12-23CGH-A012C

EVERLIGHT ELECTRONICS CO.,LTD. Technical Data Sheet Full Color Chip LED (Chip LED with Right Angle Lens) 12-23C/S2GHBHC-A01/2C Features ․Package in 8mm tape on 7〞diameter reel. ․Compatible with automatic placement equipment. ․Compatible with infrared and vapor phase reflow solder process. ․Multi-color type. ․Pb-free. ․The product itself will remain within RoHS compliant version. Descriptions ․The 12-23C SMD Taping is much smaller than lead frame type components, thus enable smaller board size, higher packing density, reduced storage space and finally smaller equipment to be obtained. ․Besides, lightweight makes them ideal for miniature applications. etc. Applications ․Automotive: backlighting in dashboard and switch. ․Telecommunication: indicator and backlighting in telephone and fax. ․Flat backlight for LCD, switch and symbol. ․General use. Device Selection Guide Chip Type S2 GH BH Material AlGaInP InGaN InGaN Emitted Color Brilliant Orange Brilliant Green Blue Water Clear Lens Color Everlight Electronics Co., Ltd. Device No. : DSE-123-008 http://www.everlight.com Prepared date: 07-26-2005 Rev. 2 Page: 1 of 12 Prepared by : Jeff Tsai EVERLIGHT ELECTRONICS CO.,LTD. 12-23C/S2GHBHC-A01/2C Package Outline Dimensions 3.0 2.0 3 Blue Green 2 1.0 4 Orange 1 Anode mark R1.0 0.50 0.40 4 0.40 1 1.50 1 2 3 4 3 2 Note: The tolerances unless mentioned is ±0.1mm ,Unit = mm Everlight Electronics Co., Ltd. Device No. : DSE-123-008 http://www.everlight.com Prepared date: 07-26-2005 Rev. 2 Page: 2 of 12 Prepared by : Jeff Tsai EVERLIGHT ELECTRONICS CO.,LTD. 12-23C/S2GHBHC-A01/2C Absolute Maximum Ratings (Ta=25℃) Parameter Reverse Voltage Symbol VR Rating 5 S2:25 Forward Current IF GH:25 BH:25 Operating Temperature Storage Temperature Soldering Temperature Topr Tstg Tsol -40 ~ +85 -40 ~ +90 260 (for 5 seconds) S2:60 Power Dissipation Pd GH:110 BH:110 Peak Forward Current (Duty 1/10 @1KHz) S2:60 IFP GH:100 BH:100 mA mW ℃ ℃ ℃ mA Unit V Everlight Electronics Co., Ltd. Device No. : DSE-123-008 http://www.everlight.com Prepared date: 07-26-2005 Rev. 2 Page: 3 of 12 Prepared by : Jeff Tsai EVERLIGHT ELECTRONICS CO.,LTD. 12-23C/S2GHBHC-A01/2C Electro-Optical Characteristics (Ta=25℃) Parameter Symbol S2 Min. 72 140 36 ----- Typ. 140 210 65 100 611 Max. Unit Condition Luminous Intensity Iv GH BH ----- mcd IF=20mA Viewing Angle 2θ1/2 S2 ----- deg IF=20mA Peak Wavelength λp GH BH S2 ----- 518 468 605 ----- nm IF=20mA Dominant Wavelength λd GH BH S2 ----- 525 470 17 ----- nm IF=20mA Spectrum Radiation Bandwidth △λ GH BH S2 ----- 25 25 2.0 ----- nm IF=20mA 2.4 3.9 3.9 10 V IF=20mA Forward Voltage VF GH BH S2 ----- 3.3 3.3 Reverse Current IR GH BH ----- ----- 50 50 μA VR=5V Notes: 1.Tolerance of Luminous Intensity ±10% 2.Tolerance of Dominant Wavelength ±1nm 3.Tolerance of Forward Voltage ±0.1V Everlight Electronics Co., Ltd. Device No. : DSE-123-008 http://www.everlight.com Prepared date: 07-26-2005 Rev. 2 Page: 4 of 12 Prepared by : Jeff Tsai EVERLIGHT ELECTRONICS CO.,LTD. 12-23C/S2GHBHC-A01/2C Typical Electro-Optical Characteristics Curves S2 Everlight Electronics Co., Ltd. Device No. : DSE-123-008 http://www.everlight.com Prepared date: 07-26-2005 Rev. 2 Page: 5 of 12 Prepared by : Jeff Tsai EVERLIGHT ELECTRONICS CO.,LTD. 12-23C/S2GHBHC-A01/2C Typical Electro-Optical Characteristics Curves GH Everlight Electronics Co., Ltd. Device No. : DSE-123-008 http://www.everlight.com Prepared date: 07-26-2005 Rev. 2 Page: 6 of 12 Prepared by : Jeff Tsai EVERLIGHT ELECTRONICS CO.,LTD. 12-23C/S2GHBHC-A01/2C Typical Electro-Optical Characteristics Curves BH Everlight Electronics Co., Ltd. Device No. : DSE-123-008 http://www.everlight.com Prepared date: 07-26-2005 Rev. 2 Page: 7 of 12 Prepared by : Jeff Tsai EVERLIGHT ELECTRONICS CO.,LTD. 12-23C/S2GHBHC-A01/2C Label explanation CAT: Luminous Intensity Rank HUE: Dom. Wavelength Rank REF: Forward Voltage Rank xxxxxx xxxxxx RoHS xxxxxxxxxxxx xxxx xxxxxxxx Reel Dimensions Note: The tolerances unless mentioned is ±0.1mm ,Unit = mm Everlight Electronics Co., Ltd. Device No. : DSE-123-008 http://www.everlight.com Prepared date: 07-26-2005 Rev. 2 Page: 8 of 12 Prepared by : Jeff Tsai EVERLIGHT ELECTRONICS CO.,LTD. 12-23C/S2GHBHC-A01/2C Carrier Tape Dimensions: Loaded quantity 2000 PCS per reel Note: The tolerances unless mentioned is ±0.1mm ,Unit = mm Moisture Resistant Packaging Label Aluminum moistue-proof bag Desiccant Label Everlight Electronics Co., Ltd. Device No. : DSE-123-008 http://www.everlight.com Prepared date: 07-26-2005 Rev. 2 Page: 9 of 12 Prepared by : Jeff Tsai EVERLIGHT ELECTRONICS CO.,LTD. 12-23C/S2GHBHC-A01/2C Reliability Test Items And Conditions The reliability of products shall be satisfied with items listed below. Confidence level：90% LTPD：10% No. 1 Items Reflow Soldering Test Condition Temp. : 260℃±5℃ Min. 5sec. H : +100℃ 15min ∫ 5 min L : -40℃ 15min H : +100℃ 5min ∫ 10 sec L : -10℃ 5min Temp. : 100℃ Temp. : -40℃ IF = 20 mA 85℃/ 85%RH Test Sample Hours/Cycles Size 6 Min. 300 Cycles 22 PCS. Ac/Re 0/1 2 Temperature Cycle 22 PCS. 0/1 3 Thermal Shock High Temperature Storage Low Temperature Storage DC Operating Life High Temperature / High Humidity 300 Cycles 1000 Hrs. 1000 Hrs. 1000 Hrs. 1000 Hrs. 22 PCS. 0/1 4 5 6 7 22 PCS. 22 PCS. 22 PCS. 22 PCS. 0/1 0/1 0/1 0/1 Everlight Electronics Co., Ltd. Device No. : DSE-123-008 http://www.everlight.com Prepared date: 07-26-2005 Rev. 2 Page: 10 of 12 Prepared by : Jeff Tsai EVERLIGHT ELECTRONICS CO.,LTD. 12-23C/S2GHBHC-A01/2C Precautions For Use 1. Over-current-proof Customer must apply resistors for protection , otherwise slight voltage shift will cause big current change ( Burn out will happen ). 2. Storage 2.1 Do not open moisture proof bag before the products are ready to use. 2.2 Before opening the package, the LEDs should be kept at 30℃ or less and 90%RH or less. 2.3 The LEDs should be used within a year. 2.4 After opening the package, the LEDs should be kept at 30℃ or less and 70%RH or less. 2.5 The LEDs should be used within 168 hours (7 days) after opening the package. 2.6 If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded the storage time, baking treatment should be performed using the following conditions. Baking treatment : 60±5℃ for 24 hours. 3. Soldering Condition 3.1 Pb-free solder temperature profile 3.2 Reflow soldering should not be done more than two times. 3.3 When soldering, do not put stress on the LEDs during heating. 3.4 After soldering, do not warp the circuit board. 4. Soldering Iron Each terminal is to go to the tip of soldering iron temperature less than 280℃ for 3 seconds within once in less than the soldering iron capacity 25W. Leave two seconds and more intervals, and do soldering of each terminal. Be careful because the damage of the product is often started at the time of the hand solder. Everlight Electronics Co., Ltd. Device No. : DSE-123-008 http://www.everlight.com Prepared date: 07-26-2005 Rev. 2 Page: 11 of 12 Prepared by : Jeff Tsai EVERLIGHT ELECTRONICS CO.,LTD. 12-23C/S2GHBHC-A01/2C 5.Repairing Repair should not be done after the LEDs have been soldered. When repairing is unavoidable, a double-head soldering iron should be used (as below figure). It should be confirmed beforehand whether the characteristics of the LEDs will or will not be damaged by repairing. EVERLIGHT ELECTRONICS CO., LTD. Office: No 25, Lane 76, Sec 3, Chung Yang Rd, Tucheng, Taipei 236, Taiwan, R.O.C Tel: 886-2-2267-2000, 2267-9936 Fax: 886-2267-6244, 2267-6189, 2267-6306 http://www.everlight.com Everlight Electronics Co., Ltd. Device No. : DSE-123-008 http://www.everlight.com Prepared date: 07-26-2005 Rev. 2 Page: 12 of 12 Prepared by : Jeff Tsai