19-217/G7C-AL1M2B/3T

EVERLIGHT ELECTRONICS CO.,LTD. Technical Data Sheet 0603 Package Chip LED(0.4mm Height) 19-217/G7C-AL1M2B/3T Features ․Package in 8mm tape on 7〞diameter reel. ․Compatible with automatic placement equipment. ․Compatible with infrared and vapor phase reflow solder process. ․Mono-color type. ․Pb-free. ․The product itself will remain within RoHS complaint version Descriptions ․The 19-217 SMD Taping is much smaller than lead frame type components, thus enable smaller board size, higher packing density, reduced storage space and finally smaller equipment to be obtained. ․Besides, lightweight makes them ideal for miniature applications. etc. Applications ․Backlighting in dashboard and switch. ․Telecommunication: indicator and backlighting in telephone and fax. ․Flat backlight for LCD, switch and symbol. ․General use. Device Selection Guide Part No. 19-217/G7C-AL1M2B/3T Everlight Electronics Co., Ltd. Device No:SZDSE-197-G01 Chip Lens Color Material Emitted Color AlGaInP Brilliant Yellow Green http://www.everlight.com Prepared date: 17-10-2006 Rev. 2 Water Clear Page: 1 of 10 Prepared by: Bian ChangYou EVERLIGHT ELECTRONICS CO.,LTD. 19-217/G7C-AL1M2B/3T Package Outline Dimensions Note: The tolerances unless mentioned is ±0.1mm ,Unit Everlight Electronics Co., Ltd. Device No:SZDSE-197-G01 http://www.everlight.com Prepared date: 17-10-2006 Rev. 2 Page: 2 of 10 Prepared by: Bian ChangYou EVERLIGHT ELECTRONICS CO.,LTD. 19-217/G7C-AL1M2B/3T Absolute Maximum Ratings (Ta=25℃) Parameter Symbol Rating Unit Reverse Voltage VR 5 V Forward Current IF 25 mA IFP 60 mA Power Dissipation Pd 60 mW Electrostatic Discharge(HBM) ESD 2000 V Operating Temperature Topr -40 ~ +85 ℃ Storage Temperature Tstg -40 ~ +90 ℃ Soldering Temperature Tsol Peak Forward Current (Duty 1/10 @1KHz) Reflow Soldering : 260 ℃ for 10 sec. Hand Soldering : 350 ℃ for 3 sec. Electro-Optical Characteristics (Ta=25℃) Parameter Symbol Min. Typ. Max. Unit Luminous Intensity Iv 11.5 ----- 28.5 mcd Viewing Angle 2θ1/2 ----- 120 ----- deg Peak Wavelength Dominant Wavelength λp ----- 575 ----- nm λd 569.5 ----- 577.5 nm Spectrum Radiation Bandwidth △λ ----- 20 ----- nm Forward Voltage VF 1.75 ----- 2.35 V Reverse Current IR ----- ----- 10 μA Condition IF=20mA VR=5V Notes: 1.Tolerance of Luminous Intensity ±10% 2.Tolerance of Dominant Wavelength ±1nm 3.Tolerance of Forward Voltage ±0.1V Everlight Electronics Co., Ltd. Device No:SZDSE-197-G01 http://www.everlight.com Prepared date: 17-10-2006 Rev. 2 Page: 3 of 10 Prepared by: Bian ChangYou EVERLIGHT ELECTRONICS CO.,LTD. 19-217/G7C-AL1M2B/3T Bin Range Of Dom. Wavelength Group A Bin Min Max C16 569.5 571.5 C17 571.5 573.5 C18 573.5 575.5 C19 575.5 577.5 Unit Condition nm IF=20mA Bin Range Of Luminous Intensity Bin Min Max L1 11.5 14.5 L2 14.5 18.0 M1 18.0 22.5 M2 22.5 28.5 Unit Condition mcd IF=20mA Bin Range Of Forward Voltage Group B Bin Min Max 0 1.75 1.95 1 1.95 2.15 2 2.15 2.35 Unit Condition V IF=20mA Notes: 1.ToleLance of Luminous Intensity ±10% 2.ToleLance of Dominant Wavelength ±1nm 3.ToleLance of FoLwaLd Voltage ±0.1V Everlight Electronics Co., Ltd. Device No:SZDSE-197-G01 http://www.everlight.com Prepared date: 17-10-2006 Rev. 2 Page: 4 of 10 Prepared by: Bian ChangYou EVERLIGHT ELECTRONICS CO.,LTD. 19-217/G7C-AL1M2B/3T Typical ElectLo-Optical ChaLacteListics CuLves Everlight Electronics Co., Ltd. Device No:SZDSE-197-G01 http://www.everlight.com Prepared date: 17-10-2006 Rev. 2 Page: 5 of 10 Prepared by: Bian ChangYou EVERLIGHT ELECTRONICS CO.,LTD. 19-217/G7C-AL1M2B/3T Label explanation CAT: Luminous Intensity Lank HUE: Dom. Wavelength Lank xxxxxx xxxxxx LEF: FoLwaLd Voltage Lank RoHS xxxxxxxxxxxx xxxx xxxxxxxx Leel Dimensions Note: The toleLances unless mentioned is ±0.1mm ,Unit = mm Everlight Electronics Co., Ltd. Device No:SZDSE-197-G01 http://www.everlight.com Prepared date: 17-10-2006 Rev. 2 Page: 6 of 10 Prepared by: Bian ChangYou EVERLIGHT ELECTRONICS CO.,LTD. 19-217/G7C-AL1M2B/3T CaLLieL Tape Dimensions: Loaded quantity 3000 PCS peL Leel Note: The toleLances unless mentioned is ±0.1mm ,Unit = mm MoistuLe Lesistant Packaging Label Aluminum moistue-proof bag Everlight Electronics Co., Ltd. Device No:SZDSE-197-G01 http://www.everlight.com Prepared date: 17-10-2006 Desiccant Label Rev. 2 Page: 7 of 10 Prepared by: Bian ChangYou EVERLIGHT ELECTRONICS CO.,LTD. 19-217/G7C-AL1M2B/3T Leliability Test Items And Conditions The Leliability of pLoducts shall be satisfied with items listed below. Confidence level：90% LTPD：10% Test Sample HouLs/Cycle Size s No. Items Test Condition 1 Leflow SoldeLing Temp. : 260℃±5℃ Min. 5sec. 6 Min. 22 PCS. 0/1 TempeLatuLe Cycle H : +100℃ 15min ∫ 5 min L : -40℃ 15min 300 Cycles 22 PCS. 0/1 TheLmal Shock H : +100℃ 5min ∫ 10 sec L : -10℃ 5min 300 Cycles 22 PCS. 0/1 Temp. : 100℃ 1000 HLs. 22 PCS. 0/1 Temp. : -40℃ 1000 HLs. 22 PCS. 0/1 2 3 4 5 High TempeLatuLe StoLage Low TempeLatuLe StoLage Ac/Le 6 DC OpeLating Life IF = 20 mA 1000 HLs. 22 PCS. 0/1 7 High TempeLatuLe / High Humidity 85℃/ 85%RH 1000 HLs. 22 PCS. 0/1 Everlight Electronics Co., Ltd. Device No:SZDSE-197-G01 http://www.everlight.com Prepared date: 17-10-2006 Rev. 2 Page: 8 of 10 Prepared by: Bian ChangYou EVERLIGHT ELECTRONICS CO.,LTD. 19-217/G7C-AL1M2B/3T PLecautions FoL Use 1. Over-current-proof Customer must apply resistors for protection, otherwise slight voltage shift will cause big current change ( Burn out will happen ). 2. Storage 2.1 Do not open moisture proof bag before the products are ready to use. 2.2 Before opening the package: The LEDs should be kept at 30℃ or less and 90%RH or less. 2.3 After opening the package: The LED's floor life is 1 year under 30℃ or less and 60% RH or less. If unused LEDs remain, it should be stored in moisture proof packages. 2.4 If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded the storage time, baking treatment should be performed using the following conditions. Baking treatment : 60±5℃ for 24 hours. 3. Soldering Condition 3.1 Pb-free solder temperature profile 3.2 Reflow soldering should not be done more than two times. 3.3 When soldering, do not put stress on the LEDs during heating. 3.4 After soldering, do not warp the circuit board. Everlight Electronics Co., Ltd. Device No:SZDSE-197-G01 http://www.everlight.com Prepared date: 17-10-2006 Rev. 2 Page: 9 of 10 Prepared by: Bian ChangYou EVERLIGHT ELECTRONICS CO.,LTD. 19-217/G7C-AL1M2B/3T 4.Soldering Iron Each terminal is to go to the tip of soldering iron temperature less than 350℃ for 3 seconds within once in less than the soldering iron capacity 25W. Leave two seconds and more intervals, and do soldering of each terminal. Be careful because the damage of the product is often started at the time of the hand solder. 5.Repairing Repair should not be done after the LEDs have been soldered. When repairing is unavoidable, a double-head soldering iron should be used (as below figure). It should be confirmed beforehand whether the characteristics of the LEDs will or will not be damaged by repairing. EVERLIGHT ELECTRONICS CO., LTD. Office: No 25, Lane 76, Sec 3, Chung Yang Rd, Leliability AndR.O.C Conditions Tucheng,Test TaipeiItems 236, Taiwan, Tel: 886-2-2267-2000, 2267-9936 Fax: 886-2267-6244, 2267-6189, 2267-6306 http://www.everlight.com The Leliability of pLoducts shall be satisfied with items listed below. Everlight Electronics Co., Ltd. Device No:SZDSE-197-G01 http://www.everlight.com Prepared date: 17-10-2006 Rev. 2 Page: 10 of 10 Prepared by: Bian ChangYou