TLE4294GV50HTSA1

OPTIREG™ linear TLE4294GV50 Low dropout voltage regulator Features • Output voltage tolerance ≤ ±4% • Very low drop out voltage • Output current: 30 mA • Low quiescent current consumption • Wide operating range up to 45 V • Wide temperature range: Tj = -40°C to +150°C • Output protected against short circuit • Overtemperature protection • Reverse polarity protection • Very small SMD package PG-SCT595-5 • Green Product (RoHS compliant) Potential applications General automotive applications. Product validation Qualified for automotive applications. Product validation according to AEC-Q100. Description The OPTIREG™ linear TLE4294GV50 is a monolithic integrated low drop out voltage regulator in a very small SMD package PG-SCT595-5. It is designed to supply e.g. microcontroller systems under severe conditions. Therefore the device is equipped with additional protection functions against overload, short circuit and reverse polarity. In case of an overtemperature condition the regulator is automatically turned off by the integrated thermal protection circuit. Input voltages up to 40 V are regulated to VQ,nom = 5.0 V. The output is able to drive a load of more than 30 mA, while it regulates the output voltage within a 4% accuracy. Type Package Marking TLE4294GV50 PG-SCT595-5 F1 Datasheet www.infineon.com/OPTIREG-linear 1 Rev. 1.2 2021-04-28 OPTIREG™ linear TLE4294GV50 Low dropout voltage regulator Table of contents Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Potential applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Product validation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Table of contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 1 Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 2.1 2.2 Pin configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Pin assignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Pin definitions and functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 3 3.1 3.2 3.3 General product characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Functional range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Thermal resistance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 4.1 Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Electrical characteristics voltage regulator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 5 Application information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 6 Package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 7 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Datasheet 2 5 5 6 6 Rev. 1.2 2021-04-28 OPTIREG™ linear TLE4294GV50 Low dropout voltage regulator Block diagram 1 Block diagram Saturation Control and Protection Circuit Temperature Control I 3 4 Band-Gap Reference Q + 2,5 GND Figure 1 Datasheet AEB02312a Block diagram 3 Rev. 1.2 2021-04-28 OPTIREG™ linear TLE4294GV50 Low dropout voltage regulator Pin configuration 2 Pin configuration 2.1 Pin assignment 5 1 4 2 3 SCT595.vsd Figure 2 Pin configuration (top view) 2.2 Pin definitions and functions Table 1 Pin definitions and functions Pin Symbol Function 1 N.C. Not connected Internally not connected. Connect to GND. 2 GND Ground Connected to pin 5. 3 I Input voltage For compensating line influences, a capacitor to GND close to the IC terminals is recommended. 4 Q Output voltage Block to GND with a capacitor close to the IC terminals, respecting the values given for its capacitance CQ and ESR in the Table 3 “Functional range” on Page 6 (Tantalum capacitor recommended as output capacitor). 5 GND Ground Connect to heatsink area; Connected to pin 2. Datasheet 4 Rev. 1.2 2021-04-28 OPTIREG™ linear TLE4294GV50 Low dropout voltage regulator General product characteristics 3 General product characteristics 3.1 Absolute maximum ratings Table 2 Absolute maximum ratings1) Tj = -40°C to +150°C; all voltages with respect to ground, direction of currents as shown in Figure 3 (unless otherwise specified) Parameter Symbol Values Min. Typ. Max. -42 45 Unit Note or Test Condition Number V – P_3.1.1 P_3.1.2 Input Voltage Current VI – II – – – mA 2) VQ -6 – 30 V – P_3.1.3 P_3.1.4 Output Voltage IQ – – – mA 2) Junction temperature Tj -40 – 150 °C – P_3.1.5 Storage temperature Tstg -50 – 150 °C – P_3.1.6 VESD -2 – 2 kV HBM3) P_3.1.7 4) P_3.1.8 Current Temperatures ESD susceptibility ESD resistivtiy ESD resistivity to GND 1) 2) 3) 4) VESD -750 – 750 V CDM Not subject to production test, specified by design. Internally limited. ESD susceptibility, Human Body Model “HBM” according to EIA/JESD 22-A114B. ESD susceptibility, Charged Device Model “CDM” according to EIA/JESD22-C101 or ESDA STM5.3.1. Notes 1. Stresses above the ones listed here may cause permanent damage to the device. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. 2. Integrated protection functions are designed to prevent IC destruction under fault conditions described in the data sheet. Fault conditions are considered as “outside” normal operating range. Protection functions are not designed for continuous repetitive operation. Datasheet 5 Rev. 1.2 2021-04-28 OPTIREG™ linear TLE4294GV50 Low dropout voltage regulator General product characteristics 3.2 Functional range Table 3 Functional range Parameter Symbol Values Min. Typ. Max. Unit Note or Test Condition Number – P_3.2.1 Inhibit voltage VI 5.5 – 45 V Output capacitor requirements CQ 2.2 – – µF – P_3.2.2 ESRCQ 1.5 – 8 Ω 1) P_3.2.3 Junction temperature Tj -40 – 150 °C – P_3.2.4 1) Equivalent series resistance measured at a frequency of 10 kHz. Note: Within the functional or operating range, the IC operates as described in the circuit description. The electrical characteristics are specified within the conditions given in the electrical characteristics table. 3.3 Thermal resistance Note: This thermal data was generated in accordance with JEDEC JESD51 standards. For more information, go to www.jedec.org. Table 4 Thermal resistance Parameter Junction to ambient Symbol 1) Junction to soldering point RthJA RthJSP Values Min. Typ. Max. – – 179 Unit Note or Test Condition Number Footprint only2) P_3.3.1 K/W 2 – 99 – K/W 300 mm heat sink area on PCB2) P_3.3.2 – 87 – K/W 600 mm2 heat sink area on PCB2) P_3.3.3 – 80 – K/W 2s2p PCB3) P_3.3.4 – 26 – K/W Measured to pin 5 P_3.3.5 1) Not subject to production test, specified by design. 2) EIA/JESD 52_2, FR4, 80 x 80 x1.5 mm; 35µ Cu, 5µ Sn. 3) Specified RthJA value is according to JEDEC JESD51-2,-5,-7 at natural convection on FR4 2s2p board. The product (chip + package) was simulated on a 76.2 x 114.3 x 1.5 mm board with 2 inner copper layers (2 x 70 µm Cu, 2 x 35µm Cu). Datasheet 6 Rev. 1.2 2021-04-28 OPTIREG™ linear TLE4294GV50 Low dropout voltage regulator Electrical characteristics 4 Electrical characteristics 4.1 Electrical characteristics Table 5 Electrical characteristics VI = 13.5 V; Tj = -40°C to +150°C; all voltages with respect to ground, direction of currents as shown in Figure 3 (unless otherwise specified) Parameter Symbol Values Unit Note or Test Condition Number Min. Typ. Max. Output Output voltage VQ 4.80 5.00 5.20 V 1 mA ≤ IQ < 30 mA; VI < 13.5 V P_4.1.1 Output voltage VQ 4.80 5.00 5.20 V IQ = 10 mA; 6 V < VI < 40 V P_4.1.2 Output current limitation IQ 30 – mA 1) P_4.1.3 Drop out voltage Vdr – 0.25 0.40 V IQ = 20 mA1) P_4.1.4 Current consumption Iq = II – IQ Iq – 2 4 mA IQ < 30 mA P_4.1.5 Current consumption Iq = II – IQ Iq – 120 200 µA IQ < 1 mA P_4.1.6 Load regulation |∆VQ| – 10 25 mV 1 mA < IQ < 25 mA; Tj = 25°C; P_4.1.7 Load regulation |∆VQ| – 10 30 mV 1 mA < IQ < 25 mA; P_4.1.8 Line regulation |∆VQ| – 5 25 mV ∆VI = VI,min to 36 V; IQ = 5 mA; Tj = 25°C P_4.1.9 Line regulation |∆VQ| – 10 30 mV ∆VI = VI,min to 36 V; IQ = 5 mA; P_4.1.10 Power supply ripple rejection PSRR – 60 – dB fr = 100 Hz; Vr = 0.5 Vpp P_4.1.11 – Current consumption Regulator performance 1) Measured when the output voltage VQ has dropped 100 mV from the nominal value. Datasheet 7 Rev. 1.2 2021-04-28 OPTIREG™ linear TLE4294GV50 Low dropout voltage regulator Application information 5 Application information Note: The following information is given as a hint for the implementation of the device only and shall not be regarded as a description or warranty of a certain functionality, condition or quality of the device. Supply II I Q 3 TLE4294 4 Regulated Output Voltage IQ Load e. g. Micro Controller C CI ESR Application_Circuit.vsd } CQ GND 2, 5 GND Iq Figure 3 Datasheet Application diagram 8 Rev. 1.2 2021-04-28 OPTIREG™ linear TLE4294GV50 Low dropout voltage regulator Package information 6 Package information 2.9 ±0.2 B (2.2) 1.2 +0.1 -0.05 1.1 max (0.3) 10˚max 1.6 ±0.1 10˚max 1) +0.2 acc. to DIN 6784 2.6 max 0.25 min 0.1 max (0.23) (0.13) (0.4) 1) 0.3 +0.1 -0.05 0.15 +0.1 -0.06 0.6 +0.1 -0.05 0.20 0.95 1.9 0.25 Figure 4 M B 1) M A A Contour of slot depends on profile of gull-wing lead form PG-SCT595-51) Green Product (RoHS compliant) To meet the world-wide customer requirements for environmentally friendly products and to be compliant with government regulations the device is available as a green product. Green products are RoHS-compliant (i.e. Pb-free finish on leads and suitable for Pb-free soldering according to IPC/JEDEC J-STD-020). Further information on packages https://www.infineon.com/packages 1) Dimensions in mm Datasheet 9 Rev. 1.2 2021-04-28 OPTIREG™ linear TLE4294GV50 Low dropout voltage regulator Revision history 7 Revision history Revision Date Changes 1.2 2021-04-28 Updated layout and structure Editorial changes added TOC 1.1 2008-02-26 Device marking changed to F1 1.0 2004-01-01 Initial release Datasheet 10 Rev. 1.2 2021-04-28 Trademarks All referenced product or service names and trademarks are the property of their respective owners. Edition 2021-04-28 Published by Infineon Technologies AG 81726 Munich, Germany © 2004 Infineon Technologies AG. All Rights Reserved. Do you have a question about any aspect of this document? Email: erratum@infineon.com Document reference Z8F55216950 IMPORTANT NOTICE The information given in this document shall in no event be regarded as a guarantee of conditions or characteristics ("Beschaffenheitsgarantie"). With respect to any examples, hints or any typical values stated herein and/or any information regarding the application of the product, Infineon Technologies hereby disclaims any and all warranties and liabilities of any kind, including without limitation warranties of non-infringement of intellectual property rights of any third party. In addition, any information given in this document is subject to customer's compliance with its obligations stated in this document and any applicable legal requirements, norms and standards concerning customer's products and any use of the product of Infineon Technologies in customer's applications. The data contained in this document is exclusively intended for technically trained staff. It is the responsibility of customer's technical departments to evaluate the suitability of the product for the intended application and the completeness of the product information given in this document with respect to such application. For further information on technology, delivery terms and conditions and prices, please contact the nearest Infineon Technologies Office (www.infineon.com). WARNINGS Due to technical requirements products may contain dangerous substances. For information on the types in question please contact your nearest Infineon Technologies office. Except as otherwise explicitly approved by Infineon Technologies in a written document signed by authorized representatives of Infineon Technologies, Infineon Technologies’ products may not be used in any applications where a failure of the product or any consequences of the use thereof can reasonably be expected to result in personal injury.