TLE4959C FX Flexible Transmission Speed
Sensor
Features
•
Hall based differential speed sensor
•
High magnetic sensitivity
•
Large operating airgap
•
Dynamic self-calibration principle
•
Adaptive hysteresis
•
Output protocols with and without direction of rotation detection
•
High vibration suppression capabilities
•
Three wire voltage interface
•
Magnetic encoder and ferromagnetic wheel application
•
High immunity against ESD, EMC and mechanical stress, improved voltage dropout capability
•
Automotive operating temperature range
•
End-of-line programmable to adjust transmission requirements.
•
Green Product (RoHS compliant)
•
AEC Qualified
Applications
The TLE4959C FX is an integrated differential Hall speed sensor ideally suited for transmission applications. Its
basic function is to provide information about rotational speed and direction of rotation to the transmission
control unit. TLE4959C FX includes a sophisticated algorithm which actively suppresses vibration while
keeping excellent airgap performance.
Table 1
Description
Type
Marking
Ordering Code
Package
TLE4959C FX
59AIC1
SP001040492
PG-SSO-3-52
Data Sheet
www.infineon.com/sensors
1
1.0
2018-02
TLE4959C FX Flexible Transmission Speed Sensor
Description
The TLE4959C FX comes in a RoHs compliant three-pin package, qualified for automotive usage. It has two
integrated capacitors on the lead frame (220 nF/1.8 nF). These capacitors increase the EMC robustness of the
device. In 12 V applications it is further recommended to use a serial resistor RSupply of 100 Ω (tbd) for
protection on the supply line. A pull-up resistor RLoad is mandatory on the output pin and determines the
maximum current flowing through the output transistor. A value of 1.2 kΩ is recommended for the 5V
application. (see Figure 1)
IDD
Option for 12 V
Vpullup
PG-SSO- 3-52
VDD
RSupply
CV DD
CV DD = 220 nF
CQ = 1.8 nF
...integrated in package
Figure 1
Data Sheet
V DD
IQ
Q
GND
R Load
1.2 kΩ
CQ
VQ
Typical Application Circuit
2
1.0
2018-02
TLE4959C FX Flexible Transmission Speed Sensor
Functional Description
1
Functional Description
The differential Hall sensor IC detects the motion of tooth and magnet encoder applications. To detect the
motion of ferromagnetic objects, the magnetic field must be provided by a back biasing permanent magnet.
Either south or north pole of the magnet can be attached to the rear unmarked side of the IC package (See
Figure 2). The magnetic measurement is based on three equally spaced Hall elements, integrated on the IC.
Both magnetic and mechanical offsets are cancelled by a self calibration algorithm.
1.1
Definition of the Magnetic Field Direction
The magnetic field of a permanent magnet exits from the north pole and enters the south pole. If a north pole
is attached to the backside of the High End Transmission Sensor, the field at the sensor position is positive, as
shown in Figure 2.
Notch
Tooth
Notch
Notch
Tooth
Notch
IC Branded
Side
S
Figure 2
1.2
S
N
N
IC Branded
Side
Definition of the Positive Magnetic Field Direction
Block Diagram
VDD
PMU:
Chopper switches
Separated supplies
Bandgap (Temp. Compensated)
GND
Digital-Core:
Figure 3
Data Sheet
Diff. Hall
Speed-sensing
Compensated
Amplifier and
Tracking ADC
Hall
Directionsensing
Compensated
Amplifier and
Tracking ADC
Min/Max -detection
Offset-calculation
Hysteresis-calculation
Offset compensation
Direction detection
Vibration suppression
Output-protocol
Open
Drain
Q
EEPROM
Block Diagram
3
1.0
2018-02
TLE4959C FX Flexible Transmission Speed Sensor
Functional Description
1.3
Basic Operation
The speed signal calculated out of the differential hall elements, is amplified, filtered and digitized. An
algorithm in the digital core for peak detection and offset calculation will be executed. The offset is fed back
into the speed signal path with a digital to analog converter for offset correction. During uncalibrated mode,
the output of the speed pulse is triggered in the digital core by exceeding a certain threshold of the tracking
ADC. In calibrated mode the output is triggered by the visible hysteresis.
The direction signal is calculated out of center Hall signals. The direction signal is amplified, filtered, and
digitized. In the digital core the direction and the vibration detection information is determined and the
output protocol is issued.
1.4
Uncalibrated and Calibrated Mode
After power on the differential magnetic speed signal is tracked by an analog to digital converter (Tracking
ADC) and monitored within the digital core. If the signal slope is identified as a rising edge or falling edge, the
first output pulse is triggered. A second trigger pulse is issued with direction information.
In uncalibrated mode, the output protocols are triggered by the DNC (detection noise constant) in the speed
path. After start up the sensor switches with the DNC min value and after that the DNC is adapted to the
magnetic input signal amplitude.
The offset update starts if two valid extrema values are found and the direction of the update has the same
orientation as the magnetic signal. For example, a positive offset update is being issued on a rising magnetic
edge only. After a successful offset correction, the sensor is in calibrated mode. Switching occurs at the
adaptive hysteresis threshold level.
In calibrated mode, the DNC is adapted to magnetic input signal amplitude with a minimum of
ΔBlimit . The output pulses are then triggered with adaptive hysteresis.
1.5
Hysteresis Concept
The adaptive hysteresis is linked to the input signal. Therefore, the system is able to suppress switching if
vibration or noise signals are smaller than the adaptive hysteresis levels. The minimum hysteresis level is
ΔBlimit.
The visible hysteresis keeps the excellent performance in large pitch transmission application wheels.
Hysteresis = 0.25 * ΔBpp (peak to peak )
10
8
magnetic input signal
hysteresis HI
hysteresis LO
ΔBz,diff
6
ΔBpp [mT]
4
2
0
-2
-4
-6
-8
-10
0
0.01
0.02
0.03
0.04
0.05
0.06
0.07
time [s]
Figure 4
Data Sheet
Adaptive Hysteresis
4
1.0
2018-02
TLE4959C FX Flexible Transmission Speed Sensor
Functional Description
1.6
Rotational Direction
The direction signal is digitized by an analog to digital converter (direction ADC) and fed into the digital core.
Depending upon the rotation direction of the target wheel, the signal of the center probe anticipates or lags
behind for 90°. This phase relationship is evaluated and converted into rotation direction information by
sampling the signal of the center probe in the proximity of the zero crossing of the “speed” bridge signal.
The first pulse after power (power on pulse) has a different length to signalize that there is no direction
information available .
Forward pulse (tfwd) is issue if the wheel rotates from pin 1 to pin 3
Backward pulse (tbwd) is issue if the wheel rotates from pin 3 to pin 1
Forward/backward pulse length could be inverted via EEPROM settings.
Branded
side
speed
signal
B z,left – B z,right
B z,left
B z,right
N
S
123
Figure 5
Monocell
direction
signal
B z,center
Direction definition
In case of high speed has been enable, the direction detection is switched off as soon as the frequency reach
4.3 kHz. To enter or leave the high frequency, two consecutive periods have to be larger or smaller than the
frequency limit. this may delay the high frequency pulse at power on.
1.7
Vibration Suppression
The magnetic signal amplitude and the direction information are used for detection of parasitic magnetic
signals. Unwanted magnetic signal can be caused by angular or air gap vibrations. If an input signal is
identified as a vibration the output pulse will be suppressed.
Data Sheet
5
1.0
2018-02
TLE4959C FX Flexible Transmission Speed Sensor
General Characteristics
2
General Characteristics
2.1
Absolute Maximum Ratings
Table 2
Absolute Maximum Ratings
Parameter
Symbol
Supply voltage without
supply resistor
VDD
Values
Output ON voltage
VQ_OFF
VQ_ON
Note or Test Condition
Min.
Typ.
Max.
-16
–
18
V
continuous, TJ ≤ 175°C
27
V
max. 60 s, TJ ≤ 175°C
V
max. 60 s, TJ ≤ 175°C
V
max. 1 h,TAmb ≤ 40°C
-18
Output OFF voltage
Unit
-1.0
–
-0.3
–
26.5
V
continuous, TJ ≤ 175°C
–
–
16
V
continuous, TAmb ≤ 40°C
–
–
18
V
max. 1 h, TAmb ≤ 40°C
–
–
26.5
V
max. 60 s, TAmb ≤ 40°C
Junction temperature
range
TJ
-40
–
185
°C
exposure time: max. 10 × 1 h, VDD = 16V
Magnetic field induction
BZ
-5
–
5
T
magnetic pulse during magnet
magnetization
valid 10 s with Tambient ≤ 80°C
ESD compliance
ESDHBM
-6
–
6
kV
HBM1)
1) ESD susceptibility, HBM according to EIA/JESD 22-A114B
Note:
Data Sheet
Stresses above the max values listed here may cause permanent damage to the device. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability. Maximum
ratings are absolute ratings; exceeding only one of these values may cause irreversible damage to
the integrated circuit.
6
1.0
2018-02
TLE4959C FX Flexible Transmission Speed Sensor
General Characteristics
2.2
Operating Range
All parameters specified in the following sections refer to these operating conditions unless otherwise
specified.
Table 3
General Operating Conditions
Parameter
Symbol
Values
Unit Note or Test Condition
Min.
Typ.
Max.
Supply voltage without supply
resistance Rs
VDD
4.0
–
16
V
Continuous Output Off voltage
VQ_OFF
-
–
16
V
Supply voltage power- up/down
voltage ramp
dVDD/dt
3.0
–
1e4
V/ms
Supply current
IDD
8.0
–
13.4
mA
Continuous output On current
IQ_ON
–
15
mA
VQ_LOW < 0.5 V
Capacitance between IC supply &
ground pins
CVDD
198
220
242
nF
capacitor type X8R,
rated voltage =50 V1)
Output capacitance between IC
output and ground pins
CQ
1.62
1.8
1.98
nF
capacitor type X8R,
rated voltage =50 V1)
Magnetic signal frequency range
f
0
–
10
kHz
Frequency range for direction
detection (hystersis)once high
speed has been selected
fDir
0
–
4.3
kHz
increasing rotational
frequency
0
–
4
kHz
decreasing rotational
frequency
Maximum number of EEPROM
programming cycles
NPROG
100
n
–
120
mT
–
60
mT
–
550
mT
–
450
mT
Dynamic range of the magnetic field DRmag_field_s
of the differential speed channel
-120
Dynamic range of the magnetic field DRmag_field_dir -60
of the direction channel
Static range of the magnetic field of SRmag_field_s
the outer Hall probes in back-bias
configuration
0
Static range of the magnetic field of DRmag_field_dir -100
the center Hall probe
Allowed static difference between
outer probes
SRmag_field_diff -30
–
30
mT
Normal operating junction
temperature
TJ
-40
–
175
°C
exposure time: max. 2500 h
at TJ = 175°C, VDD = 16 V
–
–
185
°C
exposure time: max.
10 × 1 h at TJ = 185°C,
VDD = 16 V, additive to other
lifetime
Data Sheet
7
1.0
2018-02
TLE4959C FX Flexible Transmission Speed Sensor
General Characteristics
Table 3
General Operating Conditions (cont’d)
Parameter
Symbol
Values
Min.
Not operational lifetime
Tno
-40
Ambient temperature range for
device features reading and
programming
TRDPROG
15
Temperature compensation range
of magnetic material
TC
Typ.
25
-600
Unit Note or Test Condition
Max.
150
°C
without sensor function.
Exposure time max 500 h @
150°C; increased time for
lower temperatures
according to ArrheniusModel, additive to other
lifetime
130
°C
during programming at
customer
ppm internal compensation of
magnetic signal amplitude
of speed signal
1) Specified at room temperature, test condition at 25°C with 1V at 1kHz, temperature variation to be added
Note:
Data Sheet
In the operating range the functions given in the functional description are fulfilled
8
1.0
2018-02
TLE4959C FX Flexible Transmission Speed Sensor
Electrical and Magnetic Characteristics
3
Electrical and Magnetic Characteristics
All values specified at constant amplitude and offset of input signal, over operating range, unless otherwise
specified. Typical values correspond to VS = 5 V and TAmb. = 25°C
Table 4
Electrical and Magnetic Parameters
Parameter
Symbol
Values
Unit
Note or Test Condition
Min.
Typ.
Max.
–
500
mV
IQ ≤ 15 mA
Output saturation voltage
VQsat
0
Clamping voltage VDD-Pin
VDD_clamp
42
–
V
leakage current through ESD
diode < 0.5mA
Clamping voltage VQ-Pin
VQclamp
42
–
V
leakage current through ESD
diode < 0.5mA
Reset voltage
VDD_reset
2.8
3.6
V
Output leakage current
IQleak
0
0.1
10
µA
Output current limit during
short-circuit condition
IQshort
30
–
80
mA
Junction temperature limit for
output protection
Tprot
190
–
205
°C
Power on time
tpower_on
0.8
0.9
1
ms
during this time the output is
locked to high.
Delay time between magnetic
signal switching point and
corresponding output signal
falling edge switching event
tdelay
10
14
19
µs
falling edge
Output fall time
tfall
2.0
2.5
3.0
µs
VPullup = 5 V, RPullup = 1.2 kΩ (+/10%), CQ = 1.8 nF (+/-15%),
valid between 80% - 20%
3.2
4.5
5.8
µs
VPullup = 5 V, RPullup = 1.2 kΩ (+/10%), CQ = 1.8 nF (+/-15%),
valid between 90% - 10%
4
–
11.4
µs
RPullup = 1.2 kΩ (+/-10%),
CQ = 1.8 nF (+/-15%),
valid between 10% - 90%
Digital noise constant of speed DNCmin
channel during start up
1.22
1.5
1.78
mT
Adaptive hysteresis threshold
–
25
–
%
EEPROM
“HYST_ADAPT”Option 0
–
12.5
–
%
EEPROM
“HYST_ADAPT”Option 1
Jit8kHz
-1
–
1
%
1 sigma, ΔBpkpk = 3mT
Jit10kHz
-1.1
1.1
%
1 sigma, ΔBpkpk = 3mT
nStart
–
–
0
n
in forward rotational direction
0
–
1
n
in backward rotational
direction
trise1)
Output rise time
HYSadaptive
Period Jitter, f ≤ 8 kHz 2)
Period Jitter, 8kHz ≤ f ≤ 10kHz
Number of wrong pulses at
start-up
Data Sheet
2)
9
VQ = 18 V
1.0
2018-02
TLE4959C FX Flexible Transmission Speed Sensor
Electrical and Magnetic Characteristics
Table 4
Electrical and Magnetic Parameters (cont’d)
Parameter
Symbol
Values
Min.
Unit
Note or Test Condition
Typ.
Max.
–
40
%
of magnetic speed signal
amplitude
0
–
60
%
of magnetic speed signal
amplitude with reduced
performance on stand-still
functionality
Runoutglob 0
–
40
%
of magnetic direction signal
amplitude
0
–
60
%
Of magnetic direction signal
amplitude with reduced
performance on stand-still
functionality
Tooth to tooth run out (peak to Runouttooth 0
peak variation on two
,speed
consecutive teeth / pole-pair)3) Runout
tooth 0
–
40
%
of magnetic speed signal
amplitude
–
40
%
of magnetic direction signal
amplitude
3)
Global run out
Runoutglob 0
al,speed
al,dir
,dir
1) Value of capacitor: 1.8 nF±10%; ceramic: X8R; maximum voltage: 50 V
2) Parameter not subject to productive test. Verified by lab characterization based on jitter-measurement > 1000
periods
3) Defined as 1-(amplitude_min/amplitude_max)
Note:
The listed Electrical and magnetic characteristics are ensured over the operating range of the
integrated circuit. Typical characteristics specify mean values expected over the production spread.
If not other specified, typical characteristics apply at TAmb = 25°C and VS = 5 V.
3.1
Output protocols
TLE4959C FX provides the option to select output protocol without direction detection. As well as the
following direction detection options where the direction is provided via PWM protocol.
Table 5
Option 1
Parameter
Symbol
Values
Unit
Min.
Typ.
Max.
Output pulse in forward
direction
tfwd
38
45
52
µs
Output pulse in backward
direction
tbwd
114
135
155
µs
Power on pulse
tpower-on
153
180
207
µs
Data Sheet
10
Note or Test Condition
1.0
2018-02
TLE4959C FX Flexible Transmission Speed Sensor
Electrical and Magnetic Characteristics
Table 5
Option 1 (cont’d)
Parameter
Symbol
Values
Min.
Typ.
Max.
Unit
Note or Test Condition
Output pulse at High speed
thigh_speed
25.5
30
34.5
µs
pulse available after High
speed option has been
selected
Stand still pulse
tstand-still
51
60
69
µs
pulse available stand still after
pulse option has been
selected. Pulse delivered if no
relevant magnetic signal
change has been detected
within 50ms
Note:
Table 6
VPullup = 5 V, RPullup = 1.2 kΩ (+/-10%), CQ = 1.8 nF (+/-15%), valid between 50% of falling edge to
50% of next rising edge
Option 2
Parameter
Symbol
Values
Unit
Min.
Typ.
Max.
Output pulse in forward
direction
tfwd
38
45
52
µs
Output pulse in backward
direction
tbwd
153
180
207
µs
Output pulse at High speed
thigh_speed
38
45
52
µs
Note or Test Condition
pulse available after High
speed option has been
selected
Attention: First pulse after magnetic edge suppressed
Note:
Table 7
VPullup = 5 V, RPullup = 1.2 kΩ (+/-10%), CQ = 1.8 nF (+/-15%), valid between 50% of falling edge to
50% of next rising edge
Option 3
Parameter
Symbol
Values
Unit
Min.
Typ.
Max.
Output pulse in forward
direction
tfwd
51
60
69
µs
Output pulse in backward
direction
tbwd
102
120
138
µs
Power on pulse
tpower-on
25.5
30
34.5
µs
Output pulse at High speed
thigh_speed
25.5
30
34.5
µs
Data Sheet
11
Note or Test Condition
pulse available after High
speed option has been
selected
1.0
2018-02
TLE4959C FX Flexible Transmission Speed Sensor
Electrical and Magnetic Characteristics
Note:
Table 8
VPullup = 5 V, RPullup = 1.2 kΩ (+/-10%), CQ = 1.8 nF (+/-15%), valid between 50% of falling edge to
50% of next rising edge
Option 4
Parameter
Symbol
Values
Unit
Min.
Typ.
Max.
Output pulse in forward
direction
tfwd
38
45
52
Output pulse in backward
direction
tbwd
76.5
90
103.5 µs
Power on pulse
tpower-on
153
180
207
µs
Output pulse at High speed
thigh_speed
38
45
52
µs
Note:
Data Sheet
Note or Test Condition
µs
pulse available after High
speed option has been
selected
VPullup = 5 V, RPullup = 1.2 kΩ (+/-10%), CQ = 1.8 nF (+/-15%), valid between 50% of falling edge to
50% of next rising edge
12
1.0
2018-02
TLE4959C FX Flexible Transmission Speed Sensor
EEPROM Functional Description
4
EEPROM Functional Description
4.1
Serial Interface
The serial interface is used to set parameter and to program the sensor IC, it allows writing and reading of
internal registers. Data transmission to the IC is done by supply voltage modulation, by providing the clock
timing and data information via only one line. Data from the IC are delivered via the output line, triggered by
as well clocking the supply line. In normal application operation the interface is not active, for entering that
mode a certain command right after power-on is required.
A detailed document (TLE4959C FX EEPROM Programming Guide) is available on request. It contains the
description of electrical timing and voltage requirements, as well as the information about data protocol,
available registers and addresses.
4.1.1
Data Transmission
Commands to the sensor are sent by modulating the supply voltage between two levels VDD,high and VDD,low.
They are sent in series of 17 pulses corresponding to 16 bit words, with MSB transmitted first and LSB last,
respectively the stop bit. Each of the 16 pulses is coded by the duty cycle as logical “0” or “1”. Logical "1" is
represented by a duty cycle of 2/3 of the period on VDD,high, logical “0” is represented by a duty cycle of 1/3 at
VDD,high. This forms the bit information and acts also as serial interface clock. Data transmission from the device
is represented by the state of the output, high for logical “1” and low for logical “0”. Recommended period
length is around 200 (tbd) µs per bit.
End of word is indicated by a long "low" supply (> 750 ms, first 30 ms should be > VDD,high, remaining time
< VDD,low). Please note, that for transmission of 16 data bits in total 17 pulses on VDD are necessary. If more than
16 input bits are transmitted the output bits are irrelevant (transmission buffer empty), whereas the input bits
remain valid and start overwriting the previously transmitted bits. In any case the last 17 transmitted bits are
interpreted as transmitted data word (16 bit) + 1 stop bit.
tON
VDD
t dig_reset
tSupply ,enter
0 0 0 0 1 0 0
MSB
tbit t bit tbit tbit tbit t bit
thigh t low
1
1
0
1
1
1 0
LSB Stop_bit=0
tSupplyhigh,exit
t stop
VDD,high
VDD,low
pulse1……
pulse17
0
time
VQ
Figure 6
Data Sheet
MSB
LSB
Serial Protocol
13
1.0
2018-02
TLE4959C FX Flexible Transmission Speed Sensor
EEPROM Functional Description
4.2
EEPROM Description
Several options of TLE4959C FX can be programmed via an EEPROM to optimize the sensor algorithm to the
individual target wheel and application requirements. The EEPROM memory is organized in 2 customer lines.
Each line is composed of 16 data bits and additional 6 bits for error detection and correction, based on ECC
(Error Correction Code). For more detailed information about EEPROM access and programming an additional
document is available on request.
Table 9
15
EEPROM Address 0x0
14
Table 10
13
12
11
10
9
8
7
6
5
4
3
2
1
Functional Description Address 0x0
Field
Bit
Type Description
TLE4959C FX
Not used
15
r
Always read as “0”
0
Not used
14
rw
To be set to “0”
0
HIGH_SPEED
13
rw
0 = Enabled motion detection
0
1 = According selected protocol when above
4.3kHz
Not used
12
rw
To be set to “0”
STAND_EN
11
rw
0=disable stand-still pulse
0
1=enable stand-still pulse
Stand still pulse is provided, if enabled, only
if PW_CHIOICE=00
Not used
10..0 rw
Table 11
EEPROM Address 0x1
15
14
Table 12
13
12
11
10
0
To be set to “00000000000”
9
8
7
6
00000000000
5
4
3
2
1
0
Functional Description Address 0x1
Field
Bit
Not used
15:14 rw
To be set to “01”
01
PW_CHOICE
13:12 rw
Choice of PWM protocol for direction
detection.
00 = Option 1
01 = Option 2
10 = Option 3
11 = Option 4
11
FORWARD_DEF
11
rw
0 = None invertion of forward definition
1 = Invertion of forward definition
0
EDGE_POLAR
10
rw
0 = None invertion
1 = Invertion
0
HYST_ADAPT
9
rw
0 = 25%
1 = 12.5%
1
Data Sheet
0
Type Description
TLE4959C FX
14
1.0
2018-02
TLE4959C FX Flexible Transmission Speed Sensor
EEPROM Functional Description
Table 12
Functional Description Address 0x1 (cont’d)
Field
Bit
Type Description
TLE4959C FX
Not used
8.. 5
rw
To be set to “1101”
1101
DNC_ADAPT
4
rw
DNC Adaption:
0 = 25%
1 = 12.5%
0
Not used
3
rw
To be set to “0”
0
DIR_ENABLE
2
rw
0 = Direction detection off
1 = Direction detection on
1
Not used
1
rw
To be set to “1”
1
LOCK
0
rw
0 = User area of EEPROM is unlocked
1 = User area of EEPROM is locked (no
reprogramming possible)
0
Data Sheet
15
1.0
2018-02
TLE4959C FX Flexible Transmission Speed Sensor
Package Information
5
Package Information
Pure tin covering (green lead plating) is used. The product is RoHS (Restriction of Hazardous Substances)
compliant and marked with letter G in front of the data code marking and may contain a data matrix code on
the rear side of the package (see also information note 136/03). Please refer to your key account team or
regional sales if you need further information.
The specification for soldering and welding is defined in the latest revision of application note
“Recommendation for Board Assembly-Hallsensor SSO Packages”.
5.1
Figure 7
Data Sheet
Package Outline
PG-SSO-3-52 (Plastic Green Single Slim Outline), Package Dimensions
16
1.0
2018-02
TLE4959C FX Flexible Transmission Speed Sensor
Package Information
5.2
Figure 8
5.3
Figure 9
5.4
Table 13
Position of the Hall Element
Position of the Hall Elements in PG-SSO-3-52 and Distance to the Branded Side
Marking and Data Matrix Code
Marking of PG-SSO-3-52 Package
Pin Configuration and Sensitive Area
Pin Description
Pin Number1)
Symbol
Function
1
VDD
Supply Voltage
2
GND
Ground
3
Q
Open Drain Output
1) Refer to frontside view: leftmost pin corresponding to pin number 1
Data Sheet
17
1.0
2018-02
TLE4959C FX Flexible Transmission Speed Sensor
Package Information
5.5
Figure 10
Data Sheet
Packing Information
PG-SSO-3-52 Ammopack
18
1.0
2018-02
TLE4959C FX Flexible Transmission Speed Sensor
Revision History
6
Revision History
Revision Date
Changes
1.0
First version of released datasheet
Data Sheet
2017-10-05
19
1.0
2018-02
Please read the Important Notice and Warnings at the end of this document
Trademarks of Infineon Technologies AG
µHVIC™, µIPM™, µPFC™, AU-ConvertIR™, AURIX™, C166™, CanPAK™, CIPOS™, CIPURSE™, CoolDP™, CoolGaN™, COOLiR™, CoolMOS™, CoolSET™, CoolSiC™,
DAVE™, DI-POL™, DirectFET™, DrBlade™, EasyPIM™, EconoBRIDGE™, EconoDUAL™, EconoPACK™, EconoPIM™, EiceDRIVER™, eupec™, FCOS™, GaNpowIR™,
HEXFET™, HITFET™, HybridPACK™, iMOTION™, IRAM™, ISOFACE™, IsoPACK™, LEDrivIR™, LITIX™, MIPAQ™, ModSTACK™, my-d™, NovalithIC™, OPTIGA™,
OptiMOS™, ORIGA™, PowIRaudio™, PowIRStage™, PrimePACK™, PrimeSTACK™, PROFET™, PRO-SIL™, RASIC™, REAL3™, SmartLEWIS™, SOLID FLASH™,
SPOC™, StrongIRFET™, SupIRBuck™, TEMPFET™, TRENCHSTOP™, TriCore™, UHVIC™, XHP™, XMC™.
Trademarks updated November 2015
Other Trademarks
All referenced product or service names and trademarks are the property of their respective owners.
Edition 2018-02
Published by
Infineon Technologies AG
81726 Munich, Germany
© 2018 Infineon Technologies AG.
All Rights Reserved.
Do you have a question about any
aspect of this document?
Email: erratum@infineon.com
IMPORTANT NOTICE
The information given in this document shall in no
event be regarded as a guarantee of conditions or
characteristics ("Beschaffenheitsgarantie").
With respect to any examples, hints or any typical
values stated herein and/or any information regarding
the application of the product, Infineon Technologies
hereby disclaims any and all warranties and liabilities
of any kind, including without limitation warranties of
non-infringement of intellectual property rights of any
third party.
In addition, any information given in this document is
subject to customer's compliance with its obligations
stated in this document and any applicable legal
requirements, norms and standards concerning
customer's products and any use of the product of
Infineon Technologies in customer's applications.
The data contained in this document is exclusively
intended for technically trained staff. It is the
responsibility of customer's technical departments to
evaluate the suitability of the product for the intended
application and the completeness of the product
information given in this document with respect to
such application.
For further information on technology, delivery terms
and conditions and prices, please contact the nearest
Infineon Technologies Office (www.infineon.com).
WARNINGS
Due to technical requirements products may contain
dangerous substances. For information on the types
in question please contact your nearest Infineon
Technologies office.
Except as otherwise explicitly approved by Infineon
Technologies in a written document signed by
authorized representatives of Infineon Technologies,
Infineon Technologies’ products may not be used in
any applications where a failure of the product or any
consequences of the use thereof can reasonably be
expected to result in personal injury.
