TLE9250SJXUMA1

TLE9250 Hi gh Speed CAN FD Transceiver 1 Overview Features • Fully compliant to ISO 11898-2 (2016) and SAE J2284-4/-5 • Reference device and part of Interoperability Test Specification for CAN Transceiver • Guaranteed loop delay symmetry for CAN FD data frames up to 5 MBit/s • Very low electromagnetic emission (EME) allows the use without additional common mode choke • Wide common mode range for electromagnetic immunity (EMI) • Excellent ESD robustness +/-8kV (HBM) and +/-11kV (IEC 61000-4-2) • Extended supply range on the VCC • CAN short circuit proof to ground, battery and VCC • TxD time-out function • Very low CAN bus leakage current in power-down state • Overtemperature protection • Protected against automotive transients according ISO 7637 and SAE J2962-2 standards • Receive-only mode and Power-save mode • Green Product (RoHS compliant) • Small, leadless TSON8 package designed for automated optical inspection (AOI) PG-TSON-8 PG-DSO-8 Potential applications • Engine Control Unit (ECUs) • Electric Power Steering • Transmission Control Units (TCUs) • Chassis Control Modules Product validation Qualified for automotive applications. Product validation according to AEC-Q100. Datasheet www.infineon.com/automotive-transceiver 1 Rev. 1.11 2019-09-19 High Speed CAN FD Transceiver TLE9250 Overview Description Type Package Marking TLE9250LE PG-TSON-8 9250 TLE9250SJ PG-DSO-8 9250 The TLE9250 is the latest Infineon high-speed CAN transceiver generation, used inside HS CAN networks for automotive and also for industrial applications. It is designed to fulfill the requirements of ISO 11898-2 (2016) physical layer specification and respectively also the SAE standards J1939 and J2284. The TLE9250 is available in a PG-DSO-8 package and in a small, leadless PG-TSON-8 package. Both packages are RoHS compliant and halogen free. The PG-TSON-8 package supports the solder joint requirements for automated optical inspection (AOI). As an interface between the physical bus layer and the HS CAN protocol controller, the TLE9250 protects the microcontroller against interferences generated inside the network. A very high ESD robustness and the perfect RF immunity allows the use in automotive applications without adding additional protection devices, like suppressor diodes for example. While the transceiver TLE9250 is not supplied the bus is switched off and illustrates an ideal passive behavior with the lowest possible load to all other subscribers of the HS CAN network. Based on the high symmetry of the CANH and CANL output signals, the TLE9250 provides a very low level of electromagnetic emission (EME) within a wide frequency range. The TLE9250 fulfills even stringent EMC test limits without additional external circuit, like a common mode choke for example. The perfect transmitter symmetry combined with the optimized delay symmetry of the receiver enables the TLE9250 to support CAN FD data frames. Depending on the size of the network and the along coming parasitic effects the device supports bit rates up to 5 MBit/s. Fail-safe features like overtemperature protection, output current limitation or the TxD time-out feature protect the TLE9250 and the external circuitry from irreparable damage. Datasheet 2 Rev. 1.11 2019-09-19 High Speed CAN FD Transceiver TLE9250 Table of contents 1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Potential applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Product validation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Table of contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 3 3.1 3.2 Pin configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Pin assignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Pin definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 4 4.1 4.2 4.3 General product characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Functional range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Thermal resistance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 5.1 High-speed CAN functional description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 High-speed CAN physical layer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 6 6.1 6.2 6.3 6.4 Modes of operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Normal-operating mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Receive-only mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Power-save mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Power-down state . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 7.1 7.2 Changing the mode of operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Power-up and power-down . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Mode change by the NEN and NRM pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 8 8.1 8.2 8.3 8.4 8.5 Fail safe functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Short circuit protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Unconnected logic pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TxD time-out function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Overtemperature protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Delay time for mode change . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 9.1 9.2 Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Functional device characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 10 10.1 10.2 10.3 Application information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ESD robustness according to IEC61000-4-2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Application example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Further application information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Package outline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 12 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Datasheet 3 6 6 7 7 10 11 11 11 12 15 15 15 15 15 16 23 23 23 24 Rev. 1.11 2019-09-19 High Speed CAN FD Transceiver TLE9250 Block diagram 2 Block diagram 3 VCC Transmitter CANH CANL 1 7 Driver Tempprotection 6 TxD Timeout 8 Mode control 5 NEN NRM Receiver Normal-mode receiver 4 RxD VCC/2 = Bus-biasing GND 2 Figure 1 Datasheet Functional block diagram 4 Rev. 1.11 2019-09-19 High Speed CAN FD Transceiver TLE9250 Pin configuration 3 Pin configuration 3.1 Pin assignment TxD 1 8 NEN GND 2 7 CANH VCC 3 6 CANL RxD 4 5 NRM TxD 1 8 NEN GND 2 7 CANH VCC 3 6 CANL RxD 4 5 NRM PAD (Top-side x-ray view) Figure 2 3.2 Pin configuration Pin definitions Table 1 Pin definitions and functions Pin No. Symbol Function 1 TxD Transmit Data Input; Internal pull-up to VCC, “low” for dominant state. 2 GND Ground 3 VCC Transmitter Supply Voltage; 100 nF decoupling capacitor to GND required. 4 RxD Receive Data Output; “low” in dominant state. 5 NRM Not Receive-Only Input; Control input for selecting Receive-only mode, Internal pull-up to VCC, “low” for receive-only mode. 6 CANL CAN Bus Low Level I/O; “low” in dominant state. 7 CANH CAN Bus High Level I/O; “high” in dominant state. 8 NEN Not Enable Input; Internal pull-up to VCC, “low” for Normal-operating mode or Receive-only mode. PAD – Connect to PCB heat sink area. Do not connect to other potential than GND. Datasheet 5 Rev. 1.11 2019-09-19 High Speed CAN FD Transceiver TLE9250 General product characteristics 4 General product characteristics 4.1 Absolute maximum ratings Table 2 Absolute maximum ratings voltages, currents and temperatures1) All voltages with respect to ground; positive current flowing into pin; (unless otherwise specified) Parameter Symbol Values Min. Typ. Max. Unit Note or Test Condition Number Voltages Transmitter supply voltage VCC -0.3 – 6.0 V – P_8.1.1 CANH and CANL DC voltage versus GND VCANH -40 – 40 V – P_8.1.3 Differential voltage between CANH and CANL VCAN_Diff -40 – 40 V – P_8.1.4 Voltages at the digital I/O pins: VMAX_IO1 NEN, NRM, RxD, TxD -0.3 – 6.0 V – P_8.1.5 Voltages at the digital I/O pins: VMAX_IO2 NEN, NRM, RxD, TxD -0.3 – VCC + 0.3 V – P_8.1.6 IRxD -5 – 5 mA – P_8.1.7 Junction temperature Tj -40 – 150 °C – P_8.1.8 Storage temperature TS -55 – 150 °C – P_8.1.9 ESD immunity at CANH, CANL VESD_HBM_CAN -8 versus GND – 8 kV HBM (100 pF via 1.5 kΩ)2) P_8.1.11 ESD immunity at all other pins VESD_HBM_ALL -2 – 2 kV HBM (100 pF via 1.5 kΩ)2) P_8.1.12 – 750 V CDM3) P_8.1.13 Currents RxD output current Temperatures ESD Resistivity ESD immunity all pins VESD_CDM -750 1) Not subject to production test, specified by design 2) ESD susceptibility, Human Body Model “HBM” according to ANSI/ESDA/JEDEC JS-001 3) ESD susceptibility, Charge Device Model “CDM” according to EIA/JESD22-C101 or ESDA STM5.3.1 Note: Datasheet Stresses above the ones listed here may cause permanent damage to the device. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Integrated protection functions are designed to prevent IC destruction under fault conditions described in the data sheet. Fault conditions are considered as “outside” normal-operating range. Protection functions are not designed for continuos repetitive operation. 6 Rev. 1.11 2019-09-19 High Speed CAN FD Transceiver TLE9250 General product characteristics 4.2 Table 3 Functional range Functional range Parameter Symbol Values Min. Typ. Max. Unit Note or Test Condition Number VCC 4.5 – 5.5 V – P_8.2.1 Tj -40 – 150 °C 1) P_8.2.3 Supply Voltages Transmitter supply voltage Thermal Parameters Junction temperature 1) Not subject to production test, specified by design. Note: Within the functional range the IC operates as described in the circuit description. The electrical characteristics are specified within the conditions given in the related electrical characteristics table. 4.3 Thermal resistance Note: This thermal data was generated in accordance with JEDEC JESD51 standards. For more information, please visit www.jedec.org. Table 4 Thermal resistance1) Parameter Symbol Values Min. Typ. Max. Unit Note or Test Condition Number Thermal Resistances Junction to Ambient PG-TSON-8 RthJA_TSON8 – 65 – K/W 2) P_8.3.1 Junction to Ambient PG-DSO-8 RthJA_DSO8 – 120 – K/W 2) P_8.3.2 Thermal Shutdown (junction temperature) Thermal shutdown temperature, rising TJSD 170 180 190 °C temperature P_8.3.3 falling: Min. 150°C Thermal shutdown hysteresis ∆T 5 10 20 K – P_8.3.4 1) Not subject to production test, specified by design 2) Specified RthJA value is according to Jedec JESD51-2,-7 at natural convection on FR4 2s2p board. The product (TLE9250) was simulated on a 76.2 x 114.3 x 1.5 mm board with 2 inner copper layers (2 x 70µm Cu, 2 x 35µm Cu) Datasheet 7 Rev. 1.11 2019-09-19 High Speed CAN FD Transceiver TLE9250 High-speed CAN functional description 5 High-speed CAN functional description HS CAN is a serial bus system that connects microcontrollers, sensors and actuators for real-time control applications. The use of the Controller Area Network (abbreviated CAN) within road vehicles is described by the international standard ISO 11898. According to the 7-layer OSI reference model the physical layer of a HS CAN bus system specifies the data transmission from one CAN node to all other available CAN nodes within the network. The physical layer specification of a CAN bus system includes all electrical specifications of a CAN network. The CAN transceiver is part of the physical layer specification. Several different physical layer standards of CAN networks have been developed in recent years. 5.1 High-speed CAN physical layer VCC = TxD = TxD VCC t CANH CANL VCC Transmitter supply voltage Transmit data input from the microcontroller RxD = Receive data output to the microcontroller CANH = Bus level on the CANH input/output CANL = Bus level on the CANL input/output VDiff = Differential voltage between CANH and CANL VDiff = VCANH – VCANL t VDiff VCC “dominant” receiver threshold “recessive” receiver threshold t RxD VCC tLoop(H,L) Figure 3 Datasheet tLoop(L,H) t High-speed CAN bus signals and logic signals 8 Rev. 1.11 2019-09-19 High Speed CAN FD Transceiver TLE9250 High-speed CAN functional description The TLE9250 is a high-speed CAN transceiver, operating as an interface between the CAN controller and the physical bus medium. A HS CAN network is a two wire, differential network which allows data transmission rates up to 5 MBit/s. The characteristic for a HS CAN network are the two signal states on the CAN bus: dominant and recessive (see Figure 3). The CANH and CANL pins are the interface to the CAN bus and both pins operate as an input and output. The RxD and TxD pins are the interface to the microcontroller. The pin TxD is the serial data input from the CAN controller, the RxD pin is the serial data output to the CAN controller. As shown in Figure 1, the HS CAN transceiver TLE9250 includes a receiver and a transmitter unit, allowing the transceiver to send data to the bus medium and monitor the data from the bus medium at the same time. The HS CAN transceiver TLE9250 converts the serial data stream which is available on the transmit data input TxD, into a differential output signal on the CAN bus, provided by the CANH and CANL pins. The receiver stage of the TLE9250 monitors the data on the CAN bus and converts them to a serial, single-ended signal on the RxD output pin. A logical “low” signal on the TxD pin creates a dominant signal on the CAN bus, followed by a logical “low” signal on the RxD pin (see Figure 3). The feature, broadcasting data to the CAN bus and listening to the data traffic on the CAN bus simultaneously is essential to support the bit-to-bit arbitration within CAN networks. The voltage levels for HS CAN transceivers are defined in ISO 11898-2. Whether a data bit is dominant or recessive depends on the voltage difference between the CANH and CANL pins: VDiff = VCANH - VCANL. To transmit a dominant signal to the CAN bus the amplitude of the differential signal VDiff is higher than or equal to 1.5 V. To receive a recessive signal from the CAN bus the amplitude of the differential VDiff is lower than or equal to 0.5 V. “Partially-supplied” high-speed CAN networks are those where the CAN bus nodes of one common network have different power supply conditions. Some nodes are connected to the common power supply, while other nodes are disconnected from the power supply and in power-down state. Regardless of whether the CAN bus subscriber is supplied or not, each subscriber connected to the common bus media must not interfere in the communication. The TLE9250 is designed to support “partially-supplied” networks. In power-down state, the receiver input resistors are switched off and the transceiver input has a high resistance. For permanently supplied ECU's, the HS CAN transceiver TLE9250 provides a Power-save mode. In Power-save mode, the power consumption of the TLE9250 is optimized to a minimum The voltage level on the digital input TxD and the digital output RxD is determined by the power supply level at the VCC pin. Depending on the voltage level at the VCC pin, the signal levels on the logic pins (STB, TxD and RxD) are compatible with microcontrollers having a 5 V I/O supply. Datasheet 9 Rev. 1.11 2019-09-19 High Speed CAN FD Transceiver TLE9250 Modes of operation 6 Modes of operation The TLE9250 supports three different modes of operation (see Figure 4 and Table 5): • Normal-operating mode • Power-save mode • Receive-only mode Mode changes are either triggered by the mode selection input pin NEN and NRM . An undervoltage event on the supply VCC powers down the TLE9250. Normal-operating mode VCC “on” NEN “0” NRM “1” NEN NRM 0 Power-down state NEN NRM “X” “X” VCC VCC “on” NEN “1” NRM “X” Mode state diagram Table 5 Modes of operation “on” VCC “on” NEN “0” NRM “1” VCC “on” NEN “0” NRM “0” “off” Figure 4 1 VCC “on” NEN “0” NRM “1” VCC VCC “on” NEN “0” NRM “0” Receive-only mode NEN NRM 0 VCC “on” NEN “1” NRM “X” Power-save mode NEN NRM 1 “X” VCC Mode NEN NRM Normal-operating “low” Power-save 0 VCC “on” VCC “on” NEN “1” NRM “X” VCC “on” NEN “0” NRM “0” VCC “on” Bus Bias Transmitter Normal-mode Receiver “high” “on” VCC/2 “on” “on” “high” “X” “on” floating “off” “off” Receive-only “low” “low” “on” VCC/2 “off” “on” Power-down state “X” “X” “off” floating “off” “off” Datasheet 10 Rev. 1.11 2019-09-19 High Speed CAN FD Transceiver TLE9250 Modes of operation 6.1 Normal-operating mode In Normal-operating mode the transceiver TLE9250 sends and receives data from the HS CAN bus. All functions are active (see also Figure 4 and Table 5): • The transmitter is active and drives the serial data stream on the TxD input pin to the bus pins CANH and CANL. • The normal-mode receiver is active and converts the signals from the bus to a serial data stream on the RxD output. • The RxD output pin indicates the data received by the normal-mode receiver. • The bus biasing is connected to VCC/2. • The NEN and NRM input pin is active and changes the mode of operation. • The TxD time-out function is enabled and disconnects the transmitter in case a time-out is detected. • The overtemperature protection is enabled and disconnects the transmitter in case an overtemperature is detected. • The undervoltage detection on VCC is enabled and powers down the device in case of detection . Normal-operating mode is entered from Power-save mode and Receive-only mode, when the NEN input pin is set to logical “low” and NRM input pin is set to logical “low”. Normal-operating mode can only be entered when all supplies are available: • The transmitter supply VCC is available (VCC > VCC(UV,R)). 6.2 Receive-only mode In Receive-only mode the transmitter is disabled and the receiver is enabled. The TLE9250 can receive data from the bus, but cannot send any message (see also Figure 4 and Table 5): • The transmitter is disabled and the data available on the TxD input is blocked. • The normal-mode receiver is enabled. • The RxD output pin indicates the data received by the normal-mode receiver. • The bus biasing is connected to VCC/2. • The NEN and NRM input pins are active and change the mode of operation to Normal-operating mode or Power-save mode. • The TxD time-out function is disabled. • The overtemperature protection is disabled. • The undervoltage detection on VCC is active and powers down the device in case of detection. • Receive-only mode can only be entered when VCC (VCC > VCC(UV,R)) is available. 6.3 Power-save mode In Power-save mode the transmitter and receiver are disabled. (see also Figure 4 and Table 5): • The transmitter is disabled and the data available on the TxD input is blocked. • The receiver is disabled and the data available on the bus is blocked. • The RxD output pin is permanently set to logical “high”. • The bus biasing is floating. • The NEN and NRM input pins are active and change the mode of operation to Normal-operating mode or Receive-only mode. • The overtemperature protection is disabled. Datasheet 11 Rev. 1.11 2019-09-19 High Speed CAN FD Transceiver TLE9250 Modes of operation • The undervoltage detection on VCC is enabled and powers down the device in case of detection. 6.4 Power-down state Independent of the status at NRM and NEN input pins the TLE9250 is powered down if the supply voltage VCC < VCC(UV,F) (see Figure 4). In the power-down state the differential input resistors of the receiver are switched off. The CANH and CANL bus interface of the TLE9250 is floating and acts as a high-impedance input with a very small leakage current. The high-ohmic input does not influence the recessive level of the CAN network and allows an optimized EME performance of the entire HS CAN network. In power-down state the transceiver is an invisible node to the bus. Datasheet 12 Rev. 1.11 2019-09-19 High Speed CAN FD Transceiver TLE9250 Changing the mode of operation 7 Changing the mode of operation 7.1 Power-up and power-down The HS CAN transceiver TLE9250 powers up by applying the supply voltage VCC to the device (VCC > VCC(U,R)). After powering up, the device enters one out of three operating modes (see Figure 5 and Figure 6). Depending on the condition of the mode selection pin NEN and NRM the device can enter every mode of operation after the power-up: • The NEN input is set to “low” and NRM input is set to “high” - Normal-operating mode • The NEN input is set to “high” - Power-save mode • The NEN input is set to “low” and NRM input is set to “low” - Receive-only mode The device TLE9250 powers down when the VCC supply falls below the undervoltage detection threshold (VCC < VCC(U,F)). The power-down detection is active in every mode of operation. Normal-operating mode VCC “on” NRM “1” NEN “0” NEN NRM 0 VCC “off” 1 NEN NRM “X” “X” Receive-only mode VCC NEN NRM VCC “off” “off” VCC “on” NEN “1” Power-save mode VCC “off” NEN NRM 1 Figure 5 “on” VCC “on” NRM “0” NEN “0” Power-down state VCC “off” VCC “X” VCC 0 “0” VCC “on” “blue” -> indicates the event triggering the power-up or power-down “red” -> indicates the condition which is required to reach a certain operating mode “on” Power-up and power-down VCC tPOFF VCC undervoltage monitor VCC(UV,F) hysteresis VCC(UV,H) VCC undervoltage monitor VCC(UV,R) tPON t any mode of operation Power-down state Power-save mode “X” = don’t care “high” due the internal pull-up resistor1) NEN "0" for Normal-operating mode "1" for Power-save mode t NRM "1" for Normal-operating mode "0" for Receive-only mode 1) Figure 6 Datasheet “X” = don’t care “high” due the internal pull-up resistor1) t assuming no external signal applied Power-up and power-down timings 13 Rev. 1.11 2019-09-19 High Speed CAN FD Transceiver TLE9250 Changing the mode of operation 7.2 Mode change by the NEN and NRM pins When the TLE9250 is supplied with the digital voltage VCC the internal logic works and mode change by the mode selection pins NEN and NRM is possible. By default the NRM input pin and the NEN input pin are logical “high” due to the internal pull-up current source to VCC. Changing the NEN input pin to logical “low” in Power-save mode triggers a mode change to Normal-operating mode (see Figure 7). To enter Normal-operating mode the NRM input pin has to be logical “high” and the transmitter supply VCC needs to be available. Receive-only mode can be entered from Normal-operating mode and Power-save mode by setting the NRM pin to logical “low”. To enter Receive-only mode the NEN input pin and the NRM input pin has to be logical “low” and the transmitter supply VCC needs to be available. The device remains in Power-save mode independently of state of the NRM input pin. Normal-operating mode NEN NRM 0 1 NEN NRM “X” “X” “on” NEN “0” NRM “1” Power-down state NEN “0” NRM “1” VCC VCC NEN “0” NRM “0” Receive-only mode NEN NRM “off” 0 NEN “1” NRM “X” 0 VCC “on” NEN “1” NRM “X” Power-save mode NEN NRM 1 Figure 7 Datasheet “X” NEN “0” NRM “0” VCC “on” Mode selection by the NEN and NRM pins 14 Rev. 1.11 2019-09-19 High Speed CAN FD Transceiver TLE9250 Fail safe functions 8 Fail safe functions 8.1 Short circuit protection The CANH and CANL bus pins are proven to cope with a short circuit fault against GND and against the supply voltages. A current limiting circuit protects the transceiver against damages. If the device is heating up due to a continuous short on the CANH or CANL, the internal overtemperature protection switches off the bus transmitter. 8.2 Unconnected logic pins All logic input pins have an internal pull-up current source to VCC. In case the VCC supply is activated and the logical pins are open, the TLE9250 enters into the Power-save mode by default. 8.3 TxD time-out function The TxD time-out feature protects the CAN bus against permanent blocking in case the logical signal on the TxD pin is continuously “low”. A continuous “low” signal on the TxD pin might have its root cause in a lockedup microcontroller or in a short circuit on the printed circuit board, for example. In Normal-operating mode, a logical “low” signal on the TxD pin for the time t > tTxD enables the TxD time-out feature and the TLE9250 disables the transmitter (see Figure 8). The receiver is still active and the data on the bus continues to be monitored by the RxD output pin. TxD t t > tTxD TxD time-out CANH CANL TxD time–out released t RxD t Figure 8 TxD time-out function Figure 8 illustrates how the transmitter is deactivated and activated again. A permanent “low” signal on the TxD input pin activates the TxD time-out function and deactivates the transmitter. To release the transmitter after a TxD time-out event, the TLE9250 requires a signal change on the TxD input pin from logical “low” to logical “high”. 8.4 Overtemperature protection The TLE9250 has an integrated overtemperature detection to protect the TLE9250 against thermal overstress of the transmitter. The overtemperature protection is only active in Normal-operating mode. In case of an Datasheet 15 Rev. 1.11 2019-09-19 High Speed CAN FD Transceiver TLE9250 Fail safe functions overtemperature condition, the temperature sensor will disable the transmitter while the transceiver remains in Normal-operating mode. After the device has cooled down the transmitter is activated again (see Figure 9). A hysteresis is implemented within the temperature sensor. TJSD (shut down temperature) TJ cool down ΔT switch-on transmitter t CANH CANL t TxD t RxD t Figure 9 8.5 Overtemperature proctection Delay time for mode change The HS CAN transceiver TLE9250 changes the mode of operation within the time window tMode. During the mode change from Power-save mode to non-low power mode the RxD output pin is permanently set to logical “high” and does not reflect the status on the CANH and CANL input pins. After the mode change is completed, the transceiver TLE9250 releases the RxD output pin. Datasheet 16 Rev. 1.11 2019-09-19 High Speed CAN FD Transceiver TLE9250 Electrical characteristics 9 Electrical characteristics 9.1 Functional device characteristics Table 6 Electrical characteristics 4.5 V < VCC < 5.5 V; RL = 60 Ω; -40 °C < Tj < 150 °C; all voltages with respect to ground; positive current flowing into pin; unless otherwise specified. Parameter Symbol Values Min. Typ. Max. Unit Note or Test Condition Number Current Consumption Current consumption at VCC Normal-operating, recessive state ICC_R – 2 4 mA VTxD = VCC; VNEN = 0 V; VNRM = VCC; VDiff = 0 V; P_9.1.1 Current consumption at VCC Normal-operating mode, dominant state ICC_D – 38 48 mA VTxD = VNEN = 0 V; VNRM = VCC; P_9.1.2 Current consumption at VCC Power-save mode ICC(PSM) – 5 17 µA VTxD = VNEN = VCC; P_9.1.4 Current consumption at VCC Receive-only mode ICC(ROM) 2.5 mA VNRM = VNEN = 0 V; VCC,UV < VCC < 5.5 V; P_9.1.8 Supply resets VCC undervoltage monitor rising edge VCC(UV,R) 3.8 4.35 4.5 V – P_9.1.12 VCC undervoltage monitor falling edge VCC(UV,F) 3.8 4.25 4.5 V – P_9.1.13 VCC undervoltage monitor hysteresis VCC(UV,H) – 100 – mV 1) P_9.1.14 VCC delay time power-up tPON – – 280 µs 1) (see Figure 6); P_9.1.19 tPOFF – – 100 µs 1) (see Figure 6); P_9.1.20 “High” level output current IRxD,H – -4 -1 mA VRxD = VCC - 0.4 V; VDiff < 0.5 V; P_9.1.21 “Low” level output current IRxD,L 1 4 – mA VRxD = 0.4 V; VDiff > 0.9 V; P_9.1.22 “High” level input voltage threshold VTxD,H – 0.5 × VCC 0.7 × VCC V recessive state; P_9.1.26 “Low” level input voltage threshold VTxD,L 0.3 × VCC 0.4 × VCC – V dominant state; P_9.1.27 Input hysteresis VHYS(TxD) – 200 – mV 1) P_9.1.28 “High” level input current ITxD,H -2 – 2 µA VTxD = VCC; P_9.1.29 VCC delay time power-down Receiver output RxD Transmission input TxD Datasheet 17 Rev. 1.11 2019-09-19 High Speed CAN FD Transceiver TLE9250 Electrical characteristics Table 6 Electrical characteristics (cont’d) 4.5 V < VCC < 5.5 V; RL = 60 Ω; -40 °C < Tj < 150 °C; all voltages with respect to ground; positive current flowing into pin; unless otherwise specified. Parameter Symbol Values Min. Typ. Max. Unit Note or Test Condition VTxD 1) = 0 V; Number P_9.1.30 “Low” level input current ITxD,L -200 – -20 µA Input capacitance CTxD – – 10 pF TxD permanent dominant time-out, optional tTxD 1 – 4 ms Normal-operating mode; P_9.1.32 P_9.1.31 NRM and NEN input “High” level input voltage threshold VNRM,H/NEN,H – 0.5 × VCC 0.7 × VCC V Power-save mode; P_9.1.36 “Low” level input voltage threshold VNRM,L/NEN,L 0.3 × VCC 0.4 × VCC – V Normal-operating mode; P_9.1.37 “High” level input current INRM,H/NEN,H -2 – 2 µA VNRM/NEN = VCC; P_9.1.38 “Low” level input current INRM,L/NEN,L – -20 µA VNRM/NEN = 0 V; P_9.1.39 Input hysteresis VHYS(NRM)(NE – 200 – mV 1) P_9.1.42 – 10 pF 1) P_9.1.43 -200 N) Input capacitance C(NRM)(NEN) – Bus receiver Differential range dominant Normal-operating mode VDiff_D_Range 0.9 – 8.0 V -12 V ≤ VCMR ≤ 12 V; P_9.1.46 Differential range recessive Normal-operating mode VDiff_R_Range -3.0 – 0.5 V -12 V ≤ VCMR ≤ 12 V; P_9.1.48 mV 1) P_9.1.49 Differential receiver hysteresis VDiff,hys Normal-operating mode 30 Common mode range CMR -12 – 12 V – P_9.1.52 Single ended internal resistance RCAN_H, RCAN_L 6 – 50 kΩ recessive state; -2 V ≤ VCANH ≤ 7 V; -2 V ≤ VCANL ≤ 7 V; P_9.1.53 Differential internal resistance RDiff 12 – 100 kΩ recessive state; -2 V ≤ VCANH ≤ 7 V; -2 V ≤ VCANL ≤ 7 V; P_9.1.54 Input resistance deviation between CANH and CANL ∆Ri -3 – 3 % 1) recessive state; VCANH = VCANL = 5 V; P_9.1.55 Input capacitance CANH, CANL versus GND CIn – 20 40 pF 2) recessive state P_9.1.56 – 10 20 pF 2) recessive state P_9.1.57 2.0 2.5 3.0 V VTxD = VCC; no load; Differential input capacitance CInDiff Bus transmitter CANL, CANH recessive output voltage Normal-operating mode Datasheet VCANL,H 18 P_9.1.58 Rev. 1.11 2019-09-19 High Speed CAN FD Transceiver TLE9250 Electrical characteristics Table 6 Electrical characteristics (cont’d) 4.5 V < VCC < 5.5 V; RL = 60 Ω; -40 °C < Tj < 150 °C; all voltages with respect to ground; positive current flowing into pin; unless otherwise specified. Parameter Symbol Values Min. Typ. Max. Unit Note or Test Condition Number CANH, CANL recessive output voltage difference Normal-operating mode VDiff_R_NM = -50 VCANH VCANL – 50 mV VTxD = VCC; no load; P_9.1.59 CANL dominant output voltage Normal-operating mode VCANL 0.5 – 2.25 V VTxD = 0 V; 50 Ω < RL < 65 Ω; 4.75 V < VCC < 5.25 V; P_9.1.60 CANH dominant output voltage Normal-operating mode VCANH 2.75 – 4.5 V VTxD = 0 V; 50 Ω < RL < 65 Ω; 4.75 V < VCC < 5.25 V; P_9.1.61 Differential voltage dominant VDiff_D_NM Normal-operating mode VDiff = VCANH - VCANL 1.5 2.0 2.5 V VTxD = 0 V; 50 Ω < RL < 65 Ω; 4.75 V < VCC < 5.25 V; P_9.1.62 Differential voltage dominant VDiff_EXT_BL extended bus load Normal-operating mode 1.4 2.0 3.3 V VTxD = 0 V; 45 Ω < RL < 70 Ω; 4.75 V < VCC < 5.25 V; P_9.1.63 – 5.0 V VTxD = 0 V; RL = 2240 Ω; 4.75 V < VCC < 5.25 V; static behavior;1) P_9.1.64 P_9.1.67 Differential voltage dominant VDiff_HEXT_BL 1.5 high extended bus load Normal-operating mode Driver symmetry (VSYM = VCANH + VCANL) VSYM 0.9 × VCC 1.0 × VCC 1.1 × VCC V 1) 3) CANL short circuit current ICANLsc 40 75 115 mA VCANLshort = 18 V; t < tTxD; VTxD = 0 V; P_9.1.68 CANH short circuit current ICANHsc -115 -75 -40 mA VCANHshort = -3 V; t < tTxD; VTxD = 0 V; P_9.1.70 Leakage current, CANH ICANH,lk -5 – 5 µA VCC = 0 V; 0 V < VCANH ≤ 5 V; VCANH = VCANL; P_9.1.71 Leakage current, CANL ICANL,lk -5 – 5 µA VCC = 0 V; 0 V < VCANL ≤ 5 V; VCANH = VCANL; P_9.1.72 CANH, CANL output voltage difference slope, recessive to dominant Vdiff_slope_rd – – 70 V/µs 1) P_9.1.190 Datasheet 19 C1 = 4.7 nF; 30 % to 70 % of measured differential bus voltage; C2 = 100 pF; RL = 60 Ω; 4.75 V < VCC < 5.25 V; Rev. 1.11 2019-09-19 High Speed CAN FD Transceiver TLE9250 Electrical characteristics Table 6 Electrical characteristics (cont’d) 4.5 V < VCC < 5.5 V; RL = 60 Ω; -40 °C < Tj < 150 °C; all voltages with respect to ground; positive current flowing into pin; unless otherwise specified. Parameter Symbol Values Min. Vdiff_slope_dr – CANH, CANL output voltage difference slope, dominant to recessive Typ. Max. Unit Note or Test Condition Number – 70 V/µs 1) 70 % to 30 % of measured differential bus voltage; C2 = 100 pF; RL = 60 Ω; 4.75 V < VCC < 5.25 V; P_9.1.191 Dynamic CAN-transceiver characteristics Propagation delay TxD-to-RxD tLoop 80 – 215 ns C1 = 0 pF; C2 = 100 pF; CRxD = 15 pF; (see Figure 10) P_9.1.73 Propagation delay increased load TxD-to-RxD tLoop_150 80 – 330 ns 1) C1 = 0 pF; C2 = 100 pF; CRxD = 15 pF; RL = 150 Ω; P_9.1.74 tMode – – 20 µs 1) P_9.1.79 Received recessive bit width at 2 MBit/s tBit(RxD)_2M 400 500 550 ns C2 = 100 pF; CRxD = 15 pF; tBit = 500 ns; (see Figure 11); P_9.1.84 Received recessive bit width at 5 MBit/s tBit(RxD)_5M 120 200 220 ns C2 = 100 pF; CRxD = 15 pF; tBit = 200 ns; (see Figure 11); P_9.1.85 Transmitted recessive bit width at 2 MBit/s tBit(Bus)_2M 435 500 530 ns C2 = 100 pF; CRxD = 15 pF; tBit = 500 ns; (see Figure 11); P_9.1.86 Transmitted recessive bit width at 5 MBit/s tBit(Bus)_5M 155 200 210 ns C2 = 100 pF; CRxD = 15 pF; tBit = 200 ns; (see Figure 11); P_9.1.87 Receiver timing symmetry at ∆tRec_2M 2 MBit/s ∆tRec_2M = tBit(RxD)_2M - tBit(Bus)_2M -65 – 40 ns C2 = 100 pF; CRxD = 15 pF; tBit = 500 ns; (see Figure 11); P_9.1.88 Receiver timing symmetry at ∆tRec_5M 5 MBit/s ∆tRec_5M = tBit(RxD)_5M - tBit(Bus)_5M -45 – 15 ns C2 = 100 pF; CRxD = 15 pF; tBit = 200 ns; (see Figure 11); P_9.1.89 Delay Times Delay time for mode change CAN FD characteristics Datasheet 20 Rev. 1.11 2019-09-19 High Speed CAN FD Transceiver TLE9250 Electrical characteristics 1) Not subject to production test, specified by design 2) Not subject to production test, specified by design, S2P-Method; f = 10 MHz 3) VSYM shall be observed during dominant and recessive state and also during the transition from dominant to recessive and vice versa, while TxD is stimulated by a square wave signal with a frequency of 1 MHz. Datasheet 21 Rev. 1.11 2019-09-19 High Speed CAN FD Transceiver TLE9250 Electrical characteristics 9.2 Diagrams TxD 0.7 x VCC 0.3 x VCC t VDiff t tLoop(H,L) tLoop(L,H) RxD 0.7 x VCC 0.3 x VCC t Figure 10 Timing diagrams for dynamic characteristics TxD 0.7 x VCC 0.3 x VCC 0.3 x VCC 5 x tBit VDiff tBit t tLoop(H,L) tBit(Bus) VDiff = VCANH - VCANL 0.9 V 0.5 V t tLoop(L,H) tBit(RxD) RxD 0.7 x VCC 0.3 x VCC t Figure 11 Datasheet Recessive bit time for five dominant bits followed by one recessive bit 22 Rev. 1.11 2019-09-19 High Speed CAN FD Transceiver TLE9250 Application information 10 Application information 10.1 ESD robustness according to IEC61000-4-2 Tests for ESD robustness according to IEC61000-4-2 “Gun test” (150 pF, 330 Ω) have been performed. The results and test conditions are available in a separate test report. Table 7 ESD robustness according to IEC61000-4-2 Performed Test Result Electrostatic discharge voltage at pin CANH and CANL versus GND ≥ +11 Electrostatic discharge voltage at pin CANH and CANL versus GND ≤ -11 Unit Remarks kV 1) Positive pulse kV 1) Negative pulse 1) Not subject to production test. ESD susceptibility “ESD GUN” according to GIFT / ICT paper: “EMC Evaluation of CAN Transceivers, version IEC TS62228”, section 4.3. (DIN EN61000-4-2) Tested by external test facility (IBEE Zwickau, EMC test report Nr. 01-07-2017 and Nr. 06-08-17) 10.2 Application example VBAT I Q1 22 μF TLS850B0ELV50 CANH CANL EN 100 nF GND 3 VCC 120 Ohm TLE9250 7 6 optional: common mode choke NEN CANH TxD RxD CANL NRM 8 1 Out Out 4 5 In VCC Microcontroller e.g. XC22xx Out GND GND 2 I Q1 22 μF TLS850B0ELV50 EN 100 nF GND 3 VCC TLE9250 7 6 NEN CANH TxD RxD CANL optional: common mode choke 120 Ohm CANH NRM 8 1 4 5 Out Out In VCC Microcontroller e.g. XC22xx Out GND GND 2 CANL example ECU design Figure 12 Datasheet Application circuit 23 Rev. 1.11 2019-09-19 High Speed CAN FD Transceiver TLE9250 Application information VBAT I Q1 22 μF TLE4476D CANH CANL GND EN 100 nF 100 nF Q2 3 VCC 22 μF 120 Ohm VIO TLE9250V 7 6 optional: common mode choke NEN CANH TxD RxD CANL 100 nF 5 8 Out 1 Out 4 In VCC Microcontroller e.g. XC22xx GND GND 2 I Q1 22 μF TLE4476D EN GND 100 nF Q2 3 VCC 22 μF VIO TLE9250V 7 6 NEN CANH TxD RxD CANL optional: common mode choke 120 Ohm CANH Figure 13 10.3 • CANL 5 8 1 4 100 nF 100 nF Out Out In VCC Microcontroller e.g. XC22xx GND GND 2 example ECU design Application circuit Further application information For further information you may visit: http://www.infineon.com/automotive-transceiver Datasheet 24 Rev. 1.11 2019-09-19 High Speed CAN FD Transceiver TLE9250 Package outline 11 Package outline Figure 14 PG-TSON-8 (Plastic Thin Small Outline Nonleaded) Figure 15 PG-DSO-8 (Plastic Dual Small Outline) Green product (RoHS compliant) To meet the world-wide customer requirements for environmentally friendly products and to be compliant with government regulations the device is available as a green product. Green products are RoHS compliant (i.e. Pb-free finish on leads and suitable for Pb-free soldering according to IPC/JEDEC J-STD-020). For further information on alternative packages, please visit our website: http://www.infineon.com/packages. Datasheet 25 Dimensions in mm Rev. 1.11 2019-09-19 High Speed CAN FD Transceiver TLE9250 Revision history 12 Revision history Revision Date Changes 1.11 2019-09-19 Datasheet updated: • Editorial changes • Updated bus transmitter table – added P_9.1.190 and P_ 9.1.191 (no product change) – tightened P_9.1.59 and P_9.1.62 – tightened P_9.1.56 and P_9.1.57 by additional footnote • Updated dynamic CAN-transceiver characteristics table – tightened P_9.1.73 1.1 1.0 Datasheet 2018-05-23 2017-09-14 Datasheet updated: • ICC_D max. lowered from 60mA to 48mA (see P_9.1.2) • ICC_(PSM) max. lowered from 20µA to 17µA (see P_9.1.4) • Extended temperature condition TJ < 150°C and added typical value: 5µA (see P_9.1.4) • Corrected description for NEN and NRM pin in Table 5 • Removed description of bus wake-up capability in Chapter 5 • Updated Figure 10. Removed unspecified parameters td(L),T, td(L),R, td(H),T, td(H),R. • Editorial Changes Datasheet created 26 Rev. 1.11 2019-09-19 Trademarks All referenced product or service names and trademarks are the property of their respective owners. Edition 2019-09-19 Published by Infineon Technologies AG 81726 Munich, Germany © 2019 Infineon Technologies AG. All Rights Reserved. Do you have a question about any aspect of this document? Email: erratum@infineon.com Document reference Z8F53400820 IMPORTANT NOTICE The information given in this document shall in no event be regarded as a guarantee of conditions or characteristics ("Beschaffenheitsgarantie"). With respect to any examples, hints or any typical values stated herein and/or any information regarding the application of the product, Infineon Technologies hereby disclaims any and all warranties and liabilities of any kind, including without limitation warranties of non-infringement of intellectual property rights of any third party. In addition, any information given in this document is subject to customer's compliance with its obligations stated in this document and any applicable legal requirements, norms and standards concerning customer's products and any use of the product of Infineon Technologies in customer's applications. The data contained in this document is exclusively intended for technically trained staff. It is the responsibility of customer's technical departments to evaluate the suitability of the product for the intended application and the completeness of the product information given in this document with respect to such application. For further information on technology, delivery terms and conditions and prices, please contact the nearest Infineon Technologies Office (www.infineon.com). WARNINGS Due to technical requirements products may contain dangerous substances. For information on the types in question please contact your nearest Infineon Technologies office. Except as otherwise explicitly approved by Infineon Technologies in a written document signed by authorized representatives of Infineon Technologies, Infineon Technologies’ products may not be used in any applications where a failure of the product or any consequences of the use thereof can reasonably be expected to result in personal injury.