0
登录后你可以
  • 下载海量资料
  • 学习在线课程
  • 观看技术视频
  • 写文章/发帖/加入社区
会员中心
创作中心
发布
  • 发文章

  • 发资料

  • 发帖

  • 提问

  • 发视频

创作活动
S29VS128RABBHW013

S29VS128RABBHW013

  • 厂商:

    CYPRESS(赛普拉斯)

  • 封装:

    VFBGA44

  • 描述:

    IC FLASH MEM 64MBIT 44VTBGA

  • 数据手册
  • 价格&库存
S29VS128RABBHW013 数据手册
S29VS/XS-R MirrorBit® Flash Family S29VS256R, S29VS128R, S29XS256R, S29XS128R 256/128 Megabit (32/16 Megabyte) 1.8 V Burst 16-bit Data Bus, Simultaneous Read/Write, Multiplexed MirrorBit Flash Memory S29VS/XS-R MirrorBit ® Flash Family Cover Sheet Data Sheet (Advance Information) Notice to Readers: This document states the current technical specifications regarding the Spansion product(s) described herein. Each product described herein may be designated as Advance Information, Preliminary, or Full Production. See Notice On Data Sheet Designations for definitions. Publication Number S29VS_XS-R_00 Revision 08 Issue Date July 30, 2012 Da t a Sh e e t ( A d va n ce In for ma t i on ) Notice On Data Sheet Designations Spansion Inc. issues data sheets with Advance Information or Preliminary designations to advise readers of product information or intended specifications throughout the product life cycle, including development, qualification, initial production, and full production. In all cases, however, readers are encouraged to verify that they have the latest information before finalizing their design. The following descriptions of Spansion data sheet designations are presented here to highlight their presence and definitions. Advance Information The Advance Information designation indicates that Spansion Inc. is developing one or more specific products, but has not committed any design to production. Information presented in a document with this designation is likely to change, and in some cases, development on the product may discontinue. Spansion Inc. therefore places the following conditions upon Advance Information content: “This document contains information on one or more products under development at Spansion Inc. The information is intended to help you evaluate this product. Do not design in this product without contacting the factory. Spansion Inc. reserves the right to change or discontinue work on this proposed product without notice.” Preliminary The Preliminary designation indicates that the product development has progressed such that a commitment to production has taken place. This designation covers several aspects of the product life cycle, including product qualification, initial production, and the subsequent phases in the manufacturing process that occur before full production is achieved. Changes to the technical specifications presented in a Preliminary document should be expected while keeping these aspects of production under consideration. Spansion places the following conditions upon Preliminary content: “This document states the current technical specifications regarding the Spansion product(s) described herein. The Preliminary status of this document indicates that product qualification has been completed, and that initial production has begun. Due to the phases of the manufacturing process that require maintaining efficiency and quality, this document may be revised by subsequent versions or modifications due to changes in technical specifications.” Combination Some data sheets contain a combination of products with different designations (Advance Information, Preliminary, or Full Production). This type of document distinguishes these products and their designations wherever necessary, typically on the first page, the ordering information page, and pages with the DC Characteristics table and the AC Erase and Program table (in the table notes). The disclaimer on the first page refers the reader to the notice on this page. Full Production (No Designation on Document) When a product has been in production for a period of time such that no changes or only nominal changes are expected, the Preliminary designation is removed from the data sheet. Nominal changes may include those affecting the number of ordering part numbers available, such as the addition or deletion of a speed option, temperature range, package type, or VIO range. Changes may also include those needed to clarify a description or to correct a typographical error or incorrect specification. Spansion Inc. applies the following conditions to documents in this category: “This document states the current technical specifications regarding the Spansion product(s) described herein. Spansion Inc. deems the products to have been in sufficient production volume such that subsequent versions of this document are not expected to change. However, typographical or specification corrections, or modifications to the valid combinations offered may occur.” Questions regarding these document designations may be directed to your local sales office. 2 S29VS/XS-R MirrorBit® Flash Family S29VS_XS-R_00_08 July 30, 2012 S29VS/XS-R MirrorBit® Flash Family S29VS256R, S29VS128R, S29XS256R, S29XS128R 256/128 Megabit (32/16 Megabyte) 1.8 V Burst 16-bit Data Bus, Simultaneous Read/Write, Multiplexed MirrorBit Flash Memory Data Sheet (Advance Information) Features  Single 1.8 V supply for read/program/erase (1.70–1.95 V)  10-year data retention (typical)  65 nm MirrorBit Technology  Cycling Endurance: 100,000 cycles per sector (typical)  Address and Data Interface Options  RDY output indicates data available to system – Address and Data Multiplexed for reduced I/O count (ADM) S29VS-R – Address-High, Address-Low, Data Multiplexed for minimum I/O count (AADM) S29XS-R  Simultaneous Read/Write operation  Command set compatible with JEDEC (42.4) standard  Hardware sector protection via VPP pin  Handshaking by monitoring RDY  Offered Packages – 44-ball FBGA (6.2 mm x 7.7 mm x 1.0 mm)  32-word Write Buffer  Low VCC write inhibit  Bank architecture – Eight-bank  Four 32-KB sectors at the top or bottom of memory array 255/127 of 128-KB sectors  Programmable linear (8/16-word) with wrap around and continuous burst read modes  Secured Silicon Sector region consisting of 128 words each for factory and customer  Write operation status bits indicate program and erase operation completion  Suspend and Resume commands for Program and Erase operations  Asynchronous program operation, independent of burst control register settings  VPP input pin to reduce factory programming time  Support for Common Flash Interface (CFI) General Description The Spansion S29VS256/128R and S29XS256/128R are MirrorBit® Flash products fabricated on 65 nm process technology. These burst mode Flash devices are capable of performing simultaneous read and write operations with zero latency on two separate banks using multiplexed data and address pins. These products can operate up to 108 MHz and use a single VCC of 1.7 V to 1.95 V that makes them ideal for the demanding wireless applications of today that require higher density, better performance, and lowered power consumption. The S29VS256/128R operates in ADM mode, while the S29XS256/128R can operate in the AADM mode. Performance Characteristics Read Access Times Speed Option (MHz) Current Consumption (typical values) 108 Continuous Burst Read @ 108 MHz 32 mA Max. Synch. Latency, ns (tIA) 72.34 Simultaneous Operation @ 108 MHz 71 mA Max. Synch. Burst Access, ns (tBACC) 6.75 Program/Erase 30 mA Max. Asynch. Access Time, ns (tACC) 80 Standby Mode 30 µA Max OE# Access Time, ns (tOE) 15 Typical Program & Erase Times Single Word Programming 170 µs Effective Write Buffer Programming (VCC) Per Word 14.1 µs Effective Write Buffer Programming (VPP) Per Word Publication Number S29VS_XS-R_00 9 µs Sector Erase (16 Kword Sector) 350 ms Sector Erase (64 Kword Sector) 800 ms Revision 08 Issue Date July 30, 2012 This document contains information on one or more products under development at Spansion Inc. The information is intended to help you evaluate this product. Do not design in this product without contacting the factory. Spansion Inc. reserves the right to change or discontinue work on this proposed product without notice. Da t a Sh e e t ( A d va n ce In for ma t i on ) Table of Contents Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 General Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Performance Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 4 1. Ordering Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 1.1 Valid Combinations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 2. Input/Output Descriptions & Logic Symbol. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 3. Block Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 4. Physical Dimensions/Connection Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 4.1 Related Documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 4.2 Special Handling Instructions for FBGA Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 5. Product Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 6. Address Space Maps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.1 Data Address & Quantity Nomenclature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.2 Flash Memory Array. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.3 Address/Data Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.4 Bus Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.5 Device ID and CFI (ID-CFI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 14 15 17 18 19 7. Device Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.1 Asynchronous Read. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.2 Synchronous (Burst) Read Mode and Configuration Register . . . . . . . . . . . . . . . . . . . . . . . . 7.3 Status Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.4 Blank Check. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.5 Simultaneous Read/Write . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.6 Writing Commands/Command Sequences . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.7 Program/Erase Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.8 Handshaking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.9 Hardware Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.10 Software Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 22 22 28 31 31 32 32 38 39 39 8. Sector Protection/Unprotection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.1 Sector Lock/Unlock Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.2 Sector Lock Range Command. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.3 Hardware Data Protection Methods. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.4 SSR Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.5 Secure Silicon Region . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 39 40 40 41 41 9. Power Conservation Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9.1 Standby Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9.2 Automatic Sleep Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9.3 Output Disable (OE#). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 43 43 43 10. Electrical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.1 Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.2 Operating Ranges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.3 DC Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.4 Capacitance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.5 AC Test Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.6 Key to Switching Waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.7 VCC Power Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.8 CLK Characterization. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.9 AC Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 44 44 45 46 46 46 47 47 48 11. Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56 11.1 Command Definitions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56 11.2 Device ID and Common Flash Memory Interface Address Map . . . . . . . . . . . . . . . . . . . . . . 58 12. Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70 S29VS/XS-R MirrorBit® Flash Family S29VS_XS-R_00_08 July 30, 2012 Dat a S he e t ( Ad van ce I nfor m at i on ) Figures Figure 3.1 Figure 4.1 Figure 4.2 Figure 7.1 Figure 10.1 Figure 10.2 Figure 10.3 Figure 10.4 Figure 10.5 Figure 10.6 Figure 10.7 Figure 10.8 Figure 10.9 Figure 10.10 Figure 10.11 Figure 10.12 Figure 10.13 Figure 10.14 Figure 11.1 Figure 11.2 Figure 11.3 Figure 11.4 Figure 11.5 Figure 11.6 Figure 11.7 Figure 11.8 Figure 11.9 Figure 11.10 Figure 11.11 Figure 11.12 Figure 11.13 July 30, 2012 S29VS_XS-R_00_08 Simultaneous Operation Circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 44-Ball Very Thin Fine-Pitch Ball Grid Array, Top View, Balls Facing Down . . . . . . . . . . . . . 10 VDJ044—44-Ball Very Thin Fine-Pitch Ball Grid Array . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Synchronous Read . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Maximum Negative Overshoot Waveform . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 Maximum Positive Overshoot Waveform . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 Input Pulse and Test Point. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 Output Load . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 VCC Power-up Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 CLK Characterization. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 Synchronous Read Mode - ADM Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 Asynchronous Mode Read - ADM Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 Asynchronous Program Operation Timings - ADM Interface. . . . . . . . . . . . . . . . . . . . . . . . . 50 Reset Timings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 Latency with Boundary Crossing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 Latency with Boundary Crossing into Bank Performing Embedded Operation . . . . . . . . . . . 52 Example of Programmable Wait States . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 Back-to-Back Read/Write Cycle Timings - ADM Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 Asynchronous Read - AADM Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63 Asynchronous Read Followed By Read - AADM Interface . . . . . . . . . . . . . . . . . . . . . . . . . . .63 Asynchronous Read Followed By Write - AADM Interface . . . . . . . . . . . . . . . . . . . . . . . . . . .64 Asynchronous Write - AADM Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64 Asynchronous Write Followed By Read - AADM Interface . . . . . . . . . . . . . . . . . . . . . . . . . . .65 Asynchronous Write Followed By Write - AADM Interface . . . . . . . . . . . . . . . . . . . . . . . . . . .65 Synchronous Read Wrapped Burst Address Low Only - AADM Interface . . . . . . . . . . . . . . .66 Synchronous Read Continuous Burst - AADM Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . .66 Synchronous Read Wrapped Burst - AADM Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67 Synchronous Read Followed By Read Burst - AADM Interface . . . . . . . . . . . . . . . . . . . . . . .67 Synchronous Read Followed By Write - AADM Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . .68 Synchronous Write Followed By Read Burst - AADM Interface . . . . . . . . . . . . . . . . . . . . . . .68 Synchronous Write Followed By Write - AADM Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . .69 S29VS/XS-R MirrorBit® Flash Family 5 Da t a Sh e e t ( A d va n ce In for ma t i on ) Tables Table 2.1 Table 6.1 Table 6.2 Table 6.3 Table 6.4 Table 6.5 Table 6.6 Table 6.7 Table 6.8 Table 7.1 Table 7.2 Table 7.3 Table 7.4 Table 7.5 Table 7.6 Table 7.7 Table 7.8 Table 7.9 Table 7.10 Table 7.11 Table 7.12 Table 7.13 Table 7.14 Table 7.15 Table 7.16 Table 7.17 Table 7.18 Table 7.19 Table 7.20 Table 7.21 Table 7.22 Table 7.23 Table 7.24 Table 7.25 Table 7.26 Table 7.27 Table 7.28 Table 8.1 Table 8.2 Table 8.3 Table 10.1 Table 10.2 Table 11.1 Table 11.2 6 Input/Output Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 System Versus Flash View of Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15 S29VS/XS256R Sector and Memory Address Map (Top Boot) . . . . . . . . . . . . . . . . . . . . . . .15 S29VS/XS256R Sector and Memory Address Map (Bottom Boot) . . . . . . . . . . . . . . . . . . . . .15 S29VS/XS128R Sector and Memory Address Map (Top Boot) . . . . . . . . . . . . . . . . . . . . . . .16 S29VS/XS128R Sector and Memory Address Map (Bottom Boot) . . . . . . . . . . . . . . . . . . . . .16 Device Bus Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18 ID-CFI Address Map Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19 Secured Silicon Region . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20 Initial Wait State vs. Frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23 Address Latency for 10 -13 Wait States . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23 Address Latency for 9 Wait States . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23 Address Latency for 8 Wait States . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24 Address Latency for 7 Wait States . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24 Address Latency for 6 Wait States . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24 Address Latency for 5 Wait States . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24 Address Latency for 4 Wait States . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25 Address Latency for 3 Wait States . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25 Burst Address Groups . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25 Configuration Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27 Status Register Reset State . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28 Status Register - Bit 7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28 Status Register - Bit 6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29 Status Register - Bit 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29 Status Register - Bit 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29 Status Register - Bit 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30 Status Register - Bit 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30 Status Register - Bit 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30 Status Register - Bit 0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31 Write Buffer Program . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34 Program Suspend . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35 Program Resume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35 Sector Erase . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36 Chip Erase . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37 Erase Suspend . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38 Erase Resume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38 Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39 Secured Silicon Region Entry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42 Secured Silicon Region Program . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42 Secured Silicon Region Exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42 VCC Power-up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47 Warm-Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51 Command Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56 ID/CFI Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58 S29VS/XS-R MirrorBit® Flash Family S29VS_XS-R_00_08 July 30, 2012 Dat a 1. S he e t ( Ad van ce I nfor m at i on ) Ordering Information The ordering part number is formed by a valid combination of the following: S29VS 256 R xx BH W 00 0 Packing Type 0 = Tray (standard; see note (Note 1)) 3 = 13-inch Tape and Reel Model Number 00 = Top 01 = Bottom Temperature Range W = Wireless (–25°C to +85°C) Package Type and Material BH = Very Thin Fine-Pitch BGA, Low Halogen Lead (Pb)-Free Package Speed Option (Burst Frequency) 0S = 83 MHz AA = 104 MHz AB = 108 MHz Process Technology R = 65 nm MirrorBit® Technology Flash Density 256 = 256 Mb 128 = 128 Mb Device Family S29VS256R =1.8 Volt-only Simultaneous Read/Write, Burst-Mode Address and Data Multiplexed Flash Memory S29XS256R =1.8 Volt-only Simultaneous Read/Write, Burst-Mode Address Low, Address High and Data Multiplexed Flash Memory 1.1 Valid Combinations Valid Combination list configurations are planned to be supported in volume for this device. Consult your local sales office to confirm availability of specific valid combinations and to check on newly released combinations. S29VS-R Valid Combinations (1) (2) Base Ordering Part Number Speed Option Package Type, Material, and Temperature Range Packing Type Model Numbers Package Type (2) 0S, AA, AB BHW (3) 0, 3 (1) 00, 01 6.2 mm x 7.7 mm, 44-ball S29VS256R S29VS128R S29XS256R S29XS128R Notes: 1. Type 0 is standard. Specify other options as required. 2. BGA package marking omits leading S29 and packing type designator from ordering part number. 3. Industrial Temperature Range is also available. For device specification differences, please refer to the Specification Supplement with Publication Number S29VS_XS-R_SP. July 30, 2012 S29VS_XS-R_00_08 S29VS/XS-R MirrorBit® Flash Family 7 Da t a 2. Sh e e t ( A d va n ce In for ma t i on ) Input/Output Descriptions & Logic Symbol Table 2.1 identifies the input and output package connections provided on the device. Table 2.1 Input/Output Descriptions Symbol Type Amax – A16 A/DQ15 – A/DQ0 I/O CE# Input Flash Chip Enable. Asynchronous relative to CLK. OE# Input Output Enable. Asynchronous relative to CLK for the Burst mode. WE# Input Write Enable VCC Supply Device Power Supply VCCQ Supply Input/Output Power Supply (must be ramped simultaneously with VCC) VSS I/O Ground VSSQ I/O Input/Output Ground NC No Connect No Connected internally RDY Output Ready. Indicates when valid burst data is ready to be read Input The first rising edge of CLK in conjunction with AVD# low latches address input and activates burst mode operation. After the initial word is output, subsequent rising edges of CLK increment the internal address counter. CLK should remain low during asynchronous access AVD# Input Address Valid input. Indicates to device that the valid address is present on the address inputs (address bits A15 – A0 are multiplexed, address bits Amax – A16 are address only). VIL = for asynchronous mode, indicates valid address; for burst mode, cause staring address to be latched on rising edge of CLK. VIH = device ignores address inputs RESET# Input Hardware Reset. Low = device resets and returns to reading array data. VPP Input Accelerated input. At VHH, accelerates programming; automatically places device in unlock bypass mode. At VIL, disables all program and erase functions. Should be at VIH for all other conditions. RFU Reserved Reserved for future use CLK 8 Description Higher order address lines. Amax = A23 for VS256R, A22 for VS128R. On the XS256R and XS128R, these inputs can be left unconnected in AADM mode. Multiplexed Address/Data input/output S29VS/XS-R MirrorBit® Flash Family S29VS_XS-R_00_08 July 30, 2012 Dat a 3. S he e t ( Ad van ce I nfor m at i on ) Block Diagrams Figure 3.1 Simultaneous Operation Circuit Bank Address Bank 0 Latches and Control Logic VSS VSSQ Y-Decoder VCC DQ15–DQ0 Amax–A0 X-Decoder OE# VPP RESET# WE# CE# AVD# RDY Bank 1 Latches and Control Logic Y-Decoder Bank Address DQ15–DQ0 X-Decoder Amax–A0 STATE CONTROL & COMMAND REGISTER DQ15–DQ0 Status Control Amax–A0 DQ15–DQ0 Bank (n-1) Latches and Control Logic Bank Address Amax–A0 Y-Decoder X-Decoder DQ15–DQ0 Bank (n) Latches and Control Logic Bank Address Y-Decoder X-Decoder DQ15–DQ0 Notes: 1. Amax = A23 for S29VS/XS256R, A22 for S29VS/XS128R. 2. Bank(n) = 8 (S29VS/XS256/128R). July 30, 2012 S29VS_XS-R_00_08 S29VS/XS-R MirrorBit® Flash Family 9 Da t a 4. Sh e e t ( A d va n ce In for ma t i on ) Physical Dimensions/Connection Diagrams This section shows the I/O designations and package specifications for the S29VS-R. 4.1 Related Documents The following documents contain information relating to the S29VS-R devices. Click on the title or go to www.spansion.com, or request a copy from your sales office.  Considerations for X-ray Inspection of Surface-Mounted Flash Integrated Circuits 4.2 Special Handling Instructions for FBGA Package Special handling is required for Flash Memory products in FBGA packages. Flash memory devices in FBGA packages may be damaged if exposed to ultrasonic cleaning methods. The package and/or data integrity may be compromised if the package body is exposed to temperatures above 150°C for prolonged periods of time. 4.2.1 44-Ball Very Thin Fine-Pitch Ball Grid Array, S29VS256R/S29XS256R/ S29VS128R/S29XS128R Figure 4.1 44-Ball Very Thin Fine-Pitch Ball Grid Array, Top View, Balls Facing Down 1 2 3 4 5 6 7 8 9 10 11 12 13 14 A NC NC B C RDY A21 VSS CLK VCC WE# VPP A19 A17 A22 VCCQ A16 A20 AVD# A23 RESET# NC A18 CE# VSSQ VSS A/DQ7 A/DQ6 A/DQ13 A/DQ12 A/DQ3 A/DQ2 A/DQ9 A/DQ8 OE# A/DQ15 A/DQ14 VSSQ A/DQ5 A/DQ11 A/DQ10 VCCQ A/DQ1 A/DQ0 D E F A/DQ4 G H NC NC Notes: 1. Ball D7 is NC for S29VS128R. 2. Balls D7, C12, C4, D5, C10, D10, C11, D4 are NC for S29XS256R and S29XS128R 10 S29VS/XS-R MirrorBit® Flash Family S29VS_XS-R_00_08 July 30, 2012 Dat a 4.2.2 S he e t ( Ad van ce I nfor m at i on ) VDJ044-44-Ball Very Thin Fine-Pitch Ball Grid Array, 6.2mm x 7.7 mm Figure 4.2 VDJ044—44-Ball Very Thin Fine-Pitch Ball Grid Array NOTES: PACKAGE VDJ 044 JEDEC 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M-1994. N/A 2. ALL DIMENSIONS ARE IN MILLIMETERS. 7.70 mm x 6.20 mm NOM PACKAGE 3. BALL POSITION DESIGNATION PER JESD 95-1, SPP-010 EXCEPT AS NOTED). SYMBOL MIN NOM MAX NOTE A 0.86 0.93 1.00 OVERALL THICKNESS A1 0.18 0.23 0.28 BALL HEIGHT A2 0.64 0.71 0.78 BODY THICKNESS D 7.60 7.70 7.80 BODY SIZE E 6.10 6.20 6.30 BODY SIZE D1 4.50 BSC. BALL FOOTPRINT E1 1.50 BSC. BALL FOOTPRINT MD 10 ROW MATRIX SIZE D DIRECTION ME 4 ROW MATRIX SIZE E DIRECTION N 44 Øb 0.25 0.30 TOTAL BALL COUNT 0.35 BALL DIAMETER e 0.50 BSC. BALL PITCH SD / SE 0.25 BSC. SOLDER BALL PLACEMENT DEPOPULATED SOLDER BALLS 4. e REPRESENTS THE SOLDER BALL GRID PITCH. 5. SYMBOL "MD" IS THE BALL ROW MATRIX SIZE IN THE "D" DIRECTION. SYMBOL "ME" IS THE BALL COLUMN MATRIX SIZE IN THE "E" DIRECTION. N IS THE TOTAL NUMBER OF SOLDER BALLS. 6 DIMENSION "b" IS MEASURED AT THE MAXIMUM BALL DIAMETER IN A PLANE PARALLEL TO DATUM C. 7 SD AND SE ARE MEASURED WITH RESPECT TO DATUMS A AND B AND DEFINE THE POSITION OF THE CENTER SOLDER BALL IN THE OUTER ROW. WHEN THERE IS AN ODD NUMBER OF SOLDER BALLS IN THE OUTER ROW PARALLEL TO THE D OR E DIMENSION, RESPECTIVELY, SD OR SE = 0.000. WHEN THERE IS AN EVEN NUMBER OF SOLDER BALLS IN THE OUTER ROW, SD OR SE = e/2 8. NOT USED. 9. "+" INDICATES THE THEORETICAL CENTER OF DEPOPULATED BALLS. 10 A1 CORNER TO BE IDENTIFIED BY CHAMFER, LASER OR INK MARK, METALLIZED MARK INDENTATION OR OTHER MEANS. 3616 \ 16-039.27 \ 12.5.6 July 30, 2012 S29VS_XS-R_00_08 S29VS/XS-R MirrorBit® Flash Family 11 Da t a 5. Sh e e t ( A d va n ce In for ma t i on ) Product Overview The S29VS/XS-R family is 1.8-V only, simultaneous read/write, burst-mode, Flash devices. These devices have a 16 bit (word) wide data bus. All read accesses provide 16 bits of data on each bus transfer cycle. All writes take 16 bits of data from each bus transfer cycle. Device Mbits Mbytes Mwords Banks Mbytes / Bank S29VS128R/S29XS128R 128 16 8 8 2 S29VS256R/S29XS256R 256 32 16 8 4 The Flash memory array is divided into banks. A bank is the address range within which one program, or erase operation may be in progress at the same time as one read operation is in progress in any other bank of the memory. This multiple bank structure enables Simultaneous Read and Write (SRW) so that code may be executed or data read from one bank while a group of data is programmed, or erased as a background task in one other bank. Each bank is divided into sectors. A sector is the minimum address range of data which can be erased to an all Ones state. Most of the sectors are 128 KBytes each. Depending on the option ordered, either the top-4 sectors or the bottom-4 sectors are 32 KBytes each. These are called boot sectors because they are often used for holding boot code or parameters that need to be protected or erased separately from other data in the Flash array. Programming is done via a 64 Byte write buffer. It is possible to program from one to 32 words (64 bytes) in each programming operation. The S29VS/XS family is capable of continuous, synchronous (burst) read or linear read (8- or 16-word aligned group) with wrap around. A wrapped burst begins at the initial location and continues to the end of an 8, or 16-word aligned group then “wraps-around” to continue at the beginning of the 8, or 16-word aligned group. The burst completes with the last word before the initial location. Word wrap around burst is generally used for processor cache line fill. 12 S29VS/XS-R MirrorBit® Flash Family S29VS_XS-R_00_08 July 30, 2012 Dat a 6. S he e t ( Ad van ce I nfor m at i on ) Address Space Maps There are five address spaces within each device:  A Non-Volatile Flash Memory Array used for storage of data that may be randomly accessed by asynchronous or burst read operations.  A Read Only Memory Array used for factory programmed permanent device characteristics information. This area contains the Device Identification (ID) and Common Flash Interface (CFI) information.  A One Time Programmable (OTP) Non-volatile Flash array used for factory programmed permanent data, and customer programmable permanent data. This is called the Secure Silicon Region (SSR).  An OTP location used to permanently protect the SSR. This is call the SSR Lock.  A volatile register used to configure device behavior options. This is called the Configuration Register. The main Flash Memory Array is the primary and default address space but, it may be partially overlaid by the other four address spaces with one alternate address space available at any one time. The location where the alternate address space is overlaid is defined by the address provided in the command that enables each overlay. The portion of the command address that is sufficient to select a sector is used to select the sector that is overlaid by an alternate Address Space Overlay (ASO). Any address range, within the overlaid sector, not defined by an overlay address map, is reserved for future use. All read accesses outside of an address map within the selected sector, return non-valid data. The locations will display actively driven data but the meaning of whatever ones or zeros appear are not defined. There are three operation modes for each bank that determine what portions of the address space are readable at any given time:  Read Mode  Embedded Algorithm (EA) Mode  Address Space Overlay (ASO) Mode Each bank of the device can be in any operation mode but, only one bank can be in EA or ASO mode at any one time. In Read Mode, a Flash Memory Array bank may be directly read by asynchronous or burst accesses from the host system bus. The Control Unit (CU) puts all banks in Read mode during Power-on, a Hardware Reset, after a Command Reset, or after a bank is returned to Read mode from EA mode. In EA mode the Flash memory array data in a bank is stable but undefined, and effectively unavailable for read access from the host system. While in EA mode the bank is used by the CU in the execution of commands. Typical EA mode operations are programming or erasing of data in the Flash array. All other banks are available for read access while the one bank is in EA mode. This ability to read from one bank while another bank is used in the execution of a command is called Simultaneous Read and Write (SRW) and allows for continued operation of the system via the reading of data or execution of code from other banks while one bank is programming or erasing data as a relatively long time frame background task. In ASO mode, one of the overlay address spaces are overlaid in a bank (entered). That bank is in ASO mode and no other bank may be in EA or ASO mode. All EA activity must be completed before entering any ASO mode. A command for entering an EA or ASO mode while another bank is in EA or ASO mode will be ignored. While an ASO mode is active (entered) in a bank, a read for Flash array data to any other bank is allowed. ASO mode selects a specific sector for the overlaid address space. Other sectors in the ASO bank still provide Flash array data and may be read during ASO mode. The ASOs are functionally tied to the lowest address bank. The commands used to overlay (enter) these areas must select a sector address within the lowest address bank. While SSR Lock, SSR, or Configuration Register is overlaid only the SSR Lock, SSR, or Configuration Register respectively may be programmed in the overlaid sector. While any of these ASO areas are being programmed the ASO bank switches to EA mode. The ID/CFI and factory portion of the SSR ASO is not customer programmable. The address nomenclature used in this document is a shorthand form that shows addresses are formed from a concatenation of high order bits, sufficient to select a Sector Address (SA), with low order bits to select a location within the sector. When in Read mode and reading from the Flash Array the entire address is used to July 30, 2012 S29VS_XS-R_00_08 S29VS/XS-R MirrorBit® Flash Family 13 Da t a Sh e e t ( A d va n ce In for ma t i on ) select a specific word for asynchronous read or the starting word address of a burst read. When writing a command, the address bits between SA and the command specified least significant bits must be Zero to allow for future extension of an overlay address map. 6.1 Data Address & Quantity Nomenclature A Bit is a single One or Zero data value. A Byte is a group of 8 bits aligned on an 8 bit boundary. A Word is a group of 16 bits aligned on a 16 bit boundary. Throughout this document quantities of data are generally expressed in terms of byte units. Example: most sectors have 128 Kilo Bytes of data and is written as 128 KBytes or 128 KB. Addresses are also expressed in byte units. A 128 KByte sector has an address range from 00000h to 1FFFFh Byte locations. Byte units are used because most host systems and software for these systems use byte resolution addresses. Software & hardware developers most often calculate code and data sizes in terms of bytes, so this is more familiar terminology than describing data sizes in bits or words. In general, data units will not be abbreviated if possible so that full unit names of Byte, Word, or bit are used. However, there may be cases where capital B is used for byte units and lower case b is used for bit units, in situations where space is limited such as in table column headers. In some cases data quantities will also be expressed in word or bit units in addition to the quantity shown in bytes. This may be done as an aid to readers familiar with prior device generation documentation which often provided only word or bit unit values. Word units may also be used to emphasize that, in the memory devices described in this documentation, data is always exchanged with the host system in word units. Each bus cycle transfer of read or write data on the host system bus is a transfer 16 bits of data. A read bus cycle is always a16 bit wide transfer of data to the host system whether the host system chooses to look at all the bits or not. A write bus cycle is always a transfer of 16 bits to the memory device and the device will store all 16 bits to a register. In the case of a program operation all 16 bits of each word to be programmed will be stored in the Flash array. Because data is always transferred in word units, the memory devices being discussed use only the address signals from the system necessary to select words. The host system byte address uses system address a0 to select bytes and a1 to select words. Flash memories with word wide data paths have traditionally started their address signal numbering with A0 being the selector for words because a byte select input is not needed. So, system address a-maximum to a1 are connected to Flash A-maximum to A0 (the documentation convention here is to use lower case for system address signal numbering and upper case for Flash address signals). In prior generation Flash documentation, address values used in commands to the flash were documented from the viewpoint of the Flash device - the bit pattern appearing on Flash address inputs A10 to A0. However, most software is written with addresses expressed in bytes. This means the address patterns shown in Flash command tables have traditionally been shifted by one bit to express them as byte address values in Flash control programs. Example: a prior generation Flash data sheet would show a command write of data value xxA0h to address 555h; this is an address pattern of 10101010101b on Flash address inputs A10 to A0; but software would define this as a byte address value of AAAh since the least significant address bit is not used by the Flash); which is 101010101010b on system address bus a11 to a0. Because system a11 to a1 is connected to Flash A10 to A0 the Flash word address of 555h and the system byte address of AAAh provides the same bit pattern on the same address inputs. Because all address values are being documented as system byte addresses, that are more familiar to software writers, the command tables have addresses that are shifted from those shown in prior generation devices. 14 S29VS/XS-R MirrorBit® Flash Family S29VS_XS-R_00_08 July 30, 2012 Dat a 6.2 S he e t ( Ad van ce I nfor m at i on ) Flash Memory Array The Non-Volatile Flash Memory Array is organized as shown in the following tables. Devices are factory configured to have either all uniform size sectors or four smaller sectors at either the top of the device. Table 6.1 System Versus Flash View of Address System Address Signals a11 a10 1 0 System Byte Address Hex Binary Pattern a9 a8 a7 a6 1 0 1 0 A Flash Word Address Hex A10 a4 a3 a2 1 0 1 a0 0 1 0 A1 A0 A 5 A9 a1 A 5 Flash Address Signals a5 A8 A7 A6 5 A5 A4 A3 A2 Table 6.2 S29VS/XS256R Sector and Memory Address Map (Top Boot) 224 Sector Size (KByte) Bank 128 Sector Range Address Range (word) Address Range (byte) 0 SA000-SA031 000000h–1FFFFFh 000000h–3FFFFFh 1 SA032–SA063 2 SA064–SA095 3 SA096–SA127 4 SA128–SA159 5 SA160–SA191 SA192–SA223 … … … … … … Sector Count … … … … … … Bank Size (Mbit) SA224–SA254 E00000h–FEFFFFh 1C00000h–1FDFFFFh SA255 FF0000h–FF3FFFh 1FE0000h–1FE7FFFh SA256 FF4000h-FF7FFFh 1FE8000h-1FEFFFFh SA257 FF8000h–FFBFFFh 1FF0000h–1FF7FFFh SA258 FFC000h–FFFFFFh 1FF8000h–1FFFFFFh 32 6 31 4 128 7 32 Notes Sector Starting Address – Sector Ending Address Note: All tables have been condensed to show sector-related information for an entire device on a single page. Sectors and their address ranges that are not explicitly listed (such as SA008–SA009) have sector starting and ending addresses that form the same pattern as all other sectors of that size. For example, all 128 KB sectors have the byte address pattern x000000h–x1FFFFh. Table 6.3 S29VS/XS256R Sector and Memory Address Map (Bottom Boot) Bank Size (Mbit) Sector Count 4 Sector Size (Kbyte) Bank Address Range (word) Address Range (byte) SA000 000000h–003FFFh 000000h–007FFFh SA001 004000h–007FFFh 008000h–00FFFFh 010000h–017FFFh 00C000h–00FFFFh 018000h–01FFFFh SA004–SA034 010000h–1FFFFFh 020000h–3FFFFFh 1 SA035–SA066 2 SA067–SA098 3 SA099–SA130 4 SA131–SA162 5 SA163–SA194 6 SA195–SA226 … … … … … … 008000h–00BFFFh SA003 … … … … … … 128 SA002 7 SA227–SA258 E00000h–FFFFFFh 1C00000h–1FFFFFFh 32 224 Notes 32 0 31 Sector Range 128 Sector Starting Address – Sector Ending Address Note: All tables have been condensed to show sector-related information for an entire device on a single page. Sectors and their address ranges that are not explicitly listed (such as SA008–SA009) have sector starting and ending addresses that form the same pattern as all other sectors of that size. For example, all 128 KB sectors have the byte address pattern x000000h–x1FFFFh. July 30, 2012 S29VS_XS-R_00_08 S29VS/XS-R MirrorBit® Flash Family 15 Da t a Sh e e t ( A d va n ce In for ma t i on ) Sector Count 112 Sector Size (KByte) 128 Bank Sector Range Address Range (word) Address Range (byte) 0 SA000-SA015 000000h–0FFFFFh 000000h–1FFFFFh 1 SA016–SA031 2 SA032–SA047 3 SA048–SA063 4 SA064–SA079 5 SA080–SA095 6 SA096–SA111 … … … … … … Bank Size (Mbit) … … … … … … Table 6.4 S29VS/XS128R Sector and Memory Address Map (Top Boot) SA112–SA126 700000h–7EFFFFh E00000h–FDFFFFh SA127 7F0000h–7F3FFFh FE0000h–FE7FFFh SA128 7F4000h-7F7FFFh FE8000h-FEFFFFh SA129 7F8000h–7FBFFFh FF0000h–FF7FFFh SA130 7FC000h–7FFFFFh FF8000h–FFFFFFh 16 15 128 7 4 Notes Sector Starting Address – Sector Ending Address 32 Note: All tables have been condensed to show sector-related information for an entire device on a single page. Sectors and their address ranges that are not explicitly listed (such as SA008–SA009) have sector starting and ending addresses that form the same pattern as all other sectors of that size. For example, all 128 KB sectors have the byte address pattern x000000h–x1FFFFh. Table 6.5 S29VS/XS128R Sector and Memory Address Map (Bottom Boot) Bank Size (Mbit) Sector Count 4 Sector Size (Kbyte) Bank Address Range (word) Address Range (byte) SA000 000000h–003FFFh 000000h–007FFFh SA001 004000h–007FFFh 008000h–00FFFFh SA002 008000h–00BFFFh 010000h–017FFFh SA003 00C000h–00FFFFh 018000h–01FFFFh SA004–SA018 010000h–0FFFFFh 020000h–1FFFFFh 1 SA019–SA034 2 SA035–SA050 3 SA051–SA066 4 SA067–SA082 5 SA083–SA098 6 SA099–SA114 … … … … … … … … … … … … 128 7 SA115–SA130 700000h–7FFFFFh E00000h–FFFFFFh 16 112 Notes 32 0 15 Sector Range 128 Sector Starting Address – Sector Ending Address Note: All tables have been condensed to show sector-related information for an entire device on a single page. Sectors and their address ranges that are not explicitly listed (such as SA008–SA009) have sector starting and ending addresses that form the same pattern as all other sectors of that size. For example, all 128 KB sectors have the byte address pattern x000000h–x1FFFFh. 16 S29VS/XS-R MirrorBit® Flash Family S29VS_XS-R_00_08 July 30, 2012 Dat a 6.3 S he e t ( Ad van ce I nfor m at i on ) Address/Data Interface There are two options for connection to the address and data buses.  Address and Data Multiplexed (ADM) mode. On the S29VS-R devices, the upper address is supplied on separate signal inputs and the lower 16-bits of address are multiplexed with 16-bit data on the A/DQ15 to A/DQ0 I/Os.  Address-high, Address-low, and Data Multiplexed (AADM) mode. On the S29XS-R devices, the upper and lower address are multiplexed with 16-bit data on the A/DQ15 to A/D0 signal I/Os. The two options allow use with the traditional address/data multiplexed NOR interface (S29NS family), or an address multiplexed/data multiplexed interface with the lowest signal count. 6.3.1 ADM Interface (S29VS256R and S29VS128R) A number of processors use ADM interface as a way to reduce pin count. The system permanently connects the upper address bits (A[MAX:16] to the device. When AVD# is LOW it connects A[15:0] to DQ[15:0]. The address is latched on the rising edge of AVD#. When AVD# is HIGH, the system connects the data bus to DQ[15:0]. This results in 16-pin savings from the traditional Address and Data in Parallel (ADP) interface. 6.3.2 AADM Interface (S29XS256R and S29XS128R) Signal input and output (I/O) connections on a high complexity component such as an Application Specific Integrated Circuit (ASIC) are a limited resource. Reducing signal count on any interface of the ASIC allows for either more features or lower package cost. The memory interface described in this section is intended to reduce the I/O signal count associated with the Flash memory interface with an ASIC. The interface is called Address-High, Address-Low, and Data Multiplexed (AADM) because all address and data information is time multiplexed on a single 16-bit wide bus. This interface is electrically compatible with existing ADM 16-bit wide random access static memory interfaces but uses fewer address signals. In that sense AADM is a signal count subset of existing static memory interfaces. This interface can be implemented in existing memory controller designs, as an additional mode, with minimal changes. No new I/O technology is needed and existing memory interfaces can continue to be supported while the electronics industry adopts this new interface. ASIC designers can reuse the existing memory address signals above A15 for other functions when an AADM memory is in use. By breaking up the memory address in to two time slots the address is naturally extended to be a 32-bit word address. But, using two bus cycles to transfer the address increases initial access latency by increasing the time address is using the bus. However, many memory accesses are to locations in memory nearby the previous access. Very often it is not necessary to provide both cycles of address. This interface stores the high half of address in the memory so that if the high half of address does not change from the previous access, only the low half of address needs to be sent on the bus. If a new upper address is not captured at the beginning of an access the last captured value of the upper address is used. This allows accesses within the same 128-KByte address range to provide only the lower address as part of each access. In AADM mode two signal rising edges are needed to capture the upper and lower address portions in asynchronous mode or two signal combinations over two clocks is needed in synchronous mode. In asynchronous mode the upper address is captured by an AVD# rising edge when OE# is Low; the lower address is captured on the rising edge of AVD# with OE# High. In synchronous mode the upper address is captured at the rising clock edge when AVD# and OE# are Low; the lower address is captured at the rising edge of clock when AVD# is Low and OE# is High. CE# going High at any time during the access or OE# returning High after RDY is first asserted High during an access, terminates the read access and causes the address/data bus direction to switch back to input mode. The address/data bus direction switches from input to output mode only after an Address-Low capture when AVD# is Low and OE# is High. This prevents the assertion of OE# during Address-High capture from causing a bus conflict between the host address and memory data signals. Note, in burst mode, this implies at least one cycle of CE# or OE# High before an Address-high for a new access may be placed on the bus so that there is time for the memory to recognize the end of the previous access, stop driving data outputs, and ignore OE# so that assertion of OE# with the new Address-high does not create a bus conflict with a new address being driven on the bus. At high bus frequencies more than one cycle may be need in order to allow time for data outputs to stop driving and new address to be driven (bus turn around time). During a write access, the address/data bus direction is always in the input mode. July 30, 2012 S29VS_XS-R_00_08 S29VS/XS-R MirrorBit® Flash Family 17 Da t a Sh e e t ( A d va n ce In for ma t i on ) The upper address is set to Zero or all Ones, for bottom or top boot respectively, during a Hardware Reset, operate in ADM mode during the early phase of boot code execution where only a single address cycle would be issued with the lower 16 bit of the address reaching the memory in AADM mode. The default high order address bits will direct the early boot accesses to the 128 Kbytes at the boot end of the device. Note that in AADM interface mode this effectively requires that one of the boot sectors is selected for any address overlay mode because in the initial phase of AADM mode operation the host memory controller may only issue the low order address thus limiting the early boot time address space to the 128 Kbytes at the boot end of the device. 6.3.3 Default Access Mode Upon power-up or hardware reset, the device defaults to the Asynchronous Access mode. 6.4 Bus Operations Table 6.6 describes the required state of each input signal for each bus operation. Table 6.6 Device Bus Operations Operation CE# OE# WE# Standby (CE# deselect) H X X Hardware Reset X X X CLK AVD# A28-A16 A/DQ 15-A/DQ0 RESET# X X X High-Z H X X X High-Z L Standby & Reset Asynchronous Mode Operations Asynchronous Address Latch L H X X Addr In Addr In H L L H X X Addr In H L H X X X Addr In H Asynchronous Read L L H X H X Data Output Valid H Asynchronous Write Latched Data L H X H X Data Input Valid H (S29VS256R and S29VS128R) Asynchronous Upper Address Latch (S29XS256R and S29XS128R Only) Asynchronous Lower Address Latch (S29XS256R and S29XS128R Only) Synchronous Mode Operations Latch Starting Burst Address by CLK - ADM mode Latch Upper Starting Burst Address by CLK (S29XS256R and S29XS128R Only) Latch Lower Starting Burst Address by CLK (S29XS256R and S29XS128R Only) Burst Read and advance to next address (1) L H H L Addr In Addr In H L L H L X Addr In H L H H L X Addr In H L L H H X Data Output Valid H X X X X High-Z H Terminate current Burst cycle Legend: L = Logic 0, H = Logic 1, X = can be either VIL or VIH. X = rising edge. Note: 1. Data is delivered by a read operation only after the burst initial wait state count has been satisfied. 18 S29VS/XS-R MirrorBit® Flash Family S29VS_XS-R_00_08 July 30, 2012 Dat a 6.5 S he e t ( Ad van ce I nfor m at i on ) Device ID and CFI (ID-CFI) There are two traditional methods for systems to identify the type of Flash memory installed in the system. One has been traditionally been called Autoselect and is now referred to as Device Identification (ID). A command is used to enable an address space overlay where up to 16 word locations can be read to get JEDEC manufacturer identification (ID), device ID, and some configuration and protection status information from the Flash memory. The system can use the manufacturer and device IDs to select the appropriate driver software to use with the Flash device. The other method is called Common Flash Interface (CFI). It also uses a command to enable an address space overlay where an extendable table of standard information about how the Flash memory is organized and behaves can be read. With this method the driver software does not have to be written with the specifics of each possible memory device in mind. Instead the driver software is written in a more general way to handle many different devices but adjusts the driver behavior based on the information in the CFI table stored in the Flash memory. Traditionally these two address spaces have used separate commands and were separate overlays. However, the mapping of these two address spaces are non-overlapping and so can be combined in to a single address space and appear together in a single overlay. Either of the traditional commands used to access (enter) the Autoselect (ID) or CFI overlay will cause the now combined ID-CFI address map to appear. A write at any sector address, in bank zero, having the least significant byte address value of AAh, with xx98h or xx90h data, switches the addressed sector to an overlay of the ID-CFI address map. These are called IDCFI Enter commands and are only valid when written to the specified bank when it is in read mode. The IDCFI address map appears within, and replaces Flash Array data of, the selected sector address range. The ID-CFI enter commands use the same address and data values used on previous generation memories to access the JEDEC Manufacturer ID (Autoselect) and Common Flash Interface (CFI) information, respectively. While the ID-CFI address space is overlaid, any write with xxF0h data to the device will remove the overlay and return the selected sector to showing Flash memory array data. Thus, the ID-CFI address space and commands are backward compatible with standard memory discovery algorithms. Within the ID-CFI address map there are two subsections: Table 6.7 ID-CFI Address Map Overview Byte Address Description Size Allocated (Bytes) Read/Write (SA) + 00000h to 0001Fh JEDEC ID (traditional Autoselect values) 32 Read Only (SA) + 00020h to CEh h CFI data structure 174 Read Only For the complete address map see Tables in Section 11.2, Device ID and Common Flash Memory Interface Address Map on page 58. 6.5.1 JEDEC Device ID The Joint Electron Device Engineering Council (JEDEC) standard JEP106T defines a method for reading the manufacturer ID and device ID of a compliant memory. This information is primarily intended for programming equipment to automatically match a device with the corresponding programming algorithm. The JEDEC ID information is structured to work with any memory data bus width e.g. x8, x16, x32. The code values are always byte wide but are located at bus width address boundaries such that incrementing the device address inputs will read successive byte, word, or double word locations with the codes always located in the least significant byte location of the data bus. Because the data bus is word wide each code byte is located in the lower half of each word location and the high order byte is always zero. July 30, 2012 S29VS_XS-R_00_08 S29VS/XS-R MirrorBit® Flash Family 19 Da t a 6.5.2 Sh e e t ( A d va n ce In for ma t i on ) Common Flash Memory Interface The Common Flash Interface (CFI) specification defines a standardized data structure that may be read from a flash memory device, which allows vendor-specified software algorithms to be used for entire families of devices. The data structure contains information for system configuration such as various electrical and timing parameters, and special functions supported by the device. Software support can then be deviceindependent, JEDEC ID-independent, and forward-and-backward-compatible for the specified flash device families. The system can read CFI information at the addresses within the selected sector as shown in Section 11.2, Device ID and Common Flash Memory Interface Address Map on page 58. Like the JEDEC Device ID information, CFI information is structured to work with any memory data bus width e.g. x8, x16, x32. The code values are always byte wide but are located at data bus width address boundaries such that incrementing the device address reads successive byte, word, or double word locations with the codes always located in the least significant byte location of the data bus. Because the data bus is word wide each code byte is located in the lower half of each word location and the high order byte is always zero. For further information, please refer to the Spansion CFI Version 1.4 (or later) Specification and the Spansion CFI Publication 100 (see also JEDEC publications JEP137-A and JESD68.01). Please contact JEDEC (http://www.jedec.org) for their standards and the Spansion CFI Publications may be found at the Spansion Web site (http://www.spansion.com/Support/AppNotes/CFI_v1.4_VendorSpec_Ext_A1.pdf at the time of this document’s publication). 6.5.3 Secured Silicon Region The Secured Silicon region provides an extra Flash memory area that can be programmed once and permanently protected from further changes. The Secured Silicon Region is 512 bytes in length. It consists of 256 bytes for factory data and 256 bytes for customer-secured data. The Secured Silicon Region (SSR) is overlaid in the sector address specified by the SSR enter command. Table 6.8 Secured Silicon Region Byte Address Range 6.5.4 Secure Silicon Region Size (SA) + 0000h to 00FFh Factory 256 Bytes (SA) + 0100h to 01FFh Customer 256 Bytes Configuration Register The Configuration Register Enter command is only valid when written to a bank that is in Read mode. The configuration register mode address map appears within, and replaces Flash Array data of, the selected sector address range. The meaning of the configuration register bits is defined in the configuration register operation description. In configuration register mode, a write of 00F0h to any address will return the sector to Read mode. 20 S29VS/XS-R MirrorBit® Flash Family S29VS_XS-R_00_08 July 30, 2012 Dat a 7. S he e t ( Ad van ce I nfor m at i on ) Device Operations This section describes the read and write bus operations, program, erase, simultaneous read/write, handshaking, and reset features of the Flash devices. The address space of the Flash Memory Array is divided into banks. There are three operation modes for each bank:  Read Mode  Embedded Algorithm (EA) Mode  Address Space Overlay (ASO) Mode Each bank of the device can be in any operation mode but, only one bank can be in EA or ASO mode at any one time. In Read Mode a Flash Memory Array bank may be read by simply selecting the memory, supplying the address, and taking read data when it is ready. This is done by asynchronous or burst accesses from the host system bus. The CU puts all banks in Read mode during Power-on, a Hardware Reset, after a Command Reset, or after a bank is returned to Read mode from EA mode. During a burst read access valid read data is indicated by the RDY signal being High. When RDY is Low burst read data is not valid and wait states must be added. The use of the RDY signal to indicate when valid data is transferred on the system data bus is called handshaking or flow control. EA and ASO modes are initiated by writing specific address and data patterns into command registers (see Table 11.1 on page 56). The command registers do not occupy any memory locations; they are loaded by write bus cycles with the address and data information needed to execute a command. The contents of the registers serve as input to the Control Unit (CU) and the CU dictates the function of the device. Writing incorrect address and data values or writing them in an improper sequence may place the device in an unknown state, in which case the system must write the reset command to return all banks to Read mode. The Flash memory array data in a bank that is in EA mode, is stable but undefined, and effectively unavailable for read access from the host system. While in EA mode the bank is used by the CU in the execution of commands. Typical command operations are programming or erasing of data in the Flash array. All other banks are available for read access while the one bank is in EA mode. This ability to read from one bank while another bank is used in the execution of a command is called Simultaneous Read and Write (SRW) and allows for continued operation of the system via the reading of data or code from other banks while one bank is programming or erasing data as a relatively long time frame background task. Only a status register read command can be used in a bank in EA mode to retrieve the EA status. While any one of the overlay address spaces are overlaid in a bank (entered) that bank is in ASO mode and no other bank may be in EA or ASO mode. All EA activity must be completed or suspended before entering any ASO mode. A command for entering an EA or ASO mode while another bank is in EA or ASO mode will be ignored. While an ASO mode is active (entered) in a bank, a read for Flash array data to any other bank is allowed. ASO mode selects a specific sector for the overlaid address space. Other sectors in the ASO bank still provide Flash array data and may be read during ASO mode. While SSR Lock, SSR, or Configuration Register is overlaid only the SSR Lock, SSR, or Configuration Register respectively may be programmed in the overlaid sector. While any of these ASO areas are being programmed the ASO bank switches to EA mode. The ID/CFI and factory portion of the SSR ASO is not customer programmable. An attempt to program in these areas will fail. July 30, 2012 S29VS_XS-R_00_08 S29VS/XS-R MirrorBit® Flash Family 21 Da t a 7.1 Sh e e t ( A d va n ce In for ma t i on ) Asynchronous Read The device defaults to reading array data asynchronously after device power-up or hardware reset. The device is in the Asynchronous mode when Bit 15 of the Configuration register is set to '1'. To read data from the memory array, the system must first assert CE# and AVD# to VIL with WE# at VIH and a valid address. Address access time (tACC) is equal to the delay from stable addresses to valid output data. The chip enable access time (tCE) is the delay from stable CE# to valid data at the outputs. See 10.9.2, AC Characteristics– Asynchronous Read on page 49. Any input on CLK is ignored while in Asynchronous mode. 7.1.1 S29VS-R ADM Access With CE# at VIL, WE# at VIH, and OE# at VIH, the system presents the address to the device and drives AVD# to VIL. AVD# is kept at VIL for at least tAVDP ns. The address is latched on the rising edge of AVD#. 7.1.2 S29XS-R AADM Access With CE# at VIL, WE# at VIH, and OE# at VIL, the system presents the upper address bits to DQ and drives AVD# to VIL. The upper address bits are latched when AVD# transitions to VIH. The system then drives AVD# to VIL again, with OE# at VIH and the lower address bits on the DQ signals. The lower address bits are latched on the next rising edge of AVD#. 7.2 Synchronous (Burst) Read Mode and Configuration Register The device is capable of continuous sequential burst operation and linear burst operation of a preset length. In order to use Synchronous (Burst) Read Mode the configuration register bit 15 must be set to 0. Prior to entering burst mode, the system should determine how many wait states are needed for the initial word of each burst access (see table below), what mode of burst operation is desired, how the RDY signal transitions with valid data, and output drive strength. The system would then write the configuration register command sequence. See Configuration Register on page 26 for further details. When the appropriate number of Wait States have occurred, data is output after the rising edge of the CLK. Subsequent words are output tBACC after the rising edge of each successive clock cycle, which automatically increments the internal address counter. RDY indicates the initial latency and any subsequent waits. 7.2.1 S29VS-R ADM Access To burst read data from the memory array in ADM mode, the system must assert CE# to VIL, and provide a valid address while driving AVD# to VIL for one cycle. OE# must remain at VIH during the one cycle that AVD# is at VIL. The data appears on A/DQ15 -A/DQ0 when CE# remains at VIL, after OE# is driven to VIL and the synchronous access times are satisfied. The next data in the burst sequence is read on each clock cycle that OE# and CE# remain at VIL. OE# does not terminate a burst access if it rises to VIH during a burst access. The outputs will go to high impedance but the burst access will continue until terminated by CE# going to VIH, or AVD# returns to VIL with a new address to initiate a another burst access. 7.2.2 S29XS-R AADM Access To burst read data from the memory array in AADM mode, the system must assert CE# to VIL, OE# must be driven to VIL with AVD# for one cycle while the upper address is valid. The rising edge of CLK when OE# and AVD# are at VIL captures the upper 16 bits of address. The rising edge of CLK when OE# is at VIH and AVD# is at VIL latches the lower 16 bits of address. The data appears on A/DQ15 -A/DQ0 when CE# remains at VIL, after OE# is driven to VIL and the synchronous access times are satisfied. The next data in the burst sequence is read on each clock cycle that OE# and CE# remain at VIL. Once OE# returns to VIH during a burst read the OE# no longer enables the outputs until after AVD# is at VIL with OE# at VIH - which signals that address-low has been captured for the next burst access. This is so that OE# at VIL may be used in conjunction with AVD# at VIL to indicate address-high on the A/DQ signals without enabling the A/DQ outputs, thus avoiding data output contention with Address-high. 22 S29VS/XS-R MirrorBit® Flash Family S29VS_XS-R_00_08 July 30, 2012 Dat a S he e t ( Ad van ce I nfor m at i on ) The device has a fixed internal address boundary that occurs every 256 Bytes (128 words). A boundary crossing latency of one or two additional wait states may be required. The device also reads data in 16 byte (8 word) aligned and length groups. When the initial address is not aligned at the beginning of a 16 byte boundary, additional wait states may be needed when crossing the first 16 byte boundary. The number of additional wait states depends on the clock frequency and starting address location. The following Tables show the latency for initial and boundary crossing wait state operation (note that ws = wait state). Table 7.1 Initial Wait State vs. Frequency Wait State Frequency (Maximum MHz) 3 27 4 40 5 54 6 66 7 80 8 95 9 104 10 120 Note: The default initial wait state delay after power on or reset is 13 wait states. Table 7.2 Address Latency for 10 -13 Wait States Word Initial Wait Subsequent Clock Cycles After Initial Wait States 0 D0 D1 D2 D3 D4 D5 D6 D7 +2 ws (1) D8 1 D1 D2 D3 D4 D5 D6 D7 1 ws +2 ws D8 2 D2 D3 D4 D5 D6 D7 1 ws 1 ws +2 ws D8 3 D3 D4 D5 D6 D7 1 ws 1 ws 1 ws +2 ws D8 4 D4 D5 D6 D7 1 ws 1 ws 1 ws 1 ws +2 ws D8 5 D5 D6 D7 1 ws 1 ws 1 ws 1 ws 1 ws +2 ws D8 6 D6 D7 1 ws 1 ws 1 ws 1 ws 1 ws 1 ws +2 ws D8 7 D7 1 ws 1 ws 1 ws 1 ws 1 ws 1 ws 1 ws +2 ws D8 10 -13 wait states Note: 1. This column applies to the 256 Byte boundary only. Table 7.3 Address Latency for 9 Wait States Word Initial Wait Subsequent Clock Cycles After Initial Wait States 0 D0 D1 D2 D3 D4 D5 D6 D7 +1 ws (1) D8 1 D1 D2 D3 D4 D5 2 D2 D3 D4 D5 D6 D6 D7 1 ws +1 ws D8 D7 1 ws 1 ws +1 ws 3 D3 D4 D5 D6 D8 D7 1 ws 1 ws 1 ws +1 ws D8 4 D4 D5 D6 D7 1 ws 1 ws 1 ws 1 ws +1 ws D8 5 D5 D6 6 D6 D7 D7 1 ws 1 ws 1 ws 1 ws 1 ws +1 ws D8 1 ws 1 ws 1 ws 1 ws 1 ws 1 ws +1 ws 7 D7 1 ws 1 ws D8 1 ws 1 ws 1 ws 1 ws 1 ws +1 ws D8 9 wait states Note: 1. This column applies to the 256 Byte boundary only. July 30, 2012 S29VS_XS-R_00_08 S29VS/XS-R MirrorBit® Flash Family 23 Da t a Sh e e t ( A d va n ce In for ma t i on ) Table 7.4 Address Latency for 8 Wait States Word Initial Wait Subsequent Clock Cycles After Initial Wait States 0 D0 D1 D2 D3 D4 D5 D6 D7 1 D1 D2 D3 D4 D5 D6 D7 1 ws D8 2 D2 D3 D4 D5 D6 D7 1 ws 1 ws D8 D3 D4 D5 D6 D7 1 ws 1 ws 1 ws D8 3 D8 8 wait states 4 D4 D5 D6 D7 1 ws 1 ws 1 ws 1 ws D8 5 D5 D6 D7 1 ws 1 ws 1 ws 1 ws 1 ws D8 6 D6 D7 1 ws 1 ws 1 ws 1 ws 1 ws 1 ws D8 7 D7 1 ws 1 ws 1 ws 1 ws 1 ws 1 ws 1 ws D8 D7 D8 D9 Table 7.5 Address Latency for 7 Wait States Word Initial Wait Subsequent Clock Cycles After Initial Wait States 0 D0 D1 D2 D3 D4 D5 D6 1 D1 D2 D3 D4 D5 D6 D7 D8 2 D2 D3 D4 D5 D6 D7 1 ws D8 D9 3 D3 D4 D5 D6 D7 1 ws 1 ws D8 D9 4 D4 D5 D6 D7 1 ws 1 ws 1 ws D8 D9 5 D5 D6 D7 1 ws 1 ws 1 ws 1 ws D8 D9 6 D6 D7 1 ws 1 ws 1 ws 1 ws 1 ws D8 D9 7 D7 1 ws 1 ws 1 ws 1 ws 1 ws 1 ws D8 D9 7 wait states Table 7.6 Address Latency for 6 Wait States Word Initial Wait Subsequent Clock Cycles After Initial Wait States 0 D0 D1 D2 D3 D4 D5 D6 D7 D8 1 D1 D2 D3 D4 D5 D6 D7 D8 D9 2 D2 D3 D4 D5 D6 D7 D8 D9 D10 3 D3 D4 D5 D6 D7 1 ws D8 D9 D10 6 wait states 4 D4 D5 D6 D7 1 ws 1 ws D8 D9 D10 5 D5 D6 D7 1 ws 1 ws 1 ws D8 D9 D10 6 D6 D7 1 ws 1 ws 1 ws 1 ws D8 D9 D10 7 D7 1 ws 1 ws 1 ws 1 ws 1 ws D8 D9 D10 Table 7.7 Address Latency for 5 Wait States Word Initial Wait Subsequent Clock Cycles After Initial Wait States 0 D0 D1 D2 D3 D4 D5 D6 D7 D8 1 D1 D2 D3 D4 D5 D6 D7 D8 D9 2 D2 D3 D4 D5 D6 D7 D8 D9 D10 3 D3 D4 D5 D6 D7 D8 D9 D10 D11 4 D4 D5 D6 D7 1 ws D8 D9 D10 D11 5 D5 D6 D7 1 ws 1 ws D8 D9 D10 D11 5 wait states 24 6 D6 D7 1 ws 1 ws 1 ws D8 D9 D10 D11 7 D7 1 ws 1 ws 1 ws 1 ws D8 D9 D10 D11 S29VS/XS-R MirrorBit® Flash Family S29VS_XS-R_00_08 July 30, 2012 Dat a S he e t ( Ad van ce I nfor m at i on ) Table 7.8 Address Latency for 4 Wait States Word Initial Wait Subsequent Clock Cycles After Initial Wait States 0 D0 D1 D2 D3 D4 D5 D6 D7 1 D1 D2 D3 D4 D5 D6 D7 D8 D9 2 D2 D3 D4 D5 D6 D7 D8 D9 D10 D3 D4 D5 D6 D7 D8 D9 D10 D11 4 D4 D5 D6 D7 D8 D9 D10 D11 D12 5 D5 D6 D7 1 ws D8 D9 D10 D11 D12 3 D8 4 wait states 6 D6 D7 1 ws 1 ws D8 D9 D10 D11 D12 7 D7 1 ws 1 ws 1 ws D8 D9 D10 D11 D12 D8 Table 7.9 Address Latency for 3 Wait States Word Initial Wait Subsequent Clock Cycles After Initial Wait States 0 D0 D1 D2 D3 D4 D5 D6 D7 1 D1 D2 D3 D4 D5 D6 D7 D8 D9 2 D2 D3 D4 D5 D6 D7 D8 D9 D10 3 D3 D4 D5 D6 D7 D8 D9 D10 D11 4 D4 D5 D6 D7 D8 D9 D10 D11 D12 5 D5 D6 D7 D8 D9 D10 D11 D12 D13 6 D6 D7 1 ws D8 D9 D10 D11 D12 D13 7 D7 1 ws 1 ws D8 D9 D10 D11 D12 D13 3 wait states 7.2.3 Continuous Burst The device continues to output sequential burst data from the memory array, wrapping around to address 0000000h after it reaches the highest addressable memory location, until the system drives CE# high, RESET# low, or AVD# low in conjunction with a new address. See Table 6.6, Device Bus Operations on page 18. If the host system crosses a bank boundary while reading in burst mode, and the subsequent bank is not programming or erasing, an address boundary crossing latency might be required. If the host system crosses the bank boundary while the subsequent bank is programming or erasing, continuous burst halts (RDY will be disabled and data will continue to be driven). 7.2.4 8-, 16-Word Linear Burst with Wrap Around Table 7.10 Burst Address Groups Mode Group Size Group Byte Address Ranges 8-word 16 bytes 0-Fh, 10-1Fh, 20-2Fh,... 16-word 32 bytes 0-1Fh, 20-3Fh, 30-4Fh,... The remaining two modes are fixed length linear burst with wrap around, in which a fixed number of words are read from consecutive addresses. In each of these modes, the burst addresses read are determined by the group within which the starting address falls. The groups are sized according to the number of words read in a single burst sequence for a given mode (see Table 7.10). As an example: if the starting address in the 8-word mode is system byte address 3Ch, the address range to be read would be byte address 30-3Fh, and the burst sequence would be 3C-3E-30-32-34-36-38-3Ah. The burst sequence begins with the starting address written to the device, wraps back to the first address in the selected group, and outputs a maximum of 8 words. No additional wait states will be required within the 8word burst. The 8th word will continue to be driven until the burst operation is aborted (CE# goes to VIH, a new address is latched in for a new burst operation, or a hardware reset). In a similar fashion, the 16-word Linear Wrap modes begin their burst sequence on the starting address written to the device, and then wrap back to the first address in the selected address group. Additional wait states could be added the first time the July 30, 2012 S29VS_XS-R_00_08 S29VS/XS-R MirrorBit® Flash Family 25 Da t a Sh e e t ( A d va n ce In for ma t i on ) device crosses from one to the other group of 8 words in a 16-word burst. The number will depend on the starting address and the wait state set within the configuration register. See Table 7.3 on Page 21 to Table 7.9 on page 25. Note that in these two burst read modes the address pointer does not cross the boundary that occurs every 128 words; thus, no 128-word address boundary crossing wait states are inserted for linear burst with wrap. Figure 7.1 Synchronous Read Load Initial Address Address = RA RA = Read Address Wait Programmable Wait State Setting CR0.14 - CR0.11 sets initial access time (from address latched to valid data) from 3 to 13 clock cycles Read Initial Data RD = DQ[15:0] RD = Read Data Wait X Clocks (if required): Additional Latency Due to Starting Address and Clock Frequency Read Next Data RD = DQ[15:0] No Yes Crossing Boundary? No End of Data? Yes Completed 7.2.5 Configuration Register Configuration register (CR) sets various operational parameters associated with burst mode. Upon power-up or hardware reset, the device defaults to the idle state, and the configuration register settings are in their default state. The host system should determine the proper settings for the configuration register, and then execute the Set Configuration Register command sequence, before attempting burst operations. The Configuration Register can also be read using a command sequence (see Table 11.1 on page 56). The table below describes the register settings and indicates the default state of each bit after power-on or a hardware reset. The configuration register bits are not affected by a command reset. 26 S29VS/XS-R MirrorBit® Flash Family S29VS_XS-R_00_08 July 30, 2012 Dat a S he e t ( Ad van ce I nfor m at i on ) Table 7.11 Configuration Register CR BIt Function CR.15 Device Read Mode CR.14 CR.13 CR.12 Programmable Read Wait States CR.11 CR.10 RDY Polarity CR.9 Reserved CR.8 RDY Timing CR.7 Output Drive Strength CR.6 Reserved CR.5 Reserved CR.4 Reserved CR.3 Reserved CR.2 CR.1 Burst Length CR.0 7.2.5.1 Settings (Binary) 0 = Synchronous Read Mode 1 = Asynchronous Read Mode (Default) 0000 = Reserved 0001 = 3rd Initial data is valid on the 0010 = 4th 0011 = 5th .. . rising CLK edge after addresses are latched .. . 1011 = 13th (Default) 1100 = Reserved 1101 = Reserved 1110 = Reserved 1111 = Reserved 0 = RDY signal is active low 1 = RDY signal is active high (Default) 0 = Reserved 1 = Reserved (Default) 0 = RDY active one clock cycle before data 1 = RDY active with data (Default) 0 = Full Drive= Current Driver Strength (Default) 1 = Half Drive 0 = Reserved 1 = Reserved (Default) 0 = Reserved (Default) 1 = Reserved 0 = Reserved (Default) 1 = Reserved 0 = Reserved 1 = Reserved (Default) 000 = Continuous (Default) 010 = 8-Word (16-Byte) Linear Burst with wrap around 011 = 16-Word (32-Byte) Linear Burst with wrap around (All other bit settings are reserved) Device Read Mode Configuration Register bit 15 (CR.15) controls whether read accesses via the bus interface are in asynchronous or burst mode. Asynchronous mode is the default after power-on or hardware reset. Write accesses are always conducted with asynchronous mode timing, independent of the read mode. 7.2.5.2 Wait States Configuration Register bits 14 to 11 (CR.[14..11]) define the number of delay cycles after the AVD# Low cycle that captures the initial address until the cycle that read data is valid. The bits from 14 to 11 are in most to least significant order. The random address access at the beginning of each read burst takes longer than the subsequent read cycles. The memory bus interface must be told how many cycles to wait before driving valid data then advancing to the next data word. The number of initial wait cycles will vary with the memory clock rate. The number of wait states is found in the wait state table information above. The minimum number of wait cycles is three. The maximum is 13. The default after power-on or hardware reset is 13 cycles. When the appropriate number of Wait States have occurred, data is output after the rising edge of the CLK. Subsequent words are output tBACC after the rising edge of each successive clock cycle, which automatically increments the internal address counter. 7.2.5.3 RDY Polarity Configuration Register bit 10 (CR.10) controls whether the RDY signal indicates valid data when High or when Low. When this bit is zero the RDY signal indicates data is valid when the signal is Low. When this bit is one the RDY signal indicates data is valid when the signal is High. The default for this bit is set to one after power-on or a hardware reset. July 30, 2012 S29VS_XS-R_00_08 S29VS/XS-R MirrorBit® Flash Family 27 Da t a 7.2.5.4 Sh e e t ( A d va n ce In for ma t i on ) RDY Timing Configuration Register bit 8 (CR.8) controls whether the RDY signal indicates valid data on the same cycle that data is valid or one cycle before data is valid. When this bit is zero the RDY signal indicates data is valid in the same cycle the data is valid. When this bit is one the RDY signal indicates data is valid one cycle before data is valid. The default for this bit is set to one after power-on or a hardware reset. 7.2.5.5 Output Drive Strength Configuration Register bit 7 (CR.7) controls whether the data outputs drive with full or half strength. When this bit is zero the data outputs drive with full strength. When this bit is one the data outputs drive with half strength. The default for this bit is cleared to zero after power-on or a hardware reset. 7.2.5.6 Burst Length Configuration Register bits 2 to 0 (CR.[2..0]) define the length of burst read accesses. The bits from 2 to 0 are in most to least significant order. See the register table for code meaning & default value. 7.3 Status Register The status of program and erase operations is provided by a status register. A status register read command is written followed by a read of the status register for each access of the status register information. The Clear Status Register Command will reset the status register. The status register can be read in synchronous or asynchronous mode. Table 7.12 Status Register Reset State Bit 7 Device Ready Bit. Overall status Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Erase Suspend Status Bit Erase Status Bit Program Status Bit RFU Program Suspend Status Bit Sector Lock Status Bit Bank Status Bit DRB ESSB ESB PSB RFU PSSB SLSB BSB 1 at Reset 0 at Reset 0 at Reset 0 at Reset 0 at Reset 0 at Reset 0 at Reset 0 at Reset Notes: 1. Status bits higher than Bit 7 are undefined. 2. Bit 7 reflects the device status. 3. If the device is busy, Bit 0 is used to check whether the addressed bank is busy or some other bank is busy. 4. All the other bits reflect the status of the device. Table 7.13 Status Register - Bit 7 Bit 7 Device Ready Bit. Overall status DRB Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Erase Suspend Status Bit Erase Status Bit Program Status Bit RFU Program Suspend Status Bit Sector Lock Status Bit Bank Status Bit ESSB ESB PSB RFU PSSB SLSB BSB Invalid Invalid Invalid Invalid Invalid Invalid VALID VALID VALID VALID VALID VALID VALID VALID 0 Device busy programming or erasing 1 Device ready Notes: 1. Bit 7 is set when there is no erase or program operation in progress in the device. 2. Bits 1 through 6 are valid if and only if Bit 7 is set. 28 S29VS/XS-R MirrorBit® Flash Family S29VS_XS-R_00_08 July 30, 2012 Dat a S he e t ( Ad van ce I nfor m at i on ) Table 7.14 Status Register - Bit 6 Bit 7 Device Ready Bit. Overall status DRB 1 Bits 6:1 only valid when Bit 7=1 1 Bit 6:1 only valid when Bit 7=1 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Erase Suspend Status Bit Erase Status Bit Program Status Bit RFU Program Suspend Status Bit Sector Lock Status Bit Bank Status Bit ESSB ESB PSB RFU PSSB SLSB BSB X X X X X X X X X X X X 0 No Erase in Suspension 1 Erase in Suspension Notes: 1. Upon issuing the “Erase Suspend” Command, the user must continue to read status until DRB becomes 1 before accessing another sector within the same bank. 2. Cleared by “Erase Resume” Command. Table 7.15 Status Register - Bit 5 Bit 7 Device Ready Bit. Overall status DRB Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Erase Suspend Status Bit Erase Status Bit Program Status Bit RFU Program Suspend Status Bit Sector Lock Status Bit Bank Status Bit ESSB ESB PSB RFU PSSB SLSB BSB X Erase successful X X X X X X X X X X 1 Bits 6:1 only valid when Bit 7=1 0 1 Bit 6:1 only valid when Bit 7=1 X 1 Erase error Notes: 1. ESB bit reflects “success” or “failure” of the most recent erase operation. 2. Cleared by “Clear Status Register” Command as well as by hardware reset. Table 7.16 Status Register - Bit 4 Bit 7 Device Ready Bit. Overall status DRB Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Erase Suspend Status Bit Erase Status Bit Program Status Bit RFU Program Suspend Status Bit Sector Lock Status Bit Bank Status Bit ESSB ESB PSB RFU PSSB SLSB BSB X X Program successful X X X X X X X X X X 1 Bits 6:1 only valid when Bit 7=1 0 1 Bit 6:1 only valid when Bit 7=1 1 Program fail Notes: 1. PSB bit reflects “success” or “failure” of the most recent program operation. 2. Cleared by “Clear Status Register” Command as well as by hardware reset. July 30, 2012 S29VS_XS-R_00_08 S29VS/XS-R MirrorBit® Flash Family 29 Da t a Sh e e t ( A d va n ce In for ma t i on ) Table 7.17 Status Register - Bit 3 Bit 7 Device Ready Bit. Overall status DRB Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Erase Suspend Status Bit Erase Status Bit Program Status Bit RFU Program Suspend Status Bit Sector Lock Status Bit Bank Status Bit ESSB ESB PSB RFU PSSB SLSB BSB X X X X X X X 1 Bits 6:1 only valid when Bit 7=1 Notes: 1. This Register is reserved for future use. 2. Cleared by “Clear Status Register” Command as well as by hardware reset. Table 7.18 Status Register - Bit 2 Bit 7 Device Ready Bit. Overall status DRB Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Erase Suspend Status Bit Erase Status Bit Program Status Bit RFU Program Suspend Status Bit Sector Lock Status Bit Bank Status Bit ESSB ESB PSB RFU PSSB SLSB BSB X X X X No Program in suspension X X X X X X Program in suspension X X 1 Bits 6:1 only valid when Bit 7=1 0 1 Bit 6:1 only valid when Bit 7=1 1 Notes: 1. Upon issuing the “Program Suspend” Command, the user must continue to read status until DRB becomes 1 before accessing another sector within the same bank. 2. Cleared by “Program Resume” Command. Table 7.19 Status Register - Bit 1 Bit 7 Device Ready Bit. Overall status DRB Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Sector Lock Status Bit Bank Status Bit BSB Erase Suspend Status Bit Erase Status Bit Program Status Bit RFU Program Suspend Status Bit ESSB ESB PSB RFU PSSB SLSB X X X X X Sector not locked during operation X X X X X Sector locked error 0 1 Bits 6:1 only valid when Bit 7=1 1 Bit 6:1 only valid when Bit 7=1 X 1 X Notes: 1. SLSB indicates that a program or erase operation failed to program or erase because the sector was locked or the operation was attempted on the protected Secure Silicon Region. 2. SLSB reflects the status of the most recent program or erase operation. 3. SLSB is cleared by “Clear Status Register” or by hardware reset. 30 S29VS/XS-R MirrorBit® Flash Family S29VS_XS-R_00_08 July 30, 2012 Dat a S he e t ( Ad van ce I nfor m at i on ) Table 7.20 Status Register - Bit 0 Bit 7 Device Ready Bit. Overall status DRB Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Erase Suspend Status Bit Erase Status Bit Program Status Bit RFU Program Suspend Status Bit Sector Lock Status Bit Bank Status Bit ESSB ESB PSB RFU PSSB SLSB BSB 0 0 Bits 6:1 only valid when Bit 7=1 Program or Erase op. in addressed Bank X X X X X X X X X X X X Program or Erase op. in other Bank 1 0 Bit 6:1 only valid when Bit 7=1 No active Program or Erase op. 0 Bits 6:1 only valid when Bit 7=1 1 X X X X X X X X X X X X 1 Bit 6:1 only valid when Bit 7=1 1 invalid Note: 1. BSB is used to check if a program or erase operation in progress in the current bank. 7.4 Blank Check The Blank Check command will confirm if the selected sector is erased. The Blank Check command does not allow for reads to the array during the Blank Check. Reads to the array while this command is executing will return unknown data.  Blank Check is only functional in Asynchronous Read mode (Configuration Register - CR [15] = 1).  To initiate a Blank Check on Sector X, write 33h to address 555h in Sector X. while the device is in the Idle state (not during program suspend, not during erase suspend, ...).  The Blank Check command may not be written while the device is actively programming or erasing. Blank Check does not support simultaneous operations.  Use the Status Register read to confirm if the device is still busy and when compete if the sector is blank or not.  Bit 5 of the Status Register will be cleared to zero if the sector is erased and set to one if not erased.  Bit 7 & Bit 0 of the Status Register will show if the device is performing a Blank Check (similar to an erase operation).  As soon as any bit is found to not be erased, the device will halt the operation and report the results.  Once the Blank Check is completed, the device will to return to the Idle State. 7.5 Simultaneous Read/Write The simultaneous read/write feature allows the host system to read data from one bank of memory while programming or erasing another bank of memory. An erase operation may also be suspended to read from or program another location within the same bank (note: programming to the sector being erased is not allowed). Figure 10.14, Back-to-Back Read/Write Cycle Timings - ADM Interface on page 54 shows how read and write cycles may be initiated for simultaneous operation with zero latency. Refer to the DC Characteristics on page 45 table for read-while-program and read-while-erase current specification. July 30, 2012 S29VS_XS-R_00_08 S29VS/XS-R MirrorBit® Flash Family 31 Da t a 7.6 Sh e e t ( A d va n ce In for ma t i on ) Writing Commands/Command Sequences The device accepts Asynchronous write bus operations. During an asynchronous write bus operation, the system must drive CE# and WE# to VIL and OE# to VIH when providing an address and data. While an address is valid, AVD# must be driven to VIL. Addresses are latched on the rising edge of AVD#, data is latched on the rising edge of WE#. All writes to the memory are single word length and follow asynchronous timing. However, it is allowed to leave the host and memory interfaces in synchronous mode as long as the host synchronous timing for a single word synchronous write can meet the timing requirements of the memory device write cycle. Generally a synchronous write would include Clock toggling during the write but, it is also allowed for Clock to be at VIL during the write. If the device is in the Synchronous Read Mode (CR.15 = 0), the addresses are latched on the rising edge of CLK when AVD# is at VIL, while data is latched on the rising edge of WE#. If CLK is held at VIL, addresses are latched on the rising edge of AVD#. CLK should not be held at VIH when writing commands while the device is in Synchronous Read Mode. See the Table 6.6, Device Bus Operations on page 18 for the signal combinations that define each phase of a write bus operation to the device. Each write is a command or part of a command sequence to the device. The address provided in each write operation may be a bit pattern used to help identify the write as a command to the device. The upper portion of the address may also select the bank or sector in which the command operation is to be performed. A Bank Address (BA) is the set of address bits required to uniquely select a bank. Similarly, a Sector Address (SA) is the address bits required to uniquely select a sector. The data in each write identifies the command operation to be performed or supplies information needed to perform the operation. See Table 11.1, Command Definitions on page 56 for a listing of the commands accepted by the device. ICC2 in DC Characteristics on page 45 represents the active current specification for an Embedded Algorithm operation. 7.7 Program/Erase Operations  When the Embedded Program algorithm is complete, the device returns to the calling routing (Erase Suspend, SSR Lock, Secure Silicon Region, or Idle State).  The system can determine the status of the program operation by reading the Status Register. Refer to Status Register on page 28 for information on these status bits.  A 0 cannot be programmed back to a 1. A succeeding read shows that the data is still 0. Only erase operations can convert a 0 to a 1 . old data new data results 0011 0101 0001  Any commands written to the device during the Embedded Program Algorithm are ignored except the Program Suspend, and Status Read command. Any commands written to the device during the Embedded Erase Algorithm are ignored except Erase Suspend and Status Read command. Reading from a bank that is not programming or erasing is allowed.  A hardware reset immediately terminates the program/erase operation and the program command sequence should be reinitiated once the device has returned to the idle state, to ensure data integrity. 32 S29VS/XS-R MirrorBit® Flash Family S29VS_XS-R_00_08 July 30, 2012 Dat a 7.7.1 S he e t ( Ad van ce I nfor m at i on ) Write Buffer Programming Write Buffer Programming allows the system to write 1 to 64 bytes in one programming operation. The Write Buffer Programming command sequence is initiated by first writing the Write Buffer Load command written at the Sector Address + 555h in which programming occurs. Next, the system writes the number of word locations minus 1 at the Sector Address + 2AAh. This tells the device how many write buffer addresses are loaded with data and therefore when to expect the Program Buffer to Flash confirm command. The Sector Address must match during the Write Buffer Load command and during the Write Word Count command and the Sector must be unlocked or the operation will abort and return to the initiating state. The write buffer is used to program data within a 64 byte page aligned on a 64 byte boundary. Thus, a full page Write Buffer programming operation must be aligned on a page boundary. Programming operations of less than a full page may start on any word boundary but may not cross a page boundary. The system then writes the starting address/data combination. This starting address is the first address/data pair to be programmed, and selects the write-buffer-page address. The Sector address must match the Write Buffer Load Sector Address or the operation will abort and return to the initiating state. All subsequent address/data pairs must be in sequential order. All write buffer addresses must be within the same page. If the system attempts to load data outside this range, the operation aborts after the Write to Buffer command is executed and the device will indicate a Program Fail in the Status Register at bit location 4 (PSB). A “Clear Status Register” must be issued to clear the PSB status bit. The counter decrements for each data load operation. Once the specified number of write buffer locations have been loaded, the system must then write the Program Buffer to Flash command at the Sector Address + 555h. The device then goes busy. The Embedded Program algorithm automatically programs and verifies the data for the correct data pattern. The system is not required to provide any controls or timings during these operations. If the incorrect number of write buffer locations have been loaded and the Program Buffer to Flash command is issued, the Status Register will indicate a program fail at bit location 4 (PSB). A “Clear Status Register” must be issued to clear the PSB status bit. The write-buffer embedded programming operation can be suspended using the Program Suspend command. When the Embedded Program algorithm is complete, the device then returns to Erase Suspend, SSR Lock, Secure Silicon Region, or Idle state. The system can determine the status of the program operation by reading the Status Register. Refer to Status Register on page 28 for information on these status bits. The Write Buffer Programming Sequence can be Aborted in the following ways:  Load a value greater than the buffer size during the Number of Locations step.  Write an address that is outside the Page of the Starting Address during the write buffer data loading stage of the operation. The Write Buffer Programming Sequence can be stopped and reset by the following: Hardware Reset or Power cycle. July 30, 2012 S29VS_XS-R_00_08 S29VS/XS-R MirrorBit® Flash Family 33 Da t a Sh e e t ( A d va n ce In for ma t i on ) Software Functions and Sample Code Table 7.21 Write Buffer Program Cycle Description Operation Byte Address Word Address Data 1 Write Buffer Load Command Write Sector Address + AAAh Sector Address + 555h 0025h 2 Write Word Count Write Sector Address + 555h Sector Address + 2AA Word Count (N–1)h 3 to 34 Load Buffer Word N Write Last Write Buffer to Flash Write Number of words (N) loaded into the write buffer can be from 1 to 32 words. Program Address, Word N Sector Address + AAAh Word N Sector Address + 555h 0029h Notes: 1. Base = Base Address. 2. Last = Last cycle of write buffer program operation; depending on number of words written, the total number of cycles may be from 6 to 37. 3. For maximum efficiency, it is recommended that the write buffer be loaded with the highest number of words (N words) possible. The following is a C source code example of using the write buffer program function. Refer to the Spansion Low Level Driver User’s Guide (available on www.spansion.com) for general information on Spansion Flash memory software development guidelines. /* Example: Write Buffer Programming Command */ /* NOTES: Write buffer programming limited to 32 words. */ /* All addresses to be written to the flash in */ /* one operation must be within the same flash */ /* page. A flash page begins at addresses */ /* evenly divisible by 0x20. */ UINT16 *src = source_of_data; /* address of source data */ UINT16 *dst = destination_of_data; /* flash destination address */ UINT16 wc = words_to_program -1; /* word count (minus 1) */ *( (UINT16 *)sector_address + 0x555 ) = 0x0025; /* write write buffer load command */ *( (UINT16 *)sector_address + 0x2AA) = wc; /* write word count (minus 1) */ do{ *dst = *src; /* ALL dst MUST BE SAME PAGE */ /* write source data to destination */ dst++; /* increment destination pointer */ src++; /* increment source pointer */ wc--; /* decrement word count */ }while ( wc >= 0 ); /* do it again */ *( (UINT16 *)sector_address + 0x555) /* poll for completion */ 34 = 0x0029; /* write confirm command S29VS/XS-R MirrorBit® Flash Family */ S29VS_XS-R_00_08 July 30, 2012 Dat a 7.7.2 S he e t ( Ad van ce I nfor m at i on ) Program Suspend/Program Resume Commands The Program Suspend command allows the system to interrupt an embedded programming operation or a Write to Buffer programming operation so that data can read from any non-suspended sector. When the Program Suspend command is written during a programming process, the device halts the programming operation within tPSL (program suspend latency) and updates the status bits. Addresses are don't-cares when writing the Program Suspend command. After the programming operation has been suspended, the system can read array data from any nonsuspended sector and page. The Program Suspend command may also be issued during a programming operation while an erase is suspended. In this case, data may be read from any addresses not in Erase Suspend or Program Suspend. After the Program Resume command is written, the device reverts to programming and the status bits are updated. The system can determine the status of the program operation by reading the Status Register, just as in the standard program operation. See Status Register on page 28 for more information. The system must write the Program Resume command to exit the Program Suspend mode and continue the programming operation. Further writes of the Program Resume command are ignored. Another Program Suspend command can be written after the device has resumed programming. Software Functions and Sample Code Table 7.22 Program Suspend Cycle Operation Byte Address Word Address Data 1 Write Bank Address Bank Address 0051h The following is a C source code example of using the program suspend function. Refer to the Spansion Low Level Driver User’s Guide (available on www.spansion.com) for general information on Spansion Flash memory software development guidelines. /* Example: Program suspend command */ *( (UINT16 *)bank_addr + 0x000 ) = 0x0051; /* write suspend command */ Table 7.23 Program Resume Cycle Operation Byte Address Word Address Data 1 Write Sector Address + 000h Sector Address + 000h 0050h The following is a C source code example of using the program resume function. Refer to the Spansion Low Level Driver User’s Guide (available on www.spansion.com) for general information on Spansion Flash memory software development guidelines. /* Example: Program resume command */ *( (UINT16 *)sector_address + 0x000 ) = 0x0050; July 30, 2012 S29VS_XS-R_00_08 S29VS/XS-R MirrorBit® Flash Family /* write resume command */ 35 Da t a 7.7.3 Sh e e t ( A d va n ce In for ma t i on ) Sector Erase The sector erase function erases one sector in the memory array. (See Table 11.1 on page 56) The device does not require the system to preprogram prior to erase. The Embedded Erase algorithm automatically programs and verifies the entire memory for an all zero data pattern prior to electrical erase. After a successful sector erase, all locations within the erased sector contain FFFFh. The system is not required to provide any controls or timings during these operations. Sector Erase requires 2 commands. Each of the Sector Addresses must match, the lower addresses must be correct, and the sector must be unlocked previously by executing the Sector Unlock command and must not be locked by the Sector Lock Range command. When the Embedded Erase algorithm is complete, the bank returns to idle state and addresses are no longer latched. Note that while the Embedded Erase operation is in progress, the system can read data from the non-erasing banks. The system can determine the status of the erase operation by reading the Status Register. See Status Register on page 28 for information on these status bits. Once the sector erase operation has begun, only reading from outside the erase bank, read of Status Register, and the Erase Suspend command are valid. All other commands are ignored. However, note that a hardware reset immediately terminates the erase operation. If that occurs, the sector erase command sequence must be reinitiated once the device has returned to idle state, to ensure data integrity. See Program/Erase Operations on page 32 for parameters and timing diagrams. Software Functions and Sample Code Table 7.24 Sector Erase Cycle Description Operation Byte Address Word Address Data 1 Setup Command Write Sector Address + AAAh Sector Address + 555h 0080h 2 Sector Erase Command Write Sector Address + 555h Sector Address + 2AA 0030h The following is a C source code example of using the sector erase function. Refer to the Spansion Low Level Driver User’s Guide (available on www.spansion.com) for general information on Spansion Flash memory software development guidelines. /* Example: Sector Erase Command */ *( (UINT16 *)sector_address + 0x555 ) = 0x0080; *( (UINT16 *)sector_address + 0x2AA) 7.7.4 = 0x0030; /* write setup command /* write sector erase command */ */ Chip Erase The chip erase function erases the complete memory array. (See Table 11.1 on page 56). The device does not require the system to preprogram prior to erase. The Embedded Erase algorithm automatically programs and verifies the entire memory for an all zero data pattern prior to electrical erase. After a successful chip erase, all locations within the device contain FFFFh. The system is not required to provide any controls or timings during these operations. Chip Erase requires 2 commands. Each of the Sector Addresses must match, the lower addresses must be correct, and Sector 0 must be unlocked previously by executing the Sector Unlock command. If any sector has been locked by the Sector Lock Range command, the Chip Erase command will not start. When the Embedded Erase algorithm is complete, the device returns to idle state and addresses are no longer latched. Note that while the Embedded Erase operation is in progress, the system can not read data from the device. The system can determine the status of the erase operation by reading the Status Register. See Status Register on page 28 for information on these status bits. Once the chip erase operation has begun, only a Status Read, Hardware RESET or Power cycle are valid. All other commands are ignored. However, note that a Hardware Reset or Power Cycle immediately terminates the erase operation. If that occurs, the chip erase command sequence must be reinitiated once the device has returned to idle state, to ensure data integrity. See Program/Erase Operations on page 32 for parameters and timing diagrams. 36 S29VS/XS-R MirrorBit® Flash Family S29VS_XS-R_00_08 July 30, 2012 Dat a S he e t ( Ad van ce I nfor m at i on ) Software Functions and Sample Code Table 7.25 Chip Erase Cycle Description Operation Byte Address Word Address Data 1 Setup Command Write Base + AAAh Base + 555h 0080h 2 Chip Erase Command Write Base + 555h Base + 2AA 0010h The following is a C source code example of using the chip erase function. Refer to the Spansion Low Level Driver User’s Guide (available on www.spansion.com) for general information on Spansion Flash memory software development guidelines. /* Example: Chip Erase Command */ /* Note: Cannot be suspended 7.7.5 */ *( (UINT16 *)base_addr + 0x555 ) = 0x0080; /* write setup command */ *( (UINT16 *)base_addr + 0x2AA ) = 0x0010; /* write chip erase command */ Erase Suspend/Erase Resume Commands The Erase Suspend command allows the system to interrupt a sector erase operation and then read data from, or program data to, the device. This command is valid only during the sector erase operation. The Erase Suspend command is ignored if written during the chip erase operation. When the Erase Suspend command is written during the sector erase operation, the device requires a maximum of tESL (erase suspend latency) to suspend the erase operation and update the status bits. After the erase operation has been suspended, the bank enters the erase-suspend mode. The system can read data from or program data to the device. Reading at any address within erase-suspended sectors produces undetermined data. The system can read the Status Register to determine if a sector is actively erasing or is erase-suspended. Refer to Status Register on page 28 for information on these status bits. After an erase-suspended program operation is complete, the bank returns to the erase-suspend mode. The system can determine the status of the program operation by reading the Status Register, just as in the standard program operation. To resume the sector erase operation, the system must write the Erase Resume command. The device will revert to erasing and the status bits will be updated. Further writes of the Resume command are ignored. Another Erase Suspend command can be written after the chip has resumed erasing. July 30, 2012 S29VS_XS-R_00_08 S29VS/XS-R MirrorBit® Flash Family 37 Da t a Sh e e t ( A d va n ce In for ma t i on ) Software Functions and Sample Code Table 7.26 Erase Suspend Cycle Operation Byte Address Word Address Data 1 Write Bank Address Bank Address 00B0h The following is a C source code example of using the erase suspend function. Refer to the Spansion Low Level Driver User’s Guide (available on www.spansion.com) for general information on Spansion Flash memory software development guidelines. /* Example: Erase suspend command */ *( (UINT16 *)bank_addr + 0x000 ) = 0x00B0; /* write suspend command */ Table 7.27 Erase Resume Cycle Operation Byte Address Word Address Data 1 Write Sector Address + 000h Sector Address + 000h 0030h The following is a C source code example of using the erase resume function. Refer to the Spansion Low Level Driver User’s Guide (available on www.spansion.com) for general information on Spansion Flash memory software development guidelines. /* Example: Erase resume command */ *( (UINT16 *)sector_address + 0x000 ) = 0x0030; /* write resume command */ /* The flash needs adequate time in the resume state */ 7.7.6 Accelerated Program/Sector Erase Accelerated write buffer programming, and sector erase operations are enabled through the VPP function. This method is faster than the standard chip program and sector erase command sequences. The accelerated write buffer program and sector erase functions must not be used more than 50 times per sector. In addition, accelerated write buffer program and sector erase should be performed at room temperature (30°C ±10°C). If the system asserts VHH on VPP, the device automatically uses the higher voltage on the input to reduce the time required for program and erase operations. Removing VHH from the VPP input, upon completion of the embedded program or erase operation, returns the device to normal operation.  Simultaneous operations are not supported while VPP is at VHH. The VPP pin must not be at VHH for operations other than accelerated write buffer programming, accelerated sector erase, and status register read or device damage may result.  The VPP pin must not be left floating or unconnected; inconsistent behavior of the device may result.  There is a minimum of 100 ms required between accelerated write buffer programming and a subsequent accelerated sector erase. 7.8 Handshaking The handshaking feature allows the host system to detect when data is ready to be read by simply monitoring the RDY (Ready) pin, which is a dedicated output controlled by CE#. When CE# input is Low, the RDY output signal is actively driven. When both of the CE# inputs are High the RDY output is high-impedance. When CE# input and OE# input is Low, the A/DQ15-A/DQ0 output signals are actively driven. When both of the CE# inputs are High, or the OE# input is High, the A/DQ15-A/DQ0 outputs are high-impedance. When the device is operated in synchronous mode, and OE# is low (active), the initial word of burst data becomes available after the rising edge of the RDY. CR.8 in the Configuration Register allows the host to specify whether RDY is active at the same time that data is ready, or one cycle before data is ready (see Table 7.11 on page 27). When the device is operated in asynchronous mode, RDY will be high when CE# is low (active). 38 S29VS/XS-R MirrorBit® Flash Family S29VS_XS-R_00_08 July 30, 2012 Dat a 7.9 S he e t ( Ad van ce I nfor m at i on ) Hardware Reset The RESET# input provides a hardware method of resetting the device to idle state. When RESET# is driven low for at least a period of tRP, the device immediately terminates any operation in progress, tristates all outputs, resets the configuration register, and ignores all read/write commands for the duration of the reset operation. The device also resets the internal state machine to idle state. Hardware Reset clears the AADM upper address register to zero. To ensure data integrity the operation that was interrupted should be reinitiated once the device is ready to accept another command sequence. When RESET# is held at VSS, the device draws CMOS standby current (ICC4). If RESET# is held at VIL, but not at VSS, the standby current is greater. See Figure 10.10 for timing diagrams 7.10 Software Reset Software reset is part of the command set (see Table 11.1 on page 56) that also returns the device to idle state and must be used for the following conditions: 1. Exit ID/CFI mode 2. Exit Secure Silicon Region mode 3. Exit Configuration Register mode 4. Exit SSR Lock mode Reset commands are ignored once programming/erasure has begun until the operation is complete. Software Functions and Sample Code Table 7.28 Reset Cycle Operation Byte Address Word Address Data Reset Command Write Base + xxxh Base + xxxh 00F0h Note: Base = Base Address. The following is a C source code example of using the reset function. Refer to the Spansion Low Level Driver User’s Guide (available on www.spansion.com) for general information on Spansion Flash memory software development guidelines. /* Example: Reset (software reset of Flash state machine) */ *( (UINT16 *)base_addr + 0x000 ) = 0x00F0; 8. Sector Protection/Unprotection The Sector Protection/Unprotection feature disables or enables programming or erase operations in one or multiple sectors and can be implemented through software and/or hardware methods, which are independent of each other. This section describes the various methods of protecting data stored in the memory array. 8.1 Sector Lock/Unlock Command The Sector Lock/Unlock command sequence allows the system to protect all sectors from accidental writes or, unprotect one sector to allow programming or erasing of the sector. When the device is first powered up, all sectors are unlocked. To lock all sectors (enter protected mode), a Sector Lock/Unlock command must be issued to any Sector Address. Once this command is issued, only one sector at a time can be unlocked until power is cycled. To unlock a sector, the system must write the Sector Lock/Unlock command sequence. Two cycles are first written: addresses are x555h and x2AAh, and data is 60h. During the third cycle, the sector address (SLA) and unlock command (60h) are written, while specifying with address A6 whether that sector should be locked (A6 = VIL) or unlocked (A6 = VIH). A Program or Erase operation will check the unlocked Sector Address only at the beginning of the Program or Erase operation. It is not necessary to keep the sector being Programmed or Erased unlocked during the July 30, 2012 S29VS_XS-R_00_08 S29VS/XS-R MirrorBit® Flash Family 39 Da t a Sh e e t ( A d va n ce In for ma t i on ) operation. The system can change the unlocked Sector after programming or erasing the sector has begun. An Erase Resume or Program Resume command does not check the value of the unlocked Sector. If A6 is set to VIL,then all sectors in the array will be locked. Only one sector at a time can be unlocked. If a Sector Lock/Unlock command is issued to a sector that is protected by the Sector Lock Range command, all sectors in the part will be locked. 8.2 Sector Lock Range Command This command allows a range of sectors to be protected from program or erase (locked) until a hardware reset or power is removed from the device. Once this command is issued, all sectors are protected and the Sector Lock/Unlock command is ignored for the selected range of sectors. Sectors outside of the selected range must be unlocked one sector at a time using the Sector Unlock command in order to be erased/ programmed. Two cycles are first written: addresses are x555h and x2AAh, and data is 60h. During the third cycle, the sector address (SLA) and load sector address command (61h) is written. This cycle sets the lower sector address of the range. During the fourth cycle, the sector address (SLA) and load sector address command (61h) is written. This cycle sets the upper sector address of the range. The addresses reference a large sector address range (128 KB). If a sector address matches the location of the four small sectors, all of the small sectors will be protected as a group. The sectors selected by the lower and upper address, as well as all sectors between these sectors, are protected from program and erase until a hardware reset or power is removed. If the lower and upper sector addresses are for the same sector then only that one sector is locked. Flash address input A6 (system byte address bit a7) during both address cycles must be zero (A6 = VIL) for the addresses to be accepted as valid. If the first sector address cycle contains an address which is higher than the second sector address cycle, then the command sequence will be invalid. If A6 is set to one (A6 = VIH) on either address cycle, the command sequence will disable subsequent Sector Lock Range commands. A valid Sector Lock Range command sequence is accepted only once after a Hardware Reset or initial power up. Additional Sector Lock Range commands will be ignored. If a Sector Unlock command tries to unlock a Sector within the Sector Lock Range, the Sector will remain in locked state. Similarly, if a Sector that is currently unlocked by the Sector Unlock command is overlapped by a subsequent Sector Lock Range, that sector will be locked and program erase operations to that region will be ignored. This command is generally used by trusted boot code. After power on reset boot code has the option to check for any need to update sectors before locking them for the remainder of power on time. Once boot code is satisfied with the content of sectors to be protected the Sector Lock Range command is used to lock sectors against any program or erase during normal system operation. This adds an extra layer of protection for critical data that must be protected against accidental or malicious corruption. Yet, maintains flexibility for trusted boot code to perform occasional updates of the data. It is important to issue the Sector Lock Range command even if no sectors are to be protected so that sectors that should remain available for update cannot be later locked by accidental or malicious code behavior. 8.3 Hardware Data Protection Methods There are additional hardware methods by which intended or accidental erasure of any sectors can be prevented via hardware means. The following subsections describes these methods: 8.3.1 VPP Method Once VPP input is set to VIL, all program and erase functions are disabled and hence all Sectors (including the Secure Silicon Region) are protected. 8.3.2 Low VCC Write Inhibit When VCC is less than VLKO, the device does not accept any write cycles. This protects data during VCC power-up and power-down. 40 S29VS/XS-R MirrorBit® Flash Family S29VS_XS-R_00_08 July 30, 2012 Dat a S he e t ( Ad van ce I nfor m at i on ) The command register and all internal program/erase circuits are disabled. Subsequent writes are ignored until VCC is greater than VLKO. The system must provide the proper signals to the control inputs to prevent unintentional writes when VCC is greater than VLKO. 8.3.3 Write Pulse Glitch Protection Noise pulses of less than 3 ns (typical) on OE#, WE#, or CE# do not initiate a write cycle. 8.3.4 Power-Up Write Inhibit If CE# = RESET# = VIL and OE# = VIH during power up, the device does not accept write commands. The internal state machine is automatically reset to the idle state on power-up. 8.4 SSR Lock The SSR Lock consists of two bits. The Customer Secure Silicon Region Protection Bit is bit 0. The Factory Secure Silicon Region Protection Bit is bit 1. All other bits in this register return “1.” If the Customer Secure Silicon Region Protection Bit is set to “0,” the Customer Secure Silicon Region is protected and can not be programmed. If this bit is set to “1,” the Customer Secure Silicon Region is available for programming. Once this area has been programmed, the SSR Lock bit 0 should be programmed to “0.” 8.5 Secure Silicon Region The Secure Silicon Region provides an extra Flash memory region that may be programmed once and permanently protected from further programming or erase.  Reads can be performed in the Asynchronous or Synchronous mode.  Sector address supplied during the Secure Silicon Entry command selects the Flash memory array sector that is overlaid by the Secure Silicon Region address map.  Continuous burst mode reads within Secure Silicon Region wrap from address FFh back to address 00h.  Reads outside of the overlaid sector return memory array data.  The Secure Silicon Region is not accessible when the device is executing an Embedded Algorithm (nor during Program Suspend, Erase Suspend, or while another AOS is active).  See the Secure Silicon address map for address range of this area. 8.5.1 Factory Secure Silicon Region The Factory Secure Silicon Region is always protected when shipped from the factory and has the Factory SSR Lock Bit (bit 1) permanently set to a zero. This prevents cloning of a factory locked part and ensures the security of the ESN and customer code once the product is shipped to the field. 8.5.2 Customer Secure Silicon Region The Customer Secure Silicon Region is typically shipped unprotected, Customer SSR Lock Bit (bit 0) set to a one, allowing customers to utilize that sector in any manner they choose.  The Customer Secure Silicon Region can be read any number of times, but each word CL can be programmed only once and the region locked only once. The Customer Secure Silicon Region lock must be used with caution as once locked, there is no procedure available for unlocking the Customer Secure Silicon Region area and none of the bits in the Customer Secure Silicon Region memory space can be modified in any way. The Customer Indicator Bit is located in the SSR Lock at bit location 0.  Once the Customer Secure Silicon Region area is protected, any further attempts to program in the area will fail with status indicating the area being programmed is protected. July 30, 2012 S29VS_XS-R_00_08 S29VS/XS-R MirrorBit® Flash Family 41 Da t a 8.5.3 Sh e e t ( A d va n ce In for ma t i on ) Secure Silicon Region Entry and Exit Command Sequences The system can access the Secure Silicon Region region by issuing the one-cycle Enter Secure Silicon Region Entry command sequence from the IDLE State. The device continues to have access to the Secure Silicon Region region until the system issues the Exit Secure Silicon Region command sequence, performs a Hardware RESET, or until power is removed from the device. See Command Definition Table [Secure Silicon Region Command Table, Appendix Table 11.1 on page 56 for address and data requirements for both command sequences. The Secure Silicon Region Entry Command allows the following commands to be executed  Read customer and factory Secure Silicon Regions  Program the customer Secure Silicon Region  Read data out of all sectors not re-mapped to Secure Silicon Region  Secure Silicon Region Exit Software Functions and Sample Code The following are C functions and source code examples of using the Secured Silicon Sector Entry, Program, and exit commands. Refer to the Spansion Low Level Driver User’s Guide (available soon on www.spansion.com) for general information on Spansion Flash memory software development guidelines. Table 8.1 Secured Silicon Region Entry Cycle Operation Byte Address Word Address Data Entry Cycle Write Sector Address + AAAh Sector Address + 555h 0088h /* Example: SecSi Sector Entry Command */ *( (UINT16 *)sector_address + 0x555 ) = 0x0088; /* write Secsi Sector Entry Cmd */ Table 8.2 Secured Silicon Region Program Cycle Operation Byte Address Word Address Data Program Setup Write Sector Address + AAAh Sector Address + 555h 0025h Write Word Count Write Sector Address + 555h Sector Address + 2AA Word Count (N–1)h Number of words (N) loaded into the write buffer can be from 1 to 32 words. Load Buffer Word N Write Write Buffer to Flash Write Program Address, Word N Sector Address + AAAh Word N Sector Address + 555h 0029h /* Once in the SecSi Sector mode, you program */ /* words using the programming algorithm. */ Table 8.3 Secured Silicon Region Exit Cycle Operation Byte Address Word Address Data Exit Cycle Write Base Address Base Address 00F0h /* Example: SecSi Sector Exit Command */ *( (UINT16 *)base_addr + 0x000 ) = 0x00F0; 42 /* write SecSi Sector Exit cycle */ S29VS/XS-R MirrorBit® Flash Family S29VS_XS-R_00_08 July 30, 2012 Dat a 9. 9.1 S he e t ( Ad van ce I nfor m at i on ) Power Conservation Modes Standby Mode In the standby mode current consumption is greatly reduced, and the outputs (A/DQ15-A/DQ0) are placed in the high impedance state, independent of the OE# input. The device enters the CMOS standby mode when the CE# and RESET# inputs are both held at VCC ± 0.2 V. The device requires standard access time (tCE or tIA) for read access, before it is ready to read data. If the device is deselected during erasure or programming, the device draws active current until the operation is completed. ICC3 in DC Characteristics on page 45 represents the standby current specification 9.2 Automatic Sleep Mode The automatic sleep mode minimizes Flash device energy consumption while in asynchronous mode and while the device is not in a suspended state. The device automatically enables this mode when addresses remain stable for tACC + 20 ns. The automatic sleep mode is independent of the CE#, WE#, and OE# control signals. Standard address access timings (tACC or tPACC) provide new data when addresses are changed. While in sleep mode, output data is latched and always available to the system. While in synchronous mode, the automatic sleep mode is disabled. ICC6 in DC Characteristics on page 45 represents the automatic sleep mode current specification. 9.3 Output Disable (OE#) When the OE# input is at VIH, output (A/DQ15-A/DQ0) from the device is disabled and placed in the high impedance state. RDY is not controlled by OE#. July 30, 2012 S29VS_XS-R_00_08 S29VS/XS-R MirrorBit® Flash Family 43 Da t a Sh e e t ( A d va n ce In for ma t i on ) 10. Electrical Specifications 10.1 Absolute Maximum Ratings Storage Temperature Plastic Packages –65°C to +150°C Ambient Temperature with Power Applied –65°C to +125°C Voltage with Respect to Ground: All Inputs and I/Os except as noted below (Note 1) –0.5 V to VIO + 0.5 V VCC (Note 1) –0.5 V to +2.5 V VIO –0.5 V to +2.5 V VPP (Note 2) –0.5 V to +9.5 V Output Short Circuit Current (Note 3) 100 mA Notes: 1. Minimum DC voltage on input or I/Os is –0.5 V. During voltage transitions, inputs or I/Os may undershoot VSS to –2.0 V for periods of up to 20 ns. See Figure 10.1. Maximum DC voltage on input or I/Os is VCC + 0.5 V. During voltage transitions outputs may overshoot to VCC + 2.0 V for periods up to 20 ns. See Figure 10.2. 2. Minimum DC input voltage on pin VPP is -0.5V. During voltage transitions, VPP may overshoot VSS to –2.0 V for periods of up to 20 ns. See Figure 10.1. Maximum DC voltage on pin VPP is +9.5 V, which may overshoot to 10.5 V for periods up to 20 ns. 3. No more than one output may be shorted to ground at a time. Duration of the short circuit should not be greater than one second. 4. Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational sections of this data sheet is not implied. Exposure of the device to absolute maximum rating conditions for extended periods may affect device reliability. Figure 10.1 Maximum Negative Overshoot Waveform 20 ns 20 ns +0.8 V –0.5 V –2.0 V 20 ns Figure 10.2 Maximum Positive Overshoot Waveform 20 ns VCC +2.0 V VCC +0.5 V 1.0 V 10.2 20 ns 20 ns Operating Ranges Wireless (W) Devices Ambient Temperature (TA) –25°C to +85°C Industrial (I) Devices Ambient Temperature (TA) (Refer to Publication Number S29VS_XS-R_SP for Industrial Temperature specific differences) –40°C to +85°C Supply Voltages VCC Supply Voltages +1.70 V to +1.95 V +1.70 V to +1.95 V VIO Supply Voltages VCC(min)  VIO(min) - 200mV Note: Operating ranges define those limits between which the functionality of the device is guaranteed. 44 S29VS/XS-R MirrorBit® Flash Family S29VS_XS-R_00_08 July 30, 2012 Dat a 10.3 S he e t ( Ad van ce I nfor m at i on ) DC Characteristics 10.3.1 CMOS Compatible Parameter Max Unit ILI Input Load Current Description VIN = VSS to VCC, VCC = VCCmax Test Conditions (Notes 1 & 2) Min ±1 µA ILO Output Leakage Current VOUT = VSS to VCC, VCC = VCCmax ±1 µA 35 38 mA 39 44 mA 28 30 mA 32 36 mA 28 30 mA 32 36 mA 83 MHz CE# = VIL, OE# = VIH, WE# = VIH, burst length = 8 104 MHz 108 MHz 83 MHz ICCB VCC Active burst Read Current CE# = VIL, OE# = VIH, WE# = VIH, burst length = 16 104 MHz 108 MHz CE# = VIL, OE# = VIH, WE# = VIH, burst length = Continuous 83 MHz 104 MHz 108 MHz Typ IIO1 VIO Non-active Output OE# = VIH, RDY = Tri-State 20 30 µA IIO2 VIO Standby CE# = RESET# = VCC ± 0.2V 2 3 µA ICC1 VCC Active Asynchronous Read Current CE# = VIL, OE# = VIH, WE# = VIH ICC2 VCC Active Write Current (3) (7) CE# = VIL, OE# = VIH, VPP = VIH ICC3 VCC Standby Current CE# = RESET# = VCC ± 0.2 V ICC4 VCC Reset Current RESET# = VIL, CLK = VIL 10 MHz 40 60 mA 5 MHz 20 40 mA 1 MHz 10 20 mA VPP 1 5 µA VCC 30 40 mA VPP 1 5 µA VCC 83 MHz VCC Active Current (Read While Write) (Continuous Burst) (6) CE# = VIL, OE# = VIH, VPP = VIH 104 MHz ICC6 VCC Sleep Current (4) CE# = VIL, OE# = VIH IPP Accelerated Program Current (5) CE# = VIL, OE# = VIH, VPP = 9.5 V ICC5 30 40 µA 150 250 µA 65 70 71 76 20 40 mA 108 MHz µA VPP 7 10 mA VCC 25 28 mA V VIL Input Low Voltage VIO = 1.8 V –0.2 0.4 VIH Input High Voltage VIO = 1.8 V VIO – 0.4 VIO + 0.4 VOL Output Low Voltage IOL = 100 µA, VCC = VCC min = VIO VOH Output High Voltage IOH = –100 µA, VCC = VCC min = VIO VHH Voltage for Accelerated Program 8.5 9.5 V VLKO Low VCC Lock-out Voltage 1.0 1.1 V 0.1 VIO – 0.1 V V Notes: 1. Maximum ICC specifications are tested with VCC = VCCmax. 2. VCC= VIO 3. ICC active while Embedded Erase or Embedded Program is in progress. 4. Device enters automatic sleep mode when addresses are stable for tACC + 20 ns. Typical sleep mode current is equal to ICC3. 5. Total current during accelerated programming is the sum of VPP and VCC currents. 6. ICC5 applies while reading the status register during program and erase operations. 7. Effect of status register polling during write not included. July 30, 2012 S29VS_XS-R_00_08 S29VS/XS-R MirrorBit® Flash Family 45 Da t a 10.4 Sh e e t ( A d va n ce In for ma t i on ) Capacitance Symbol Description CIN Input Capacitance (Address, CE#, OE#, WE#, AVD#, WE#, CLK, RESET#) VIN = 0 COUT Output Capacitance (DQ, RDY) VOUT = 0 Min. Typ. Max. Unit Single Die 2.0 4.5 6.0 pF Dual Die 4.0 9.0 12.0 pF Test Condition Single Die 2.0 4.5 6.0 pF Dual Die 4.0 9.0 12.0 pF Notes: 1. Test conditions TA = 25°C, f = 1.0 MHz 2. Sampled, not 100% tested. 10.5 AC Test Conditions Operating Range Input level 0.0 to VIO Input comparison level VIO/2 Output data comparison level VIO/2 Load capacitance (CL) 30 pF Transition time (tT) (input rise and fall times) Transition time (tT) (CLK input rise and fall times) 83 MHz 2.50 ns 104 MHz 1.85 ns 108 MHz 1.85 ns 83 MHz 2.50 ns 104 MHz 1.85 ns 108 MHz 1.85 ns Figure 10.3 Input Pulse and Test Point VIO VIO /2 Input and Output Test Point VIO /2 0V Figure 10.4 Output Load Device Under Test *CL = 30 pF including scope and Jig capacitance 10.6 Key to Switching Waveforms Waveform Inputs Outputs Steady Changing from H to L Changing from L to H 46 Don’t Care, Any Change Permitted Changing, State Unknown Does Not Apply Center Line is High Impedance State (High-Z) S29VS/XS-R MirrorBit® Flash Family S29VS_XS-R_00_08 July 30, 2012 Dat a 10.7 S he e t ( Ad van ce I nfor m at i on ) VCC Power Up Table 10.1 VCC Power-up Parameter Description Test Setup Speed tVCS VCC Setup Time Min 300 Unit µs tVIOS VIO Setup Time Min 300 µs tRH Time between RESET# (high) and CE# (low) Min 200 ns Notes: 1. RESET# must be high after VCC and VIO are higher than VCC minimum. 2. VCC  VIO – 200 mV during power-up. 3. VCC & VIO ramp rate could be non-linear 4. VCC and VIO are recommended to be ramped up simultaneously. Figure 10.5 VCC Power-up Diagram . tVCS VCC min VCC tVIOS VIO min VIO VIH RESET# tRH CE# 10.8 CLK Characterization Parameter fCLK Description 108 MHz Max 108 Min DC (1) CLK Frequency Unit MHz tCLK CLK Period Min 9.26 ns tCL/tCH CLK Low/High Time Min 0.40 tCLK ns Note: 1. DC for operations other than continuous and 16 word (32 byte) synchronous burst read. See AC Characteristics Table. Figure 10.6 CLK Characterization tCLK tCH tCL CLK July 30, 2012 S29VS_XS-R_00_08 S29VS/XS-R MirrorBit® Flash Family 47 Da t a 10.9 Sh e e t ( A d va n ce In for ma t i on ) AC Characteristics 10.9.1 AC Characteristics–Synchronous Burst Read Parameter (Notes) Symbol 83 MHz 104 MHz 108 MHz DC (0) for operations other than continuous and 32 byte synchronous burst. Unit KHz Clock Frequency CLK Min Clock Cycle tCLK Min 12 9.6 9.26 ns CLK Rise Time tCLKR Max 2.5 1.92 1.852 ns CLK Fall Time tCLKF tCLKH/L Min 5 tIA Max tBACC Max AVD# Setup Time to CLK tAVDS Min AVD# Hold Time from CLK tAVDH Min Address Setup Time to CLK tACS Min Address Hold Time from CLK tACH Min Data Hold Time from Next Clock Cycle tBDH Min CLK High or Low Time Internal Access Time Burst Access Time Valid Clock to Output Delay 120 in 32 Byte burst 1000 in continuous burst 4 3.86 ns 72.34 ns 6.75 ns 4 3.38 ns 3 2.89 ns 4 2.89 ns 75 9 7.6 5 3 2 4.82 ns 2 ns Output Enable to Data tOE Max 15 ns CE# Disable to Output High-Z (2) tCEZ Max 10 ns OE# Disable to Output High-Z (2) tOEZ Max CE# Setup Time to CLK tCES Min CLK to RDY valid tRACC Max tCR Max 10 ns tAVDP Min 6 ns CE# low to RDY valid AVD# Pulse Width 10 ns 4 9 7.6 3.38 ns 6.75 ns Notes: 1. Not 100% tested. 2. If OE# is disabled before CE# is disabled, the output goes to High-Z by tOEZ. If CE# is disabled before OE# is disabled, the output goes to High-Z by tCEZ. If CE# and OE# are disabled at the same time, the output goes to High-Z by tOEZ. 3. AVD can not be low for 2 subsequent CLK cycles. Figure 10.7 Synchronous Read Mode - ADM Interface tCES 7 cycles for initial access is shown as an illustration. CE# 1 2 3 4 5 6 7 CLK tAVDS AVD# tAVDP tAVDH tACS Amax– A16 AC A/DQ15– A/DQ0 AC tACH DD tIA tCR 48 DE DB tBDH OE# RDY tBACC DC tOE tRACC Hi-Z S29VS/XS-R MirrorBit® Flash Family S29VS_XS-R_00_08 July 30, 2012 Dat a 10.9.2 S he e t ( Ad van ce I nfor m at i on ) AC Characteristics–Asynchronous Read Symbol Min Max Access Time from CE# Low Parameter tCE – 80 Asynchronous Access Time from address valid tACC – 80 Read Cycle Time tRC 80 – AVD# Low Time tAVDP 6 – Address Setup to rising edge of AVD# tAAVDS 4 – Address Hold from rising edge of AVD# tAAVDH 3.5 – Output Enable to Output Valid tOE – 15 CE# Setup to AVD# falling edge tCAS 0 – CE# Disable to Output & RDY High-Z (1) tCEZ – 10 OE# Disable to Output High-Z (1) tOEZ – 10 AVD# High to OE# Low tAVDO 4 – tCR – 10 WE# Disable to AVD# Enable tWEA 9.6 – WE# Disable to OE# Enable tOEH 4 – CE# low to RDY valid Unit ns Notes: 1. Not 100% tested. 2. If OE# is disabled before CE# is disabled, the output goes to High-Z by tOEZ. If CE# is disabled before OE# is disabled, the output goes to High-Z by tCEZ. If CE# and OE# are disabled at the same time, the output goes to High-Z by tOEZ. Figure 10.8 Asynchronous Mode Read - ADM Interface CE# tOE OE# tOEH WE# tCE A/DQ15– A/DQ0 tOEZ RA Valid RD tACC RA Amax–A16 tAAVDH AVD# tCAS tAVDP tAAVDS tCR RDY tCEZ Hi-Z Hi-Z Notes: 1. AVD# Transition occurs after CE# is driven to Low and Valid Address Transition occurs before AVD# is driven to Low. 2. VA = Valid Read Address, RD = Read Data. July 30, 2012 S29VS_XS-R_00_08 S29VS/XS-R MirrorBit® Flash Family 49 Da t a 10.9.3 Sh e e t ( A d va n ce In for ma t i on ) AC Characteristics–Erase/Program Timing Parameter Symbol Min Typ Max tWC 60 – – ns AVD# low pulse width tAVDP 6 – – ns Address Setup to rising edge of AVD# tAAVDS 4 – – ns Address Hold from rising edge of AVD# tAAVDH 3.5 – – ns Read Recovery Time Before Write tGHWL 0 – – ns Data Setup to rising edge of WE# tDS 20 – – ns Data Hold from rising edge of WE# tDH 0 – – ns CE# Setup to falling edge of WE# tCS 4 – – ns CE# Hold from rising edge of WE# tCH 0 – – ns WE# Pulse Width tWP 25 – – ns WE# Pulse Width High tWPH 20 – – ns WE# Cycle Time (1) Unit Latency Between Read and Write Operations tSRW 0 – – ns AVD# Disable to WE# Disable tVLWH 23.5 – – ns WE# Disable to AVD# Enable tWEA 9.6 – – ns tCR – – 10 ns CE# Disable to Output High-Z tCEZ – – 10 ns OE# Disable to WE# Enable tWEH 4 – – ns Erase Suspend Latency tESL – – 30 µs Program Suspend Latency tPSL – – 30 µs Erase Resume to Erase Suspend tERS 30 – – µs Program Resume to Program Suspend tPRS 30 – – µs CE# low to RDY valid Note: 1. Sampled, not 100% tested. Figure 10.9 Asynchronous Program Operation Timings - ADM Interface Program Command Sequence (last two cycles) VIH Read Status Data CLK VIL tVLWH tAVDP AVD# tAAVDH tAAVDS Amax– A16 A/DQ15– A/DQ0 BA(555h) SA(555h) PA PA PD SA(555h) BA(555h) 29h BA 70h BA Status tDS tDH tCAS CE# tCH OE# tWP WE# tCS tWPH tWC tVCS + tRH VCC 50 S29VS/XS-R MirrorBit® Flash Family S29VS_XS-R_00_08 July 30, 2012 Dat a 10.9.4 S he e t ( Ad van ce I nfor m at i on ) Hardware Reset (Reset#) Table 10.2 Warm-Reset Parameter JEDEC Std Description All Speed Options Unit tRP RESET# Pulse Width Min 50 ns tRH Reset High Time Before Read Min 200 ns tRPH RESET# Low to CE# Low Min 10 us Figure 10.10 Reset Timings CE#, OE# tRH RESET# tRP tRPH Figure 10.11 Latency with Boundary Crossing Address boundary occurs every 128 words, beginning at address 00007Fh: (0000FFh, 00017Fh, etc.) Address 000000h is also a boundary crossing. Address (hex) CLK AVD# 7C 7D 7E 7F 7F 80 83 tRACC tRACC latency tRACC RDY (Note 2) OE#, CE# 82 (stays high) RDY (Note 1) Data 81 tRACC latency D124 D125 D126 D127 D128 D129 D130 (stays low) Notes: 1. RDY active with data (CR.8 = 1 in the Configuration Register). 2. RDY active one clock cycle before data (CR.8 = 0 in the Configuration Register). 3. Figure shows the device not crossing a bank in the process of performing an erase or program. July 30, 2012 S29VS_XS-R_00_08 S29VS/XS-R MirrorBit® Flash Family 51 Da t a Sh e e t ( A d va n ce In for ma t i on ) Figure 10.12 Latency with Boundary Crossing into Bank Performing Embedded Operation Address boundary occurs every 128 words, beginning at address 00007Fh: (0000FFh, 00017Fh, etc.) Address 000000h is also a boundary crossing. Address (hex) CLK AVD# 7C 7D 7E 7F 7F 80 D127 00h 81 82 83 (stays high) tRACC RDY (Note 1) tRACC RDY (Note 2) Data OE#, CE# D124 D125 D126 00h 00h 00h (stays low) Notes: 1. RDY active with data (CR.8 = 1 in the Configuration Register). 2. RDY active one clock cycle before data (CR.8 = 0 in the Configuration Register). 3. Figure shows the device crossing a bank in the process of performing an erase or program. 52 S29VS/XS-R MirrorBit® Flash Family S29VS_XS-R_00_08 July 30, 2012 Dat a 10.9.5 S he e t ( Ad van ce I nfor m at i on ) Wait State Configuration Register Setup Figure 10.13 Example of Programmable Wait States Data D0 D1 Rising edge of next clock cycle following last wait state triggers next burst data AVD# Total number of clock cycles following addresses being latched OE# 1 2 3 4 6 5 7 CLK 1 0 2 4 3 5 6 7 Total number of clock edges following addresses being latched Configuration Register Programmable Wait States 0000 = Reserved 0001 = 3rd 0010 = 4th 0011 = 5th CR.13 0100 = 6th CR.12 0101 = CR.14 CR.11 0110 = 7th initial data is valid on the 8th 0111 = 9th 1000 = 10th . . . . . . 1011 = 13th rising CLK edge after addresses are latched 1100 = Reserved 1111 = July 30, 2012 S29VS_XS-R_00_08 S29VS/XS-R MirrorBit® Flash Family 53 Da t a Sh e e t ( A d va n ce In for ma t i on ) Figure 10.14 Back-to-Back Read/Write Cycle Timings - ADM Interface Last Cycle in Program or Sector Erase Command Sequence Read status (at least two cycles) in same bank and/or array data from other bank tWC tRC Begin another write or program command sequence tRC tWC CE# OE# tOE tOEH tGHWL WE# tWPH tWP tACC tDS tOEZ tDH Data RD WD 25h RD tSR/W Addresses WA RA RA SA(555h) tAAVDS AVD# tAAVDH Note: Breakpoints in waveforms indicate that system may alternately read array data from the non-busy bank while checking the status of the program or erase operation in the busy bank. The system should read status twice to ensure valid information. 54 S29VS/XS-R MirrorBit® Flash Family S29VS_XS-R_00_08 July 30, 2012 Dat a 10.9.6 S he e t ( Ad van ce I nfor m at i on ) Erase and Programming Performance Parameter Typ (Note 1) Max (Note 2) 128 Kbyte VCC 0.8/1.3 3.5/5.5 Sector Erase Time 32 Kbyte VCC 0.35/0.6 2.0/3.5 (Note 6) 128 Kbyte VPP 0.8/1.3 3.5/5.5 32 Kbyte VPP 0.35/0.6 2.0/3.5 78/126 (128 Mbit) 200/325 (128 Mbit) 155/251 (256 Mbit) 400/650 (256 Mbit) 78/126 (128 Mbit) 154/250 (128 Mbit) 155/251 (256 Mbit) 308/500 (256 Mbit) VCC 170 800 VCC 14.1 94 VPP 9 48 VCC 450 3000 VPP 288 1540 118 (128 Mbit) 157 (128 Mbit) 236 (256 Mbit) 315 (256 Mbit) 76 (128 Mbit) 80 (128 Mbit) 151 (256 Mbit) 160 (256 Mbit) VCC Unit Comments s (Note 3) µs Excludes system level overhead (Note 4) s Excludes system level overhead (Note 4) Chip Erase Time (Note 6), (Note 7) VPP Single Word Program Time (using Program Buffer) Effective Word Programming Time using Program Write Buffer Total 32-Word Buffer Programming Time VCC Chip Programming Time (using 32 word buffer) VPP Erase Suspend/Erase Resume (tESL) 30 µs Program Suspend/Program Resume (tPSL) 30 µs Blank Check 1 ms Notes: 1. Typical program and erase times assume the following conditions: 25°C, 1.8 V VCC, 10,000 cycles. Additionally, programming typically assumes a checkerboard pattern. 2. Under worst case conditions of –25°C, VCC = 1.70 V, 100,000 cycles. 3. In the pre-programming step of the Embedded Erase algorithm, all words are programmed to 00h before erasure. 4. System-level overhead is the time required to execute the bus-cycle sequence for the program command. See Table 11.1 on page 56 for further information on command definitions. 5. The device has a minimum erase and program cycle endurance of 10,000 cycles. 6. The first value excludes pre-programming time, while the second value is inclusive of pre-programming time for the FFFFh pattern, with status polling rate as 400 ns. 7. The erase time is calculated from the time of issuing erase command to the completion of erase operation (indicated by status register) July 30, 2012 S29VS_XS-R_00_08 S29VS/XS-R MirrorBit® Flash Family 55 Da t a Sh e e t ( A d va n ce In for ma t i on ) 11. Appendix This section contains information relating to software control or interfacing with the Flash device. 11.1 Command Definitions All values are in hexadecimal. The S29VS-R family of devices are 16-bit word address oriented. Most system address buses, regardless of data bus size, are byte oriented. It is common practice for system designers to shift the address busses. That is, Flash Address A0 is connected to system Address A1, etc. To accommodate the system designers, addresses are listed in both word address and byte address where applicable. The flash address (word) is listed above the system address (byte). Command Sequence Cycles Table 11.1 Command Definitions (Sheet 1 of 2) Bus Cycles (Notes 1–4) First Second Addr Data RA RD 1 X F0 3-34 (SA) 555 (SA) AAA 25 Buffer to Flash 1 (SA) 555 (SA) AAA 29 Chip Erase 2 (SA) 555 (SA) AAA Sector Erase 2 Read Status Register Third Addr Data (SA) 2AA (SA) 554 WC 80 (SA) 2AA (SA) 554 10 (SA) 555 (SA) AAA 80 (SA) 2AA (SA) 554 30 2 (SA) 555 (SA) AAA 70 (SA) RR Clear Status Register 1 (SA) 555 (SA) AAA 71 Program Suspend (5) 1 XXX 51 Program Resume (5) 1 (SA) 000 50 Erase Suspend (6) 1 XXX B0 Erase Resume (6) 1 (SA) 000 30 Read Reset Write Buffer Load (8) (SA) 555 Addr (SA) PA (11) Fourth Data Addr Data PD PA (12) PD SLA 61 Blank Check (13) 1 Sector Lock/Unlock 3 555 AAA 60 2AA 554 60 SLA 60 Sector Lock Range 4 555 AAA 60 2AA 554 60 SLA 61 (SA) X00 PD (SA) AAA 33 ID/CFI ID/CFI Command Definitions (SA) X55 ID/CFI Entry (7) (10) 1 ID/CFI Read 1 (SA) RA data ID/CFI Exit 1 XXX FO (SA) XAA 90 or 98 Configuration Register Configuration Command Definitions 56 (SA) 555 Configuration Register Entry (7) (10) 1 Write Buffer Load 3 Buffer to Flash (Configuration Register) 1 Configuration Register Read 1 (SA) X00 RR Configuration Register Exit 1 XXX FO (SA) AAA (SA) 555 (SA) AAA (SA) 555 (SA) AAA D0 25 (SA) 2AA (SA) 554 0 29 S29VS/XS-R MirrorBit® Flash Family S29VS_XS-R_00_08 July 30, 2012 Dat a S he e t ( Ad van ce I nfor m at i on ) Command Sequence Cycles Table 11.1 Command Definitions (Sheet 2 of 2) Bus Cycles (Notes 1–4) First Addr Second Data Addr Third Data Fourth Addr Data (SA) 00 PD (SA) PA PD Addr Data (SA) PA PD SSR Lock SSR Lock Command Definitions (SA) 555 SSR Lock Entry (7) (10) 1 Write Buffer Load (8) 3 Buffer to Flash 1 SSR Lock Read 1 (SA) XXX SSR Lock Exit 1 XXX (SA) AAA (SA) 555 (SA) AAA (SA) 555 (SA) AAA 40 25 (SA) 2AA (SA) 554 0 29 RR F0 Secure Silicon Region Secure Silicon Region Command Definitions Secure Silicon Region Entry (7) (10) Write Buffer Load (8) 1 3-34 (SA) 555 (SA) AAA (SA) 555 (SA) AAA (SA) 555 88 25 Buffer to Flash 1 Secure Silicon Region Read 1 (SA) RA RD Secure Silicon Region Exit 1 XXX F0 (SA) AAA (SA) 2AA (SA) 554 WC 29 Legend: X = Don’t care RA = Address of the location to be read. RD = Read Data from location RA during read operation. RR = Read Register value PA = Address of the memory location to be programmed. PD = Data to be programmed at location PA. BA = Address bits sufficient to select a bank SA = Address bits sufficient to select a sector SLA = Sector Lock Address WBL = Write Buffer Location. Address must be within the same write buffer page as PA. WC = Word Count. Number of write buffer locations to load minus 1. Notes: 1. See Section 7., Device Operations on page 21 for description of bus operations. 2. Except for the following, all bus cycles are write cycle: read cycle during Read, ID/CFI Read (Manufacturing ID, Device ID, Indicator Bits), Configuration Register read, Secure Silicon Region Read, SSR Lock Read, and 2nd cycle of Status Register Read. 3. Data bits DQ15–DQ8 are don’t care in command sequences, except for RD, PD, and WD. 4. Writing incorrect address and data values or writing them in the improper sequence may place the device in an unknown state. The system must write the reset command to return the device to reading array data. 5. The Program Resume command is valid only during the Program Suspend mode/state. 6. The Erase Resume command is valid only during the Erase Suspend mode/state. 7. Command is valid when all banks are ready to read array data. 8. The total number of cycles in the command sequence is determined by the number of words written to the write buffer. 9. VPP must be at VHH during the entire operation of this command. 10. Entry commands are needed to enter a specific mode to enable instructions only available within that mode. 11. Must be the lowest word address of the words being programmed within the 32 word write buffer page. This is not necessarily the lowest address of the page. Data words are loaded into the write page buffer in sequential order from lowest to highest address. 12. Subsequent addresses must fall within the same Sector and Page as the initial starting address. 13. Blank Check is only functional in Asynchronous Read mode (Configuration Register - CR [15] = 1). July 30, 2012 S29VS_XS-R_00_08 S29VS/XS-R MirrorBit® Flash Family 57 Da t a 11.2 Sh e e t ( A d va n ce In for ma t i on ) Device ID and Common Flash Memory Interface Address Map The Device ID fields occupy the first 32 bytes of address space followed by the Common Flash Interface data structure. The Common Flash Interface (CFI) specification defines a standardized data structure containing device specific parameter, structure, and feature set information, which allows vendor-specified software algorithms to be used for entire families of devices. Software support can then be device-independent, JEDEC ID-independent, and forward- and back-ward-compatible for the specified flash device families. Flash driver software can be standardized for long-term compatibility. This device enters the ID/CFI mode when the system writes the ID/CFI Query command, 90h or 98h, to address (SA)55h any time all banks are in read mode (the CU is in Idle State). The system can then read ID and CFI information at the addresses, within the selected sector, given in the following tables. To terminate reading ID/CFI, the system must write the reset command. Table 11.2 ID/CFI Data (Sheet 1 of 5) Device Identification DATA Word Offset Address Byte Offset Address VS256R/XS256R (SA) + 00h (SA) + 00h VS128R/XS128R (SA) + 01h (SA) + 02h (SA) + 02h (SA) + 04h Reserved (SA) + 03h (SA) + 06h Reserved Reserved (SA) + 04h (SA) + 08h Reserved Reserved (SA) + 05h (SA) + 0Ah Reserved Reserved (SA) + 06h (SA) + 0Ch 0010h ID Version 0001h 007Eh (Top/Bottom) Description Spansion Manufacturer ID 007Eh (Top/Bottom) DQ15 - DQ8 = Reserved DQ7 - Factory Lock Bit: 1 = Locked; 0 = Not Locked DQ6 - Customer Lock Bit: 1 = Locked; 0 = Not locked DQ5 - DQ0 = Reserved Device ID, Word 1 Extended ID address code. Indicates an extended two byte device ID is located at byte address 1Ch and 1Eh. Reserved (SA) + 07h (SA) + 0Eh (SA) + 08h (SA) + 10h Reserved (SA) + 09h (SA) + 12h Reserved Reserved (SA) + 0Ah (SA) + 14h Reserved Reserved (SA) + 0Bh (SA) + 16h Reserved Reserved Indicator Bits Reserved 05h Bit 0 - Status Register Support 1 = Status Register Supported 0 = Status register not Supported (SA) + 0Ch (SA) + 18h Bit 1 - DQ Polling Support 1 = DQ bits polling supported 0 = DQ bits polling not supported Lower Software Bits Bit 3-2 - Command Set Support 11 = Reserved 10 = Reserved 01 = Reduced Command Set 00 = Old Command Set Bit 4- F - Reserved 58 Reserved Upper Software Bits Reserved (SA) + 0Dh (SA) + 1Ah (SA) + 0Eh (SA) + 1Ch 0064h/Top; 0066h/Bottom 0063h/Top; 0065h/Bottom High Order Device ID, Word 2 (SA) + 0Fh (SA) + 1Eh 0001h (Top/Bottom) 0001h (Top/Bottom) Low Order Device ID, Word 3 S29VS/XS-R MirrorBit® Flash Family S29VS_XS-R_00_08 July 30, 2012 Dat a S he e t ( Ad van ce I nfor m at i on ) Table 11.2 ID/CFI Data (Sheet 2 of 5) DATA Word Offset Address Byte Offset Address VS256R/XS256R VS128R/XS128R Description CFI Query Identification String (SA) + 10h (SA) + 20h 0051h (SA) + 11h (SA) + 22h 0052h (SA) + 12h (SA) + 24h 0059h (SA) + 13h (SA) + 26h 0002h (SA) + 14h (SA) + 28h 0000h (SA) + 15h (SA) + 2Ah 0040h (SA) + 16h (SA) + 2Ch 0000h (SA) + 17h (SA) + 2Eh 0000h (SA) + 18h (SA) + 30h 0000h (SA) + 19h (SA) + 32h 0000h (SA) + 1Ah (SA) + 34h 0000h Query Unique ASCII string “QRY” CFI Primary Algorithm Command Set (Spansion = 0002h) Address for Primary Extended Table Alternate Algorithm Command Set (00h = none exists) Address for Secondary Algorithm extended Query Table (00h = none exists) Common Flash Interface System Interface String VCC Logic Supply Minimum Program/Erase or Write voltage (SA) + 1Bh (SA) + 36h 0017h (SA) + 1Ch (SA) + 38h 0019h (SA) + 1Dh (SA) + 3Ah 0085h VPP [Programming] Supply Minimum Program/Erase voltage (00h = no VPP pin present) (SA) + 1Eh (SA) + 3Ch 0095h VPP [Programming] Supply Maximum Program/Erase voltage (00h = no VPP pin present) (SA) + 1Fh (SA) + 3Eh 0008h Typical Word Programming Time per single word 2N s (e.g. < or = 32 s) (SA) + 20h (SA) + 40h 0009h Typical Program Time for programming the complete buffer 2N s (e.g. < or = 256 s) (00h = not supported) (SA) + 21h (SA) + 42h 000Ah Typical Time for Sector Erase 2N ms (SA) + 22h (SA) + 44h (SA) + 23h (SA) + 46h 0003h Max. Program Time per single word [2N times typical value] (SA) + 24h (SA) + 48h 0003h Max. Program Time using buffer [2N times typical value] (SA) + 25h (SA) + 4Ah 0003h Max. Time for sector erase [2N times typical value] (SA) + 26h (SA) + 4Ch 0003h Max. Time for full chip erase [2N times typical value] (00h = not supported) July 30, 2012 S29VS_XS-R_00_08 0012h D7-D4: Volt D3-D0: 100 millivolt VCC Logic Supply Maximum Program/Erase or Write voltage D7-D4: Volt D3-D0: 100 millivolt 0011h S29VS/XS-R MirrorBit® Flash Family Typical Time for full chip erase 2N s (00h = not supported) 59 Da t a Sh e e t ( A d va n ce In for ma t i on ) Table 11.2 ID/CFI Data (Sheet 3 of 5) DATA Word Offset Address Byte Offset Address VS256R/XS256R VS128R/XS128R Description Device Geometry Definition (SA) + 27h (SA) + 4Eh 0019h 0018h Device Size = 2N byte Common Flash Interface Flash Device Interface 0h = x8 1h = x16 2h = x8/x16 3h = x32 [lower byte] (SA) + 28h (SA) + 50h 0001h (SA) + 29h (SA) + 52h 0000h [upper byte] (00h = not supported) (SA) + 2Ah (SA) + 54h 0006h Max. number of bytes in multi-byte buffer write = 2N [lower byte] (SA) + 2Bh (SA) + 56h 0000h [upper byte] (00h = not supported) (SA) + 2Ch (SA) + 58h 0002h Number of Erase Block Regions within device (Number of regions within the device containing one or more contiguous Erase Blocks of the same size) (SA) + 2Dh (SA) + 2Eh 00FEh 007Eh (Top Boot) (Top Boot) (SA) + 5Ah 0003h 0003h (Bottom Boot) (Bottom Boot) (SA) + 5Ch 0000h [upper byte] 0000h (Top Boot) (SA) + 2Fh Erase Block Region 1 information [lower byte] - Number of Erase sectors of identical size within the Erase Block Region. 00h = 1 sector; 01h = 2 sectors 02h = 3 sectors 03h = 4 sectors (SA) + 5Eh 0080h (Bottom Boot) [lower byte] - Sector Size in bytes divided by 256 (n [bytes]h = sector size / 256) 0002h (Top Boot) (SA) + 30h (SA) + 60h [upper byte] 0000h (Bottom Boot) (SA) + 31h 0003h 0003h (Top Boot) (Top Boot) 00FEh 007Eh (SA) + 62h Erase block Region 2 Information (Bottom Boot) (SA) + 32h (SA) + 64h (Bottom Boot) 0000h 0080h (Top Boot) (SA) + 33h (SA) + 66h 0000h (Bottom Boot) [upper byte] [lower byte] - Sector Size in bytes divided by 256 (n [bytes]h = sector size / 256) 0000h (Top Boot) (SA) + 34h (SA) + 68h [upper byte] 0002h (Bottom Boot) 60 S29VS/XS-R MirrorBit® Flash Family S29VS_XS-R_00_08 July 30, 2012 Dat a S he e t ( Ad van ce I nfor m at i on ) Table 11.2 ID/CFI Data (Sheet 4 of 5) DATA Word Offset Address Byte Offset Address VS256R/XS256R VS128R/XS128R Description Primary Algorithm-Specific Extended Query (SA) + 40h (SA) + 80h 0050h (SA) + 41h (SA) + 82h 0052h (SA) + 42h (SA) + 84h 0049h (SA) + 43h (SA) + 86h 0031h (SA) + 44h (SA) + 88h 0034h Minor CFI version number, ASCII Address Sensitive Unlock (Bits 1-0): 00b = Required 01b = Not required Process Technology (Bits 5-2) 0011b = 130 nm Floating-Gate Technology 0100b = 110 nm MirrorBit Technology 0101b = 90 nm Floating-Gate Technology 0110b = 90 nm MirrorBit Technology 1000b = 65 nm MirrorBit Technology (SA) + 45h (SA) + 8Ah 0020h (SA) + 46h (SA) + 8Ch 0002h (SA) + 47h (SA) + 8Eh 0001h (SA) + 48h (SA) + 90h 0000h Query Unique ASCII string “PRI” Major CFI version number, ASCII Erase Suspend 0= Not supported 1 = To Read Only 2 = To Read & Write Common Flash Interface Sector Protection per Group 0 = not Supported X = number of sectors in per group Sector Temporary Unprotect 00h = Not Supported 01h = Supported (SA) + 49h (SA) + 92h (SA) + 4Ah (SA) + 94h (SA) + 4Bh (SA) + 96h (SA) + 4Ch (SA) + 98h Sector Protect/Unprotect scheme 08h = Advanced Sector Protection 09h = Single-Sector Lock + Sector Lock Range 0009h 00E0h 0070h 0001h 0000h Simultaneous Operations Number of Sectors in all banks except Boot Bank Burst Mode Type 00h = Not Supported 01h = Supported Page Mode Type 00h = Not Supported 01h = 4-Word Page 02h = 8-Word Page 04h = 16-Word Page (SA) + 4Dh (SA) + 9Ah 0085h VPP (Acceleration) Supply Minimum 00h = Not Supported D7-D4: Volt D3-D0: 100 millivolt (SA) + 4Eh (SA) + 9Ch 0095h VPP (Acceleration) Supply Maximum 00h = Not Supported D7-D4: Volt D3-D0: 100 millivolt Top/Bottom Sector Flag (SA) + 4Fh (SA) + 9Eh (SA) + 50h (SA) + A0h 03h (Top Boot) 02h (Bottom Boot) 00h = Uniform 01h = Dual Boot 02h = Bottom boot 03h = Top boot Program Suspend July 30, 2012 S29VS_XS-R_00_08 0001h S29VS/XS-R MirrorBit® Flash Family 00h = Not Supported 01h= Supported 61 Da t a Sh e e t ( A d va n ce In for ma t i on ) Table 11.2 ID/CFI Data (Sheet 5 of 5) DATA Word Offset Address Byte Offset Address VS256R/XS256R VS128R/XS128R Description Common Flash Interface Unlock Bypass (SA) + 51h (SA) + A2h 0000h (SA) + 52h (SA) + A4h 0008h Secure Silicon Region (Customer SSR Area) Size 2N bytes (SA) + 53h (SA) + A6h 000Eh Hardware Reset Low Time-out until reset is completed during an embedded algorithm - Maximum 2N ns (e.g. 10 s => n = E) (SA) + 54h (SA) + A8h 000Eh Hardware Reset Low Time-out until reset is completed not during an embedded algorithm - Maximum 2N ns (e.g. 10 s => n = E) (SA) + 55h (SA) + AAh 0005h Erase Suspend Time-out Maximum 2N µs (SA) + 56h (SA) + ACh 0005h Program Suspend Time-out Maximum 2N µs (SA) + 57h (SA) + AEh 0008h Bank Organization: X= Number of banks Common Flash Interface (SA) + 58h 0020h 0010h (Top Boot) (Top Boot) 0023h 0013h (Bottom Boot) (Bottom Boot) (SA) + B0h Bank 0 Region Information. X= Number of sectors in bank (SA) + 59h (SA) + B2h 0020h 0010h Bank 1 Region Information. X= Number of sectors in bank (SA) + 5Ah (SA) + B4h 0020h 0010h Bank 2 Region Information. X= Number of sectors in bank (SA) + 5Bh (SA) + B6h 0020h 0010h Bank 3 Region Information. X= Number of sectors in bank (SA) + 5Ch (SA) + B8h 0020h 0010h Bank 4 Region Information. X= Number of sectors in bank (SA) + 5Dh (SA) + BAh 0020h 0010h Bank 5 Region Information. X= Number of sectors in bank (SA) + 5Eh (SA) + BCh 0020h 0010h Bank 6 Region Information. X= Number of sectors in bank (SA) + 5Fh 62 00h = Not Supported 01h = Supported 0020h 0010h (Bottom Boot) (Bottom Boot) 0023h 0013h (Top Boot) (Top Boot) (SA) + BEh S29VS/XS-R MirrorBit® Flash Family Bank 7 Region Information. X= Number of sectors in bank S29VS_XS-R_00_08 July 30, 2012 Dat a S he e t ( Ad van ce I nfor m at i on ) Figure 11.1 Asynchronous Read - AADM Interface CLK may be at VIL or VIH or Active CLK CE# tAVDP tAVDP tCAS tAVDP OE# low with AVD# low signals the presence of Address-High. The Address-High cycle is optional. When the high part of address does not change only the Address-Low cycle is needed. AVD# tAAVDS tAAVDS tAAVDH tAAVDH OE# enables data output only after the Address-Low cycle in which AVD# is Low and OE# is High OE# is ignored after OE# returns high between accesses until the next Address-Low is received OE# WE# tACC tAAVDS tAAVDH tCE tAAVDS tOE tAAVDH A/DQ15A/DQ0 tCEZ tOEZ tACC Add-Hi Add-Low Data tCR tCR RDY Figure 11.2 Asynchronous Read Followed By Read - AADM Interface CLK may be at VIL or VIH or Active CLK CE# tCAS tAVDP AVD# tAVDO tAAVDS tAAVDH tAVDO OE# tWEA tOEH WE# tACC tACC tOE tACC tCE tAAVDS A/DQ15A/DQ0 tACC tOE tOEZ tAAVDH AH AL D tAAVDS tAAVDH AH AL tCR tCEZ tOEZ D tCEZ RDY July 30, 2012 S29VS_XS-R_00_08 S29VS/XS-R MirrorBit® Flash Family 63 Da t a Sh e e t ( A d va n ce In for ma t i on ) Figure 11.3 Asynchronous Read Followed By Write - AADM Interface CLK may be at VIL or VIH or Active CLK CE# tCAS tAVDP AVD# tAVDO tAAVDS tAAVDH tAAVDS tAAVDH OE# tCS tWEA tOEH tVLWH tWP tWPH tCH tWC WE# tACC tCE tACC tAAVDS tAAVDH A/DQ15A/DQ0 AH tOE tDH tOEZ AL D tDS AH AL tCEZ D tCR tCEZ RDY Figure 11.4 Asynchronous Write - AADM Interface CLK may be at VIL or VIH or Active CLK CE# OE# low with AVD# low signals the presence of Address-High. The Address-High cycle is optional. When the high part of address does not change only the Address-Low cycle is needed. OE# enables data output only after the Address-Low cycle in which AVD# is Low and OE# is High. OE# is ignored after OE# returns high between accesses until the next Address-Low is received. tCAS tAVDP tAVDP tAVDP AVD# tAAVDH tAAVDS OE# tWEA tCS tWPH tVLWH tWP tWC tCH WE# tAAVDH A/DQ15A/DQ0 tAAVDS Add-High tAAVDS tAAVDH Add-Low tCR tDS tDH Data tCEZ RDY 64 S29VS/XS-R MirrorBit® Flash Family S29VS_XS-R_00_08 July 30, 2012 Dat a S he e t ( Ad van ce I nfor m at i on ) Figure 11.5 Asynchronous Write Followed By Read - AADM Interface CLK may be at VIL or VIH or Active CLK CE# tCAS tAVDP AVD# tAAVDS tAAVDH tAVDO OE# tWEA tCS tWPH tVLWH tWP tOEH tWC tCH WE# tACC A/DQ15A/DQ0 tAAVDS tAAVDH AH tOE tDS AL tDH tOEZ tCEZ tACC D AH AL D tCR tCEZ RDY Figure 11.6 Asynchronous Write Followed By Write - AADM Interface CLK may be at VIL or VIH or Active CLK CE# tCAS tAVDP AVD# tAAVDS tAAVDH tAAVDS tAAVDH OE# tWEA tCH tVLWH tVLWH tWP tCS tWPH tWP tWC WE# tAAVDS tAAVDH A/DQ15A/DQ0 tAAVDS AH tDS tDH tAAVDH AL tDH D tDS AH tCR AL D tCEZ RDY July 30, 2012 S29VS_XS-R_00_08 S29VS/XS-R MirrorBit® Flash Family 65 Da t a Sh e e t ( A d va n ce In for ma t i on ) Figure 11.7 Synchronous Read Wrapped Burst Address Low Only - AADM Interface tIA CLK tCES CE# OE# low with AVD# low signals the presence of Address-High. The Address-High cycle is optional. When the high part of address does not change only the Address-Low cycle is needed. tAVDS tAVDP tAVDH Address-Low only cycle AVD# tAVDS OE# enables data output only after the Address-Low cycle in which AVD# is Low and OE# is High. OE# is ignored after OE# returns high between accesses until the next Address-Low is received. tAVDH OE# WE# tBACC tBDH tACS tACH A/DQ15 - A/DQ0 AH tBDH tOEZ tOEZ tOE tOE AL tBACC AL tRACC tCR tRACC tRACC tRACC tCEZ RDY(with data) tRACC tRACC tRACC RDY(before data) Figure 11.8 Synchronous Read Continuous Burst - AADM Interface tIA tIA CLK In continuous burst, wait states equal to the internal access time are inserted between the end of one cache line and the start of the next cache line tCES CE# tAVDS tAVDH tAVDP AVD# tAVDS tAVDH OE# WE# tBACC tACS tACH tBACC tBDH tOE tOEZ A/DQ15-A/DQ0 tRACC tCR tRACC tRACC tCEZ RDY(with data) tRACC tRACC tRACC RDY(before data) 66 S29VS/XS-R MirrorBit® Flash Family S29VS_XS-R_00_08 July 30, 2012 Dat a S he e t ( Ad van ce I nfor m at i on ) Figure 11.9 Synchronous Read Wrapped Burst - AADM Interface tIA CLK 15 initial access cycles setting shown. tIA measured from CLK rising edge during AVD# Low to CLK rising edge at beginning of first data out. tCES CE# tAVDS OE# low with AVD# low signals the presence of Address-High. The Address-High cycle is optional. When the high part of address does not change only the Address-Low cycle is needed. tAVDP tAVDH AVD# tAVDS OE# enables data output only after the Address-Low cycle in which AVD# is Low and OE# is High. OE# is ignored after OE# returns high between accesses until the next Address-Low is received. tAVDH OE# WE# tBACC tBDH tACS tACH A/DQ15-A/DQ0 AH tOEZ tOE AL tRACC tCR tRACC tCEZ RDY(with data) tRACC tCEZ RDY(before data) Figure 11.10 Synchronous Read Followed By Read Burst - AADM Interface tIA tIA CLK tCES CE# tAVDS tAVDP tAVDH AVD# tAVDS tAVDH OE# WE# tBACC tBDH tACS tACH A/DQ15 - A/DQ0 AH tOEZ ASIC_tCO tOE tOE AL tRACC tCR AH tRACC tRACC tOEZ tBACC AL tRACC tCEZ RDY(with data) tRACC tRACC tRACC RDY(before data) July 30, 2012 S29VS_XS-R_00_08 S29VS/XS-R MirrorBit® Flash Family 67 Da t a Sh e e t ( A d va n ce In for ma t i on ) Figure 11.11 Synchronous Read Followed By Write - AADM Interface tIA CLK tCES CE# tAVDP tAVDH tAVDS tAVDP AVD# OE# tOEH tWPH tVLWH tWC tWEA tWP tCH WE# tBACC tBDH tACS tDH A/DQ15-A/DQ0 tACH AH tOE tBACC tDS tOEZ AL AH tRACC tCR tRACC tRACC AL Write Data tRACC tCEZ RDY(with data) tRACC tRACC tRACC RDY(before data) Figure 11.12 Synchronous Write Followed By Read Burst - AADM Interface tIA CLK CE# tCAS tAVDH tAVDS tAVDP tCES AVD# OE# tVLWH tWPH tWEA tWP# tWC WE# A/DQ15-A/DQ0 tOEH Address-High Cycles Optional Address-High Cycles Optional tBACC tBDH tAAVDH tAAVDS AH AL tDH tDS Write Data tOEZ tOE AH tBACC AL tCR tRACC tRACC tCR tRACC tRACC tRACC tCEZ RDY(with data) RDY(before data) 68 S29VS/XS-R MirrorBit® Flash Family S29VS_XS-R_00_08 July 30, 2012 Dat a S he e t ( Ad van ce I nfor m at i on ) Figure 11.13 Synchronous Write Followed By Write - AADM Interface CLK CE# tCAS tAVDP AVD# tAAVDS tAAVDH tAAVDS tAAVDH OE# tWEA tWPH tVLWH tWP tCS tVLWH tWC tWC tWP tCH WE# A/DQ15A/DQ0 tAAVDS tAAVDH AH AL tCR tDH tAAVDS tAAVDH AH AL tDS Write Data tRACC tRACC tDS Write Data tRACC tDH tCEZ RDY July 30, 2012 S29VS_XS-R_00_08 S29VS/XS-R MirrorBit® Flash Family 69 Da t a Sh e e t ( A d va n ce In for ma t i on ) 12. Revision History Section Description Revision 01 (May 15, 2008) Initial release Revision 02 (August 1, 2008) DC Characteristics Changed some values in the CMOS Compatible table Device ID and Common Flash Memory Interface Address Map Changed some values in the ID/CFI Data table Memory Address Map Added memory address map Revision 03 (September 12, 2008) Physical Dimensions/Connection Diagrams Updated ball positions Revision 04 (March 10, 2009) Blank Check Command Functional in Asynchronous Read Mode only DC Characteristics Changed some ICCB values Global Added 108 MHz; removed 66 MHz Revision 05 (May 26, 2010) Global Modified document title Features Clarified some points Ordering Information and Valid Combinations Added Industrial Temperature range option Address/Data Interface Corrected typo Device Bus Operations Table Corrected A/DQ15-A/DQ0 column information for Asynchronous Read Asynchronous Read Clarified asynchronous read operation. S29XS-R AADM Access Clarified asynchronous AADM read access. S29VS-R ADM Access Standardized logic Low and High descriptions to VIL and VIH. Clarified wait states required by initial access and internal boundary crossings. S29XS-R AADM Access Standardized logic Low and High descriptions to VIL and VIH. Clarified wait states required by initial access and internal boundary crossings. Writing Commands/Command Sequences Clarified device behavior. Program/Erase Operations Removed redundant information. Sector Lock Range Command Clarified Sector Lock Range behavior Figure Synchronous Read Mode Added “ADM Interface” label Figure Asynchronous Mode Read Added “ADM Interface” label Figure Asynchronous Program Operation Timings Added “ADM Interface” label Figure Back-to-Back Read/Write Cycle Timings Added “ADM Interface” label Figure Latency with Boundary Crossing Corrected CR8 setting in Notes 1 and 2 Figure Latency with Boundary Crossing into Bank Performing Embedded Operation Corrected CR8 setting in Notes 1 and 2 Figures Asynchronous Read - AADM Interface to Asynchronous Write Followed By Write - AADM Interface Clarified CLK waveform behavior Figure Synchronous Write Followed By Read Burst - AADM Interface Corrected Figure title ADM Interface (S29VS256R and S29VS128R) Clarified traditional interface Table Wait State vs. Frequency Modified title and added note 70 S29VS/XS-R MirrorBit® Flash Family S29VS_XS-R_00_08 July 30, 2012 Dat a S he e t ( Ad van ce I nfor m at i on ) Section Table Address Latency for 10 -13 Wait States Description Added note Table Address Latency for 9 Wait States Added note Figure Synchronous Read Removed note 1 CLK Characterization Removed note 2 Erase and Programming Performance Corrected note 2 Revision 06 (July 22, 2010) DC Characteristics Changed ICC Read test conditions to OE#=H with relevant values Performance Characteristics Updated tables Erase and Programming Performance Changed typical programming times Revision 07 (November 18, 2010) Erase and Programming Performance ID/CFI Data Changed maximum chip erase times Corrected Data and Description for Word Offset 03h, 55h, 56h Corrected Data for Word Offset 1Dh, 1Eh, 52h Revision 08 (July 30, 2012) Command Definitions July 30, 2012 S29VS_XS-R_00_08 Corrected number of cycles for Write Buffer Load S29VS/XS-R MirrorBit® Flash Family 71 Da t a Sh e e t ( A d va n ce In for ma t i on ) Colophon The products described in this document are designed, developed and manufactured as contemplated for general use, including without limitation, ordinary industrial use, general office use, personal use, and household use, but are not designed, developed and manufactured as contemplated (1) for any use that includes fatal risks or dangers that, unless extremely high safety is secured, could have a serious effect to the public, and could lead directly to death, personal injury, severe physical damage or other loss (i.e., nuclear reaction control in nuclear facility, aircraft flight control, air traffic control, mass transport control, medical life support system, missile launch control in weapon system), or (2) for any use where chance of failure is intolerable (i.e., submersible repeater and artificial satellite). Please note that Spansion will not be liable to you and/or any third party for any claims or damages arising in connection with above-mentioned uses of the products. Any semiconductor devices have an inherent chance of failure. You must protect against injury, damage or loss from such failures by incorporating safety design measures into your facility and equipment such as redundancy, fire protection, and prevention of over-current levels and other abnormal operating conditions. If any products described in this document represent goods or technologies subject to certain restrictions on export under the Foreign Exchange and Foreign Trade Law of Japan, the US Export Administration Regulations or the applicable laws of any other country, the prior authorization by the respective government entity will be required for export of those products. Trademarks and Notice The contents of this document are subject to change without notice. This document may contain information on a Spansion product under development by Spansion. Spansion reserves the right to change or discontinue work on any product without notice. The information in this document is provided as is without warranty or guarantee of any kind as to its accuracy, completeness, operability, fitness for particular purpose, merchantability, non-infringement of third-party rights, or any other warranty, express, implied, or statutory. Spansion assumes no liability for any damages of any kind arising out of the use of the information in this document. Copyright © 2008-2012 Spansion Inc. All rights reserved. Spansion®, the Spansion logo, MirrorBit®, MirrorBit® Eclipse™, ORNAND™ and combinations thereof, are trademarks and registered trademarks of Spansion LLC in the United States and other countries. Other names used are for informational purposes only and may be trademarks of their respective owners. 72 S29VS/XS-R MirrorBit® Flash Family S29VS_XS-R_00_08 July 30, 2012
S29VS128RABBHW013 价格&库存

很抱歉,暂时无法提供与“S29VS128RABBHW013”相匹配的价格&库存,您可以联系我们找货

免费人工找货