product of the shunt resistance in milliohms and gain of External current sense amplifier for EVAL-M1-101T as shown in Figure 14. Figure 14 Current shunt feedback and sample timing for EVAL-M1-101T The External Amplifier Gain circuit can be found in the schematics or User Manual for the control board (For example, EVAL-M1-101T see Figure 15). User Manual 19 of 37 Revision 1.0 2018-08-23 EVAL-M1-CTE620N3 User Manual iMOTION™ Modular Application Design Kit Hardware description of EVAL-M1-CTE620N3 Figure 15 depicts IU+ current feedback sensing circuity on EVAL-M1-101T evaluation board. Please note that the default external amplification gain is less than 1 for current sense in this evaluation board. +3.3V Current shunt resistor on power board Ish Figure 15 R6 10k, 1% R8 V1 100R iMOTION Controller V2 6 IU C15 R7 2k, 1% 220pF IU+ Rsh The part of Current feedback on the EVAL-M1-101T evaluation board Based on the principle of Kirchhoff's voltage law, ≈ ≈( − ∗ )∗ + + = ∗ + = = + 5 6 + + ∗ Based on this calculation, the current input for the MADK combination of EVAL-M1-101T and EVAL-M1CTE620N3 is 25mV/A. Please use same procedure to calculate the current input for other combinations of MADK boards and enter it into MCEWizard as shown in Figure 16. Figure 16 User Manual Current feedback configuration in MCEWizard for EVAL-M1-101T and EVAL-M1-CTE620N3 20 of 37 Revision 1.0 2018-08-23 EVAL-M1-CTE620N3 User Manual iMOTION™ Modular Application Design Kit Hardware description of EVAL-M1-CTE620N3 5.1.3 Inverter Overcurrent protection and Motor Gatekill configuration Figure 17 displays the overcurrent protection circuitry. The current sensing signal I_Shunt is connected to ITRIP via through the comparator U5, and ITRIP is filtered through capacitor C23. +3.3V R28 1Kohm 1/8W 5% ITRIP 2 1 C13 DNI GND LM397 1 R33 1Kohm 1/8W 1% 3 R32 1Kohm 1/8W 1% I_UVW- 5 U5 4 ITRIP Figure 17 R30 10Kohm 1/8W 1% GND C16 C19 4700pF 16V 4700pF 16V +15VCC C14 10uF 16V GND GND R36 1Kohm 1/8W 1% D8 BAT60A I_W+ R34 1Kohm 1/8W 1% D9 BAT60A I_V+ R35 1Kohm 1/8W 1% D10 BAT60A I_U+ I_W+ I_V+ I_U+ Overcurrent protection circuit on the EVAL-M1-CTE620N3 evaluation board The typical value of ITRIP positive going threshold VIT, TH+ is 300mV. So the inverter output peak current is about 14.7Apeak. = ∗ 33 + 30 + 33 / / + If the motor peak current larger than the setting value Itrip for more than ITRIP Input filter time, RFE will be trigger low which is mean that the signal Gatekill is active. For iMOTION™ IMC1xx control IC, there are three types of Gatekill Input Source (as shown in Figure 18). For Gatekill Input Source configured Gatekill-Pin or Both, iMOTION™ control IC will stop the Motor when the signal GateKill is active. But please note that, if select comparator for Gatakill Input Source, the external Gatakill signal will be not used. And the current sensing signal I_Shunt will be compared by the internal comparator with the “Gatekill Comparator Reference” value set in MCEWizard only. Figure 18 User Manual Gatekill configuration in MCEWizard for EVAL-M1-101T 21 of 37 Revision 1.0 2018-08-23 EVAL-M1-CTE620N3 User Manual iMOTION™ Modular Application Design Kit Hardware description of EVAL-M1-CTE620N3 5.2 Thermistor/NTC Characteristics and protection calculation This board provides Thermistor/NTC output on pin 15 of the 20 pins connector J2. Temperatures can be calculated by resistor measurement. 5.2.1 CIPOS™ Internal NTC – Thermistor Characteristics The thermistor characteristics for CIPOS™ Tiny IPM with build in NTC are listed as summarized in Table 8. Table 8 CIPOS™ Internal NTC – Thermistor Characteristics Description Condition Symbol Resistor TNTC = 25°C Resistor TNTC = 125°C B-constant of NTC Temperature Range User Manual Value Unit min typ max RNTC 44.65 47 49.35 kΩ RNTC 1.27 1.41 1.56 kΩ B(25/100) 3989 4050 4111 K -40 - 125 ℃ 22 of 37 Revision 1.0 2018-08-23 EVAL-M1-CTE620N3 User Manual iMOTION™ Modular Application Design Kit Hardware description of EVAL-M1-CTE620N3 The VTH pin of CIPOS™-Modules provides direct access to the NTC, which is referenced to VSS. An external pullup resistor connected to +3.3V ensures that the resulting voltage can be directly connected to the microcontroller. Figure 19 Thermistor readout vs.temperature(with 4.7kohm Rext pull-down resistor)and typical thermistor resistance values vs.temperature table 5.2.2 Overtemperature Hardware Protection Circuit In this evaluation design kits EVAL-M1-CTE620N3 and EVAL-M1-101T, the VTH pin is directly connected to the VTH pin for controller IC IMC101T. +3.3V NTC 7 VTH IM393-X6E 1 R2 4.87Kohm 1/8W 1% IMC-101T TP10 VTH 13 VTH C9 0.01uF 16V Figure 20 User Manual Overtemperature protection circuit schematic for EVAL-M1-CTE620N3 and EVAL-M1-101T 23 of 37 Revision 1.0 2018-08-23 EVAL-M1-CTE620N3 User Manual iMOTION™ Modular Application Design Kit Hardware description of EVAL-M1-CTE620N3 5.2.3 NTC shutdown value calculation and configuration External NTC Temperature shutdown value can be calculated as shown below and configured in MCEWizard as shown in Figure 21. For pull-up resistor on evaluation control board, please refer to the control board’s User Manual. For example, for EVAL-M1-101T, the pull-up resistor on the control board is 4.87kΩ. The value of resistors REXT and RTHERM on IM393 are 4.87kΩ and 2.902kΩ (see Figure 20). The typical value of RNTC at 100°C is 2.902kΩ for IPM IM393 which is used in EVAL-M1-CTE620N3. ℎ = @ @ + = ℎ If the setting temperature is 100°C, the shutdown value should be 1.23V. If the setting temperature is 85°C, the shutdown value should be 1.62V. Figure 21 User Manual External temperature sense input configuration in MCEWizard 24 of 37 Revision 1.0 2018-08-23 EVAL-M1-CTE620N3 User Manual iMOTION™ Modular Application Design Kit Hardware description of EVAL-M1-CTE620N3 5.3 Auxiliary power supply Figure 22 depicts the schematic of the auxiliary power supply for the EVAL-M1-CTE620N3 board. The circuit includes the latest CoolSET 5 of Infineon and flyback toplogy, directly output 15V and 6V. VCC is connected to the gate drivers inside the CIPOS™ IPM. DNI R19 DNI VCC 1 C8 DCP D3 +15V 6 R17 C6 R9 3M 1/4W 1nF 630V R13 D2 15M 1/4W US1M-E3/61T-1A/1000V 7 D4 BYS10-45-E3/TR3-1.5A/45V 9 3 U3 IFX1117-ME V33 +6V Vin C14 ECAP 25V 330uF 8*3.5 3.3V SGND Vout 3M 1/4W 4 R14 C9 C10 C13 C16 10 ECAP 16V 220uF 8*3.5 15M 1/4W C5 +3.3V TP6 GND R10 VCC TP5 2.7uH 4A C11 ECAP 25V 330uF 8*3.5 SS3H10-E3/9AT-3A/100V 68k 1/4W 2 1 1 T1 L2 10uF 16V ECAP 16V 100uF 8*3.5 ECAP 16V 100uF 5*2 SGND R16 5 R11 R15 3M 1/4W 15M 1/4W D1 EE13-10P DIO FRD 700mA 200V 4R7 1/10W VCC U1 9 10 GND 11 12 C4 0.1uF 25V Drain Drain NC CS GATE FB VCC VERR GND VIN 6 5 GND RS1 5.1R 1/4W 4 R22 0ohm 1/8W 1% 1.5Kohm 1/8W 1% RS2 5.1R1/4W 3 2 1 U2 SFH617A-3X007 C7 R18 2.2nF 16V 510Kohm 1/8W 1% ICE5GR4780AG ZD1 R24 48.7K 1/10W 1% R20 R23 22K 1/10W R21 MMSZ5251B-7-F-22V 500mW C12 1nF 16V 2 1000pF 16V Drain 3 R12 58.3Kohm 1/4W 1% C3 Drain 1 8 4 7 C15 220nF 16V 820R 1/10W 1% U4 GND TL431DBZR R25 9.76K 1/10W 1% SGND Figure 22 Power supply section of the EVAL-M1-CTE620N3 evaluation board The linear voltage regulator IFX1117ME V33 generates 3.3 V from 6 V power supply VCC. The 3.3 V power supply is used in the inverter external overcurrent comparator circuit and overtemperature hardware protection circuit. Both VCC and 3.3 V are also present on the 20 pins iMOTION™ MADK-M1 interface connector J2 to power circuitry on the control board. User Manual 25 of 37 Revision 1.0 2018-08-23 EVAL-M1-CTE620N3 User Manual iMOTION™ Modular Application Design Kit Hardware description of EVAL-M1-CTE620N3 5.4 Schematics for EVAL-M1-CTE620N3 The AC linear setion schematic for EVAL-M1-CTE620N3 is provided in Figure 23. F1 1 DCBUS RT1 10A 250V DCBUS J1 BR1 NTC/5D-20 BR CY2 3300pF 250VAC 1Mohm 1/2W 5% 4 2 CX1 0.47uF 275VAC R1 1 3 L1 N 500Kohm 1/8W 1% E1 CX2 0.47uF 275VAC E2 470uF 400V 35*35 EARTH EARTH 470uF 400V 35*35 500Kohm 1/8W 1% 8121-RC-2mH 10A EARTH 3 R10 100Kohm 1/2W 5% R5 CY1 3300pF 250VAC AC input CON 4 R9 100Kohm 1/2W 5% R4 L GND R6 LED1 RED 500Kohm 1/8W 1% RLY1 +15VCC D1 D2 1 BAV19W R8 500Kohm 1/8W 1% G4A-1A-P-E-DC12-20A BAV19W 2 D3 DCBsense BAV19W C3 DNI GND GND 1 3.3Kohm 1/8W 5% C1 GND 1 47ohm 1/8W 5% R2 1 R3 R7 DNI 10uF 25V GND Q1 FMMT493TA C2 GND 4.7uF 25V Figure 23 SGND AC Linear Section Schematics for EVAL-M1-CTE620N3 The Inverter setion schematic for EVAL-M1-CTE620N3 is provided in Figure 24. +15VCC U6 1 V+ GND PWMUL PWMVH PWMVL PWMWH PWMWL GK VTH UH 1 UL 3 VH 5 VL 7 WH 9 WL 11 GK 13 VTH 15 I_UVW- 17 I_UVW- 19 UH GND UL GND VH +3.3V VL +3.3V WH I_U+ WL I_U- GK DCB VTH I_V+ I_V- I_W+ I_W- VCC C26 10uF 25V C21 0.1uF 25V 2 4 C15 0.1uF 16V 6 C17 0.1uF 16V C18 0.1uF 16V +3.3V 8 10 I_U+ 12 I_UVW- 14 C22 0.1uF 25V C27 10uF 25V I_V+ 18 I_W+ 18 HIN1(U) 19 HIN2(V) 20 HIN3(W) 21 LIN1(U) 22 LIN2(V) 23 LIN3(W) C24 W 20 +15VCC VTH VTH VTH C23 470pF 16V ITRIP ITRIP GND GK GK LED2 GREEN GND 1 GK R37 4.87Kohm 1/8W 1% +3.3V GND VS3 32 V V VS2 31 U 13 VCC U C29 1nF 16V 16 17 W_OUT J3 IM393-X6E V_OUT 1 2 3 Motor Output VS1 30 U_OUT VTH 14 VSS/COM 15 VSS/COM 1 R31 3Kohm 1/8W 5% C31 0.1uF 630V C30 0.1uF 630V C28 12 CON MADK 20P 33 9 VS1(U) 10 VB1(U) GND +15VCC R29 0ohm 1/8W 5% V+ 35 W UH VH WH UL VL WL PWMUH PWMVH PWMWH PWMUL PWMVL PWMWL DCBSense 16 DCBUS V+ 6 VS2(V) 7 VB2(V) VRW VRV ITRIP VRU 29 I_W+ RS3 30mohm 3W 1% 28 I_V+ RS4 30mohm 3W 1% 27 I_U+ RS5 30mohm 3W 1% RFE 24 VRW 25 VRV 26 VRU GND I_U+ J2 PWMUH 3 VS3(W) 4 VB3(W) 1 GND I_V+ Fan_CON 1 C25 10uF 25V C20 0.1uF 25V 1 2 1 I_W+ J4 +3.3V GND R28 1Kohm 1/8W 5% ITRIP 2 1 GND C13 DNI ITRIP: [(3.3V * 1/ 11)+0.12+0.02] / 0.03= 14.7A peak GND User Manual LM397 1 R33 1Kohm 1/8W 1% 3 R32 1Kohm 1/8W 1% 5 U5 4 ITRIP Figure 24 R30 10Kohm 1/8W 1% C16 C19 4700pF 16V 4700pF 16V C14 +15VCC 10uF 16V GND I_UVW- GND R36 1Kohm 1/8W 1% D8 BAT60A I_W+ R34 1Kohm 1/8W 1% D9 BAT60A I_V+ R35 1Kohm 1/8W 1% D10 BAT60A I_U+ RJ1 0ohm 1/2W 1% I_V+ RJ2 0ohm 1/2W 1% I_U+ I_W+ I_W+ I_V+ I_U+ I_V+ If single shunt config is used, remove both RS3 and RS4, while insert RJ1=RJ2= 0ohm Inverter Section Schematics for EVAL-M1-CTE620N3 26 of 37 Revision 1.0 2018-08-23 EVAL-M1-CTE620N3 User Manual iMOTION™ Modular Application Design Kit Hardware description of EVAL-M1-CTE620N3 The Auxiliary Power Supply setion schematic for EVAL-M1-CTE620N3 is provided in Figure 25. DNI R19 DNI VCC 1 C8 DCP D3 +15V 6 R17 C6 R9 R13 3M 1/4W 15M 1/4W 1nF 630V D2 US1M-E3/61T-1A/1000V 7 D4 BYS10-45-E3/TR3-1.5A/45V 9 3 U3 IFX1117-ME V33 +6V Vin C14 ECAP 25V 330uF 8*3.5 3.3V SGND Vout R14 3M 1/4W 15M 1/4W 4 C9 C10 C13 C16 10 ECAP 16V 220uF 8*3.5 C5 +3.3V TP6 GND R10 VCC TP5 2.7uH 4A C11 ECAP 25V 330uF 8*3.5 SS3H10-E3/9AT-3A/100V 68k 1/4W 2 1 1 T1 L2 10uF 16V ECAP 16V 100uF 8*3.5 ECAP 16V 100uF 5*2 SGND R16 5 R11 R15 3M 1/4W 15M 1/4W D1 EE13-10P DIO FRD 700mA 200V 4R7 1/10W VCC U1 9 10 GND 11 12 C4 0.1uF 25V Drain NC CS GATE FB VCC VERR GND VIN 6 5 GND RS1 5.1R 1/4W 4 R22 0ohm 1/8W 1% 1.5Kohm 1/8W 1% RS2 5.1R1/4W 3 2 1 U2 SFH617A-3X007 C7 R18 2.2nF 16V 510Kohm 1/8W 1% ICE5GR4780AG ZD1 R24 48.7K 1/10W 1% R20 R23 22K 1/10W R21 MMSZ5251B-7-F-22V 500mW C12 1nF 16V 2 1000pF 16V Drain Drain 3 R12 58.3Kohm 1/4W 1% C3 Drain 1 8 4 7 C15 220nF 16V 820R 1/10W 1% U4 GND TL431DBZR R25 9.76K 1/10W 1% SGND Figure 25 User Manual Auxiliary Power Supply Section Schematics for EVAL-M1-CTE620N3 27 of 37 Revision 1.0 2018-08-23 EVAL-M1-CTE620N3 User Manual iMOTION™ Modular Application Design Kit Hardware description of EVAL-M1-CTE620N3 5.5 PCB Layout for EVAL-M1-CTE620N3 The layout of this board can be used for different voltage or power classes. The PCB has two electrical layers with 35µm copper by default and its size is 121 mm × 120 mm. The PCB board thickness is 1.6mm. Get in contact with our technical support team to get more detailed information and the latest Gerber-files. Figure 26 illustrates the top assembly print of the evaluation board. Figure 26 Top assembly print of the EVAL-M1-CTE620N3 evaluation board Figure 27 depicts the bottom assembly print of the evaluation board. User Manual 28 of 37 Revision 1.0 2018-08-23 EVAL-M1-CTE620N3 User Manual iMOTION™ Modular Application Design Kit Hardware description of EVAL-M1-CTE620N3 Figure 27 User Manual Bottom assembly print of the EVAL-M1-CTE620N3 evaluation board 29 of 37 Revision 1.0 2018-08-23 EVAL-M1-CTE620N3 User Manual iMOTION™ Modular Application Design Kit Hardware description of EVAL-M1-CTE620N3 The top layer routing of the PCB is provided in Figure 28. Figure 28 Top layer routing of the EVAL-M1-CTE620N3 User Manual 30 of 37 Revision 1.0 2018-08-23 EVAL-M1-CTE620N3 User Manual iMOTION™ Modular Application Design Kit Hardware description of EVAL-M1-CTE620N3 Figure 29 illustrates the bottom layer routing of the PCB. Figure 29 User Manual Bottom layer routing of the EVAL-M1-CTE620N3 31 of 37 Revision 1.0 2018-08-23 EVAL-M1-CTE620N3 User Manual iMOTION™ Modular Application Design Kit Hardware description of EVAL-M1-CTE620N3 Table 9 provides the complete bill of materials for the EVAL-M1-CTE620N3. Table 9 Bill of materials No. Qty Part description Designator Part number Manufacturer 1 2 ECAP ALUM 470μF 400V RADIAL E1,E2 LLG2G471MELC 30 Wurth Electronics Inc. 2 1 CAP CER 470pF 16V 0805 C23 885012207031 Wurth Electronics Inc. 3 1 CAP CER 1000pF 16V 0603 C4 885012206034 Wurth Electronics Inc. 4 9 CAP CER 0.1μF 25V 0805 C5,C20,C21,C22 ,C24,C32,C33,C 34,C38 885012207072 Wurth Electronics Inc. 5 1 ECAP ALUM 100μF 16V RADIAL E3 860010372006 Wurth Electronics Inc. 6 1 CAP CER 1nF 630V 1206 C6 885342208011 Wurth Electronics Inc. 7 1 CAP CER 2200pF 16V 0805 C7 885012207035 Wurth Electronics Inc. 8 1 CAP CER 4700pF 100V 1206 C8 885012208110 Wurth Electronics Inc. 9 1 ECAP ALUM 220μF 16V RADIAL E4 860080374009 Wurth Electronics Inc. 10 3 CAP CER 10μF 16V 0805 C9,C12,C14 885012107014 Wurth Electronics Inc. 11 2 ECAP ALUM 330μF 25V RADIAL E5, E7 860020474013 Wurth Electronics Inc. 12 1 CAP ALUM 100μF 16V RADIAL C13 860240374004 Wurth Electronics Inc. 13 1 CAP CER 220nF 16V 0603 C11 885012206048 Wurth Electronics Inc. 14 3 CAP CER 0.1μF 16V 0603 C15,C17,C18 885012206046 Wurth Electronics Inc. 15 2 CAP CER 4700pF 16V 0805 C16,C19 885012207037 Wurth Electronics Inc. 16 1 CAP CER 1μF 16V 0805 C27 885012207051 Wurth Electronics Inc. 17 1 CAP CER 470pF 16V 0805 C23 885012207031 Wurth Electronics Inc. 18 1 CAP CER 1nF 16V X7R 0805 C29 885012207033 Wurth Electronics Inc. 19 9 CAP CER 10μF 25V 0805 C1,C25,C26,C27 ,C28,C35,C36,C 37,C39 TMK212BBJ106 KG-T Taiyo Yuden 20 2 CAP CER 0.1uF 630V X7R 1812 C30,C31 C4532X7R2J104 K230KA TDK Corporation 21 2 CAP FILM 0.47μF 10% 275VAC RADIAL CX1,CX2 MKP275VAC474 PF JIMSON 22 2 CAP CER 3300pF 440VAC Y5U RADIAL CY1, CY2 ECK-ATS332ME Panasonic Electronic Components 23 1 RES SMD 1MΩ 5% 1/2W 2010 R1 RC2010JR071ML Yageo 24 1 RES SMD 3.3kΩ 5% 1/8W 0805 R2 RC0805FR073K3L Yageo 25 1 RES SMD 47Ω 5% 1/8W 0805 R3 RC0805FR074R7L Yageo 26 4 RES SMD 500kΩ 1% 1/8W 0805 R4,R5,R6,R8 RC0805FR07500KL Yageo 27 2 RES SMD 100kΩ 5% 1/2W 2010 R9,R10 RC2010JR- Yageo User Manual 32 of 37 Revision 1.0 2018-08-23 EVAL-M1-CTE620N3 User Manual iMOTION™ Modular Application Design Kit Hardware description of EVAL-M1-CTE620N3 No. Qty Part description Designator 28 3 RES SMD 3MΩ 5% 1/4W 1206 R11,R12,R13 RC1206JR073ML Yageo 29 1 RES SMD 65kΩ 5% 1/4W 1206 R14 RC1206FR0765KL Yageo 30 3 RES SMD 15MΩ 5% 1/4W 1206 R15,R16,R17 RC1206JR0715ML Yageo 31 1 RES SMD 4.7Ω 1% 1/8W 0805 R18 RC0805FR074R7L Yageo 32 1 RES SMD 68kΩ 5% 1/4W 1206 R19 RC1206FR0768KL Yageo 33 1 RES SMD 510kΩ 1% 1/8W 0805 R20 RC0805FR07510KL Yageo 34 1 RES SMD 510Ω 5% 1/4W 1206 R21 RC1206JR07510RL Yageo 35 2 RES SMD 0 Ω 5% 1/8W 0805 R22,R29 RC0805JR070RL Yageo 36 1 RES SMD 820Ω 1% 1/8W 0805 R23 RC0805JR07820RL Yageo 37 1 RES SMD 1.5kΩ 1% 1/8W 0805 R24 RC0805JR071K5L Yageo 38 1 RES SMD 22kΩ 5% 1/8W 0805 R25 RC0805JR0722KL Yageo 39 1 RES SMD 48.7kΩ 1% 1/8W 0805 R26 RC0805FR0748K7L Yageo 40 1 RES SMD 9.76kΩ 1% 1/8W 0805 R27 RC0805FR079K76L Yageo 41 6 RES SMD 1kΩ 1% 1/8W 0805 R28,R32,R33,R3 4,R35,R36 RC0805FR071KL Yageo 42 1 RES SMD 10kΩ 5% 1/8W 0805 R30 RC0805JR0710KL Yageo 43 1 RES SMD 3kΩ 1% 1/8W 0805 R31 RC0805FR073KL Yageo 44 1 RES SMD 4.87kΩ 1% 1/8W 0805 R37 RC0805FR074K87L Yageo 45 2 RES SMD 5.1Ω 1% 1/4W 1206 RS1, RS2 RC1206FR075R1L Yageo 46 3 RES SMD 0.03Ω 1% 2W 2512 wide RS3, RS4,RS5 FC4L64R030FER Ohmite 47 1 IC AUX Power PD-DSO-12 U1 ICE5GR4780AG Infineon Technologies 48 1 IC OptoCoupler U2 SFH617A-3X007 Vishay 49 1 IC REG LINEAR 3.3V 1A SOT223-4 U3 IFX1117MEV33H TMA1 Infineon Technologies 50 1 IC TL431DBZR U4 TL431DBZR Texas Instruments User Manual 33 of 37 Part number 07100KL Manufacturer Revision 1.0 2018-08-23 EVAL-M1-CTE620N3 User Manual iMOTION™ Modular Application Design Kit Hardware description of EVAL-M1-CTE620N3 No. Qty Part description Designator Part number Manufacturer 51 1 IC COMPARATOR VOLT SGL SOT U5 LM397 Texas Instruments 52 1 IC CIPOS Tiny Module U6/U7 IM393-X6E/F Infineon Technologies 53 1 DIODE ZENER 22V 500mW SOD123 ZD1 MMSZ525B-7-F Wurth Electronics Inc. 54 3 DIODE FRD 100V 250mA SOD-123 D1,D2,D3 BAV19W Vishay 55 1 DIODE FRD 200V 700mA SOD-123 D4 RF071MM2STR ROHM 56 1 DIODE FRD 1000V 1A DO241AC D5 US1M-E3/61T Vishay 57 1 DIODE Schottky 100V 3A DO214AB D6 SS3H10-E3/9AT Vishay 58 1 DIODE Schottky 45V 1.5A DO214AC D7 BYS10-45E3/TR3 Vishay 59 3 Diode Standard 10V 3A Surface Mount SOD323 D8, D9, D10 BAT60A Infineon Technologies 60 1 NTC thermistors for inrush RT1 NTC5D-20 Yuanlindianzi 61 1 RECT BRIDGE GPP 800V 15A GBJ BR1 GBJ1508-F Diodes Incorporated 62 1 FUSE CERAMIC 10A 250V Φ6X30 F1 RO58 /BS136210A Zhenghao Fuse Co. 63 1 Common Choke 8108-RC L1 JWMILLER_810 8 Bourns, Inc. 64 1 FIXED 2.2uH 2.5A SMD L2 WE-PD2-S Wurth Electronics Inc. 65 1 LED RED CLEAR 0805 SMD LED1 LTSTC171KRKT Lite-On Inc. 66 1 LED GREEN CLEAR 0805 SMD LED2 LTST-C171GKT Lite-On Inc. 67 2 CONN TERM BLOCK 3POS 9.52MM PCB J1, J3 1714984 Phoenix Contact 68 1 CONN RCPT .100" 20 PS DL R/A GOLD J2 SSW-110-02-SD-RA Samtec Inc. 69 CONN 2P2.54 J4 XH2.54 RISYM 70 DC FAN FAN KDE2405PHBS SUNON 71 Heatsink Heatsink 100*40*40MM - Transformer EE13-10P T1 EE13-10P - 72 1 User Manual 34 of 37 Revision 1.0 2018-08-23 EVAL-M1-CTE620N3 User Manual iMOTION™ Modular Application Design Kit Reference 6 Reference [1] Datasheet of Infineon CIPOS™ Tiny IPM IM393-X6E [2] AN2018-02 EVAL-M1-101T User manual [3] MCEWizard User Guide [4] MCEDesigner User Guide Note: User Manual All listed reference materials are available for download on Infineon’s website www.infineon.com/. All the iMOTION MADK evaluation board’s User Manuals are available at www.infineon.com/MADK All the CIPOS™ IPM’s Datasheets and documents are available at www.infineon.com/IPM. 35 of 37 Revision 1.0 2018-08-23 EVAL-M1-CTE620N3 User Manual iMOTION™ Modular Application Design Kit Reference Revision history Document version Date of release Description of changes 1.0 2018-08-27 First Release User Manual 36 of 37 Revision 1.0 2018-08-23 Trademarks All referenced product or service names and trademarks are the property of their respective owners. Edition 2018-08-23 Published by Infineon Technologies AG 81726 Munich, Germany © 2018 Infineon Technologies AG. All Rights Reserved. Do you have a question about this document? Email: erratum@infineon.com Document reference AN2018-32 IMPORTANT NOTICE The information contained in this application note is given as a hint for the implementation of the product only and shall in no event be regarded as a description or warranty of a certain functionality, condition or quality of the product. Before implementation of the product, the recipient of this application note must verify any function and other technical information given herein in the real application. Infineon Technologies hereby disclaims any and all warranties and liabilities of any kind (including without limitation warranties of non-infringement of intellectual property rights of any third party) with respect to any and all information given in this application note. The data contained in this document is exclusively intended for technically trained staff. It is the responsibility of customer’s technical departments to evaluate the suitability of the product for the intended application and the completeness of the product information given in this document with respect to such application. For further information on the product, technology, delivery terms and conditions and prices please contact your nearest Infineon Technologies office (www.infineon.com). WARNINGS Due to technical requirements products may contain dangerous substances. For information on the types in question please contact your nearest Infineon Technologies office. Except as otherwise explicitly approved by Infineon Technologies in a written document signed by authorized representatives of Infineon Technologies, Infineon Technologies’ products may not be used in any applications where a failure of the product or any consequences of the use thereof can reasonably be expected to result in personal injury.