IRF3007STRLPBF

PD - 95494A IRF3007SPbF IRF3007LPbF Typical Applications l HEXFET® Power MOSFET Industrial Motor Drive Features l l l l l D Ultra Low On-Resistance 175°C Operating Temperature Fast Switching Repetitive Avalanche Allowed up to Tjmax Lead-Free VDSS = 75V RDS(on) = 0.0126Ω G ID = 62A S Description This design of HEXFET® Power MOSFETs utilizes the lastest processing techniques to achieve extremely low on-resistance per silicon area. Additional features of this HEXFET power MOSFET are a 175°C junction operating temperature, fast switching speed and improved repetitive avalanche rating. These combine to make this design an extremely efficient and reliable device for use in a wide variety of applications. Absolute Maximum Ratings D2Pak IRF3007SPbF TO-262 IRF3007LPbF Max. Units Parameter ID @ TC = 25°C ID @ TC = 100°C IDM PD @TC = 25°C VGS EAS EAS (6 sigma) IAR EAR TJ TSTG Continuous Drain Current, VGS @ 10V Continuous Drain Current, VGS @ 10V Pulsed Drain Current  Power Dissipation Linear Derating Factor Gate-to-Source Voltage Single Pulse Avalanche Energy‚ Single Pulse Avalanche Energy Tested Value‡ Avalanche Current Repetitive Avalanche Energy† Operating Junction and Storage Temperature Range Soldering Temperature, for 10 seconds 62 44 320 120 0.8 ± 20 290 946 See Fig.12a, 12b, 15, 16 A W W/°C V mJ A mJ -55 to + 175 °C 300 (1.6mm from case ) Thermal Resistance Parameter RθJC RθJA Junction-to-Case Junction-to-Ambient (PCB Mounted,steady state)** Typ. Max. Units ––– ––– 1.25 62 °C/W ** This is applied to D2Pak, when mounted on 1" square PCB ( FR-4 or G-10 Material ). For recommended footprint and soldering techniques refer to application note #AN-994. www.irf.com 1 07/23/10 IRF3007S/LPbF Electrical Characteristics @ TJ = 25°C (unless otherwise specified) RDS(on) VGS(th) gfs Parameter Drain-to-Source Breakdown Voltage Breakdown Voltage Temp. Coefficient Static Drain-to-Source On-Resistance Gate Threshold Voltage Forward Transconductance Qg Qgs Qgd td(on) tr td(off) tf Gate-to-Source Forward Leakage Gate-to-Source Reverse Leakage Total Gate Charge Gate-to-Source Charge Gate-to-Drain ("Miller") Charge Turn-On Delay Time Rise Time Turn-Off Delay Time Fall Time Min. 75 ––– ––– 2.0 180 ––– ––– ––– ––– ––– ––– ––– ––– ––– ––– ––– Typ. ––– 0.084 10.5 ––– ––– ––– ––– ––– ––– 89 21 30 12 80 55 49 IDSS Drain-to-Source Leakage Current LD Internal Drain Inductance ––– 4.5 LS Internal Source Inductance ––– 7.5 Ciss Coss Crss Coss Coss Coss eff. Input Capacitance Output Capacitance Reverse Transfer Capacitance Output Capacitance Output Capacitance Effective Output Capacitance … ––– ––– ––– ––– ––– ––– 3270 520 78 3500 340 640 V(BR)DSS ∆V(BR)DSS/∆TJ IGSS Max. Units Conditions ––– V VGS = 0V, ID = 250µA ––– V/°C Reference to 25°C, ID = 1mA 12.6 mΩ VGS = 10V, ID = 48A „ 4.0 V VDS = 10V, ID = 250µA ––– S VDS = 25V, ID = 48A 20 VDS = 75V, VGS = 0V µA 250 VDS = 60V, VGS = 0V, TJ = 150°C 200 VGS = 20V nA -200 VGS = -20V 130 ID = 48A 32 nC VDS = 60V 45 VGS = 10V ––– VDD = 38V ––– ID = 48A ns ––– RG = 4.6Ω ––– VGS = 10V „ D Between lead, ––– 6mm (0.25in.) nH G from package ––– and center of die contact S ––– VGS = 0V ––– pF VDS = 25V ––– ƒ = 1.0MHz, See Fig. 5 ––– VGS = 0V, VDS = 1.0V, ƒ = 1.0MHz ––– VGS = 0V, VDS = 60V, ƒ = 1.0MHz ––– VGS = 0V, VDS = 0V to 60V Source-Drain Ratings and Characteristics IS ISM VSD trr Qrr ton Parameter Continuous Source Current (Body Diode) Pulsed Source Current (Body Diode)  Diode Forward Voltage Reverse Recovery Time Reverse Recovery Charge Forward Turn-On Time Min. Typ. Max. Units Conditions D MOSFET symbol ––– ––– 80† showing the A G integral reverse ––– ––– 320 S p-n junction diode. ––– ––– 1.3 V TJ = 25°C, IS = 48A, VGS = 0V „ ––– 85 130 ns TJ = 25°C, IF = 48A, VDD = 38V ––– 280 420 nC di/dt = 100A/µs „ Intrinsic turn-on time is negligible (turn-on is dominated by LS+LD) Notes: … Coss eff. is a fixed capacitance that gives the same charging time as Coss while VDS is rising from 0 to 80% VDSS . max. junction temperature. (See fig. 11). ‚ Starting TJ = 25°C, L = 0.24mH † Limited by TJmax , see Fig.12a, 12b, 15, 16 for typical repetitive RG = 25Ω, IAS = 48A, VGS=10V (See Figure 12). avalanche performance. ƒ ISD ≤ 48A, di/dt ≤ 330A/µs, VDD ≤ V(BR)DSS, ‡ This value determined from sample failure population. 100% TJ ≤ 175°C tested to this value in production. „ Pulse width ≤ 400µs; duty cycle ≤ 2%.  Repetitive rating; pulse width limited by 2 www.irf.com IRF3007S/LPbF 1000 1000 VGS 15V 10V 8.0V 7.0V 6.0V 5.5V 5.0V BOTTOM 4.5V VGS 15V 10V 8.0V 7.0V 6.0V 5.5V 5.0V BOTTOM 4.5V TOP 100 ID, Drain-to-Source Current (A) ID, Drain-to-Source Current (A) TOP 10 4.5V 20µs PULSE WIDTH Tj = 25°C 1 0.1 1 10 100 4.5V 10 20µs PULSE WIDTH Tj = 175°C 1 100 0.1 1 10 100 VDS, Drain-to-Source Voltage (V) Fig 1. Typical Output Characteristics Fig 2. Typical Output Characteristics 1000 100 100 Gfs, Forward Transconductance (S) ID, Drain-to-Source Current ( A) VDS, Drain-to-Source Voltage (V) T J = 175°C 10 T J = 25°C VDS = 25V 20µs PULSE WIDTH 1 4.0 5.0 6.0 7.0 8.0 VGS , Gate-to-Source Voltage (V) Fig 3. Typical Transfer Characteristics www.irf.com 9.0 T J = 175°C 80 60 T J = 25°C 40 20 VDS = 25V 20µs PULSE WIDTH 0 0 40 80 120 160 ID, Drain-to-Source Current (A) Fig 4. Typical Forward Transconductance Vs. Drain Current 3 IRF3007S/LPbF 6000 Crss Coss 4000 = Cgd = Cds + Cgd Ciss 3000 2000 1000 Coss Crss 0 1 16 12 8 4 0 10 0 100 10000 ID, Drain-to-Source Current (A) 1000.0 100.0 TJ = 175°C 10.0 1.0 T J = 25°C 0.1 0.2 0.4 0.6 0.8 1.0 1.2 VGS = 0V 1.4 80 120 160 Fig 6. Typical Gate Charge Vs. Gate-to-Source Voltage Fig 5. Typical Capacitance Vs. Drain-to-Source Voltage ISD, Reverse Drain Current (A) 40 Q G Total Gate Charge (nC) VDS, Drain-to-Source Voltage (V) 1.6 VSD, Source-toDrain Voltage (V) Fig 7. Typical Source-Drain Diode Forward Voltage 4 VDS= 60V VDS= 38V VDS= 15V ID= 48A VGS , Gate-to-Source Voltage (V) 5000 C, Capacitance (pF) 20 VGS = 0V, f = 1 MHZ C iss = C gs + C gd , C ds SHORTED 1000 100 100µsec 10 1 0.1 1.8 OPERATION IN THIS AREA LIMITED BY RDS(on) 1msec 10msec Tc = 25°C Tj = 175°C Single Pulse 1 10 100 1000 VDS , Drain-toSource Voltage (V) Fig 8. Maximum Safe Operating Area www.irf.com IRF3007S/LPbF 70 3.0 2.5 40 30 20 10 0 25 50 75 100 125 150 2.0 (Normalized) 50 RDS(on) , Drain-to-Source On Resistance ID, Drain Current (A) 60 I D = 80A 175 1.5 1.0 0.5 V GS = 10V 0.0 -60 -40 -20 0 20 40 60 80 100 120 140 160 180 ( °C) TJ, Junction Temperature T C , Case Temperature (°C) Fig 10. Normalized On-Resistance Vs. Temperature Fig 9. Maximum Drain Current Vs. Case Temperature Thermal Response ( Z thJC ) 10 1 D = 0.50 0.20 0.10 0.1 0.05 P DM 0.02 0.01 0.01 t1 t2 SINGLE PULSE ( THERMAL RESPONSE ) Notes: 1. Duty factor D = 2. Peak T t1/ t 2 J = P DM x Z thJC +T C 0.001 1E-006 1E-005 0.0001 0.001 0.01 0.1 1 t1 , Rectangular Pulse Duration (sec) Fig 11. Maximum Effective Transient Thermal Impedance, Junction-to-Case www.irf.com 5 IRF3007S/LPbF DRIVER L VDS D.U.T RG 20V VGS + V - DD IAS A 0.01Ω tp Fig 12a. Unclamped Inductive Test Circuit V(BR)DSS tp EAS , Single Pulse Avalanche Energy (mJ) 700 15V ID 20A 34A BOTTOM 48A TOP 600 500 400 300 200 100 0 25 50 75 100 125 150 Starting T J , Junction Temperature (°C) I AS Fig 12c. Maximum Avalanche Energy Vs. Drain Current Fig 12b. Unclamped Inductive Waveforms QG QGS QGD 4.0 VG Charge Fig 13a. Basic Gate Charge Waveform Current Regulator Same Type as D.U.T. 50KΩ 12V .2µF .3µF D.U.T. + V - DS -VGS(th) Gate threshold Voltage (V) 10 V ID = 250µA 3.0 2.0 1.0 -75 VGS -50 -25 0 25 50 75 100 125 150 175 T J , Temperature ( °C ) 3mA IG ID Current Sampling Resistors Fig 13b. Gate Charge Test Circuit 6 Fig 14. Threshold Voltage Vs. Temperature www.irf.com IRF3007S/LPbF 1000 Avalanche Current (A) Duty Cycle = Single Pulse Allowed avalanche Current vs avalanche pulsewidth, tav assuming ∆ Tj = 25°C due to avalanche losses. Note: In no case should Tj be allowed to exceed Tjmax 100 0.01 0.05 10 0.10 1 0.1 1.0E-08 1.0E-07 1.0E-06 1.0E-05 1.0E-04 1.0E-03 1.0E-02 1.0E-01 tav (sec) Fig 15. Typical Avalanche Current Vs.Pulsewidth EAR , Avalanche Energy (mJ) 300 T OP Single Pulse BOTT OM 50% Duty Cycle ID = 48A 200 100 0 25 50 75 100 125 150 Starting TJ , Junction Temperature (°C) Fig 16. Maximum Avalanche Energy Vs. Temperature www.irf.com Notes on Repetitive Avalanche Curves , Figures 15, 16: (For further info, see AN-1005 at www.irf.com) 1. Avalanche failures assumption: Purely a thermal phenomenon and failure occurs at a temperature far in excess of T jmax. This is validated for every part type. 2. Safe operation in Avalanche is allowed as long asTjmax is not exceeded. 3. Equation below based on circuit and waveforms shown in Figures 12a, 12b. 4. PD (ave) = Average power dissipation per single avalanche pulse. 5. BV = Rated breakdown voltage (1.3 factor accounts for voltage increase during avalanche). 6. Iav = Allowable avalanche current. 7. ∆T = Allowable rise in junction temperature, not to exceed Tjmax (assumed as 25°C in Figure 15, 16). tav = Average time in avalanche. 175 D = Duty cycle in avalanche = tav ·f ZthJC(D, tav ) = Transient thermal resistance, see figure 11) PD (ave) = 1/2 ( 1.3·BV·Iav) = DT/ ZthJC Iav = 2DT/ [1.3·BV·Zth] EAS (AR) = PD (ave)·tav 7 IRF3007S/LPbF D.U.T Driver Gate Drive ƒ + ‚ - „ * D.U.T. ISD Waveform Reverse Recovery Current +  RG • • • • dv/dt controlled by RG Driver same type as D.U.T. I SD controlled by Duty Factor "D" D.U.T. - Device Under Test P.W. Period VGS=10V Circuit Layout Considerations • Low Stray Inductance • Ground Plane • Low Leakage Inductance Current Transformer - D= Period P.W. + VDD + Body Diode Forward Current di/dt D.U.T. VDS Waveform Diode Recovery dv/dt Re-Applied Voltage - Body Diode VDD Forward Drop Inductor Curent Ripple ≤ 5% ISD * VGS = 5V for Logic Level Devices Fig 17. Peak Diode Recovery dv/dt Test Circuit for N-Channel HEXFET® Power MOSFETs V DS VGS RG RD D.U.T. + -VDD 10V Pulse Width ≤ 1 µs Duty Factor ≤ 0.1 % Fig 18a. Switching Time Test Circuit VDS 90% 10% VGS td(on) tr t d(off) tf Fig 18b. Switching Time Waveforms 8 www.irf.com IRF3007S/LPbF D2Pak (TO-263AB) Package Outline Dimensions are shown in millimeters (inches) D2Pak (TO-263AB) Part Marking Information T HIS IS AN IRF530S WIT H LOT CODE 8024 ASSE MB LED ON WW 02, 2000 IN THE AS SEMBLY LINE "L" INTE RNATIONAL RE CTIFIER LOGO AS SEMBLY LOT CODE PART NUMBER F 530S DATE CODE YEAR 0 = 2000 WEEK 02 LINE L OR INTE RNATIONAL RECTIF IER LOGO ASS EMBLY LOT CODE PART NUMBER F530S DATE CODE P = DES IGNAT ES LEAD - F REE PRODUCT (OPTIONAL) YEAR 0 = 2000 WEEK 02 A = ASSE MBLY SIT E CODE Notes: 1. For an Automotive Qualified version of this part please seehttp://www.irf.com/product-info/auto/ 2. For the most current drawing please refer to IR website at http://www.irf.com/package/ www.irf.com 9 IRF3007S/LPbF TO-262 Package Outline Dimensions are shown in millimeters (inches) TO-262 Part Marking Information EXAMPLE: T HIS IS AN IRL3103L LOT CODE 1789 AS S EMBLED ON WW 19, 1997 IN T HE AS S EMBLY LINE "C" Note: "P" in ass embly line pos ition indicates "Lead-F ree" INTERNATIONAL RECT IFIER LOGO AS S EMBLY LOT CODE PART NUMBER DATE CODE YEAR 7 = 1997 WEEK 19 LINE C OR INTERNATIONAL RECTIFIER LOGO AS S EMBLY LOT CODE PART NUMBER DAT E CODE P = DES IGNAT ES LEAD-FREE PRODUCT (OPT IONAL) YEAR 7 = 1997 WEEK 19 A = AS S EMBLY S ITE CODE Notes: 1. For an Automotive Qualified version of this part please seehttp://www.irf.com/product-info/auto/ 2. For the most current drawing please refer to IR website at http://www.irf.com/package/ 10 www.irf.com IRF3007S/LPbF D2Pak Tape & Reel Information Dimensions are shown in millimeters (inches) TRR 1.60 (.063) 1.50 (.059) 4.10 (.161) 3.90 (.153) FEED DIRECTION 1.85 (.073) 1.65 (.065) 1.60 (.063) 1.50 (.059) 11.60 (.457) 11.40 (.449) 0.368 (.0145) 0.342 (.0135) 15.42 (.609) 15.22 (.601) 24.30 (.957) 23.90 (.941) TRL 10.90 (.429) 10.70 (.421) 1.75 (.069) 1.25 (.049) 4.72 (.136) 4.52 (.178) 16.10 (.634) 15.90 (.626) FEED DIRECTION 13.50 (.532) 12.80 (.504) 27.40 (1.079) 23.90 (.941) 4 330.00 (14.173) MAX. 60.00 (2.362) MIN. NOTES : 1. COMFORMS TO EIA-418. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSION MEASURED @ HUB. 4. INCLUDES FLANGE DISTORTION @ OUTER EDGE. 26.40 (1.039) 24.40 (.961) 3 30.40 (1.197) MAX. 4 Data and specifications subject to change without notice. This product has been designed and qualified for the Industrial market. Qualification Standards can be found on IR’s Web site. IR WORLD HEADQUARTERS: 233 Kansas St., El Segundo, California 90245, USA Tel: (310) 252-7105 TAC Fax: (310) 252-7903 Visit us at www.irf.com for sales contact information. 07/2010 www.irf.com 11