PVI5033RS

Series PVI5033RPbF Photovoltaic Isolator Solid-State Opto-Isolated MOSFET Gate Driver Dual-Channel, 5V, 5mA General Description The PVI5033R Photovoltaic Isolator is a dualchannel, opto-isolated driver capable of directly driving gates of power MOSFETs or IGBTs. It utilizes a monolithic integrated circuit photovoltaic generator of novel construction as its output. The output is controlled by radiation from a GaAlAs light emitting diode (LED) which is optically isolated from the photovoltaic generator. Features § § § § § § Monolithic construction 3,750 VRMS I/O isolation 1,200 VDC output-to-output isolation Dual-Channel application flexibility Solid-State Reliability UL Recognized and BABT Certified The PVI5033R is ideally suited for applications requiring high-current and/or high voltage switching with optical isolation between the low-level driving circuitry and high-energy or high- voltage load circuits. It can be used for directly driving gates of power MOSFETs. The dual- channel configuration allows its outputs to drive independent discrete power MOSFETs, or be connected in parallel or in series to provide higher-current drive for power MOSFETs or higher-voltage drive for IGBTs. PVI5033R employs a fast turn-off circuitry. PVI5033R Photovoltaic Isolators are packaged in an 8-pin, molded DIP package with either thru-hole or “gull-wing” terminals. It is available in standard plastic shipping tubes or on tape-and-reel. Refer to Part Identification information. Applications § ÿ ÿ Telecommunications § ÿ ÿ Load Distribution § ÿ ÿ Industrial Controls § ÿ ÿ Instrumentation and Measurement § ÿ ÿ Electronic Ballast 1 www.irf.com © 2015 International Rectifier Part Identification PVI5033RPbF PVI5033RSPbF PVI5033RS-TPbF Submit Datasheet Feedback thru-hole SMT SMT, Tape and Reel April 24, 2015 Series PVI5033RPbF Electrical Specifications (-40°C ≤ TA ≤ +85°C unless otherwise specified) INPUT CHARACTERISTICS Min. Input Current (See Fig.1) Input Current Range (See Fig. 1) Max. Continuous Input Current @ TA=+25°C LED Forward Voltage Drop @ 5mA, TA=+25°C (See Fig. 3) Max. Reverse Voltage Max. Reverse Current @ -6VDC , TA=+25°C Limits 5.0 3.0 to 25 40 1.4 6.0 10 Units OUTPUT CHARACTERISTICS Limits Units 8.0 10 V DC µADC Limits Units 5 V 10 V 1.0 V 1.65 µA 5 µA 2.5 .5 350 1500 ms ms Ω Ω Limits Units 3750 1200 1012 VRMS VDC Ω 5.0 +260 -40 to +85 -40 to +125 pF °C °C °C Min. Forward Voltage Max. Reverse Current COUPLED CHARACTERISTICS Min. Output Voltage @ ILED = 10mA, RL = 10MΩ @ TA=0°C to +70°C (See Fig. 1 & 2) Max. Output Voltage @ ILED = 10mA, RL = 10MΩ @ TA=0°C to +70°C (See Fig. 1 & 2) Max. Voltage Differential Between Outputs @ ILED = 5mA, RL = 10MΩ Min. Output Short-Circuit Current @ ILED = 5mA, @ TA=+25°C (See Fig. 1 & 2) Typical Output Short-Circuit Current @ ILED = 10mA, @ TA=+25°C (See Fig. 1 & 2) Max. Turn-On Time @ ILED = 5mA, CLOAD = 200pF (See Fig. 4) Max. Turn-Off Time @ ILED = 5mA, CLOAD = 200pF (See Fig. 4) Off-State Clamping Resistance: minimum maximum GENERAL CHARACTERISTICS Min. Dielectric Strength, Input-Output Min. Dielectric Strength, Output-to-Output Min. Insulation Resistance, Input-to-Output @TA=+25°C, 50%RH, 100VDC Max. Capacitance, Input-Output Max. Pin Soldering Temperature (10 seconds max.) Ambient Temperature Range: Operating Storage Connection Diagram International Rectifier does not recommend the use of this product in aerospace, avionics, military or life support applications. Users of this International Rectifier product in such applications assume all risks of such use and indemnify International Rectifier against all damages resulting from such use. 2 www.irf.com © 2015 International Rectifier mA mA mA V V µA 1 8 (+) 2 7 (-) 3 6 (+) 4 5 (-) Submit Datasheet Feedback April 24, 2015 Series PVI5033RPbF 8 24 7 21 RL=10MW 6 18 5 15 4 12 3 9 2 6 Short Circuit Current 1 3 1.2 0 5 10 15 20 25 30 35 1.1 Output Voltage 1.0 0.9 0.8 0.7 Short-Circuit Current 0.6 0.5 0 0 ILED=5mA 1.3 p 27 Normalized Output Output Voltage (V DC ) 9 1.4 30 Open Circuit Voltage Output Short-Circuit Current (μA) 10 40 -40 Figure 1. Typical Output Characteristics Response Time ( μs) g. C limit TYPICAL Max. devic e and -40 de limit 5 deg. C ce and +8 Min. devi Input Current (mA) 0 0.5 85 100 1.0 Ton 4000 3000 2000 1000 1.5 2.0 LED Forward Voltage Drop (Volts DC) Figure 3. Input Characteristics (Current Controlled) 3 5000 0 0 60 ILED=5mA 6000 4 40 7000 16 8 25 Figure 2. Typical Variation of Output CAUTION: provide current limiting so that 25 mA maximum steadystate control current rating is not exceeded 12 0 Ambient Temperature (deg. C) Input Current (mA) 20 -20 www.irf.com © 2015 International Rectifier Toff 0 200 400 600 800 1000 Load Capacitance (pF) Figure 4. Typical Response Time Submit Datasheet Feedback April 24, 2015 Series PVI5033RPbF Note: For the most current drawing please refer to IR website at: http://www.irf.com/package/ 4 www.irf.com © 2015 International Rectifier Submit Datasheet Feedback April 24, 2015 Series PVI5033RPbF † Qualification information Indusrial Qualification level (per JEDE C JES D47I Moisture Sensitivity Level †† guidelines) PVI5033RPbF N/A PVI5033RSPbF MSL4 PVI5033RS-TPbF (per JE DEC J-S T D-020E & JE DE C J-S TD-033C RoHS compliant †† ) Yes † Qualification standards can be found at International Rectifier’s web site http://www.irf.com/product-info/reliability †† Applicable version of JEDEC standard at the time of product release. Revision History Date 4/24/2015 Comment • Added Qualification Information table on page 5. • Updated data sheet based on corporate template. IR WORLD HEADQUARTERS: 101 N. Sepulveda Blvd., El Segundo, California 90245, USA To contact International Rectifier, please visit http://www.irf.com/whoto-call/ 5 www.irf.com © 2015 International Rectifier Submit Datasheet Feedback April 24, 2015