PVI1050NPBF

PVI1050NPbF PVI1050NS/TPbF PVI5050NPbF PVI5050NSPbF Photovoltaic Isolator Single and Dual Channel 5-10 Volt Output General Description The PVI Series Photovoltaic Isolator generates an electrically isolated DC voltage upon receipt of a DC input signal. It is capable of directly driving gates of power MOSFETs or IGBTs. It utilizes a monolithic integrated circuit photovoltaic generator of novel construction as its output. The output is controlled by radiation from a GaAlAs light emitting diode (LED), which is optically isolated from the photovoltaic generator. Features      Isolated Voltage Source Monolithic Construction Up to 5A Output Single or Dual Output Solid-State Reliability The PVI Series is ideally suited for applications requiring high-current and/or high-voltage switching with optical isolation between the low-level driving circuitry and high-energy or high-voltage load circuits. It can be used for directly driving gates of power MOSFETs. The dual-channel device allows its outputs to drive independent discrete power MOSFETs, or be connected in parallel or in series to provide higher current drive for power MOSFETs or higher voltage drive for IGBTs. The PVI Series Photovoltaic isolators employ fast turn-off circuitry. These PVI Series Photovoltaic Isolators are packaged in 8-pin, molded DIP packages and available with either thru-hole or surface-mount (“gull-wing”) leads, in plastic shipping tubes. Applications  Load Distribution  Industrial Controls  Current-to-Voltage Conversion  Custom Solid-State Relay Part Identification PVI1050NPbF PVI5050NPbF thru-hole thru-hole PVI1050NSPbF Surface-mount (gull-wing) Surface-mount (gull-wing) PVI5050NSPbF PVI1050NS-TPbF 1 Surface-mount, tape and reel 2017-12-05 PVI1050NPbF/PVI1050NS/TPbF PVI5050NPbF/PVI5050NSPbF Electrical Specifications (-40°C TA  +85°C unless otherwise specified) INPUT CHARACTERISTICS Limits Units 2.0 to 50 mA (DC) Maximum Forward Voltage Drop @ 10mA, 25°C (see figure 5) 1.4 V (DC) Maximum Reverse Voltage 6.0 V (DC) Maximum Reverse Current @ -6.0V (DC), 25°C 100 A (DC) Maximum Pulsed Input Current @ 25°C (see figure 6) 1.0 A (peak) Limits Units 8.0 per channel V(DC) 10 A (DC) Input Current Range (see figure 4) OUTPUT CHARACTERISTICS Maximum Forward Voltage @ 10µA Maximum Reverse Current @ -10VDC Limits PVI5050N COUPLED CHARACTERISTICS Minimum Open Circuit Voltage @ ILED = 10mA, 25°C, RL = >10M (see figures 1 to 2) 5.0 Minimum Short Circuit Current @ ILED = 10mA, 25°C (see figures 1 to 2) 5.0 Maximum Capacitance (Input/Output) 1.0 Limits PVI1050N 5.0/channel 10 series 5.0/channel 10 series Units V(DC) A (DC) 2.0 pF Maximum Ton Time @ ILED=10mA, CLOAD=10pF (See Figure7) RL > 20M 300 µS RL=10M 160 µS RL=4.7M 90 µS 220 µS Maximum Toff Time @ ILED=10mA, CLOAD=10pF (See Figure7) GENERAL CHARACTERISTICS Minimum Dielectric Strength, Input-Output Limits PVI5050N Limits PVI1050N Units 4000 2500 VRMS Minimum Dielectric Strength, Output-to-Output 1200 VDC Minimum Insulation Resistance, Input-to-Output, @TA=+25°C, 50%RH, 100VDC Maximum Pin Soldering Temperature (10 seconds maximum) 1012  Ambient Temperature Range: +260 Operating -40 to 85 Storage -40 to 125 °C Infineon Technology does not recommend the use of this product in aerospace, avionics, military or life support applications. Users of this Infineon Technology product in such applications assume all risks of such use and indemnify Infineon Technology against all damages resulting from such use. 2 2017-12-05 PVI1050NPbF/PVI1050NS/TPbF PVI5050NPbF/PVI5050NSPbF Figure 1. Typical Output Characteristics 3 Figure 2. Typical Variation of Output Figure 3. Input Current Derating Figure 4. Input Characteristics Figure 5. Input Pulse Capability Figure 6. Typical Response Time 2017-12-05 PVI1050NPbF/PVI1050NS/TPbF PVI5050NPbF/PVI5050NSPbF Wiring Diagram Application Note: The outputs of the PVI1050N (pins 5-6 and 7-8) may be placed in series connection to produce a 10-volt output with a 5µA minimum short circuit current. Alternatively, the two ouptut of the PVI1050 may be connected in parallel to produce a 5.0-volt ouput with a 10µA minimum short circuit current. The two outputs of the PVI1050N may be applied separately with a maximum 1200VDC between the outputs. Input-tooutput isolation to either output is 2500V (RMS). 4 2017-12-05 PVI1050NPbF/PVI1050NS/TPbF PVI5050NPbF/PVI5050NSPbF Case Outlines 5 2017-12-05 PVI1050NPbF/PVI1050NS/TPbF PVI5050NPbF/PVI5050NSPbF Case Outlines 6 2017-12-05 PVI1050NPbF/PVI1050NS/TPbF PVI5050NPbF/PVI5050NSPbF Qualifiction Information Industrial (per JEDEC JESD47F† guidelines) Qualification Level Moisture Sensitivity Level PVI1050NPbF PVI5050NPbF PVI1050NSPbF PVI5050NSPbF PVI1050NS-TPbF N/A MSL4 (per JEDEC J-STD-020E & JEDEC J-STD-033C) † RoHS Compliant Yes † Applicable version of JEDEC standard at the time of product release. 7 2017-12-05 PVI1050NPbF/PVI1050NS/TPbF PVI5050NPbF/PVI5050NSPbF Trademarks of Infineon Technologies AG µHVIC™, µIPM™, µPFC™, AU-ConvertIR™, AURIX™, C166™, CanPAK™, CIPOS™, CIPURSE™, CoolDP™, CoolGaN™, COOLiR™, CoolMOS™, CoolSET™, CoolSiC™, DAVE™, DI-POL™, DirectFET™, DrBlade™, EasyPIM™, EconoBRIDGE™, EconoDUAL™, EconoPACK™, EconoPIM™, EiceDRIVER™, eupec™, FCOS™, GaNpowIR™, HEXFET™, HITFET™, HybridPACK™, iMOTION™, IRAM™, ISOFACE™, IsoPACK™, LEDrivIR™, LITIX™, MIPAQ™, ModSTACK™, my-d™, NovalithIC™, OPTIGA™, OptiMOS™, ORIGA™, PowIRaudio™, PowIRStage™, PrimePACK™, PrimeSTACK™, PROFET™, PRO-SIL™, RASIC™, REAL3™, SmartLEWIS™, SOLID FLASH™, SPOC™, StrongIRFET™, SupIRBuck™, TEMPFET™, TRENCHSTOP™, TriCore™, UHVIC™, XHP™, XMC™ Trademarks updated November 2015 Other Trademarks All referenced product or service names and trademarks are the property of their respective owners. Edition 2016-04-19 Published by Infineon Technologies AG 81726 Munich, Germany © 2016 Infineon Technologies AG. All Rights Reserved. Do you have a question about this document? Email: erratum@infineon.com Document reference ifx1 IMPORTANT NOTICE The information given in this document shall in no event be regarded as a guarantee of conditions or characteristics (“Beschaffenheitsgarantie”) . With respect to any examples, hints or any typical values stated herein and/or any information regarding the application of the product, Infineon Technologies hereby disclaims any and all warranties and liabilities of any kind, including without limitation warranties of non-infringement of intellectual property rights of any third party. In addition, any information given in this document is subject to customer’s compliance with its obligations stated in this document and any applicable legal requirements, norms and standards concerning customer’s products and any use of the product of Infineon Technologies in customer’s applications. The data contained in this document is exclusively intended for technically trained staff. It is the responsibility of customer’s technical departments to evaluate the suitability of the product for the intended application and the completeness of the product information given in this document with respect to such application. 8 For further information on the product, technology, delivery terms and conditions and prices please contact your nearest Infineon Technologies office (www.infineon.com). Please note that this product is not qualified according to the AEC Q100 or AEC Q101 documents of the Automotive Electronics Council. WARNINGS Due to technical requirements products may contain dangerous substances. For information on the types in question please contact your nearest Infineon Technologies office. Except as otherwise explicitly approved by Infineon Technologies in a written document signed by authorized representatives of Infineon Technologies, Infineon Technologies’ products may not be used in any applications where a failure of the product or any consequences of the use thereof can reasonably be expected to result in personal injury. 2017-12-05