17-21SURC/S530-A2/TR8

SMD  B 17-21SURC/S530-A2 /TR8 Features ․Package in 8mm tape on 7〞diameter reel. ․Compatible with automatic placement equipment. ․Compatible with infrared and vapor phase reflow solder process. ․Mono-color type. ․Pb-free. ․The product itself will remain within RoHS compliant version. Description ․The 17-21 SMD LED is much smaller than lead frame type components, thus enable smaller board size, 1 Copyright Revision :4 © LifecyclePhase: Release Date:2015-01-07 11:20:08.0 2010, Everlight All Rights Reserved. Release Date : Jan 6.2015. Issue No:DSE-0008896 Rev.4 www.everlight.com Expired Period: Forever DATASHEET SMD  REFLECTOR 17-21SURC/S530-A2 /TR8 higher packing density, reduced storage space and finally smaller equipment to be obtained. ․Besides, lightweight makes them ideal for miniature applications. etc. Applications ․Telecommunication: indicator and backlighting in telephone and fax. ․Flat backlight for LCD, switch and symbol. ․General use. Device Selection Guide Chip Emitted Color Resin Color Brilliant Red Water Clear Materials AlGaInP Absolute Maximum Ratings (Ta=25℃) Parameter Symbol Rating Unit Reverse Voltage VR 5 V Forward Current IF 25 mA IFP 60 mA Power Dissipation Pd 60 mW Operating Temperature Topr -40 ~ +85 ℃ Storage Temperature Tstg -40 ~ +90 ℃ Electrostatic Discharge ESDHBM 2000 V Soldering Temperature Tsol Reflow Soldering : 260 ℃ for 10 sec. Peak Forward Current (Duty 1/10 @1KHz) 2 Copyright Revision :4 © LifecyclePhase: Release Date:2015-01-07 11:20:08.0 2010, Everlight All Rights Reserved. Release Date : : Jan 6.2015. Issue No:DSE-0008896 Rev.4 www.everlight.com Expired Period: Forever DATASHEET SMD  REFLECTOR 17-21SURC/S530-A2 /TR8 Hand Soldering : 350 ℃ for 3 sec. Electro-Optical Characteristics (Ta=25℃) Parameter Symbol Min. Typ. Max. Unit Luminous Intensity Iv 15 38 ----- mcd Viewing Angle 2θ1/2 ----- 140 ----- deg Peak Wavelength λp ----- 632.0 ----- nm Dominant Wavelength λd ----- 624.0 ----- nm Spectrum Radiation Bandwidth △λ ----- 20 ------ nm Forward Voltage VF 1.7 2.0 2.4 V Reverse Current IR ----- ----- 10 μA Condition IF=20mA VR=5V Typical Electro-Optical Characteristics Curves 3 Copyright Revision :4 © LifecyclePhase: Release Date:2015-01-07 11:20:08.0 2010, Everlight All Rights Reserved. Release Date : : Jan 6.2015. Issue No:DSE-0008896 Rev.4 www.everlight.com Expired Period: Forever DATASHEET SMD  REFLECTOR 17-21SURC/S530-A2 /TR8 Forward Current vs. Forward Voltage Ta=25°C 50 I (mA) 100 75 Forward Current Relative luminous intensity (%) Spectrum Distribution 50 25 0 500 550 600 650 Wavelength λ (nm) 40 30 25 20 10 0 1.2 700 Ambient Temperature Relative luminous intensity (%) Relative luminous intensity (%) Luminous Intensity vs. 1000 100 10 1 -60 -40 -20 0 20 40 60 80 100 1000 1.6 2.0 2.8 3.0 Luminous Intensity vs Forward Current Ta=25°C f=1KHz Duty=1/10 10 1 10 10 10 Forward Current IF(mA) Radiation Diagram Forward Current Derating Curve 0° 50 IF(mA) 2.4 100 Ambient Temperature Ta (°C) Forward Current Ta=25°C Ta=25°C 10° 20° 30° 40 40° 1.0 30 25 0.9 50° 20 0.8 60° 10 0.7 70° 80° 90° 0 0 20 40 60 85 100 0.5 0.3 0.1 0.2 0.4 0.6 Ambient Temperature Ta (°C) 4 Copyright Revision :4 © LifecyclePhase: Release Date:2015-01-07 11:20:08.0 2010, Everlight All Rights Reserved. Release Date : : Jan 6.2015. Issue No:DSE-0008896 Rev.4 www.everlight.com Expired Period: Forever DATASHEET SMD  REFLECTOR 17-21SURC/S530-A2 /TR8 Package Outline Dimensions Cathode mark Note: Tolerances unless mentioned ±0.1mm. Unit = mm 5 Copyright Revision :4 © LifecyclePhase: Release Date:2015-01-07 11:20:08.0 2010, Everlight All Rights Reserved. Release Date : : Jan 6.2015. Issue No:DSE-0008896 Rev.4 www.everlight.com Expired Period: Forever DATASHEET SMD  REFLECTOR 17-21SURC/S530-A2 /TR8 Moisture Resistant Packing Materials Label Explanation ‧CAT: Luminous Intensity Rank ‧HUE: Chromaticity Coordinates Rank ‧REF: Forward Voltage Rank Reel Dimensions 6 Copyright Revision :4 © LifecyclePhase: Release Date:2015-01-07 11:20:08.0 2010, Everlight All Rights Reserved. Release Date : : Jan 6.2015. Issue No:DSE-0008896 Rev.4 www.everlight.com Expired Period: Forever DATASHEET SMD  REFLECTOR 17-21SURC/S530-A2 /TR8 Note: The tolerances unless mentioned is ±0.1mm ,Unit = mm Carrier Tape Dimensions: Loaded quantity 3000 PCS per reel Note: The tolerances unless mentioned is ±0.1mm ,Unit = mm Moisture Resistant Packaging 7 Copyright Revision :4 © LifecyclePhase: Release Date:2015-01-07 11:20:08.0 2010, Everlight All Rights Reserved. Release Date : : Jan 6.2015. Issue No:DSE-0008896 Rev.4 www.everlight.com Expired Period: Forever DATASHEET SMD  REFLECTOR 17-21SURC/S530-A2 /TR8 Aluminum moisture-proof bag Label Desiccant Label Precautions For Use 1. Over-current-proof Customer must apply resistors for protection, otherwise slight voltage shift will cause big current change ( Burn out will happen ). 2. Storage 2.1 Do not open moisture proof bag before the products are ready to use. 2.2 Before opening the package: The LEDs should be kept at 30℃ or less and 90%RH or less. 2.3 After opening the package: The LED's floor life is 1 year under 30℃ or less and 60% RH or less. If unused LEDs remain, it should be stored in moisture proof packages. 2.4 If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded the storage time, baking treatment should be performed using the following conditions. Baking treatment : 60±5℃ for 24 hours. 3. Soldering Condition 3.1 Pb-free solder temperature profile 8 Copyright Revision :4 © LifecyclePhase: Release Date:2015-01-07 11:20:08.0 2010, Everlight All Rights Reserved. Release Date : : Jan 6.2015. Issue No:DSE-0008896 Rev.4 www.everlight.com Expired Period: Forever DATASHEET SMD  REFLECTOR 17-21SURC/S530-A2 /TR8 260°C Max. 10sec. Max. Above255°C 30sec.Max. 3°C/sec.Max. 6°C/sec.Max. Pre-heating Above 217°C 60~150sec. 150~200°C 60~120sec. 3.2 Reflow soldering should not be done more than two times. 3.3 When soldering, do not put stress on the LEDs during heating. 3.4 After soldering, do not warp the circuit board. 4.Soldering Iron Each terminal is to go to the tip of soldering iron temperature less than 350℃ for 3 seconds within once in less than the soldering iron capacity 25W. Leave two seconds and more intervals, and do soldering of each terminal. Be careful because the damage of the product is often started at the time of the hand solder. 5.Repairing Repair should not be done after the LEDs have been soldered. When repairing is unavoidable, a double-head soldering iron should be used (as below figure). It should be confirmed beforehand whether the characteristics of the LEDs will or will not be damaged by repairing. 9 Copyright Revision :4 © LifecyclePhase: Release Date:2015-01-07 11:20:08.0 2010, Everlight All Rights Reserved. Release Date : : Jan 6.2015. Issue No:DSE-0008896 Rev.4 www.everlight.com Expired Period: Forever DATASHEET SMD  REFLECTOR 17-21SURC/S530-A2 /TR8 Application Restrictions High reliability applications such as military/aerospace, automotive safety/security systems, 10 Copyright Revision :4 © LifecyclePhase: Release Date:2015-01-07 11:20:08.0 2010, Everlight All Rights Reserved. Release Date : : Jan 6.2015. Issue No:DSE-0008896 Rev.4 www.everlight.com Expired Period: Forever DATASHEET SMD  REFLECTOR 17-21SURC/S530-A2 /TR8 and medical equipment may require different product. If you have any concerns, please contact Everlight before using this product in your application. This specification guarantees the quality and performance of the product as an individual component. Do not use this product beyond the specification described in this document. 11 Copyright Revision :4 © LifecyclePhase: Release Date:2015-01-07 11:20:08.0 2010, Everlight All Rights Reserved. Release Date : : Jan 6.2015. Issue No:DSE-0008896 Rev.4 www.everlight.com Expired Period: Forever