EVERLIGHT ELECTRONICS CO., LTD.
Technical Data Sheet 0805 Package Chip LED (1.1mm Height)
17-21/R7C-AN2Q1B/3T
Features
․Package in 8mm tape on 7〞diameter reel. ․Compatible with automatic placement equipment. ․Compatible with infrared and vapor phase reflow solder process. ․Mono-color type. ․Pb-free
Descriptions
․The 17-21 SMD Taping is much smaller than lead frame type components, thus enable smaller board size, higher packing density, reduced storage space and finally smaller equipment to be obtained. ․Besides, lightweight makes them ideal for miniature applications, etc.
Applications
․Automotive: backlighting in dashboard and switch. ․Telecommunication: indicator and backlighting in telephone and fax. ․Flat backlight for LCD, switch and symbol. ․General use.
Device Selection Guide
Chip Material AlGaInP Emitted Color Dark Red
PART No. 17-21/R7C-AN1P2B/3T
Lens Color Water Clear
Everlight Electronics Co., Ltd. Device No: SZDSE-171-R03
http://www.everlight.com Prepared date: 25-Jan-2005
Rev.: 1
Page: 1 of 10
Prepared by: Huadong DEN
EVERLIGHT ELECTRONICS CO., LTD.
17-21/R7C-AN2Q1B/3T
Package Outline Dimensions
-
+
Note: The tolerances unless mentioned are ±0.1, unit = mm.
Everlight Electronics Co., Ltd. Device No: SZDSE-171-R03
http://www.everlight.com Prepared date: 25-Jan-2005
Rev.: 1
Page: 2 of 10
Prepared by: Huadong DEN
EVERLIGHT ELECTRONICS CO., LTD.
17-21/R7C-AN2Q1B/3T
Absolute Maximum Ratings (Ta=25℃)
Parameter Reverse Voltage Forward Current Operating Temperature Storage Temperature Soldering Temperature Electrostatic Discharge Power Dissipation Peak Forward Current (Duty 1/10 @1KHz) Symbol VR IF Topr Tstg Tsol ESD Pd IFP Rating 5 25 -40 ~ +85 -40~ +90 260 (for 5 seconds) 2000 60 60 Unit V mA ℃ ℃ ℃ V mW mA
Electro-Optical Characteristics (Ta=25℃)
Parameter
Luminous Intensity Viewing Angle Peak Wavelength
Dominant Wavelength
Symbol Iv 2θ1/2 λp λd △λ VF IR
Min. 36.0 --------629.5 ----1.75 -----
Typ. ----140 639 ---20 ---------
Max. 90.0 --------645.5 ----2.35 10
Unit mcd deg nm nm nm V μA
Condition
IF=20 mA
Spectrum Radiation Bandwidth Forward Voltage
Reverse Current
VR=5V
Notes:
1.Tolerance of Luminous Intensity ±10% 2.Tolerance of Dominant Wavelength ±1nm 3.Tolerance of Forward Voltage ±0.1V
Everlight Electronics Co., Ltd. Device No: SZDSE-171-R03
http://www.everlight.com Prepared date: 25-Jan-2005
Rev.: 1
Page: 3 of 10
Prepared by: Huadong DEN
EVERLIGHT ELECTRONICS CO., LTD.
17-21/R7C-AN2Q1B/3T
Bin Range Of Dom. Wavelength
Group Bin E7 A E8 E9 E10 Min 629.5 633.5 637.5 641.5 Max 633.5 637.5 641.5 645.5 nm IF=20mA Unit Condition
Bin Range Of Luminous Intensity
Bin N2 P1 P2 Q1 Min 36.0 45.0 57.0 72.0 Max 45.0 57.0 72.0 90.0 mcd IF=20mA Unit Condition
Bin Range Of Forward Voltage
Groups B Bin 0 1 2 Min 1.75 1.95 2.15 Max 1.95 2.15 2.35 V IF=20mA Unit Condition
Notes:
1.Tolerance of Luminous Intensity ±10% 2.Tolerance of Dominant Wavelength ±1nm 3.Tolerance of Forward Voltage ±0.1V
Everlight Electronics Co., Ltd. Device No: SZDSE-171-R03
http://www.everlight.com Prepared date: 25-Jan-2005
Rev.: 1
Page: 4 of 10
Prepared by: Huadong DEN
EVERLIGHT ELECTRONICS CO., LTD.
17-21/R7C-AN2Q1B/3T
Typical Electro-Optical Characteristics Curves
Everlight Electronics Co., Ltd. Device No: SZDSE-171-R03
http://www.everlight.com Prepared date: 25-Jan-2005
Rev.: 1
Page: 5 of 10
Prepared by: Huadong DEN
EVERLIGHT ELECTRONICS CO., LTD.
17-21/R7C-AN2Q1B/3T
Label explanation
CAT: Luminous Intensity Rank HUE: Dom. Wavelength Rank REF: Forward Voltage Rank
Reel Dimensions
Note: The tolerances unless mentioned are ±0.1, unit = mm.
Everlight Electronics Co., Ltd. Device No: SZDSE-171-R03
http://www.everlight.com Prepared date: 25-Jan-2005
Rev.: 1
Page: 6 of 10
Prepared by: Huadong DEN
EVERLIGHT ELECTRONICS CO., LTD.
17-21/R7C-AN2Q1B/3T
Carrier Tape Dimensions: Loaded quantity 3000 PCS per reel
Note: The tolerances unless mentioned are ±0.1, unit = mm.
Moisture Resistant Packaging
Label
Aluminum moisture-proof bag
Desiccant
Label
Everlight Electronics Co., Ltd. Device No: SZDSE-171-R03
http://www.everlight.com Prepared date: 25-Jan-2005
Rev.: 1
Page: 7 of 10
Prepared by: Huadong DEN
EVERLIGHT ELECTRONICS CO., LTD.
17-21/R7C-AN2Q1B/3T
Reliability Test Items And Conditions The reliability of products shall be satisfied with items listed below. Confidence level : 90 % LTPD : 10 % Test Sample No. Items Test Condition Hours/Cycles Size Temp. : 260℃±5℃ 6 min. 1 Reflow Soldering 22 Pcs. Min.5 sec. H : +100℃ 15min. 300 Cycles 2 Temperature Cycle 22 Pcs. ∫ 5 min. L : -40℃ 15min. 3 Thermal Shock High Temperature Storage Low Temperature Storage DC Operating Life High Temperature / High Humidity H : +100℃ 5min. ∫ 10 sec. L : -10℃ 5min. Temp. : 100℃ Temp. : -40℃ IF = 20 mA 85℃/ 85% R.H. 300 Cycles 1000 Hrs. 1000 Hrs. 1000 Hrs. 1000 Hrs. 22 Pcs.
Ac/Re 0/1
0/1
0/1
4 5 6 7
22 Pcs. 22 Pcs. 22 Pcs. 22 Pcs.
0/1 0/1 0/1 0/1
Everlight Electronics Co., Ltd. Device No: SZDSE-171-R03
http://www.everlight.com Prepared date: 25-Jan-2005
Rev.: 1
Page: 8 of 10
Prepared by: Huadong DEN
EVERLIGHT ELECTRONICS CO., LTD.
17-21/R7C-AN2Q1B/3T
Precautions For Use
1. Over-current-proof Customer must apply resistors for protection , otherwise slight voltage shift will cause big current change ( Burn out will happen ). 2. Storage 2.1 Do not open moisture proof bag before the products are ready to use. 2.2 Before opening the package, the LEDs should be kept at 30℃ or less and 90%RH or less. 2.3 The LEDs should be used within a year. 2.4 After opening the package, the LEDs should be kept at 30℃ or less and 70%RH or less. 2.5 The LEDs should be used within 168 hours (7 days) after opening the package. 2.6 If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded the storage time, baking treatment should be performed using the following conditions. Baking treatment : 60±5℃ for 24 hours. 3. Soldering Condition 3.1 Pb-free solder temperature profile
3.2 Reflow soldering should not be done more than two times. 3.3 When soldering, do not put stress on the LEDs during heating. 3.4 After soldering, do not warp the circuit board. 4. Soldering Iron Each terminal is to go to the tip of soldering iron temperature less than 280℃ for 3 seconds within once in less than the soldering iron capacity 25W. Leave two seconds and more intervals, and do soldering of each terminal. Be careful because the damage of the product is often started at the time of the hand solder.
Everlight Electronics Co., Ltd. Device No: SZDSE-171-R03 http://www.everlight.com Prepared date: 25-Jan-2005 Rev.: 1 Page: 9 of 10
Prepared by: Huadong DEN
EVERLIGHT ELECTRONICS CO., LTD.
17-21/R7C-AN2Q1B/3T
5.Repairing Repair should not be done after the LEDs have been soldered. When repairing is unavoidable, a double-head soldering iron should be used (as below figure). It should be confirmed beforehand whether the characteristics of the LEDs will or will not be damaged by repairing.
EVERLIGHT ELECTRONICS CO., LTD. Office: No 25, Lane 76, Sec 3, Chung Yang Rd, Tucheng, Taipei 236, Taiwan, R.O.C
Tel: 886-2-2267-2000, 2267-9936 Fax: 886-2267-6244, 2267-6189, 2267-6306 http://www.everlight.com
Everlight Electronics Co., Ltd. Device No: SZDSE-171-R03
http://www.everlight.com Prepared date: 25-Jan-2005
Rev.: 1
Page: 10 of 10
Prepared by: Huadong DEN
