12-23C/R6GHY2C-A01/2C

Technical Data Sheet Full Color Chip LED (Chip LED with Right Angle Lens) 12-23C/R6GHY2C-A01/2C Features ․Package in 8mm tape on 7〞diameter reel. ․Compatible with automatic placement equipment. ․Compatible with infrared and vapor phase reflow solder process. ․Multi-color type. ․Pb-free. ․The product itself will remain within RoHS compliant version. Descriptions ․The 12-23C SMD LED is much smaller than lead frame type components, thus enable smaller board size, higher packing density, reduced storage space and finally smaller equipment to be obtained. ․Besides, lightweight makes them ideal for miniature applications. etc. Applications ․Backlighting in dashboard and switch. ․Telecommunication: indicator and backlighting in telephone and fax. ․Flat backlight for LCD, switch and symbol. ․General use. Device Selection Guide Chip Emitted Color Type Material R6 AlGaInP Brilliant Red GH InGaN Brilliant Green Y2 AlGaInP Brilliant Yellow Everlight Electronics Co., Ltd. http://www.everlight.com Device No. : DSE-0001070 Prepared date20-Jan-2011 Resin Color Water Clear Rev. 2 Page: 1 of 12 Prepared by :Wangzhengyu 12-23C/R6GHY2C-A01/2C Package Outline Dimensions Note: The tolerances unless mentioned is ±0.1mm,Unit = mm Everlight Electronics Co., Ltd. http://www.everlight.com Device No. : DSE-0001070 Prepared date20-Jan-2011 Rev. 2 Page: 2 of 12 Prepared by :Wangzhengyu 12-23C/R6GHY2C-A01/2C Absolute Maximum Ratings (Ta=25℃ ℃) Parameter Symbol Rating Unit Reverse Voltage VR 5 V R6:25 Forward Current IF GH:25 mA Y2:25 R6:60 Peak Forward Current IFP (Duty 1/10 @1KHz) GH:100 mA Y2:60 R6:60 Power Dissipation Pd GH:95 mW Y2:60 R6:2000 Electrostatic Discharge (HBM) ESD GH:150 V Y2:2000 Operating Temperature Topr -40 ~ +85 ℃ Storage Temperature Tstg -40 ~ +90 ℃ Soldering Temperature Tsol Reflow Soldering : 260 ℃ for 10 sec. Hand Soldering : 350 ℃ for 3 sec. Everlight Electronics Co., Ltd. http://www.everlight.com Device No. : DSE-0001070 Prepared date20-Jan-2011 Rev. 2 Page: 3 of 12 Prepared by :Wangzhengyu 12-23C/R6GHY2C-A01/2C Electro-Optical Characteristics (Ta=25℃ ℃) Parameter Luminous Intensity Viewing Angle Symbol Iv Min. Typ. Max. R6 57 90 ---- GH 112 180 ---- Y2 45 72 ---- ----- 100 ----- deg ----- nm ----- nm ----- nm 2θ1/2 R6 Peak Wavelength Dominant Wavelength Spectrum Radiation Bandwidth λp λd GH ----- R6 624 ----- VF 525 Y2 589 R6 20 ----- Y2 Forward Voltage 518 591 △λ GH 35 IR R6 1.7 2.0 2.4 GH 2.7 3.3 3.7 Y2 1.7 2.0 2.4 GH mcd IF=20mA 15 R6 Reverse Current Condition 632 Y2 GH Unit V 10 ----- ----- Y2 50 μA VR=5V 10 Notes: 1.Tolerance of Luminous Intensity ±11% Everlight Electronics Co., Ltd. http://www.everlight.com Device No. : DSE-0001070 Prepared date20-Jan-2011 Rev. 2 Page: 4 of 12 Prepared by :Wangzhengyu 12-23C/R6GHY2C-A01/2C Typical Electro-Optical Characteristics Curves R6 Everlight Electronics Co., Ltd. http://www.everlight.com Device No. : DSE-0001070 Prepared date20-Jan-2011 Rev. 2 Page: 5 of 12 Prepared by :Wangzhengyu 12-23C/R6GHY2C-A01/2C Typical Electro-Optical Characteristics Curves GH Everlight Electronics Co., Ltd. http://www.everlight.com Device No. : DSE-0001070 Prepared date20-Jan-2011 Rev. 2 Page: 6 of 12 Prepared by :Wangzhengyu 12-23C/R6GHY2C-A01/2C Typical Electro-Optical Characteristics Curves Y2 Everlight Electronics Co., Ltd. http://www.everlight.com Device No. : DSE-0001070 Prepared date20-Jan-2011 Rev. 2 Page: 7 of 12 Prepared by :Wangzhengyu 12-23C/R6GHY2C-A01/2C Label explanation CAT: Luminous Intensity Rank Pb HUE: Dom. Wavelength Rank EVERLIGHT CPN : P N : XXXXXXXXXXXXX REF: Forward Voltage Rank RoHS XXXXXXXXXXXXX CAT : XXX HUE : XXX REF : XXX QTY : XXX LOT NO : XXXXXXXXXX Reference : XXXXXXXX MADE IN TAIWAN Reel Dimensions Note: The tolerances unless mentioned is ±0.1mm ,Unit = mm Everlight Electronics Co., Ltd. http://www.everlight.com Device No. : DSE-0001070 Prepared date20-Jan-2011 Rev. 2 Page: 8 of 12 Prepared by :Wangzhengyu 12-23C/R6GHY2C-A01/2C Carrier Tape Dimensions: Loaded quantity 2000 PCS per reel Note: The tolerances unless mentioned is ±0.1mm ,Unit = mm Moisture Resistant Packaging Label Aluminum moisture-proof bag Everlight Electronics Co., Ltd. http://www.everlight.com Device No. : DSE-0001070 Prepared date20-Jan-2011 Desiccant Label Rev. 2 Page: 9 of 12 Prepared by :Wangzhengyu 12-23C/R6GHY2C-A01/2C Reliability Test Items And Conditions The reliability of products shall be satisfied with items listed below. Confidence level：90% LTPD：10% Test Sample Hours/Cycles Size No. Items Test Condition 1 Reflow Soldering Temp. : 260℃±5℃ Min. 5sec. 6 Min. 22 PCS. 0/1 Temperature Cycle H : +100℃ 15min ∫ 5 min L : -40℃ 15min 300 Cycles 22 PCS. 0/1 Thermal Shock H : +100℃ 5min ∫ 10 sec L : -10℃ 5min 300 Cycles 22 PCS. 0/1 Temp. : 100℃ 1000 Hrs. 22 PCS. 0/1 Temp. : -40℃ 1000 Hrs. 22 PCS. 0/1 2 3 4 5 High Temperature Storage Low Temperature Storage Ac/Re 6 DC Operating Life IF = 20 mA 1000 Hrs. 22 PCS. 0/1 7 High Temperature / High Humidity 85℃/ 85%RH 1000 Hrs. 22 PCS. 0/1 Everlight Electronics Co., Ltd. http://www.everlight.com Device No. : DSE-0001070 Prepared date20-Jan-2011 Rev. 2 Page: 10 of 12 Prepared by :Wangzhengyu 12-23C/R6GHY2C-A01/2C Precautions For Use 1. Over-current-proof Customer must apply resistors for protection, otherwise slight voltage shift will cause big current change ( Burn out will happen ). 2. Storage 2.1 Do not open moisture proof bag before the products are ready to use. 2.2 Before opening the package: The LEDs should be kept at 30℃ or less and 90%RH or less. 2.3 After opening the package: The LED's floor life is 1 year under 30℃ or less and 60% RH or less. If unused LEDs remain, it should be stored in moisture proof packages. 2.4 If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded the storage time, baking treatment should be performed using the following conditions. Baking treatment : 60±5℃ for 24 hours. 3. Soldering Condition 3.1 Pb-free solder temperature profile 3.2 Reflow soldering should not be done more than two times. 3.3 When soldering, do not put stress on the LEDs during heating. 3.4 After soldering, do not warp the circuit board. Everlight Electronics Co., Ltd. http://www.everlight.com Device No. : DSE-0001070 Prepared date20-Jan-2011 Rev. 2 Page: 11 of 12 Prepared by :Wangzhengyu 12-23C/R6GHY2C-A01/2C 4.Soldering Iron Each terminal is to go to the tip of soldering iron temperature less than 350℃ for 3 seconds within once in less than the soldering iron capacity 25W. Leave two seconds and more intervals, and do soldering of each terminal. Be careful because the damage of the product is often started at the time of the hand solder. 5.Repairing Repair should not be done after the LEDs have been soldered. When repairing is unavoidable, a double-head soldering iron should be used (as below figure). It should be confirmed beforehand whether the characteristics of the LEDs will or will not be damaged by repairing. EVERLIGHT ELECTRONICS CO., LTD. Office: No 25, Lane 76, Sec 3, Chung Yang Rd, Tucheng, Taipei 236, Taiwan, R.O.C Tel: 886-2-2267-2000, 2267-9936 Fax: 886-2267-6244, 2267-6189, 2267-6306 http://www.everlight.com Everlight Electronics Co., Ltd. http://www.everlight.com Device No. : DSE-0001070 Prepared date20-Jan-2011 Rev. 2 Page: 12 of 12 Prepared by :Wangzhengyu