IFS100V12PT4BOSA1

Technical Information MIPAQ™ serve IFS100V12PT4 preliminary data Key data Power module using IGBT4 technology in sixpack configuration. Isolated IGBT driver, protection and temperature sensor included. Topology B6I Rated semiconductor data 1200V, 100A Load type Inductive, resistive Typical applications Sensors and protection Interface IGBT Standards prepared by: PK approved by: KS Industrial drives, UPS, solar inverters, auxiliary inverters temperature, short circuit, signal transmission, UVLO for all power supplies Electrical, 5V-CMOS, Galvanic Isolation according to IEC61800-5-1 IEC61800-5-1, UL94, RoHS date of publication: 2012-05-25 revision: 2.1 Technical Information MIPAQ™ serve IFS100V12PT4 preliminary data Electrical data – power part min IGBT continuous DC collector current Ls = 30nH -40 < Tvj < 150°C 0 < IC turn off < 2*IC max Tcase = 100°C Tvj = Tvjop max IGBT collector-emitter voltage Tvj=25°C IGBT collector-emitter saturation voltage Diode repetitive peak reverse voltage Tvj =25°C @ IC=100A Tvj =150°C @ IC=100A UCEsat Tvj=25°C URRM Diode forward voltage Tvj =25°C @ IC=100A Tvj =150°C @ IC=100A UF Operating junction temperature IGBT and Diode Tvjop DC link voltage Turn on energy loss per pulse Turn off energy loss per pulse Reverse recovery energy typ UDC 850 V IC nom 100 A 1200 V UCES IGBT, UDC=600V, IC=100A Tvj=150°C, di/dt,= 1,8kA/µs IGBT, UDC=600V, IC=100A Tvj=150°C, du/dt = 3,6kV/µs Diode, UDC=600V, IF=100A Tvj=150°C, di/dt = 1,8kA/µs max 1,75 2,10 2,15 1200 1,70 1,65 2,15 150 V V V °C Eon 10,2 mJ Eoff 8,0 mJ Erec 8,0 mJ Electrical data – control part Auxiliary power supply: IGBT Gate (on X1) IGBT driver positive supply IGBT driver negative supply IGBT driver undervoltage lockout threshold IGBT driver undervoltage lockout hysteresis Logic power supply undervoltage lockout threshold Logic power supply undervoltage lockout hysteresis prepared by: PK approved by: KS typ max 13 16 18 V Voltage UGS P1,2,3,4 Current at fsw = 20kHz, UGSP1,2,3 = +15V, Tvj = 25°C IGS P1,2,3 14 mA IGS P4 26 mA Voltage UGS N1,2,3,4 -5 V Current @ fsw = 20kHz, UGSN = -8V, Tvj = 25°C |IGS N1,2,3| 13 mA |IGS N4| 18 mA For each channel UGS_UVLO 10,4 12,6 V For each channel UGS_UVLO_H 0,7 Auxiliary power supply: Logic (on X2) Logic power supply min Voltage ULS Current @ fsw = 20kHz, ULS = +5V ILS -10 V min typ max 4,5 5 5,5 V 55 mA 4,3 V ULS_UVLO 3,5 ULS_UVLO_H 0,3 date of publication: 2012-05-25 revision: 2.1 -8 V Technical Information MIPAQ™ serve IFS100V12PT4 preliminary data Driver logic input/output, protection and sensors (on X2) Digital input (IGBT turn-on/off and RESET) Digital temperature output Minimum pulse width Minimum dead time 5,5 V Low level voltage UIN_L -0,3 1,5 V Input current per input IIN 100 400 µA tmin RST1 40 ns tmin RST2 500 ns Open drain, internally pulled up, max. 10 mA URDYT, URDYB, UFLTT, UFLTB, UTMP Frequency depends on measured temperature Pulses counted in 100ms IGBT-turn-on signal (=high) on each channel @ UDC max Between TOP IGBT and BOT IGBT Each driver channel Short circuit protection Desaturation threshold. Shutdown when exceeded. Each channel Reaction time. Shutdown after short circuit was detected. Each channel 0 ULS V fTMP 0,2 18 kHz N 20 1800 tPW_min 1 µs tdead 1 µs fsw 0 UCE_desat Each channel tprop_delay Propagation delay deviation Between two channels tprop delay dev Isolation Management Logic to power side f=50Hz, t=1s Life parts to base plate F=50Hz, 1=1min Comparative tracking index prepared by: PK approved by: KS 9 20 kHz 9,5 V 8 µs 320 ns 15 min Isolation management designed for Creepage distance Under usage of screws according DIN7984 with flat head, SKS-5 spring washer, DIN125 flat washer 8,5 tdesat Propagation delay Clearance distance, including internal clearance DIN7984 with flat head, SKS-5 spring washer, DIN125 flat washer, max 3,5 Switching frequency Isolation test voltage typ UIN_H Minimum pulse width on /RST for ENABLE/SHUTDOWN Minimum pulse width on /RST for resetting /FLTBOT, /FLTTOP Digital output level min High level voltage ns ULine typ 480 max Visol 2,5 kVRMS Visol 2,5 kVRMS VRMS CTI 225 terminal – terminal (AC-DC, AC-AC, DC-DC) lcl1 11 mm power side – heat sink lcl2 11 mm Logic side - heatsink lcl3 4,5 mm Logic side - power side lcl4 8 mm terminal – terminal (AC-DC, AC-AC, DC-DC) lcr1 25 mm terminal – heat sink lcr2 20 mm Logic side - heatsink lcr3 8,5 mm Logic side - power side lcr4 8 mm date of publication: 2012-05-25 revision: 2.1 Technical Information MIPAQ™ serve IFS100V12PT4 preliminary data Environmental conditions min Storage temperature Tstg Operating ambient temperature fSW ≤ 20kHz Humidity no condensation Rel. H. typ max -40 +125 °C -40 +65 °C 5 85 % 1000 m Installation height Vibration according to IEC60721 12 g Shock according to IEC60721 10 g Protection degree IP00 Pollution degree 2 Terminal connection torque Screw M6 MM6 3,0 6,0 Nm Mounting torque Screw M5 MM5 3,0 6,0 Nm Dimensions length x width x height Weight Thermal data min 130 x 103 x 28,5 mm³ 419 g typ max Thermal resistance junction to case Each IGBT Rthjc_IGBT 0,3 K/W Thermal resistance junction to case Each Diode Rthjc_FWD 0,55 K/W Thermal resistance case to heatsink Complete module Rthch_Module 0,009 K/W Module Stray inductance module min LsCE Material of module baseplate prepared by: PK approved by: KS typ 20 Cu date of publication: 2012-05-25 revision: 2.1 max nH Technical Information MIPAQ™ serve IFS100V12PT4 preliminary data Output characteristic IGBT IC = f(U CE) @ U GSPx = 16V Output characteristic IGBT IC = f(U CE) @ Tvj = 150°C 200 200 …….. 180 --- Tv j = 150°C 180 _____ Tv j = 25°C 160 140 140 120 120 IC [A] IC [A] 160 UGSPx = 18V --- 100 UGSPx = 16V _____ UGSPx = 14V 100 80 80 60 60 40 40 20 20 0 0 0 0,5 1 1,5 UCE [V] 2 2,5 0 3 0,5 1 1,5 2 2,5 3 3,5 4 4,5 5 UCE [V] Switching losses IGBT Eon = f(IC), Eoff = f(IC) Switching losses diode Erec = f(IF) @ U CE = 600V, Tvj = 150°C UGSPx = 16V, U GSNx = -8V, Tvj = 150°C 12 28 11 --- 24 _____ Eof f 10 Eon 20 Erec 8 E [mJ] E [mJ] ____ 9 16 12 7 6 5 4 8 3 2 4 1 0 0 25 50 75 100 125 150 175 0 200 0 IC [A] Forward characteristic diode IF = f(U F) 50 75 100 IF [A] 125 150 175 200 Digital temperature output Number of pulses within 100ms 1000 200 180 --- Tv j = 150°C _____ Tv j = 25°C 160 900 800 140 700 120 600 1/100ms IF [A] 25 100 500 80 400 60 300 40 200 20 100 0 0 0 0,2 0,4 0,6 0,8 prepared by: PK approved by: KS 1 1,2 1,4 1,6 1,8 UF [V] 2 2,2 2,4 -40 -30 -20 date of publication: 2012-05-25 revision: 2.1 -10 0 10 20 30 40 50 TNTC [°C] 60 70 80 90 100 110 120 Technical Information MIPAQ™ serve IFS100V12PT4 preliminary data Mechanical drawing prepared by: PK approved by: KS date of publication: 2012-05-25 revision: 2.1 Technical Information MIPAQ™ serve IFS100V12PT4 preliminary data Circuit diagram MIPAQ™serve inside Connector X1 and X2 Datasheet value T2pos T2GND T2neg 8 7 9 UGS P2 = U(T2pos) – U(T2GND) UGS N2 = U(T2neg) – U(T2GND) T1pos T1GND T1neg 4 1 3 UGS P1 = U(T1pos) – U(T1GND) UGS N1 = U(T1neg) – U(T1GND) Bpos BGND Bneg 19 21 20 UGS P4 = U(Bpos) – U(BGND) UGS N4 = U(Bneg) – U(BGND) UGS P3 = U(T3pos) – U(T3GND) UGS N3 = U(T3neg) – U(T3GND) High voltage area in grey power supply for IGBT Gate Pin 14 13 15 Connector X1 T3pos T3GND T3neg Power connector NTC EiceDRIVER™ 16 6 UFLT_T = U(/FLTT) – U(GND) UFLT_B = U(/FLTB) – U(GND) /RST 3 TMP 10 GND GND GND GND GND GND GND GND GND 5 7 9 11 13 15 17 19 21 digital I/O and power supply for digital I/O circuit UTMP = U(TMP) – U(GND) W high voltage area Galvanic Isolation Further information Molex Microfit 22 pins Molex Milligrid 22 pins All information regarding connectors can be found in AN2009-07 prepared by: PK approved by: KS T1 V low voltage area X1: X2: B1 /FLTT /FLTB EiceDRIVER™ URDY_T = U(RDYT) – U(GND) URDY_B = U(RDYB) – U(GND) T2 14 8 B2 RDYT RDYB UIN_L = U(VINx) – U(GND) for low input signal IGBT turn-off U EiceDRIVER™ UIN_H = U(VINx) – U(GND) for high input signal IGBT turn-on T3 22 1 20 2 18 4 EiceDRIVER™ INT3 INB3 INT2 INB2 INT1 INB1 B3 ULS = U(VCC) – U(GND) EiceDRIVER™ 12 DC+ DC- EiceDRIVER™ Datasheet value VCC Connector X2 Pin EiceDRIVER™ HB1H date of publication: 2012-05-25 revision: 2.1 Technical Information MIPAQ™ serve IFS100V12PT4 preliminary data Nutzungsbedingungen Die in diesem Produktdatenblatt enthaltenen Daten sind ausschließlich für technisch geschultes Fachpersonal bestimmt. Die Beurteilung der Geeignetheit dieses Produktes für die von Ihnen anvisierte Anwendung sowie die Beurteilung der Vollständigkeit der bereitgestellten Produktdaten für diese Anwendung obliegt Ihnen bzw. Ihren technischen Abteilungen. In diesem Produktdatenblatt werden diejenigen Merkmale beschrieben, für die wir eine liefervertragliche Gewährleistung übernehmen. Eine solche Gewährleistung richtet sich ausschließlich nach Maßgabe der im jeweiligen Liefervertrag enthaltenen Bestimmungen. Garantien jeglicher Art werden für das Produkt und dessen Eigenschaften keinesfalls übernommen. Sollten Sie von uns Produktinformationen benötigen, die über den Inhalt dieses Produktdatenblatts hinausgehen und insbesondere eine spezifische Verwendung und den Einsatz dieses Produktes betreffen, setzen Sie sich bitte mit dem für Sie zuständigen Vertriebsbüro in Verbindung (siehe www.eupec.com, Vertrieb&Kontakt). Für Interessenten halten wir Application Notes bereit. Aufgrund der technischen Anforderungen könnte unser Produkt gesundheitsgefährdende Substanzen enthalten. Bei Rückfragen zu den in diesem Produkt jeweils enthaltenen Substanzen setzen Sie sich bitte ebenfalls mit dem für Sie zuständigen Vertriebsbüro in Verbindung. Sollten Sie beabsichtigen, das Produkt in gesundheits- oder lebensgefährdenden oder lebenserhaltenden Anwendungsbereichen einzusetzen, bitten wir um Mitteilung. Wir weisen darauf hin, dass wir für diese Fälle die gemeinsame Durchführung eines Risiko- und Qualitätsassessments; den Abschluss von speziellen Qualitätssicherungsvereinbarungen; die gemeinsame Einführung von Maßnahmen zu einer laufenden Produktbeobachtung dringend empfehlen und gegebenenfalls die Belieferung von der Umsetzung solcher Maßnahmen abhängig machen. Soweit erforderlich, bitten wir Sie, entsprechende Hinweise an Ihre Kunden zu geben. Inhaltliche Änderungen dieses Produktdatenblatts bleiben vorbehalten. Terms & Conditions of usage The data contained in this technical information is exclusively intended for technically trained staff. You and your technical departments will have to evaluate the suitability of the product for the intended application and the completeness of the product data with respect to such application. This product data sheet is describing the characteristics of this product for which a warranty is granted. Any such warranty is granted exclusively pursuant the terms and conditions of the supply agreement. There will be no guarantee of any kind for the product and its specifications. Should you require product information in excess of the data given in this product data sheet or which concerns the specific application of our product, please contact the sales office, which is responsible for you (see www.infineon.com, sales&contact). For those that are specifically interested we may provide application notes. Due to technical requirements our product may contain dangerous substances. For information on the types in question please contact the sales office, which is responsible for you. Should you intend to use the Product in health or live endangering or life support applications, please notify. Please note, that for any such applications we urgently recommend to perform joint Risk and Quality Assessments; the conclusion of Quality Agreements; to establish joint measures of an ongoing product survey, and that we may make delivery depended on the realization of any such measures. If and to the extent necessary, please forward equivalent notices to your customers. Changes of this product data sheet are reserved. Sicherheitshinweise Bevor Sie mit der Installation und dem Betrieb der Baugruppe beginnen, lesen Sie bitte sorgfältig alle Sicherheitshinweise und Warnungen. Safety Instructions Prior to installation and operation, all safety notices and warnings have to be carefully read. prepared by: PK approved by: KS date of publication: 2012-05-25 revision: 2.1