12-22-BHR6C-A01-2C

Technical Data Sheet Right Angle Lens Chip LEDs with Bi-Color (Multi-Color) 12-22/BHR6C-A01/2C Features ․Package in 8mm tape on 7〞diameter reel. ․Compatible with automatic placement equipment. ․Compatible with infrared and vapor phase reflow solder process. ․Multi-color type. ․Pb-free. ․The product itself will remain within RoHS compliant version. Descriptions ․ The 12-22 SMD LED is much smaller than lead frame type components, thus enable smaller board size, higher packing density, reduced storage space and finally smaller equipment to be obtained. ․Besides, lightweight makes them ideal for miniature applications. etc. Applications ․Backlighting in dashboard and switch. ․Telecommunication: indicator and backlighting in telephone and fax. ․Flat backlight for LCD, switch and symbol. ․General use. Device Selection Guide Chip Type BH R6 Material InGaN AlGaInP Emitted Color Blue Brilliant Red Resin Color Water Clear Everlight Electronics Co., Ltd. Device No: DSE-0003879 http://www.everlight.com Prepared date:12-July.-2010 Rev: 4 Page: 1 of 11 Prepared by: Yang yuanyuan 12-22/BHR6C-A01/2C Package Outline Dimensions Note: The tolerances unless mentioned is ±0.1mm ,Unit = mm Everlight Electronics Co., Ltd. Device No: DSE-0003879 http://www.everlight.com Prepared date:12-July.-2010 Rev: 4 Page: 2 of 11 Prepared by: Yang yuanyuan 12-22/BHR6C-A01/2C Absolute Maximum Ratings (Ta=25℃) Parameter Reverse Voltage Forward Current Peak Forward Current (Duty 1/10 @1KHz) Power Dissipation Electrostatic Discharge(HBM) Operating Temperature Storage Temperature Soldering Temperature Symbol VR IF IFP Pd ESD Topr Tstg Tsol Rating 5 BH:25 R6:25 BH:100 R6:60 BH:95 R6:60 BH:150 R6:2000 -40 ~ +85 -40~ +90 Unit V mA mA mW V ℃ ℃ Reflow Soldering : 260 ℃ for 10 sec. Hand Soldering : 350 ℃ for 3 sec. Everlight Electronics Co., Ltd. Device No: DSE-0003879 http://www.everlight.com Prepared date:12-July.-2010 Rev: 4 Page: 3 of 11 Prepared by: Yang yuanyuan 12-22/BHR6C-A01/2C Electro-Optical Characteristics (Ta=25℃) Parameter Luminous Intensity Viewing Angle Peak Wavelength Symbol Iv BH R6 Min. 18.0 22.5 --------------- Typ. 28.0 30.0 120 468 632 470 624 35 25 ------------- Max. --------------------- Unit mcd deg nm Condition 2θ1/2 λp BH R6 Dominant Wavelength λd BH R6 nm IF=5mA Spectrum Radiation Bandwidth △λ BH ----R6 BH R6 ----3.1 2.2 50 10 nm Forward Voltage VF 2.7 1.7 ----- V Reverse Current IR BH R6 μA VR=5V Notes: 1.Tolerance of Luminous Intensity ±11% 2.Tolerance of Forward Voltage ±0.05V Everlight Electronics Co., Ltd. Device No: DSE-0003879 http://www.everlight.com Prepared date:12-July.-2010 Rev: 4 Page: 4 of 11 Prepared by: Yang yuanyuan 12-22/BHR6C-A01/2C Typical Electro-Optical Characteristics Curves BH Ta=25°C Relative luminous intensity ( % ) I (mA) Ta=25°C Wavelength λ(nm) Forward Current Forward Voltage VF (V) Ta=25°C Relative luminous intensity ( % ) Relative luminous intensity ( %) 0 20 40 60 80 100 Forward Current I (mA) 1000 100 10 1 -60 -40 -20 Ambient Temperature Ta(°C ) Forward Current I (mA) Ambient Temperature Ta (°C ) Everlight Electronics Co., Ltd. Device No: DSE-0003879 http://www.everlight.com Prepared date:12-July.-2010 Rev: 4 Page: 5 of 11 Prepared by: Yang yuanyuan 12-22/BHR6C-A01/2C Typical Electro-Optical Characteristics Curves R6 Ta=25°C Relative luminous intensity ( % ) I (mA) Ta=25°C Wavelength λ(nm) Forward Current Forward Voltage VF (V) Ta=25°C Relative luminous intensity ( % ) Relative luminous intensity ( %) Ambient Temperature Ta(°C ) Forward Current I (mA) Ta=25°C 0° 10° 20° 30° Forward Current I (mA) 40° 1.0 0.9 0.8 0.7 50° 60° 70° 80° 90° 0.5 0.3 0.1 0.2 0.4 0.6 Ambient Temperature Ta (°C ) Everlight Electronics Co., Ltd. Device No: DSE-0003879 http://www.everlight.com Prepared date:12-July.-2010 Rev: 4 Page: 6 of 11 Prepared by: Yang yuanyuan 12-22/BHR6C-A01/2C Label explanation CAT: Luminous Intensity Rank HUE: Dom. Wavelength Rank REF: Forward Voltage Rank Pb EVERLIGHT RoHS CPN : P N : XXXXXXXXXXXXX XXXXXXXXXXXXX QTY : XXX CAT : XXX HUE : XXX REF : XXX LOT NO : XXXXXXXXXX Reference : XXXXXXXX MADE IN TAIWAN Reel Dimensions Note: The tolerances unless mentioned is ±0.1mm ,Unit = mm Everlight Electronics Co., Ltd. Device No: DSE-0003879 http://www.everlight.com Prepared date:12-July.-2010 Rev: 4 Page: 7 of 11 Prepared by: Yang yuanyuan 12-22/BHR6C-A01/2C Carrier Tape Dimensions: Loaded quantity 2000 PCS per reel Polarity Note: The tolerances unless mentioned is ±0.1mm ,Unit = mm Moisture Resistant Packaging Label Aluminum moisture-proof bag Desiccant Label Everlight Electronics Co., Ltd. Device No: DSE-0003879 http://www.everlight.com Prepared date:12-July.-2010 Rev: 4 Page: 8 of 11 Prepared by: Yang yuanyuan 12-22/BHR6C-A01/2C Reliability Test Items And Conditions The reliability of products shall be satisfied with items listed below. Confidence level：90% LTPD：10% No. 1 2 Items Reflow Soldering Temperature Cycle Test Condition Temp. : 260℃±5℃ Min. 5sec. H : +100℃ 15min ∫ 5 min L : -40℃ 15min H : +100℃ 5min ∫ 10 sec L : -10℃ 5min Temp. : 100℃ Temp. : -40℃ IF = 20 mA 85℃/ 85%RH Test Sample Hours/Cycles Size 6 Min. 300 Cycles 22 PCS. 22 PCS. Ac/Re 0/1 0/1 3 4 5 6 7 Thermal Shock High Temperature Storage Low Temperature Storage DC Operating Life High Temperature / High Humidity 300 Cycles 1000 Hrs. 1000 Hrs. 1000 Hrs. 1000 Hrs. 22 PCS. 22 PCS. 22 PCS. 22 PCS. 22 PCS. 0/1 0/1 0/1 0/1 0/1 Everlight Electronics Co., Ltd. Device No: DSE-0003879 http://www.everlight.com Prepared date:12-July.-2010 Rev: 4 Page: 9 of 11 Prepared by: Yang yuanyuan 12-22/BHR6C-A01/2C Precautions For Use 1. Over-current-proof Customer must apply resistors for protection, otherwise slight voltage shift will cause big current change ( Burn out will happen ). 2. Storage 2.1 Do not open moisture proof bag before the products are ready to use. 2.2 Before opening the package: The LEDs should be kept at 30℃ or less and 90%RH or less. 2.3 After opening the package: The LED's floor life is 1 year under 30℃ or less and 60% RH or less. If unused LEDs remain, it should be stored in moisture proof packages. 2.4 If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded the storage time, baking treatment should be performed using the following conditions. Baking treatment : 60±5℃ for 24 hours. 3. Soldering Condition 3.1 Pb-free solder temperature profile 3.2 Reflow soldering should not be done more than two times. 3.3 When soldering, do not put stress on the LEDs during heating. 3.4 After soldering, do not warp the circuit board. Everlight Electronics Co., Ltd. Device No: DSE-0003879 http://www.everlight.com Prepared date:12-July.-2010 Rev: 4 Page: 10 of 11 Prepared by: Yang yuanyuan 12-22/BHR6C-A01/2C 4.Soldering Iron Each terminal is to go to the tip of soldering iron temperature less than 350℃ for 3 seconds within once in less than the soldering iron capacity 25W. Leave two seconds and more intervals, and do soldering of each terminal. Be careful because the damage of the product is often started at the time of the hand solder. 5.Repairing Repair should not be done after the LEDs have been soldered. When repairing is unavoidable, a double-head soldering iron should be used (as below figure). It should be confirmed beforehand whether the characteristics of the LEDs will or will not be damaged by repairing. EVERLIGHT ELECTRONICS CO., LTD. Office: No 25, Lane 76, Sec 3, Chung Yang Rd, Tucheng, Taipei 236, Taiwan, R.O.C Tel: 886-2-2267-2000, 2267-9936 Fax: 886-2267-6244, 2267-6189, 2267-6306 http://www.everlight.com Everlight Electronics Co., Ltd. Device No: DSE-0003879 http://www.everlight.com Prepared date:12-July.-2010 Rev: 4 Page: 11 of 11 Prepared by: Yang yuanyuan