TLE7250GVIOXUMA1

TLE7250GVIO High Speed CAN Transceiver Data Sheet Rev. 1.1, 2014-05-07 Automotive Power TLE7250GVIO Table of Contents 1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 3 3.1 3.2 Pin Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Pin Assignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Pin Definitions and Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 4 4.1 4.2 4.3 4.4 4.5 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . High Speed CAN Physical Layer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Modes of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Normal-operating Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Stand-by Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Power-down State . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 5.1 5.2 5.3 5.4 5.5 Fail-safe Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Short-circuit Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Unconnected Logic Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TxD Time-out Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Undervoltage Detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Overtemperature Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 10 10 10 10 12 6 6.1 6.2 6.3 General Product Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Functional Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Thermal Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 13 14 14 7 7.1 7.2 Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Functional Device Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 8 8.1 8.2 8.3 Application Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ESD Immunity According to IEC61000-4-2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Application Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Further Application Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Package Outlines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 10 Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Data Sheet 2 6 6 8 9 9 9 19 19 20 20 Rev. 1.1, 2014-05-07 High Speed CAN Transceiver 1 TLE7250GVIO Overview Features • • • • • • • • • • • • • • • Fully compliant with ISO 11898-2 Wide common mode range for electromagnetic immunity (EMI) Very low electromagnetic emission (EME) Excellent ESD immunity Extended supply range at VCC and VIO Suitable for 5V and 3.3V microcontroller I/O voltages CAN short-circuit proof to ground, battery and VCC TxD time-out function Low CAN bus leakage current in power-down state Overtemperature protection Protected against automotive transients CAN data transmission rate up to 1 Mbps VIO input for voltage adaptation to the micro controller supply Green Product (RoHS-compliant) AEC Qualified PG-DSO-8 Description The TLE7250GVIO is a transceiver designed for CAN networks in automotive and industrial applications. As an interface between the physical bus layer and the CAN protocol controller, the TLE7250GVIO drives the signals to the bus and protects the microcontroller against interferences generated within the network. Based on the high symmetry of the CANH and CANL signals, the TLE7250GVIO provides a very low level of electromagnetic emission (EME) within a wide frequency range. The TLE7250GVIO is integrated in a RoHS-compliant PG-DSO-8 package and fulfills or exceeds the requirements of ISO11898-2. As a successor to the first generation of HS CAN transceivers, the pin assignment and function of the TLE7250GVIO is fully compatible with its predecessor model, the TLE6250GV33. The TLE7250GVIO is optimized to provide an excellent passive behavior in the power-down state. This feature makes the TLE7250GVIO extremely suitable for mixed supply CAN networks. Based on the Infineon Smart Power Technology SPT, the TLE7250GVIO provides excellent ESD immunity together with a very high electromagnetic immunity (EMI). The Infineon Smart Power Technology SPT allows bipolar and CMOS control circuitry in accordance with DMOS power devices to exist on the same monolithic circuit. The TLE7250GVIO and the Infineon SPT technology are AEC qualified and tailored to withstand the harsh conditions of the Automotive Environment. Two different operating modes, additional fail-safe features like TxD time-out and the optimized output slew rates on the CANH and CANL signals make the TLE7250GVIO the ideal choice for large CAN networks with high data transmission rates. Type Package Marking TLE7250GVIO PG-DSO-8 7250GVIO Data Sheet 3 Rev. 1.1, 2014-05-07 TLE7250GVIO Block Diagram 2 Block Diagram 3 Transmitter CANH CANL 5 7 6 Driver Output Stage VCC VIO 1 TxD TempProtection Timeout Mode Control 8 NEN Receiver VCC/2 = Comparator * GND Figure 1 2 4 RxD Block diagram Note: In comparison with the TLE6250GV33, the pin 8 (INH) was renamed as NEN, but the function remains unchanged. NEN stands for Not ENable. Data Sheet 4 Rev. 1.1, 2014-05-07 TLE7250GVIO Pin Configuration 3 Pin Configuration 3.1 Pin Assignment TxD 1 8 NEN GND 2 7 CANH VCC 3 6 CANL RxD 4 5 VIO Figure 2 Pin configuration 3.2 Pin Definitions and Functions Table 1 Pin Definition and Functions Pin Symbol Function 1 TxD Transmit Data Input; internal pull-up to VIO, “low” for “dominant” state. 2 GND Ground 3 VCC Transceiver Supply Voltage; 100 nF decoupling capacitor to GND required. 4 RxD Receive Data Output; “low” in “dominant” state. 5 VIO Digital Supply Voltage Input; supply voltage input to adapt the logical input and output voltage levels of the transceiver to the microcontroller supply. 100 nF decoupling capacitor to GND required. 6 CANL CAN Bus Low Level I/O; “low” in “dominant” state. 7 CANH CAN Bus High Level I/O; “high” in “dominant” state. 8 NEN Not Enable Input1); internal pull-up to VIO, “low” for normal-operating mode. 1) The designation of pin 8 is different in the TLE7250GVIO and its predecessor, the TLE6250GV33. The function of pin 8 remains the same. Data Sheet 5 Rev. 1.1, 2014-05-07 TLE7250GVIO Functional Description 4 Functional Description CAN is a serial bus system that connects microcontrollers, sensors and actuators for real-time control applications. The use of the Control Area Network (abbreviated CAN) within road vehicles is described by the international standard ISO 11898. According to the 7-layer OSI reference model, the physical layer of a CAN bus system specifies the data transmission from one CAN node to all other available CAN nodes within the network. The physical layer specification of a CAN bus system includes all electrical and mechanical specifications of a CAN network. The CAN transceiver is part of the physical layer specification. Several different physical layer standards of CAN networks have been developed in recent years. The TLE7250GVIO is a High Speed CAN transceiver without a dedicated wake-up function. High-speed CAN transceivers without a wake-up function are defined by the international standard ISO 11898-2. 4.1 High Speed CAN Physical Layer TxD VIO t VCC CAN_H CAN_L VIO VCC = = TxD = RxD = CANH = CANL = VDIFF = Digital supply High Speed CAN power supply Input from the microcontroller Output to the microcontroller Voltage on the CANH input/output Voltage on the CANL input/output Differential voltage between CANH and CANL VDIFF = VCANH – VCANL t VDIFF “dominant“ VDIFF = ISO level “dominant“ VDIFF = ISO level “recessive“ “recessive“ t RxD VIO t Figure 3 Data Sheet High Speed CAN bus signals and logic signals 6 Rev. 1.1, 2014-05-07 TLE7250GVIO Functional Description The TLE7250GVIO is a High Speed CAN transceiver, operating as an interface between the CAN controller and the physical bus medium. A HS CAN network is a two-wire, differential network, which allows data transmission rates up to 1 Mbps. The characteristics of a HS CAN network are the two signal states on the CAN bus: “dominant” and “recessive” (see Figure 3). The CANH and CANL pins are the interface to the CAN bus and both pins operate as an input and output. The RxD and TxD pins are the interface to the microcontroller. The TxD pin is the serial data input from the CAN controller, and the RxD pin is the serial data output to the CAN controller. As shown in Figure 1, the HS CAN transceiver TLE7250GVIO includes a receiver and a transmitter unit, allowing the transceiver to send data to the bus medium and monitor the data from the bus medium at the same time. The HS CAN transceiver TLE7250GVIO converts the serial data stream available on the transmit data input TxD, into a differential output signal on the CAN bus, provided by the CANH and CANL pins. The receiver stage of the TLE7250GVIO monitors the data on the CAN bus and converts them to a serial, single-ended signal on the RxD output pin. A logical “low” signal on the TxD pin creates a “dominant” signal on the CAN bus, followed by a logical “low” signal on the RxD pin (see Figure 3). The feature of broadcasting data to the CAN bus and listening to the data traffic on the CAN bus simultaneously is essential to support the bit-to-bit arbitration within CAN networks. The voltage levels for HS CAN transceivers are defined by the ISO 11898-2 and the ISO 11898-5 standards. Whether a data bit is “dominant” or “recessive” depends on the voltage difference between the CANH and CANL pins: VDIFF = VCANH - VCANL. In comparison with other differential network protocols, the differential signal on a CAN network can only be larger than or equal to 0 V. To transmit a “dominant” signal to the CAN bus, the differential signal VDIFF is larger than or equal to 1.5 V. To receive a “recessive” signal from the CAN bus, the differential VDIFF is smaller than or equal to 0.5 V. “Partially-supplied” High Speed CAN networks are those where the CAN bus nodes of one common network have different power supply conditions. Some nodes are connected to the common power supply, while other nodes are disconnected from the power supply and in power-down state. Regardless of whether the CAN bus subscriber is supplied or not, each subscriber connected to the common bus media must not interfere with the communication. The TLE7250GVIO is designed to support “partially-supplied” networks. In the power-down state, the receiver input resistors are switched off and the transceiver input has a high resistance. The voltage level at the digital input TxD and the digital output RxD is determined by the power supply level at the VIO pin. Depending on the voltage level at the VIO pin, the signal levels on the logic pins (NEN, TxD and RxD) are compatible with microcontrollers having 5 V or 3.3 V I/O supply. Usually, the VIO power supply of the transceiver is connected to same power supply as the I/O power supply of the microcontroller. Data Sheet 7 Rev. 1.1, 2014-05-07 TLE7250GVIO Functional Description 4.2 Modes of Operation Two different modes of operation are available on the TLE7250GVIO. Each mode has specific characteristics in terms of quiescent current or data transmission. The digital input pin NEN is used for mode selection. Figure 4 illustrates the different mode changes depending on the status of the NEN pin. After supplying VCC and VIO to the HS CAN transceiver, the TLE7250GVIO starts in stand-by mode. The internal pull-up resistor at the NEN pin sets the TLE7250GVIO to stand-by mode by default. If the microcontroller is up and running, the TLE7250GVIO can switch to any mode of operation within the time period for mode change tMode. start–up supply VCC and VIO VCC < VCC(UV) undervoltage VIO < VIO(UV) detection on VCC and VIO power-down stand-by mode NEN = 1 NEN = 0 NEN = 1 normal-operating mode NEN = 0 Figure 4 Modes of operation The TLE7250GVIO has 2 major modes of operation: • • Stand-by mode Normal-operating mode Table 2 Mode Modes of Operation Bus Bias Comments Normal-operating “low” mode VCC/2 The transmitter is active. The receiver is active. Stand-by “high” GND The transmitter is disabled. The receiver is disabled. VCC off “low” or “high” floating The transmitter is disabled. The receiver is disabled. Data Sheet NEN 8 Rev. 1.1, 2014-05-07 TLE7250GVIO Functional Description 4.3 Normal-operating Mode In the normal-operating mode, the HS CAN transceiver TLE7250GVIO sends the serial data stream on the TxD pin to the CAN bus. The data on the CAN bus is displayed at the RxD pin simultaneously. In normal-operating mode, all functions of the TLE7250GVIO are active: • • • • The transmitter is active and drives data from the TxD to the CAN bus. The receiver is active and provides the data from the CAN bus to the RxD pin. The bus biasing is set to VCC/2. The undervoltage monitoring at the power supply VCC and at the power supply VIO is active. To enter the normal-operating mode, set the NEN pin to logical “low” (see Table 2 or Figure 4). The NEN pin has an internal pull-up resistor to the power-supply VIO. 4.4 Stand-by Mode The stand-by mode is an idle mode of the TLE7250GVIO with optimized power consumption. In the stand-by mode, the TLE7250GVIO can not send or receive any data. The transmitter and the receiver unit are disabled. Both CAN bus pins, CANH and CANL are connected to GND via the input resistors. • • • • The transmitter is disabled. The receiver is disabled. The input resistors of the receiver are connected to GND. The undervoltage monitoring at the power supply VCC and at the power supply VIO is active. To enter the stand-by mode, set the pin NEN to logical “high” (see Table 2 or Figure 4). The NEN pin has an internal pull-up resistor to the power-supply VIO. If the stand-by mode is not used in the final application, the NEN pin needs to be connected to GND. 4.5 Power-down State The power-down state means that the TLE7250GVIO is not supplied. In power-down state, the differential input resistors of the receiver are switched off. The CANH and CANL bus interface of the TLE7250GVIO act as highimpedance input with a very small leakage current. The high-ohmic input does not influence the “recessive” level of the CAN network and allows an optimized EME performance of the entire CAN network. Data Sheet 9 Rev. 1.1, 2014-05-07 TLE7250GVIO Fail-safe Functions 5 Fail-safe Functions 5.1 Short-circuit Protection The CANH and CANL bus outputs are short-circuit proof, either against GND or a positive supply voltage. A current limiting circuit protects the transceiver against damage. If the device heats up due to a continuous short on the CANH or CANL, the internal overtemperature protection switches off the bus transmitter. 5.2 Unconnected Logic Pins All logic input pins have an internal pull-up resistor to VIO. In case the VIO supply is activated and the logical pins are open or floating, the TLE7250GVIO enters the stand-by mode by default. In stand-by mode, the transmitter of the TLE7250GVIO is disabled, the bus bias is connected to GND and the HS CAN TLE7250G transceiver does not influence the data on the CAN bus. 5.3 TxD Time-out Function The TxD time-out feature protects the CAN bus against permanent blocking in case the logical signal on the TxD pin is continuously “low”. A continuous “low” signal on the TxD pin can have its root cause in a locked-up microcontroller or in a short on the printed circuit board for example. In the normal-operating mode, a logical “low” signal on the TxD pin for the time t > tTxD enables the TxD time-out feature and the TLE7250GVIO disables the transmitter (see Figure 5). The receiver is still active and the data on the bus continues to be monitored by the RxD output pin. t > tTxD TxD time-out CANH CANL TxD time-out released t TxD t RxD t Figure 5 TxD Time-out function Figure 5 illustrates how the transmitter is deactivated and activated again. A permanent “low” signal on the TxD input pin activates the TxD time-out function and deactivates the transmitter. To release the transmitter after a TxD time-out event, the TLE7250GVIO requires a signal change on the TxD input pin from logical “low” to logical “high”. 5.4 Undervoltage Detection The HS CAN transceiver TLE7250GVIO is provided with undervoltage detection at the power supply VCC and at the power supply VIO. In case of undervoltage at VCC or VIO, the undervoltage detection changes the operating mode of TLE7250GVIO to the stand-by mode, regardless of the logical signal on the NEN pin (see Figure 6). If the transceiver TLE7250GVIO recovers from the undervoltage condition, the operating mode is restored to the programmed mode by the NEN pin. Data Sheet 10 Rev. 1.1, 2014-05-07 TLE7250GVIO Fail-safe Functions hysteresis VCC(UV,H) Supply voltage VCC power-down reset level VCC(UV) delay time undervoltage recovery tDelay(UV) NEN = 0 normal-operating mode stand-by mode normal-operating mode1) Supply voltage VIO hysteresis VIO(UV,H) power-down reset level VIO(UV) delay time undervoltage recovery tDelay(UV) NEN = 0 normal-operating mode stand-by mode normal-operating mode1) 1) Assuming the logical signal on the pin NEN keeps its values during the undervoltage event. In this case NEN remains “low“. Figure 6 Data Sheet Undervoltage detection at the VCC or VIO Pins 11 Rev. 1.1, 2014-05-07 TLE7250GVIO Fail-safe Functions 5.5 Overtemperature Protection Overtemperature event TJSD TJ ΔT Cool Down (shut-down temperature) switch-on transmitter t CANH CANL t TxD t RxD t Figure 7 Overtemperature protection The TLE7250GVIO has an integrated overtemperature detection circuit to protect the device against thermal overstress of the transmitter. In case of an overtemperature condition, the temperature sensor will disable the transmitter (see Figure 1). After the device cools down, the transmitter is activated again (see Figure 7). A hysteresis is implemented within the temperature sensor. Data Sheet 12 Rev. 1.1, 2014-05-07 TLE7250GVIO General Product Characteristics 6 General Product Characteristics 6.1 Absolute Maximum Ratings Table 3 Absolute Maximum Ratings of Voltage, Current and Temperatures1) All voltages with respect to ground; positive current flowing into the pin; (unless otherwise specified) Pos. Parameter Symbol Limit Values Min. Max. Unit Remarks Voltage 6.1.1 Supply voltage VCC -0.3 6.0 V – 6.1.2 Logic supply voltage VIO -0.3 6.0 V – 6.1.3 CANH DC voltage against GND VCANH -40 40 V – 6.1.4 CANL DC voltage against GND VCANL -40 40 V – 6.1.5 Differential voltage VCAN diff between CANH and CANL -40 40 V – 6.1.6 Logic voltage at logic input VMax_In pins NEN, TxD -0.3 6.0 V – 6.1.7 Logic voltage at logic output VMax_Out pin RxD -0.3 VIO V – Temperature 6.1.8 Junction temperature Tj -40 150 °C – 6.1.9 Storage temperature TS -55 150 °C – ESD Immunity 6.1.10 ESD immunity at CANH, CANL against GND VESD_HBM_CAN -8 8 kV HBM (100pF via 1.5 kΩ)2) 6.1.11 ESD immunity at all other pins VESD_HBM_All -2 2 kV HBM (100pF via 1.5 kΩ)2) 6.1.12 ESD immunity to GND (all pins) VESD_CDM 750 V CDM3) -750 1) Not subject to production test, specified by design 2) ESD susceptibility Human Body Model “HBM” according to ANSI/ESDA/JEDEC JS-001 3) ESD susceptibility, Charge Device Model “CDM” according to EIA/JESD22-C101 or ESDA STM5.3.1 Note: Within the functional range the IC operates as described in the circuit description. The electrical characteristics are specified within the conditions given in the associated electrical characteristics table. Data Sheet 13 Rev. 1.1, 2014-05-07 TLE7250GVIO General Product Characteristics 6.2 Functional Range Table 4 Operating Range Pos. Parameter Symbol Limit Values Min. Max. Unit Conditions Supply Voltage 6.2.1 Transceiver supply voltage VCC 4.5 5.5 V – 6.2.2 Logical supply voltage VIO 3.0 5.5 V – Tj -40 150 °C 1) Thermal Parameter 6.2.3 Junction temperature 1) Not subject to production test, specified by design Note: Within the functional range the IC operates as described in the circuit description. The electrical characteristics are specified within the conditions given in the associated electrical characteristics table. 6.3 Thermal Characteristics Note: This thermal data was generated in accordance with JEDEC JESD51 standards. For more information, please visit www.jedec.org. Thermal Resistance1) Table 5 Pos. Parameter Symbol Limit Values Unit Remarks Min. Typ. Max. – 130 – K/W 2) Thermal Resistance 6.3.1 Junction to ambient1) RthJA Thermal Shut-down Junction Temperature 6.3.2 Thermal shut-down temperature TJSD 150 175 200 °C – 6.3.3 Thermal shut-down hysteresis ΔT – 10 – K – 1) Not subject to production test, specified by design 2) The RthJA value specified, is according to Jedec JESD51-2,-7 at natural convection on the FR4 2s2p board; The product (TLE7250GVIO) was simulated on a 76.2 x 114.3 x 1.5 mm board with 2 inner copper layers (2 x 70 µm Cu, 2 x 35 µm Cu). Data Sheet 14 Rev. 1.1, 2014-05-07 TLE7250GVIO Electrical Characteristics 7 Electrical Characteristics 7.1 Functional Device Characteristics Table 6 Electrical Characteristics 4.5 V < VCC < 5.5 V; 3.0 V < VIO < 5.5 V; RL = 60 Ω; -40 °C < Tj < +150 °C; all voltages with respect to ground; positive current flowing into the pin; unless otherwise specified. Pos. Parameter Symbol Limit Values Unit Remarks Min. Typ. Max. Current Consumption 7.1.1 Current consumption at VCC ICC – 2 6 mA “recessive” state; VTxD = VIO 7.1.2 Current consumption at VCC ICC – 35 60 mA “dominant” state; VTxD = “low” 7.1.3 Current consumption at VIO IIO – 0.2 1 mA normal-operating mode; NEN = “low” 7.1.4 Current consumption stand-by mode ICC(STB) – 4 15 μA 7.1.5 Current consumption stand-by mode IIO(STB) – 2 10 μA VCC = VIO = 5 V, TxD = VIO, NEN = VIO VCC = VIO = 5 V, TxD = VIO, NEN = VIO VCC(UV) VCC(UV,H) 1.3 3.2 4.3 V – – 400 – mV 1) VIO(UV) VIO(UV,H) 1.0 2.4 3.0 V – – 200 – mV 1) tDelay(UV) – – 50 μs 1) 7.1.11 “High” level output current IRD,H – -4 -2 mA VRxD = VIO - 0.4 V, VDIFF < 0.5 V 7.1.12 “Low” level output current IRD,L 2 4 – mA VRxD = 0.4 V, VDIFF > 0.9 V 7.1.13 “High” level input voltage threshold VTD,H – 0.5 × 0.7 × V “recessive” state VIO VIO 7.1.14 “Low” level input voltage threshold VTD,L 0.3 × 0.4 × – V “dominant” state VIO VIO 7.1.15 TxD pull-up resistance RTD VHYS(TxD) tTxD 10 25 50 kΩ – Supply Reset VCC undervoltage monitor 7.1.7 VCC undervoltage monitor 7.1.6 hysteresis VIO undervoltage monitor 7.1.9 VIO undervoltage monitor 7.1.8 hysteresis 7.1.10 VCC and VIO undervoltage delay time (see Figure 6) Receiver Output: RxD Transmission Input: TxD 7.1.16 TxD input hysteresis 7.1.17 TxD permanent “dominant” disable time Data Sheet – 800 – mV 1) 0.3 – 1.0 ms – 15 Rev. 1.1, 2014-05-07 TLE7250GVIO Electrical Characteristics Table 6 Electrical Characteristics (cont’d) 4.5 V < VCC < 5.5 V; 3.0 V < VIO < 5.5 V; RL = 60 Ω; -40 °C < Tj < +150 °C; all voltages with respect to ground; positive current flowing into the pin; unless otherwise specified. Pos. Parameter Symbol Limit Values Unit Remarks Min. Typ. Max. 0.5 × 0.7 × VIO VIO Not Enable Input NEN 7.1.18 “High” level input voltage threshold VNEN,H – 7.1.19 “Low” level input voltage threshold VNEN,L 0.3 × 0.4 × VIO VIO 7.1.20 NEN pull-up resistance RNEN 10 VHYS(NEN) – 25 200 7.1.22 Differential receiver threshold “dominant” VDIFF,(D) – 7.1.23 Differential receiver threshold “recessive” VDIFF,(R) 7.1.24 Differential receiver input range “dominant” V stand-by mode – V normal-operating mode 50 kΩ – – mV 1) 0.75 0.9 V normal-operating mode 0.5 0.65 – Vdiff,rdN 0.9 – 5.0 V 1) normal-operating mode 7.1.25 Differential receiver input range “recessive” Vdiff,drN -1.0 – 0.5 V 1) normal-operating mode 7.1.26 Common mode range CMR -12 – 12 V VCC = 5 V 7.1.27 Differential receiver hysteresis Vdiff,hys – 100 – mV 1) 7.1.28 CANH, CANL input resistance Ri 10 20 30 kΩ “recessive” state 20 40 60 kΩ “recessive” state “recessive” state 7.1.21 NEN input hysteresis Bus Receiver 7.1.29 Differential input resistance Rdiff normal-operating mode 7.1.30 Input resistance deviation between CANH and CANL Δ Ri -3 – 3 % 1) 7.1.31 Input capacitance CANH, CANL versus GND CIN – 20 40 pF 1) VTxD = VIO 7.1.32 Differential input capacitance CInDiff – 10 20 pF 1) VTxD = VIO 7.1.33 CANL/CANH “recessive” output voltage VCANL/H 2.0 2.5 3.0 V no load; VTxD = VIO 7.1.34 CANH, CANL “recessive” output voltage difference Vdiff -500 – 50 mV no load; VTxD = VIO 7.1.35 CANL “dominant” output voltage VCANL 0.5 – 2.25 V 4.75 V ≤ VCC ≤ 5.25 V, VTxD = 0 V, 50 Ω < RL < 65 Ω 7.1.36 CANH “dominant” output voltage VCANH 2.75 – 4.5 V 4.75 V ≤ VCC ≤ 5.25 V, VTxD = 0 V, 50 Ω < RL < 65 Ω 7.1.37 CANH, CANL “dominant” output voltage difference Vdiff = VCANH - VCANL Vdiff 1.5 – 3.0 V 4.75 V ≤ VCC ≤ 5.25 V, VTxD = 0 V, 50 Ω < RL < 65 Ω 7.1.38 Driver symmetry VSYM = VCANH + VCANL VSYM 4.5 – 5.5 V VTxD = 0 V, VCC = 5 V, 50 Ω < RL < 65 Ω Bus Transmitter Data Sheet 16 Rev. 1.1, 2014-05-07 TLE7250GVIO Electrical Characteristics Table 6 Electrical Characteristics (cont’d) 4.5 V < VCC < 5.5 V; 3.0 V < VIO < 5.5 V; RL = 60 Ω; -40 °C < Tj < +150 °C; all voltages with respect to ground; positive current flowing into the pin; unless otherwise specified. Pos. Parameter Symbol Limit Values Unit Remarks Min. Typ. Max. 7.1.39 CANL short-circuit current ICANLsc 40 80 100 mA VTxD = 0 V, VCC = 5 V, t < tTxD, VCANLshort = 18 V 7.1.40 CANH short-circuit current ICANHsc -100 -80 -40 mA VTxD = 0 V, VCC = 5 V, t < tTxD, VCANHshort = 0 V 7.1.41 Leakage current CANH ICANH,lk -5 0 5 μA 7.1.42 Leakage current CANL ICANL,lk -5 0 5 μA VCC = 0 V, VCANH = VCANL, 0 V < VCANH < 5 V VCC = 0 V, VCANH = VCANL, 0 V < VCANL < 5 V Dynamic CAN Transceiver Characteristics 7.1.43 Propagation delay TxD-to-RxD “low” (“recessive” to “dominant”) td(L),TR 30 180 255 ns CL = 100 pF, VCC = 5 V, CRxD = 15 pF 7.1.44 Propagation delay TxD-to-RxD “high” (“dominant” to “recessive”) td(H),TR 30 200 255 ns CL = 100 pF, VCC = 5 V, CRxD = 15 pF 7.1.45 Propagation delay TxD “low” to bus “dominant” td(L),T – 100 – ns 1) 7.1.46 Propagation delay TxD “high” to bus “recessive” td(H),T – 90 – ns 7.1.47 Propagation delay bus “dominant” to RxD “low” td(L),R – 80 – ns 7.1.48 Propagation delay bus “recessive” to RxD “high” td(H),R – 110 – ns 7.1.49 Time for mode change tMode – – 10 μs CL = 100 pF, VCC = 5 V, CRxD = 15 pF 1) CL = 100 pF, VCC = 5 V, CRxD = 15 pF 1) CL = 100 pF, VCC = 5 V, CRxD = 15 pF 1) CL = 100 pF, VCC = 5 V, CRxD = 15 pF 1) 1) Not subject to production test, specified by design Data Sheet 17 Rev. 1.1, 2014-05-07 TLE7250GVIO Electrical Characteristics 7.2 Diagrams VIO 7 CANH TxD NEN CL 5 100 nF 1 8 RL RxD 6 4 CRxD CANL GND VCC 3 100 nF 2 Figure 8 Simplified test circuit VTxD VIO GND VDIFF td(L),T 0.9V 0.5V td(L),R VRxD t td(H),T t td(H),R td(L),TR td(H),TR VIO 0.7 x VIO 0.3 x VIO GND t Figure 9 Data Sheet Timing diagram for dynamic characteristics 18 Rev. 1.1, 2014-05-07 TLE7250GVIO Application Information 8 Application Information 8.1 ESD Immunity According to IEC61000-4-2 Tests for ESD immunity according to IEC61000-4-2, “GUN test” (150 pF, 330 Ω), have been performed. The results and test conditions are available in a separate test report. Table 7 ESD Immunity according to IEC61000-4-2 Test performed Result Unit Remarks Electrostatic discharge voltage at CANH and CANL pins against GND ≥ +8 kV 1) Positive pulse Electrostatic discharge voltage at CANH and CANL pins against GND ≤ -8 kV 1) Negative pulse 1) ESD susceptibility “ESD GUN” according to GIFT / ICT paper: “EMC Evaluation of CAN Transceivers, version 03/02/ IEC TS 62228”, section 4.3. (DIN EN 61000-4-2) Tested by external test house (IBEE Zwickau, EMC test report no.: 05-12-11). Data Sheet 19 Rev. 1.1, 2014-05-07 TLE7250GVIO Application Information 8.2 Application Example VBAT I Q1 22 uF TLE4476D CANH CANL EN GND 100 nF 100 nF Q2 3 VCC 22 uF 120 Ohm VIO TLE7250GVIO NEN 7 CANH a 6 TxD RxD CANL 100 nF 5 8 VCC Out 1 Out 4 In Microcontroller e.g. XC22xx Optional: Common Mode Choke GND GND 2 Example ECU Design I Q1 22 uF TLE4476D EN GND 100 nF Q2 3 VCC 22 uF VIO TLE7250GVIO 7 6 NEN CANH TxD RxD CANL 5 100 nF 100 nF 8 1 4 Optional: Common Mode Choke VCC Out Out In Microcontroller e.g. XC22xx GND 120 Ohm GND 2 CANH CANL Figure 10 Simplified application for the TLE7250GVIO 8.3 Further Application Information • • Please contact us for information regarding the FMEA pin. For further information you may visit http://www.infineon.com/transceiver Data Sheet 20 Rev. 1.1, 2014-05-07 TLE7250GVIO Package Outlines 9 Package Outlines 0.1 2) 0.41+0.1 -0.06 0.2 8 5 1 4 5 -0.2 1) M 0.19 +0.06 4 -0.2 C B 8 MAX. 1.27 1.75 MAX. 0.175 ±0.07 (1.45) 0.35 x 45˚ 1) 0.64 ±0.25 6 ±0.2 A B 8x 0.2 M C 8x A Index Marking 1) Does not include plastic or metal protrusion of 0.15 max. per side 2) Lead width can be 0.61 max. in dambar area GPS01181 Figure 11 PG-DSO-8 (Plastic dual small outline PG-DSO-8-16) Green Product (RoHS-compliant) The device has been designed as a green product to meet the world-wide customer requirements for environmentfriendly products and to be compliant with government regulations. Green products are RoHS-compliant (i.e Pbfree finish on leads and suitable for Pb-free soldering according to IPC/JEDEC J-STD-020). For further information on alternative packages, please visit our website: http://www.infineon.com/packages. Data Sheet 21 Dimensions in mm Rev. 1.1, 2014-05-07 TLE7250GVIO Revision History 10 Revision History Revision Date Changes 1.1 2014-05-07 Update from Data Sheet Rev.: 1.0. • • • • • • • • • • 1.0 Data Sheet 2012-03-01 All pages: Revision and date update Page 3, Overview: Feature list updated (“Extended supply range at VCC and VIO”). Page 14, Table 4, Parameter 6.2.1, Supply range updated (4.5 V < VCC < 5.5 V). Page 14, Table 4, Parameter 6.2.2: Supply range updated (3.0 V < VIO < 5.5 V). Page 15, Table 6: Table header updated (4.5 V < VCC < 5.5 V, 3.0 V < VIO < 5.5 V). Page 16, Table 6, Parameter 7.1.35: Remark added (“4.75 V≤VCC≤5.25 V”). Page 16, Table 6, Parameter 7.1.36: Remark added (“4.75 V≤VCC≤5.25 V”). Page 16, Table 6, Parameter 7.1.37: Remark added (“4.75 V≤VCC≤5.25 V”). Page 20, Figure 10: Picture updated. Page 22: Revision history updated. Data Sheet Rev. 1.0 created 22 Rev. 1.1, 2014-05-07 Edition 2014-05-07 Published by Infineon Technologies AG 81726 Munich, Germany © 2006 Infineon Technologies AG All Rights Reserved. Legal Disclaimer The information given in this document shall in no event be regarded as a guarantee of conditions or characteristics. With respect to any examples or hints given herein, any typical values stated herein and/or any information regarding the application of the device, Infineon Technologies hereby disclaims any and all warranties and liabilities of any kind, including without limitation, warranties of non-infringement of intellectual property rights of any third party. Information For further information on technology, delivery terms and conditions and prices, please contact the nearest Infineon Technologies Office (www.infineon.com). Warnings Due to technical requirements, components may contain dangerous substances. For information on the types in question, please contact the nearest Infineon Technologies Office. Infineon Technologies components may be used in life-support devices or systems only with the express written approval of Infineon Technologies, if a failure of such components can reasonably be expected to cause the failure of that life-support device or system or to affect the safety or effectiveness of that device or system. Life support devices or systems are intended to be implanted in the human body or to support and/or maintain and sustain and/or protect human life. If they fail, it is reasonable to assume that the health of the user or other persons may be endangered.