PD- 91792A
IRL3215
HEXFET® Power MOSFET
l
l
l
l
l
l
Advanced Process Technology
Ultra Low On-Resistance
Dynamic dv/dt Rating
175°C Operating Temperature
Fast Switching
Fully Avalanche Rated
D
VDSS = 150V
RDS(on) = 0.166 Ω
G
ID = 12A
S
Description
Fifth Generation HEXFETs from International Rectifier utilize advanced
processing techniques to achieve extremely low on-resistance per silicon area.
This benefit, combined with the fast switching speed and ruggedized device
design that HEXFET Power MOSFETs are well known for, provides the
designer with an extremely efficient and reliable device for use in a wide variety
of applications.
The TO-220 package is universally preferred for all commercial-industrial
applications at power dissipation levels to approximately 50 watts. The low
thermal resistance and low package cost of the TO-220 contribute to its wide
acceptance throughout the industry.
TO-220AB
Absolute Maximum Ratings
Parameter
ID @ TC = 25°C
ID @ TC = 100°C
IDM
PD @TC = 25°C
VGS
EAS
IAR
EAR
dv/dt
TJ
TSTG
Continuous Drain Current, VGS @ 10V
Continuous Drain Current, VGS @ 10V
Pulsed Drain Current
Power Dissipation
Linear Derating Factor
Gate-to-Source Voltage
Single Pulse Avalanche Energy
Avalanche Current
Repetitive Avalanche Energy
Peak Diode Recovery dv/dt
Operating Junction and
Storage Temperature Range
Soldering Temperature, for 10 seconds
Mounting torque, 6-32 or M3 srew
Max.
Units
12
8.5
48
80
0.53
±16
130
7.2
8.0
5.0
-55 to + 175
A
W
W/°C
V
mJ
A
mJ
V/ns
°C
300 (1.6mm from case )
10 lbf•in (1.1N•m)
Thermal Resistance
Parameter
RθJC
RθCS
RθJA
www.irf.com
Junction-to-Case
Case-to-Sink, Flat, Greased Surface
Junction-to-Ambient
Typ.
Max.
Units
–––
0.50
–––
1.9
–––
62
°C/W
1
07/22/11
IRL3215
Electrical Characteristics @ TJ = 25°C (unless otherwise specified)
ΔV(BR)DSS/ΔTJ
Parameter
Drain-to-Source Breakdown Voltage
Breakdown Voltage Temp. Coefficient
RDS(on)
Static Drain-to-Source On-Resistance
VGS(th)
gfs
Gate Threshold Voltage
Forward Transconductance
IDSS
Drain-to-Source Leakage Current
V(BR)DSS
Qg
Qgs
Qgd
td(on)
tr
td(off)
tf
Gate-to-Source Forward Leakage
Gate-to-Source Reverse Leakage
Total Gate Charge
Gate-to-Source Charge
Gate-to-Drain ("Miller") Charge
Turn-On Delay Time
Rise Time
Turn-Off Delay Time
Fall Time
LD
Internal Drain Inductance
LS
Internal Source Inductance
Ciss
Coss
Crss
Input Capacitance
Output Capacitance
Reverse Transfer Capacitance
IGSS
Min. Typ. Max. Units
Conditions
150 ––– –––
V
VGS = 0V, ID = 250μA
––– 0.20 ––– V/°C Reference to 25°C, ID = 1mA
––– ––– 0.166
VGS = 10V, ID = 7.2A
––– ––– 0.184
Ω
VGS = 5.0V, ID = 7.2A
––– ––– 0.208
VGS = 4.0V, ID = 6A
1.0
––– 2.0
V
VDS = VGS, ID = 250μA
8.3
––– –––
S
VDS = 25V, ID = 7.2A
––– –––
25
VDS = 150V, VGS = 0V
μA
––– ––– 250
VDS = 120V, VGS = 0V, TJ = 150°C
––– ––– 100
VGS = 16V
nA
––– ––– -100
VGS = -16V
––– –––
35
ID = 7.2A
––– ––– 4.1
nC
VDS = 120V
––– –––
21
VGS = 5.0V, See Fig. 6 and 13
–––
7.4 –––
VDD = 75V
–––
45
–––
ID = 7.2A
ns
–––
38
–––
RG = 12Ω, VGS = 5.0V
–––
36
–––
RD = 10.2Ω, See Fig. 10
Between lead,
4.5
nH
6mm (0.25in.)
G
from package
––– 7.5 –––
and center of die contact
––– 775 –––
VGS = 0V
––– 140 –––
pF
VDS = 25V
–––
70
–––
ƒ = 1.0MHz, See Fig. 5
D
S
Source-Drain Ratings and Characteristics
IS
ISM
VSD
trr
Qrr
ton
Parameter
Continuous Source Current
(Body Diode)
Pulsed Source Current
(Body Diode)
Diode Forward Voltage
Reverse Recovery Time
Reverse RecoveryCharge
Forward Turn-On Time
Min. Typ. Max. Units
Conditions
D
MOSFET symbol
––– ––– 12
showing the
A
G
integral reverse
––– –––
48
S
p-n junction diode.
––– ––– 1.3
V
TJ = 25°C, IS = 7.2A, VGS = 0V
––– 160 240
ns
TJ = 25°C, IF = 7.2A
––– 810 1210 nC
di/dt = 100A/μs
Intrinsic turn-on time is negligible (turn-on is dominated by LS+LD)
Notes:
Repetitive rating; pulse width limited by
Pulse width ≤ 300μs; duty cycle ≤ 2%.
Starting TJ = 25°C, L = 4.9mH
Caculated continuous current based on maximum allowable
max. junction temperature. ( See fig. 11 )
RG = 25Ω, IAS = 7.2A. (See Figure 12)
ISD ≤ 7.2A, di/dt ≤ 100A/μs, VDD ≤ V(BR)DSS,
junction temperature;for recommended current-handling of the
package refer to Design Tip # 93-4
TJ ≤ 175°C
2
www.irf.com
IRL3215
100
100
VGS
15V
10V
5.0V
4.5V
3.5V
3.0V
2.75V
BOTTOM 2.5V
VGS
15V
10V
5.0V
4.5V
3.5V
3.0V
2.75V
BOTTOM 2.5V
10
TOP
ID, Drain-to-Source Current (A)
ID, Drain-to-Source Current (A)
TOP
2.5V
1
10
2.5V
1
20μs PULSE WIDTH
Tj = 175°C
20μs PULSE WIDTH
Tj = 25°C
0.1
0.1
0.1
1
10
0.1
100
3.0
RDS(on) , Drain-to-Source On Resistance
(Normalized)
ID, Drain-to-Source Current (Α)
100.00
T J = 175°C
10.00
VDS = 15V
20μs PULSE WIDTH
1.00
1.0
3.0
5.0
7.0
9.0
11.0
13.0
VGS, Gate-to-Source Voltage (V)
Fig 3. Typical Transfer Characteristics
www.irf.com
10
100
Fig 2. Typical Output Characteristics
Fig 1. Typical Output Characteristics
T J = 25°C
1
VDS, Drain-to-Source Voltage (V)
VDS, Drain-to-Source Voltage (V)
15.0
ID = 12A
2.5
2.0
1.5
1.0
0.5
0.0
-60 -40 -20 0
VGS = 10V
20 40 60 80 100 120 140 160 180
TJ , Junction Temperature ( °C)
Fig 4. Normalized On-Resistance
Vs. Temperature
3
IRL3215
VGS = 0V,
f = 1MHz
Ciss = Cgs + Cgd , Cds SHORTED
Crss = Cgd
Coss = Cds + Cgd
C, Capacitance (pF)
2000
Ciss
1500
Coss
1000
Crss
500
0
1
10
15
VGS , Gate-to-Source Voltage (V)
2500
VDS = 120V
VDS = 75V
VDS = 30V
10
5
0
100
ID = 7.2 A
FOR TEST CIRCUIT
SEE FIGURE 13
0
20
30
40
50
Fig 6. Typical Gate Charge Vs.
Gate-to-Source Voltage
Fig 5. Typical Capacitance Vs.
Drain-to-Source Voltage
100
1000
ID, Drain-to-Source Current (A)
ISD , Reverse Drain Current (A)
10
QG , Total Gate Charge (nC)
VDS , Drain-to-Source Voltage (V)
OPERATION IN THIS AREA
LIMITED BY R DS(on)
100
10
TJ = 175 ° C
1
TJ = 25 ° C
0.1
0.2
V GS = 0 V
0.4
0.6
0.8
1.0
VSD ,Source-to-Drain Voltage (V)
Fig 7. Typical Source-Drain Diode
Forward Voltage
4
1.2
10
100μsec
1msec
1
10msec
Tc = 25°C
Tj = 175°C
Single Pulse
0.1
1
10
100
1000
VDS, Drain-to-Source Voltage (V)
Fig 8. Maximum Safe Operating Area
www.irf.com
IRL3215
12
RD
V DS
ID , Drain Current (A)
VGS
D.U.T.
9
RG
6
Pulse Width ≤ 1 µs
Duty Factor ≤ 0.1 %
+
-VDD
10V
Fig 10a. Switching Time Test Circuit
3
VDS
90%
0
25
50
75
100
125
150
175
TC , Case Temperature ( °C)
Fig 9. Maximum Drain Current Vs.
Case Temperature
10%
VGS
td(on)
tr
t d(off)
tf
Fig 10b. Switching Time Waveforms
Thermal Response (Z thJC )
10
1 D = 0.50
0.20
0.10
PDM
0.05
0.1
0.02
0.01
SINGLE PULSE
(THERMAL RESPONSE)
t1
t2
Notes:
1. Duty factor D = t 1 / t 2
2. Peak T J = P DM x Z thJC + TC
0.01
0.00001
0.0001
0.001
0.01
0.1
1
t1 , Rectangular Pulse Duration (sec)
Fig 11. Maximum Effective Transient Thermal Impedance, Junction-to-Case
www.irf.com
5
15V
L
VDS
D.U.T
RG
IAS
20V
DRIVER
+
V
- DD
0.01Ω
tp
Fig 12a. Unclamped Inductive Test Circuit
A
EAS , Single Pulse Avalanche Energy (mJ)
IRL3215
300
TOP
250
BOTTOM
ID
2.9A
5.1A
7.2A
200
150
100
50
0
25
50
75
100
125
150
175
Starting TJ , Junction Temperature ( °C)
V(BR)DSS
tp
Fig 12c. Maximum Avalanche Energy
Vs. Drain Current
I AS
Current Regulator
Same Type as D.U.T.
Fig 12b. Unclamped Inductive Waveforms
50KΩ
QG
10 V
QGS
.3μF
D.U.T.
QGD
+
V
- DS
VGS
VG
3mA
Charge
Fig 13a. Basic Gate Charge Waveform
6
12V
.2μF
IG
ID
Current Sampling Resistors
Fig 13b. Gate Charge Test Circuit
www.irf.com
IRL3215
Peak Diode Recovery dv/dt Test Circuit
+
D.U.T
Circuit Layout Considerations
• Low Stray Inductance
• Ground Plane
• Low Leakage Inductance
Current Transformer
+
-
-
+
RG
•
•
•
•
Driver Gate Drive
P.W.
+
dv/dt controlled by RG
Driver same type as D.U.T.
ISD controlled by Duty Factor "D"
D.U.T. - Device Under Test
Period
D=
-
VDD
P.W.
Period
VGS=10V
*
D.U.T. ISD Waveform
Reverse
Recovery
Current
Body Diode Forward
Current
di/dt
D.U.T. VDS Waveform
Diode Recovery
dv/dt
Re-Applied
Voltage
Body Diode
VDD
Forward Drop
Inductor Curent
Ripple ≤ 5%
ISD
* VGS = 5V for Logic Level Devices
Fig 14. For N-Channel HEXFETS
www.irf.com
7
IRL3215
TO-220AB Package Outline
Dimensions are shown in millimeters (inches)
2.87 (.113)
2.62 (.103)
10.54 (.415)
10.29 (.405)
3.78 (.149)
3.54 (.139)
-A-
-B4.69 (.185)
4.20 (.165)
1.32 (.052)
1.22 (.048)
6.47 (.255)
6.10 (.240)
4
15.24 (.600)
14.84 (.584)
LEAD ASSIGNMENTS
1 - GATE
2 - DRAIN
3 - SOURCE
4 - DRAIN
1.15 (.045)
MIN
1
2
3
14.09 (.555)
13.47 (.530)
4.06 (.160)
3.55 (.140)
3X
3X
1.40 (.055)
1.15 (.045)
0.93 (.037)
0.69 (.027)
0.36 (.014)
3X
M
B A M
0.55 (.022)
0.46 (.018)
2.92 (.115)
2.64 (.104)
2.54 (.100)
2X
NOTES:
1 DIMENSIONING & TOLERANCING PER ANSI Y14.5M, 1982.
2 CONTROLLING DIMENSION : INCH
3 OUTLINE CONFORMS TO JEDEC OUTLINE TO-220AB.
4 HEATSINK & LEAD MEASUREMENTS DO NOT INCLUDE BURRS.
Part Marking Information
EXAMPLE : THIS IS AN IRF1010
WITH ASSEMBLY
LOT CODE 9B1M
A
INTERNATIONAL
RECTIFIER
LOGO
ASSEMBLY
LOT CODE
PART NUMBER
IRF1010
9246
9B 1M
DATE CODE
(YYWW)
YY = YEAR
WW = WEEK
Note: For the most current drawing please refer to IR website at http://www.irf.com/package/
Data and specifications subject to change without notice.
This product has been designed and qualified for the TBD market.
Qualification Standards can be found on IR’s Web site.
IR WORLD HEADQUARTERS: 101 N. Sepulveda Blvd., El Segundo, California 90245, USA Tel: (310) 252-7105
TAC Fax: (310) 252-7903
Visit us at www.irf.com for sales contact information. 07/11
8
www.irf.com
