PVI5013RS

Series PVI5013RPbF Photovoltaic Isolator Solid-State Opto-Isolated MOSFET Gate Driver Dual-Channel, 5V, 1.0mA General Description The PVI5013R Photovoltaic Isolator is a dual-channel, opto-isolated driver capable of directly driving gates of power MOSFETs or IGBTs. It utilizes a monolithic integrated circuit photovoltaic generator of novel construction as its output. The output is controlled by radiation from a GaAlAs light emitting diode (LED) which is optically isolated from the photovoltaic generator. The PVI5013R is ideally suited for applications requiring high-current and/or high voltage switching with optical isolation between the low-level driving circuitry and high-energy or high- voltage load circuits. It can be used for directly driving gates of power MOSFETs. The dual- channel configuration allows its outputs to drive independent discrete power MOSFETs, or be connected in parallel or in series to provide higher-current drive for power MOSFETs or higher-voltage drive for IGBTs. PVI5013R employs a fast turn-off circuitry. PVI5013R Photovoltaic Isolators are packaged in an 8-pin, molded DIP package with either thru-hole or surface-mount (gull-wing) terminals. It is available in standard plastic shipping tubes or on tape-and-reel. Please refer to Part Identification information opposite. Applications § Telecommunications § Load Distribution § Industrial Controls § Instrumentation and Measurement 1 www.irf.com © 2015 International Rectifier Features § § § § § § Monolithic construction 3,750 VRMS I/O Isolation 1,200 VDC output-to-output isolation Dual-Channel application flexibility Solid-State reliability UL recognized and BABT Certified Part Identification PVI5013RPbF PVI5013RSPbF PVI5013RS-TPbF Submit Datasheet Feedback thru-hole surface-mount surface-mount, Tape and Reel April 24, 2015 Series PVI5013RPbF Electrical Specifications (-40°C ≤ TA ≤ +85°C unless otherwise specified) INPUT CHARACTERISTICS Limits Units Minimum Input Current (see figure 1) Input Current Range (see figure 1) Maximum Continuous Input Current @ TA=+25°C LED Forward Voltage Drop @ 5mA, TA=+25°C (see figure 3) Maximum Reverse Voltage Maximum Reverse Current @ -6VDC, TA=+25°C 5.0 3.0 to 25 40 1.4 6.0 10 mA mA mA V V µA OUTPUT CHARACTERISTICS Limits Units 8.0 10 VDC µA DC Limits Units 3 V 8 V 1.0 V 1.0 µA 5 0.25 100 3300 ms ms Ω Ω Limits Units 3750 1200 VRMS VDC 1012 Ω 5.0 +260 -40 to +85 -40 to +125 pF °C °C °C Minimum Forward Voltage Maximum Reverse Current COUPLED CHARACTERISTICS Minimum Output Voltage @ ILED = 5mA, R L = 10MΩ @ TA=0°C to +70°C (see figures 1 and 2) Maximum Output Voltage @ ILED = 5mA, R L = 10MΩ @ TA=0°C to +70°C (see figures 1 and 2) Maximum Voltage Differential Between Outputs @ ILED = 5mA, RL = 10MΩ Typical Output Short-Circuit Current @ ILED = 5mA, @ TA=+25°C (see figures 1 and 2) Maximum Turn-On Time @ ILED = 5mA, CLOAD = 200pF (see figure 4) Max. Turn-Off Time @ ILED = 5mA, CLOAD = 200pF (see figure 4) Off-State Clamping Resistance: minimum maximum GENERAL CHARACTERISTICS Minimum Dielectric Strength, Input-Output Minimum Dielectric Strength, Output-to-Output Minimum Insulation Resistance, Input-to-Output @TA=+25°C, 50%RH, 100VDC Maximum Capacitance, Input-Output Maximum Pin Soldering Temperature (10 seconds maximum) Ambient Temperature Range: Operating Storage Connection Diagram International Rectifier does not recommend the use of this product in aerospace, avionics, military or life support applications. Users of this International Rectifier product in such applications assume all risks of such use and indemnify International Rectifier against all damages resulting from such use. 2 www.irf.com © 2015 International Rectifier Submit Datasheet Feedback 1 8 (+) 2 7 (-) 3 6 (+) 4 5 (-) April 24, 2015 Series PVI5013RPbF 18 Open Circuit Voltage 16 RL=10MΩ 7 14 6 12 5 10 4 8 3 6 2 4 Short Circuit Current 2 1 ILED=5mA 1.1 0 5 10 15 20 25 30 35 0 -20 20 40 80 60 100 Ambient Temperature (deg. C) Figure 2. Typical Variation of Output Response Time (microseconds) Max. device and -40 deg. C TYPICAL limit limit Min. device and +85 deg. C 4 0.7 5000 16 8 Output Voltage 0.8 0.5 -40 40 CAUTION: provide current limiting so that 25 mA maximum steadystate control current rating is not exceeded 12 0.9 Short-Circuit Current Input Current (mA) Figure 1. Typical Output Characteristics 20 1.0 0.6 0 0 Input Current (mA) Output Voltage (VDC) 8 1.2 Normalized Output 20 9 Output Short-Circuit Current (uA) 10 ILED=5mA Ton 1000 500 100 Toff 0 0 0.5 1.0 1.5 2.0 LED Forward Voltage Drop (Volts DC Figure 3. Input Characteristics (Current Controlled) 3 www.irf.com © 2015 International Rectifier 50 100 200 300 400 500 Load Capacitance (pF) Figure 4. Typical Response Time Submit Datasheet Feedback April 24, 2015 Series PVI5013RPbF Note: For the most current drawing please refer to IR website at: http://www.irf.com/package/ 4 www.irf.com © 2015 International Rectifier Submit Datasheet Feedback April 24, 2015 Series PVI5013RPbF † Qualification information Indusrial Qualification level (per JEDE C JE S D47I Moisture Sensitivity Level †† guidelines) PVI5013RPbF N/A PVI5013RSPbF MSL4 PVI5013RS-TPbF (per JE DEC J-S T D-020E & JE DE C J-S TD-033C RoHS compliant †† ) Yes † Qualification standards can be found at International Rectifier’s web site http://www.irf.com/product-info/reliability †† Applicable version of JEDEC standard at the time of product release. Revision History Date 4/24/2015 Comment • Added Qualification Information table on page 5. • Updated data sheet based on corporate template. IR WORLD HEADQUARTERS: 101 N. Sepulveda Blvd., El Segundo, California 90245, USA To contact International Rectifier, please visit http://www.irf.com/whoto-call/ 5 www.irf.com © 2015 International Rectifier Submit Datasheet Feedback April 24, 2015