16-213SYGC/S530-E3/TR8

Technical Data Sheet 0402 Package Chip LED (0.45 mm Height) 16-213SYGC/S530-XX/TR8 Features ․Package in 8mm tape on 7〞diameter reel. ․Compatible with automatic placement equipment. ․Compatible with infrared and vapor phase reflow solder process. ․Mono-color type. ․Pb-free. ․The product itself will remain within RoHS compliant version. Descriptions ․The 16-213 SMD LED is much smaller than lead frame type components, thus enable smaller board size, higher packing density, reduced storage space and finally smaller equipment to be obtained. ․ Besides, lightweight makes them ideal for miniature applications. etc. Applications ․Backlighting in dashboard and switch. ․Telecommunication: indicator and backlighting in telephone and fax. ․Flat backlight for LCD, switch and symbol. ․General use. Device Selection Guide Chip Material Emitted Color AlGaInP Brilliant Yellow Green Resin Color Water Clear Everlight Electronics Co., Ltd. http://www.everlight.com Rev 2 Device No: DSE-163-023 Prepared date: 08-Jan-2009 Prepared by: Betty Lin Page: 1 of 10 16-213SYGC/S530-XX/TR8 Package Outline Dimensions Note: The tolerances unless mentioned is ±0.1mm ,Unit = mm Everlight Electronics Co., Ltd. http://www.everlight.com Rev 2 Device No: DSE-163-023 Prepared date: 08-Jan-2009 Prepared by: Betty Lin Page: 2 of 10 16-213SYGC/S530-XX/TR8 Absolute Maximum Ratings (Ta=25℃) Parameter Symbol Rating Unit Reverse Voltage VR 5 V Forward Current IF 25 mA Peak Forward Current (Duty 1/10 @1KHz) IFP 60 mA Power Dissipation Pd 60 mW Electrostatic Discharge(HBM) ESD 2000 V Operating Temperature Topr -40 ~ +85 ℃ Storage Temperature Tstg -40 ~ +90 ℃ Soldering Temperature Tsol Reflow Soldering : 260 ℃ for 10 sec. Hand Soldering : 350 ℃ for 3 sec. Everlight Electronics Co., Ltd. http://www.everlight.com Rev 2 Device No: DSE-163-023 Prepared date: 08-Jan-2009 Prepared by: Betty Lin Page: 3 of 10 16-213SYGC/S530-XX/TR8 Electro-Optical Characteristics (Ta=25℃) Parameter Luminous Intensity Symbol Iv *Chip Min. Typ. Max. E1 10 15 ----- E2 20 25 ----- E3 30 35 ----- E4 40 45 ----- Rank Unit mcd Viewing Angle 2θ1/2 ----- ----- 120 ----- deg Peak Wavelength λp ----- ----- 575 ----- nm λd ----- ----- 573 ----- nm Spectrum Radiation Bandwidth △λ ----- ----- 20 ----- nm Forward Voltage VF ----- 1.7 2.0 2.4 V Reverse Current IR ----- ----- ----- 10 μA Dominant Wavelength Condition IF=20mA VR=5V *16-213SYGC/S530-XX/TR8 Chip Rank Everlight Electronics Co., Ltd. http://www.everlight.com Rev 2 Device No: DSE-163-023 Prepared date: 08-Jan-2009 Prepared by: Betty Lin Page: 4 of 10 16-213SYGC/S530-XX/TR8 Typical Electro-Optical Characteristics Curves Forward Current vs. Forward Voltage Spectrum Distribution Ta=25°C Forward Current Relative luminous intensity (%) IF(mA) Ta=25°C Forward Voltage VF (V) Wavelength λ (nm) Luminous Intensity vs. Forward Current Ta=25°C Luminous Intensity vs. Relative luminous intensity (% ) Relative luminous intensity (% ) Ambient Temperature Ambient Temperature Ta (°C) Radiation Diagram IF(mA) Ta=25°C Forward Current IF(mA) Forward Current Derating Curve Forward Current Ambient Temperature Ta (°C) Everlight Electronics Co., Ltd. http://www.everlight.com Rev 2 Device No: DSE-163-023 Prepared date: 08-Jan-2009 Prepared by: Betty Lin Page: 5 of 10 16-213SYGC/S530-XX/TR8 Label Explanation CAT: Luminous Intensity Rank HUE: Dom. Wavelength Rank Pb REF: Forward Voltage Rank CPN : P N : XXXXXXXXXXXXX EVERLIGHT RoHS XXXXXXXXXXXXX CAT : XXX HUE : XXX REF : XXX QTY : XXX LOT NO : XXXXXXXXXX MSL-2 Reference : XXXXXXXX MADE IN TAIWAN Reel Dimensions Note: The tolerances unless mentioned is ±0.1mm ,Unit = mm Everlight Electronics Co., Ltd. http://www.everlight.com Rev 2 Device No: DSE-163-023 Prepared date: 08-Jan-2009 Prepared by: Betty Lin Page: 6 of 10 16-213SYGC/S530-XX/TR8 Carrier Tape Dimensions: Loaded quantity 3000 PCS per reel Note: The tolerances unless mentioned is ±0.1mm ,Unit = mm Moisture Resistant Packaging Label Aluminum moisture-proof bag Desiccant Label Everlight Electronics Co., Ltd. http://www.everlight.com Rev 2 Device No: DSE-163-023 Prepared date: 08-Jan-2009 Prepared by: Betty Lin Page: 7 of 10 16-213SYGC/S530-XX/TR8 Reliability Test Items And Conditions The reliability of products shall be satisfied with items listed below. Confidence level：90% LTPD：10% No. Items 1 Reflow Soldering 2 Temperature Cycle 3 Thermal Shock 4 5 6 High Temperature Storage Low Temperature Storage DC Operating Life High Temperature / High Humidity Test Condition Temp. : 260℃±5℃ Min. 5sec. H : +100℃ 15min ∫ 5 min L : -40℃ 15min H : +100℃ 5min ∫ 10 sec L : -10℃ 5min Temp. : 100℃ Temp. : -40℃ Test Sample Hours/Cycles Size Ac/Re 6 Min. 22 PCS. 0/1 300 Cycles 22 PCS. 0/1 300 Cycles 22 PCS. 0/1 22 PCS. 0/1 22 PCS. 0/1 1000 Hrs. 1000 Hrs. IF = 20 mA 1000 Hrs. 22 PCS. 0/1 85℃/ 85%RH 1000 Hrs. 22 PCS. 0/1 Everlight Electronics Co., Ltd. http://www.everlight.com Rev 2 Device No: DSE-163-023 Prepared date: 08-Jan-2009 Prepared by: Betty Lin 7 Page: 8 of 10 16-213SYGC/S530-XX/TR8 Precautions For Use 1. Over-current-proof Customer must apply resistors for protection, otherwise slight voltage shift will cause big current change ( Burn out will happen ). 2. Storage 2.1 Do not open moisture proof bag before the products are ready to use. 2.2 Before opening the package: The LEDs should be kept at 30℃ or less and 90%RH or less. 2.3 After opening the package: The LED's floor life is 1 year under 30℃ or less and 60% RH or less. If unused LEDs remain, it should be stored in moisture proof packages. 2.4 If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded the storage time, baking treatment should be performed using the following conditions. Baking treatment : 60±5℃ for 24 hours. 3. Soldering Condition 3.1 Pb-free solder temperature profile 1~5 °C / Sec. 260°C. Max. 10 Sec. Max. 1~5 °C / Sec. Pre-heating 180~200°C 60 Sec. Max. Above 220°C 120 Sec. Max. 3.2 Reflow soldering should not be done more than two times. 3.3 When soldering, do not put stress on the LEDs during heating. 3.4 After soldering, do not warp the circuit board. Everlight Electronics Co., Ltd. http://www.everlight.com Rev 2 Device No: DSE-163-023 Prepared date: 08-Jan-2009 Prepared by: Betty Lin Page: 9 of 10 16-213SYGC/S530-XX/TR8 4.Soldering Iron Each terminal is to go to the tip of soldering iron temperature less than 350℃ for 3 seconds within once in less than the soldering iron capacity 25W. Leave two seconds and more intervals, and do soldering of each terminal. Be careful because the damage of the product is often started at the time of the hand solder. 5.Repairing Repair should not be done after the LEDs have been soldered. When repairing is unavoidable, a double-head soldering iron should be used (as below figure). It should be confirmed beforehand whether the characteristics of the LEDs will or will not be damaged by repairing. Everlight Electronics Co., Ltd. http://www.everlight.com Rev 2 Device No: DSE-163-023 Prepared date: 08-Jan-2009 Prepared by: Betty Lin Page: 10 of 10