IRL530NSTRRPBF

PD- 95593 IRL530NSPbF IRL530NLPbF • Lead-Free www.irf.com 1 07/21/04 IRL530NS/LPbF 2 www.irf.com IRL530NS/LPbF www.irf.com 3 IRL530NS/LPbF 4 www.irf.com IRL530NS/LPbF www.irf.com 5 IRL530NS/LPbF 6 www.irf.com IRL530NS/LPbF Peak Diode Recovery dv/dt Test Circuit Circuit Layout Considerations • Low Stray Inductance • Ground Plane • Low Leakage Inductance Current Transformer + + - - + • dv/dt controlled by RG • ISD controlled by Duty Factor "D" • D.U.T. - Device Under Test + - * Reverse Polarity for P-Channel ** Use P-Channel Driver for P-Channel Measurements Driver Gate Drive P.W. D= Period P.W. Period VGS=10V D.U.T. ISD Waveform Reverse Recovery Current Body Diode Forward Current di/dt D.U.T. VDS Waveform Diode Recovery dv/dt Re-Applied Voltage Body Diode VDD Forward Drop Inductor Curent Ripple ≤ 5% ISD *** VGS = 5.0V for Logic Level and 3V Drive Devices Fig 14 For N Channel HEXFETS www.irf.com 7 IRL530NS/LPbF D2Pak Package Outline Dimensions are shown in millimeters (inches) D2Pak Part Marking Information T H IS IS AN IR F 530S WIT H L OT CODE 8024 AS S E MB L E D ON WW 02, 2000 IN T H E AS S E MB L Y L INE "L " INT E RNAT IONAL RE CT IF IE R L OGO Note: "P" in as s embly line pos ition indicates "L ead-F ree" PART NUMB E R F 530S AS S E MB L Y L OT CODE DAT E CODE YE AR 0 = 2000 WE E K 02 L INE L OR INT E R NAT IONAL R E CT IF IE R L OGO AS S E MB LY L OT CODE 8 PAR T NU MB E R F 530S DAT E CODE P = DE S IGNAT E S L E AD-F R E E PR ODU CT (OPT IONAL ) YE AR 0 = 2000 WE E K 02 A = AS S EMB L Y S IT E CODE www.irf.com IRL530NS/LPbF TO-262 Package Outline Dimensions are shown in millimeters (inches) TO-262 Part Marking Information E XAMPL E : T H IS IS AN IR L 3103L L OT CODE 1789 AS S E MB L E D ON WW 19, 1997 IN T H E AS S E MB L Y L INE "C" Note: "P" in as s embly line pos ition indicates "L ead-F ree" INT E RNAT IONAL RE CT IF IE R L OGO AS S E MB L Y L OT CODE PART NUMB E R DAT E CODE YE AR 7 = 1997 WE E K 19 L INE C OR INT E R NAT IONAL R E CT IF IE R L OGO AS S E MB L Y L OT CODE www.irf.com PAR T NU MB E R DAT E CODE P = DE S IGNAT E S L E AD-F RE E PR ODU CT (OP T IONAL ) YE AR 7 = 1997 WE E K 19 A = AS S E MB L Y S IT E CODE 9 IRL530NS/LPbF D2Pak Tape & Reel Information Dimensions are shown in millimeters (inches) TRR 1.60 (.063) 1.50 (.059) 4.10 (.161) 3.90 (.153) FEED DIRECTION 1.85 (.073) 1.60 (.063) 1.50 (.059) 11.60 (.457) 11.40 (.449) 1.65 (.065) 0.368 (.0145) 0.342 (.0135) 15.42 (.609) 15.22 (.601) 24.30 (.957) 23.90 (.941) TRL 1.75 (.069) 1.25 (.049) 10.90 (.429) 10.70 (.421) 4.72 (.136) 4.52 (.178) 16.10 (.634) 15.90 (.626) FEED DIRECTION 13.50 (.532) 12.80 (.504) 27.40 (1.079) 23.90 (.941) 4 330.00 (14.173) MAX. 60.00 (2.362) MIN. NOTES : 1. COMFORMS TO EIA-418. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSION MEASURED @ HUB. 4. INCLUDES FLANGE DISTORTION @ OUTER EDGE. 30.40 (1.197) MAX. 26.40 (1.039) 24.40 (.961) 3 4 Data and specifications subject to change without notice. IR WORLD HEADQUARTERS: 233 Kansas St., El Segundo, California 90245, USA Tel: (310) 252-7105 TAC Fax: (310) 252-7903 Visit us at www.irf.com for sales contact information. 07/04 10 www.irf.com Note: For the most current drawings please refer to the IR website at: http://www.irf.com/package/ IMPORTANT NOTICE The information given in this document shall in no event be regarded as a guarantee of conditions or characteristics (“Beschaffenheitsgarantie”) . With respect to any examples, hints or any typical values stated herein and/or any information regarding the application of the product, Infineon Technologies hereby disclaims any and all warranties and liabilities of any kind, including without limitation warranties of non-infringement of intellectual property rights of any third party. In addition, any information given in this document is subject to customer’s compliance with its obligations stated in this document and any applicable legal requirements, norms and standards concerning customer’s products and any use of the product of Infineon Technologies in customer’s applications. The data contained in this document is exclusively intended for technically trained staff. It is the responsibility of customer’s technical departments to evaluate the suitability of the product for the intended application and the completeness of the product information given in this document with respect to such application. For further information on the product, technology, delivery terms and conditions and prices please contact your nearest Infineon Technologies office (www.infineon.com). WARNINGS Due to technical requirements products may contain dangerous substances. For information on the types in question please contact your nearest Infineon Technologies office. Except as otherwise explicitly approved by Infineon Technologies in a written document signed by authorized representatives of Infineon Technologies, Infineon Technologies’ products may not be used in any applications where a failure of the product or any consequences of the use thereof can reasonably be expected to result in personal injury.