EUP8051-42MIR1

EUP8051 Low Cost 1A Linear Battery Charge Controllers DESCRIPTION The EUP8051 is a single Lithium-Ion (Li-Ion) and Lithium–Polymer (Li-Pol) linear charge management controller for use in cost sensitive and portable applications. It combines high accuracy constant-current and constant-voltage regulation, cell preconditioning, temperature monitoring, automatic charge termination, charge-status indication, in a space-saving MSOP-8 package. The EUP8051 applies a constant current up to 1A to the battery and the charge current can be programmed externally with a sense-resistor. The EUP8051 automatically terminates the charge cycle when the charge current drops to the charge termination threshold (ITERM) after the charge-regulation voltage is reached. When the input supply is removed, the EUP8051 automatically enters a low-power sleep mode, dropping the battery drain current to less than 1µA. A battery charge state output pin is provided to indicate battery charge status through a display LED. The battery charge status output is a serial interface which may also be read by a system microcontroller. FEATURES Programmable Charge Current up to 1A 4.5V-7V Input Voltage Range Ideal for Single Cell (4.1V or 4.2V) Li-Ion or Li-Pol Batteries Preset Charge Voltage with ±1% Accuracy Constant-Current/Constant Voltage Operation Preconditioning of Low Voltage Cells Optional Cell-Temperature Monitoring Before and During Charge Charge Status Indication Automatic Battery Recharge Charge Termination by Minimum Current Automatic Low-Power Sleep Mode When Input Power is Removed Available in MSOP-8,TSSOP-8 and SOP-8 Package RoHS Compliant and 100% Lead (Pb)-Free APPLICATIONS Cellular Phones / PDAs/ MP3 Players/DSC Handheld Instruments DS8051 Ver 1.6 Sep. 2006 1 EUP8051 Typical Application Circuit DS8051 Ver 1.6 Sep. 2006 2 EUP8051 Pin Configurations Part Number Pin Configurations EUP8051 MSOP-8 EUP8051 TSSOP-8 EUP8051 SOP-8 Pin Description PIN VCC TS STAT VSS CC FB/CE SNS BAT MSOP-8 1 2 3 4 5 6 7 8 TSSOP-8 3 4 5 6 7 8 1 2 SOP-8 1 2 3 4 5 6 7 8 O I I I I/O I I O DESCRIPTION Supply Voltage Input Temperature Sense Input Charge Status Output Ground Charge Control Output External Feedback input or Charge Enable Function. Input from controller or finely adjust the battery regulated voltage with external voltage divider Current Sense Input Battery Voltage Input DS8051 Ver 1.6 Sep. 2006 3 EUP8051 Ordering Information Order Number EUP8051-41MIR1 EUP8051-42MIR1 EUP8051-42QIR1 Package Type MSOP-8 MSOP-8 TSSOP-8 Marking xxxx 8051 xxxx 8051C xxxx 8051N xxxx EUP8051 N Operating Temperature range -20 °C to 70°C -20 °C to 70°C -20 °C to 70°C EUP8051-42DIR1 SOP-8 -20 °C to 70°C EUP8051-□ □ □ □ □ □ Lead Free Code 1: Lead Free 0: Lead Packing R: Tape& Reel Operating temperature range I: Industry Standard Package Type M: MSOP Q: TSSOP D: SOP Output Voltage 41: 4.1V 42: 4.2V DS8051 Ver 1.6 Sep. 2006 4 EUP8051 Absolute Maximum Ratings Supply voltage, (Vcc with respect to GND) ------------------------------------------------------ -0.3 to +7V Input voltage, SNS, BAT, TS, PI (all with respect to GND)-------------------------- -0.3V to VCC +0.3V Sink current (STAT pin) not to exceed PD -------------------------------------------------------------- 20mA Source current (STAT pin) not to exceed PD ---------------------------------------------------------- 10mA Output current (CC pin) not to exceed PD -------------------------------------------------------------- 40mA Maximum Junction Temperature, TJ ------------------------------------------------------------------- 150°C Storage temperature range, Tstg ------------------------------------------------------------- -65°C to 150°C Lead temperature (soldering, 10s) -----------------------------------------------------------------300°C Package Thermal Resistance, θJA- MSOP8 ---------------------------------------------------------- 80°C/W Recommended Operating Conditions Min. Supply voltage, VCC Operating free-air temperature range, TA 4.5 -20 Max. 7 70 Unit V °C Electrical Characteristics over Recommended Operating Free-Air Temperature Range EUP8051 Symbol Parameter Conditions Min. Typ. Max. I(VCC) I(VCCS) IIB(BAT) IIB(SNS) IIB(TS) IIB(PI) VCC current VCC Sleep current Input bias current on BAT pin Input bias current on SNS pin Input bias current on TS pin Input bias current on PI pin VCC=5V >VCC(min), Excluding external loads V(BAT) ≥ V(min), V(BAT)-VCC ≥ 0.8V V(BAT)=V(REG) V(SNS)=5V V(TS)=5V V(PI)=5V EUP8051-4.1 EUP8051-4.2 4.059 4.158 4.10 4.20 0.6 2 1 6 1 1 1 1 4.141 4.242 Unit mA µA µA µA µA µA Battery Voltage Regulation VO(REG) Output voltage V DS8051 Ver 1.6 Sep. 2006 5 EUP8051 Electrical Characteristics Over Recommended Operating Free-Air Temperature Range Symbol V(SNS) Parameter Conditions EUP8051 Unit Min. Typ. Max. 198 220 242 mV Current regulation threshold Voltage at pin SNS, relative to VCC Charge Termination Detection I(TERM) Charge termination current Voltage at pin SNS, relative to VCC detect threshold 0°C ≤ TA ≤ 50°C 5 15 25 mV Temperature Comparator V(TS1) V(TS2) Lower temperature threshold Upper temperature threshold TS pin voltage 29 58 2.94 3.04 30 60 3 3.1 31 62 3.06 3.16 %VCC Precharge Comparator V(min) Precharge threshold EUP8051-4.1 EUP8051-4.2 V Precharge Current Regulation Voltage at pin SNS, relative to VCC 0°C ≤ TA ≤ 50°C Voltage at pin SNS, relative to VCC 0°C ≤ TA ≤ 50°C , VCC=5V 5 15 15 25 mV mV I(PRECHG) Precharge current regulation VRCH comparator(Battery Recharge Threshold) V(RCH) Recharge threshold EUP8051-4.1 and EUP8051-4.2 VO(REG)- VO(REG)- VO(REG)98mV 100mV 102mV 0.5 VCC-0.5 1.5 5 40 V STAT Pin VOL(STAT) VOH(STAT) CC Pin VOL(CC) IO(CC) Output low voltage Sink current IO(CC)=5mA(sink) Not to exceed power rating specification(PD) V mA Output(low)voltage Output(high)voltage IOL=10mA IOH=5mA V DS8051 Ver 1.6 Sep. 2006 6 EUP8051 Typical Operating Characteristics Battery Voltage Regulation vs. Temperature 4.40 4.35 4.30 4.25 Battery Recharge Threshold vs. Temperature Battery Recharge Threshold(V) Battery Voltage Regulation(V) 4.30 4.25 4.20 4.15 4.10 4.05 4.00 -20 0 20 o 4.20 4.15 4.10 4.05 4.00 3.95 3.90 40 60 80 -20 0 20 o 40 60 80 Temperature( C) Temperature( C) Precharge Threshold vs. Temperature 3.30 3.25 Current Regulation vs. Temperature 1300 1200 Precharge Threshold(V) 3.15 3.10 3.05 3.00 2.95 2.90 -20 0 20 o Current Regulation(mA) 40 60 80 3.20 1100 1000 900 800 -20 0 20 o 40 60 80 Temperature( C) Temperature( C) Precharge Threshold vs. Temperature 4.40 140 Battery Voltage Regulation vs. Supply Voltage 4.35 Battery Voltage Regulation(V) -20 0 20 o Precharge Threshold(mA) 4.30 4.25 4.20 4.15 4.10 4.05 4.00 4.5 5.0 5.5 6.0 6.5 7.0 120 100 80 60 40 60 80 Temperature( C) Supply Voltage(V) DS8051 Ver 1.6 Sep. 2006 7 EUP8051 Current Regulation vs. Supply Voltage 1300 Precharge Threshold vs. Supply Voltage 140 1200 Precharge Threshold(mA) Current Regulation (mA) 120 1100 100 1000 80 900 60 800 4.5 5.0 5.5 6.0 6.5 4.5 5.0 5.5 6.0 Supply voltage(V) Supply Voltage(V) DS8051 Ver 1.6 Sep. 2006 8 EUP8051 Application Information Functional Description The EUP8051 is an advanced 1A linear charge controller for single Li-Ion of Li-Pol applications. Refer to Blocking Diagram (Figure3) and Operation Flow Chart (Figure4) in this section. DS8051 Ver 1.6 Sep. 2006 9 EUP8051 Power On Reset VCC Applied NO Sleep Mode YES Temperature Fault NO Temperature Test TS>VTS1 TS VBAT YES Low Current Conditioning Charge (Trickle Charge) NO Current Phase Test VREG>VBAT YES Constant Current Charging Mode NO Voltage Phase Test IBAT>ITERM YES Constant Voltage Charging Mode NO Charge Termination NO Recharge Test VRCH>VBAT YES Figure4. Operation Flow Chart DS8051 Ver 1.6 Sep. 2006 10 EUP8051 Qualification and Precharge When power is applied, the EUP8051 starts a charge-cycle if a battery is already present or when a battery is inserted. Charge qualification is based on battery temperature and voltage. The EUP8051 suspends charge if the battery temperature is outside the V(TS1) to V(TS2) range and suspends charge until the battery temperature is within the allowed range. The EUP8051 also checks the battery voltage. If the battery voltage is below the precharge threshold V(min), the EUP8051 uses precharge to condition the battery. The conditioning charge rate I(PRECHG) is set at approximately 10% of the regulation current. The conditioning current also minimizes heat dissipation in the external pass-element during the initial stage of charge. See Figure5 for a typical charge-profile. Voltage Regulation Phase The voltage regulation feedback is through the BAT pin. This input is tied directly to the positive side of the battery pack. The EUP8051 monitors the battery-pack voltage between the BAT and VSS pins. The EUP8051 is offered in two fixed-voltage versions:4.1V, 4.2V. FB/CE Pin Function This pin has two functions, one is to enable/disable the charge function, and the other is to finely adjust battery regulation voltage. Connect this pin to VDD to enable EUP8051, and connect to ground to disable it (Figure7). If this pin is connected to a voltage divider as shown in Figure8, it can be a 2.15V reference voltage to adjust the output regulation voltage as desired. Current Regulation Phase The EUP8051 regulates current while the battery-pack voltage is less than the regulation voltage, VO(REG). The EUP8051 monitors charge current at the SNS input by the voltage drop across a sense-resistor, RSNS, in series with the battery pack. In current sensing configuration (Figure6), RSNS is between the VCC and SNS pins, charge-current feedback, applied through pin SNS, maintains a voltage of V(SNS) across the current sense resistor. The following formula calculates the value of the sense resistor: R SNS = V (SNS) I O(REG) ---------------------------- (1) Where IO(REG) is the desired charging current. Example: For 0.55A, RSNS: 0.22V/0.55A: 0.4Ω For 1.0A, RSNS: 0.22V/1.0A: 0.22Ω DS8051 Ver 1.6 Sep. 2006 11 EUP8051 For PTC Thermistors = 5× R 3 × (R TH TH ×R -R TC TC ) R T1 ---------------------- (5) R T2 = ×R TH TC [(2 × (R ) - (7 × R )] TH TC 5× R ------------- (6) V = 2.15 × (1 + FB1 )V O(REG) R FB2 R Where R(TC) is the cold temperature resistance and R(TH) is the hot temperature resistance of thermistor, as specified by the thermistor manufacturer. RT1 or RT2 can be omitted if only one temperature (hot or cold) setting is required. Applying a voltage between the V(TS1) and V(TS2) thresholds to pin TS disables the temperature-sensing feature. Charge Termination and Recharge The EUP8051 monitors the charging current during the voltage-regulation phase. The EUP8051 declares a done condition and terminates charge when the current drops to the charge termination threshold, I(TERM). A new charge cycle begins when the battery voltage falls below the V(RCH) threshold. Battery Temperature Monitoring The EUP8051 continuously monitors temperature by measuring the voltage between the TS and VSS pins. A negative-or a positive-temperature coefficient thermistor (NTC, PTC) and an external voltage divider typically develop this voltage (See Figure9). The EUP8051 compares this voltage against its internal V(TS1) and V(TS2) thresholds to determine if charging is allowed. (See Figure10). The temperature sensing circuit is immune to any fluctuation in VCC, since both the external voltage divider and the internal thresholds (V(TS1) and V(TS2)) are referenced to VCC. The resistor values of R(T1) and R(T2) are calculated by the following equations: For NTC Thermistors R T1 = 5× R 3 × (R TH TC ×R -R TC ) ----------------------- (3) TH R T2 = ×R TH TC --------------- (4) [(2 × (R ) - (7 × R )] TH TC 5× R DS8051 Ver 1.6 Sep. 2006 12 EUP8051 Charge Inhibit Function The TS pin can be used as charge-inhibit input. The user can inhibit charge by connecting the TS pin to VCC or VSS (or any level outside the V(TS1) to V(TS2) thresholds). Applying a voltage between the V(TS1) and V(TS2) thresholds to pin TS returns the charger to normal operation. Charge Status Indication The EUP8051 reports the status of the charger on the 3-state STAT pin. The following table summarized the operation of the STAT pin. Condition Battery conditioning and charging Charge complete(done) Temperature fault or sleep mode STAT pin High Low Hi-Z Selecting Input Capacitor In most applications, all that is needed is high-frequency decoupling capacitor. A 0.1µF ceramic, placed in proximity to VCC and VSS pins, works well. The EUP8051 works with both regulated and unregulated external dc supplies. If a non-regulated supply is chosen, the supply unit should have enough capacitance to hold up the supply voltage to the minimum required input voltage at maximum load. If not, more capacitance must be added to the input of the charger. Selecting Output Capacitor The EUP8051 does not require any output capacitor for loop stability. In order to maintain good AC stability in the Constant Voltage mode, a minimum capacitance of 10µF is recommenced to bypass the VBAT pin to VSS. This capacitance provides compensation when there is no battery load. In addition, the battery and interconnections appear inductive at high frequencies. These elements are in the control feedback loop d＞uring Constant Voltage mode. Therefore, the bypass capacitance may be necessary to compensate for the inductive nature of the battery pack. Virtually any good quality output filter capacitor can be used, independent of the capacitor’s minimum ESR (Effective Series Resistance) value. The actual value of the capacitor and its associated ESR depends on the forward transconductance (gm) and capacitance of the external pass transistor. A 10µF tantalum or aluminum electrolytic capacitor at the output is usually sufficient to ensure stability for up to a 1A output current. Selecting An External Pass-Device (PMOS or PNP) The EUP8051 is designed to work with both P-channel MOSFET or PNP transistor. The device should be chosen to handle the required power dissipation, given the circuit parameters, PCB layout and heat sink configuration. The following examples illustrate the design process for PMOS device: P-Channel MOSFET Selection steps for a P-channel MOSFET: We will use the following conditions: VI=5V (with 10% supply tolerance); I(REG)=1A, 4.2-V single-cell Li-Ion. VI is the input voltage to the charger and I(REG) is the desired charge current. (See Figure2) The STAT pin can be used to drive a single LED (Figure1), dual-chip LEDs (Figure2) or for interface to a host or system processor (Figure11). When interfacing the EUP8051 to a processor, the user can use an output port, to recognize the high-Z state of the STAT pin. In this configuration, the user needs to read the input pin, toggle the output port and read the STAT pin again. In a high-Z condition, the input port always matches the signal level on the output port. Low-Power Sleep Mode When the input supply is disconnected, the charger automatically enters power-saving sleep mode. Only consuming an ultra-low 1µA in sleep mode, the EUP8051 minimizes battery drain when it is not charging. DS8051 Ver 1.6 Sep. 2006 13 EUP8051 1. Determine the maximum power dissipation, PD , in the transistor. The worst case power dissipation happens when the cell voltage, V(constant), is at its lowest (typically 3.1V at the beginning of current regulation phase) and VI is at its maximum. Where VD is the forward voltage drop across the reverse-blocking diode (if one is used), and VCS is the voltage drop across the current sense resistor. PD=(VI(MAX)－VD－VCS－VBAT)×IREG --------- (7) PD=(5.5－0.4－0.2－3.1)×1A PD=1.8W 2. Determine the package size needed in order to keep the junction temperature below the manufacturer’s recommended value, TJMAX. Calculate the total theta, θ(°C/W), needed. θ JA = = It is recommended to choose a package with a lower θJA than the number calculated above. 3. 4. 5. Select a drain-source voltage, V(DS), rating greater than the maximum input voltage. A 12V device will be adequate in this example. Select a device that has at least 50% higher drain current (ID) rating than the desired charge current I(REG). Verify that the available drive is large enough to supply the desired charge current. V(GS)=(VD+V(CS)+VOL(CC))－VI(min) -------------- (9) V(GS)=(0.4+0.2+1) － 4.5 V(GS)=-2.9 Where V(GS) is the gate-to-source voltage, VD is the forward voltage drop across the reverse-blocking diode (if one is used), and VCS is the voltage drop across the current sense resistor, and VOL(CC) is the CC pin output low voltage specification for the EUP8051. Select a MOSFET with gate threshold voltage, V(GSth), rating less than the calculated V(GS). Reverse Blocking Protection The optional reverse-blocking protection diode, depicted in Figure1&2 provides protection from a faulted or shorted input, or from a reversed-polarity input source. Without the protection diode, a faulted of shorted input would discharge the battery pack through the body diode of the external pass transistor. If a reverse-protection diode is incorporated in the design, it should be chosen to handle the fast charge current continuously at the maximum ambient temperature. In addition, the reverse-leakage current of the diode should be kept as small as possible. (T -T ) max(J) A(max) P D (150 - 40) 1.8 --------------(8) θ JA θJA = 61°C/W DS8051 Ver 1.6 Sep. 2006 14 EUP8051 Packaging Information 8-Pin MSOP NOTE 1. Package body sizes exclude mold flash and gate burrs 2. Dimension L is measured in gage plane 3. Tolerance 0.10mm unless otherwise specified 4. Controlling dimension is millimeter. Converted inch dimensions are not necessarily exact. SYMBOLS A A1 A2 b C D E E1 e L y θ DIMENSIONS IN MILLIMETERS MIN. NOM. MAX. 0.81 0.95 1.10 0.05 0.09 0.15 0.76 0.86 0.97 0.28 0.30 0.38 0.13 0.15 0.23 2.90 3.00 3.10 4.70 4.90 5.10 2.90 3.00 3.10 -----0.65 ----0.40 0.53 0.66 ----------0.10 0 -----6 DIMENSIONS IN INCHES MIN. NOM. MAX. 0.032 0.0375 0.043 0.002 0.004 0.006 0.030 0.034 0.038 0.011 0.012 0.015 0.005 0.006 0.009 0.114 0.118 0.122 0.185 0.193 0.201 0.114 0.118 0.122 -----0.026 -----0.016 0.021 0.026 ----------0.004 0 -----6 DS8051 Ver 1.6 Sep. 2006 15 EUP8051 8-Pin TSSOP NOTE 1. Package body sizes exclude mold flash protrusions or gate burrs 2. Tolerance ±0.10mm unless otherwise specified 3. Coplanarity: 0.1mm 4. Controlling dimension is millimeter. Converted inch dimensions are not necessarily exact. 5. Followed from JEDEC MO-153 SYMBOLS A A1 A2 b C D E E1 e L y θ DIMENSIONS IN MILLIMETERS MIN. NOM. MAX. ----------1.20 0.05 -----0.15 0.80 1.00 1.05 0.19 -----0.30 0.09 -----0.20 2.90 3.00 3.10 6.20 6.40 6.60 4.30 4.40 4.50 -----0.65 ----0.45 0.60 0.75 ----------0.10 0 -----8 DIMENSIONS IN INCHES MIN. NOM. MAX. ----------0.048 0.002 -----0.006 0.031 0.039 0.041 0.007 -----0.012 0.004 -----0.008 0.114 0.118 0.122 0.244 0.252 0.260 0.169 0.173 0.177 -----0.026 -----0.018 0.024 0.030 ----------0.004 0 -----8 DS8051 Ver 1.6 Sep. 2006 16 EUP8051 SOP-8 X Y Z Standard Solder Map Symbols A B C D E H F L1 L2 M N Dimension in Millimeters Min. Max. 4.80 5.00 5.80 6.20 3.80 4.00 1.194 1.346 1.45 1.55 0.00 0.10 0.33 0.51 0.19 0.25 0.40 1.27 0° 8° 40° 50° Dimension in Inches Min. Max. 0.189 0.197 0.228 0.244 0.150 0.157 0.047 0.053 0.057 0.061 0.000 0.004 0.013 0.020 0.007 0.010 0.016 0.050 0° 8° 40° 50° DS8051 Ver 1.6 Sep. 2006 17