PVT322S-T

Series PVT322PbF Microelectronic Power IC HEXFET® Power MOSFET Photovoltaic Relay Dual Pole, Normally Open, 0-250V, 170mA AC/DC General Description The PVT322 Series Photovoltaic Relay is a dual-pole, normally open solid-state relay that can replace electromechanical relays in many applications. It utilizes International Rectifier’s HEXFET power MOSFET as the output switch, driven by an integrated circuit photovoltaic generator of novel construction. The output switch is controlled by radiation from a GaAlAs light emitting diode (LED) which is optically isolated from the photovoltaic generator. Series PVT322 Relays are packaged in an 8-pin, molded DIP package with either thru-hole or surface mount (gull-wing) terminals. It is available in standard plastic shipping tubes or on tape-and-reel. Please refer to Part Identification information opposite. Features  HEXFET® Power MOSFET output  Bounce-free operation  4,000 VRMS I/O isolation  Linear AC/DC operation  Solid-State Reliability  UL recognized and BABT certified   Applications  On/Off Hook switch  Tip and Ring Line switching  General switching Part Identification PVT322PbF PVT322SPbF PVT322S-TPbF thru-hole Surface-mount Surface-mount, Tape and Reel (HEXFET is the registered trademark for International Rectifier Power MOSFETs) 1 2016-08-29 Series PVT322PbF   Electrical Specifications (-40°C TA  +85°C unless otherwise specified)   INPUT CHARACTERISTICS Minimum Control Current (See figure1) Limits 2.0 Units mA 0.4 mA 2.0 to 25 mA 6.0 V Limits Units 0 to ±250 V(DC or AC peak) 170 mA 500 mA 10  1.0 µA 3.0 ms 0.5 ms 50 pF GENERAL CHARACTERISTICS Minimum Dielectric Strength, Input-Output Limits 4000 Units VRMS Minimum Dielectric Strength, Pole-to-Pole 1000 VDC Maximum Control Current for Off-State Resistance @ TA=+25°C Control Current Range (Caution: current limit input LED, see figure 5) Maximum Reverse Voltage OUTPUT CHARACTERISTICS Operating Voltage Range Maximum Load Current @ TA=+40°C 5mA Control (See figure 1) (single and dual channel operation) Maximum Peak Load Current (10ms maximum duration) (single and dual channel operation) Maximum On-State Resistance @TA=+25°C For 50mA Pulsed load, 5mA Control (see figure 3) Maximum Off-State Leakage @TA=+25°C, ±250V (see figure 4) Maximum Turn-On Time @TA=+25°C (see figure 6) For 50mA, 100 VDC load, 5mA Control Maximum Turn-Off Time @TA=+25°C (see figure 6) For 50mA, 100 VDC load, 5mA Control Maximum Output Capacitance @ 50VDC 12  Minimum Insulation Resistance, Input-Output, @TA=+25°C, 50%RH, 100VDC 10 Maximum Capacitance, Input-Output Maximum Pin Soldering Temperature (10 seconds maximum) 1.0 +260 pF Operating -40 to 85 °C Storage -40 to 100 Ambient Temperature Range:   International Rectifier does not recommend the use of this product in aerospace, avionics, military or life support applications. Users of this International Rectifier product in such applications assume all risks of such use and indemnify International Rectifier against all damages resulting from such use. 2 Connection Diagram 2016-08-29 Series PVT322PbF   Figure 1. Typical Current Derating Curve Figure 3. Typical Normalized On-Resistance 3 Figure 2. Linearity Characteristics Figure 4. Typical Normalized Off-State Leakage 2016-08-29 Series PVT322PbF   Figure 5. Input Characteristics (Current Controlled) Figure 7. Delay Time Definitions 4 Figure 6. Typical Delay Times Figure 8. Typical Output Capacitance 2016-08-29 Series PVT322PbF   Case Outline Note: For the most current drawing please refer to IR website at: http://www.irf.com/package/ 5 2016-08-29 Series PVT322PbF   Qualifiction Information†   Industrial (per JEDEC JESD47F† guidelines) Qualification Level   Moisture Sensitivity Level   PVT322PbF PVT322SPbF N/A MSL4 PVT322PbF (per JEDEC J-STD-020E & JEDEC J-STD-033C †) Yes RoHS Compliant   † Applicable version of JEDEC standard at the time of product release. Revision History Date 6/2/2015 8/29/2016 6 Comment  Added Qualification Information Table on page 6.  Updated data sheet based wit new IR corporate template.  Corrected typo from “Single Pole” to “Dual Pole” on page 1.  Updated "Infineon” logo –all pages. Updated disclaimer on last page. 2016-08-29 Series PVT322PbF   Published by Infineon Technologies AG 81726 München, Germany © Infineon Technologies AG 2015 All Rights Reserved. IMPORTANT NOTICE The information given in this document shall in no event be regarded as a guarantee of conditions or characteristics (“Beschaffenheitsgarantie”). With respect to any examples, hints or any typical values stated herein and/or any information regarding the application of the product, Infineon Technologies hereby disclaims any and all warranties and liabilities of any kind, including without limitation warranties of non-infringement of intellectual property rights of any third party. In addition, any information given in this document is subject to customer’s compliance with its obligations stated in this document and any applicable legal requirements, norms and standards concerning customer’s products and any use of the product of Infineon Technologies in customer’s applications. The data contained in this document is exclusively intended for technically trained staff. It is the responsibility of customer’s technical departments to evaluate the suitability of the product for the intended application and the completeness of the product information given in this document with respect to such application. For further information on the product, technology, delivery terms and conditions and prices please contact your nearest Infineon Technologies office (www.infineon.com). WARNINGS Due to technical requirements products may contain dangerous substances. For information on the types in question please contact your nearest Infineon Technologies office. Except as otherwise explicitly approved by Infineon Technologies in a written document signed by authorized representatives of Infineon Technologies, Infineon Technologies’ products may not be used in any applications where a failure of the product or any consequences of the use thereof can reasonably be expected to result in personal injury. 7 2016-08-29