19-217-G7C-AL1M2B-3T

EVERLIGHT ELECTRONICS CO.,LTD. Technical Data Sheet 0603 Package Chip LED(0.4mm Height) 19-217/G7C-AL1M2B/3T Features ․Package in 8mm tape on 7〞diameter reel. ․Compatible with automatic placement equipment. ․Compatible with infrared and vapor phase reflow solder process. ․Mono-color type. ․Pb-free. ․The product itself will remain within RoHS complaint version Descriptions ․The 19-217 SMD Taping is much smaller than lead frame type components, thus enable smaller board size, higher packing density, reduced storage space and finally smaller equipment to be obtained. ․ Besides, lightweight makes them ideal for miniature applications. etc. Applications ․Backlighting in dashboard and switch. ․Telecommunication: indicator and backlighting in telephone and fax. ․Flat backlight for LCD, switch and symbol. ․General use. Device Selection Guide Part No. 19-217/G7C-AL1M2B/3T Chip Material AlGaInP Emitted Color Brilliant Yellow Green Lens Color Water Clear Everlight Electronics Co., Ltd. Device No:SZDSE-197-G01 http://www.everlight.com Prepared date: 17-10-2006 Rev. 2 Page: 1 of 10 Prepared by: Bian ChangYou EVERLIGHT ELECTRONICS CO.,LTD. 19-217/G7C-AL1M2B/3T Package Outline Dimensions Note: The tolerances unless mentioned is ±0.1mm ,Unit Everlight Electronics Co., Ltd. Device No:SZDSE-197-G01 http://www.everlight.com Prepared date: 17-10-2006 Rev. 2 Page: 2 of 10 Prepared by: Bian ChangYou EVERLIGHT ELECTRONICS CO.,LTD. 19-217/G7C-AL1M2B/3T Absolute Maximum Ratings (Ta=25℃) Parameter Reverse Voltage Forward Current Peak Forward Current (Duty 1/10 @1KHz) Power Dissipation Electrostatic Discharge(HBM) Operating Temperature Storage Temperature Soldering Temperature Symbol VR IF IFP Pd ESD Topr Tstg Tsol Rating 5 25 60 60 2000 -40 ~ +85 -40 ~ +90 Unit V mA mA mW V ℃ ℃ Reflow Soldering : 260 ℃ for 10 sec. Hand Soldering : 350 ℃ for 3 sec. Electro-Optical Characteristics (Ta=25℃) Parameter Luminous Intensity Viewing Angle Peak Wavelength Dominant Wavelength Spectrum Radiation Bandwidth Forward Voltage Reverse Current Symbol Iv 2θ1/2 λp λd △λ VF IR Min. 11.5 --------569.5 ----1.75 ----Typ. ----120 575 ----20 --------Max. 28.5 --------577.5 ----2.35 10 Unit mcd deg nm nm nm V μA VR=5V IF=20mA Condition Notes: 1.Tolerance of Luminous Intensity ±10% 2.Tolerance of Dominant Wavelength ±1nm 3.Tolerance of Forward Voltage ±0.1V Everlight Electronics Co., Ltd. Device No:SZDSE-197-G01 http://www.everlight.com Prepared date: 17-10-2006 Rev. 2 Page: 3 of 10 Prepared by: Bian ChangYou EVERLIGHT ELECTRONICS CO.,LTD. 19-217/G7C-AL1M2B/3T Bin Range Of Dom. Wavelength Group Bin C16 A C17 C18 C19 Bin L1 L2 M1 M2 Group Bin 0 B 1 2 Min 11.5 14.5 18.0 22.5 Min 1.75 1.95 2.15 Min 569.5 571.5 573.5 575.5 Max 571.5 573.5 575.5 577.5 Max 14.5 18.0 22.5 28.5 Max 1.95 2.15 2.35 V IF=20mA Unit Condition mcd IF=20mA Unit Condition nm IF=20mA Unit Condition Bin Range Of Luminous Intensity Bin Range Of Forward Voltage Notes: 1.ToleLance of Luminous Intensity ±10% 2.ToleLance of Dominant Wavelength ±1nm 3.ToleLance of FoLwaLd Voltage ±0.1V Everlight Electronics Co., Ltd. Device No:SZDSE-197-G01 http://www.everlight.com Prepared date: 17-10-2006 Rev. 2 Page: 4 of 10 Prepared by: Bian ChangYou EVERLIGHT ELECTRONICS CO.,LTD. 19-217/G7C-AL1M2B/3T Typical ElectLo-Optical ChaLacteListics CuLves Everlight Electronics Co., Ltd. Device No:SZDSE-197-G01 http://www.everlight.com Prepared date: 17-10-2006 Rev. 2 Page: 5 of 10 Prepared by: Bian ChangYou EVERLIGHT ELECTRONICS CO.,LTD. 19-217/G7C-AL1M2B/3T Label explanation CAT: Luminous Intensity Lank HUE: Dom. Wavelength Lank LEF: FoLwaLd Voltage Lank xxxxxx xxxxxx RoHS xxxxxxxxxxxx xxxx xxxxxxxx Leel Dimensions Note: The toleLances unless mentioned is ±0.1mm ,Unit = mm Everlight Electronics Co., Ltd. Device No:SZDSE-197-G01 http://www.everlight.com Prepared date: 17-10-2006 Rev. 2 Page: 6 of 10 Prepared by: Bian ChangYou EVERLIGHT ELECTRONICS CO.,LTD. 19-217/G7C-AL1M2B/3T CaLLieL Tape Dimensions: Loaded quantity 3000 PCS peL Leel Note: The toleLances unless mentioned is ±0.1mm ,Unit = mm MoistuLe Lesistant Packaging Label Aluminum moistue-proof bag Desiccant Label Everlight Electronics Co., Ltd. Device No:SZDSE-197-G01 http://www.everlight.com Prepared date: 17-10-2006 Rev. 2 Page: 7 of 10 Prepared by: Bian ChangYou EVERLIGHT ELECTRONICS CO.,LTD. 19-217/G7C-AL1M2B/3T Leliability Test Items And Conditions The Leliability of pLoducts shall be satisfied with items listed below. Confidence level：90% LTPD：10% No. Items Test Condition Temp. : 260℃±5℃ Min. 5sec. H : +100℃ 15min ∫ 5 min L : -40℃ 15min H : +100℃ 5min ∫ 10 sec L : -10℃ 5min Temp. : 100℃ Temp. : -40℃ IF = 20 mA 85℃/ 85%RH Test Sample HouLs/Cycle Size s 6 Min. 300 Cycles 22 PCS. Ac/Le 1 Leflow SoldeLing 0/1 2 TempeLatuLe Cycle 22 PCS. 0/1 3 4 5 6 7 TheLmal Shock High TempeLatuLe StoLage Low TempeLatuLe StoLage DC OpeLating Life High TempeLatuLe / High Humidity 300 Cycles 1000 HLs. 1000 HLs. 1000 HLs. 1000 HLs. 22 PCS. 22 PCS. 22 PCS. 22 PCS. 22 PCS. 0/1 0/1 0/1 0/1 0/1 Everlight Electronics Co., Ltd. Device No:SZDSE-197-G01 http://www.everlight.com Prepared date: 17-10-2006 Rev. 2 Page: 8 of 10 Prepared by: Bian ChangYou EVERLIGHT ELECTRONICS CO.,LTD. 19-217/G7C-AL1M2B/3T PLecautions FoL Use 1. Over-current-proof Customer must apply resistors for protection, otherwise slight voltage shift will cause big current change ( Burn out will happen ). 2. Storage 2.1 Do not open moisture proof bag before the products are ready to use. 2.2 Before opening the package: The LEDs should be kept at 30℃ or less and 90%RH or less. 2.3 After opening the package: The LED's floor life is 1 year under 30℃ or less and 60% RH or less. If unused LEDs remain, it should be stored in moisture proof packages. 2.4 If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded the storage time, baking treatment should be performed using the following conditions. Baking treatment : 60±5℃ for 24 hours. 3. Soldering Condition 3.1 Pb-free solder temperature profile 3.2 Reflow soldering should not be done more than two times. 3.3 When soldering, do not put stress on the LEDs during heating. 3.4 After soldering, do not warp the circuit board. Everlight Electronics Co., Ltd. Device No:SZDSE-197-G01 http://www.everlight.com Prepared date: 17-10-2006 Rev. 2 Page: 9 of 10 Prepared by: Bian ChangYou EVERLIGHT ELECTRONICS CO.,LTD. 19-217/G7C-AL1M2B/3T 4.Soldering Iron Each terminal is to go to the tip of soldering iron temperature less than 350℃ for 3 seconds within once in less than the soldering iron capacity 25W. Leave two seconds and more intervals, and do soldering of each terminal. Be careful because the damage of the product is often started at the time of the hand solder. 5.Repairing Repair should not be done after the LEDs have been soldered. When repairing is unavoidable, a double-head soldering iron should be used (as below figure). It should be confirmed beforehand whether the characteristics of the LEDs will or will not be damaged by repairing. EVERLIGHT ELECTRONICS CO., LTD. Office: No 25, Lane 76, Sec 3, Chung Yang Rd, Leliability Test Items AndR.O.C Tucheng, Taipei 236, Taiwan, Conditions Tel: 886-2-2267-2000, 2267-9936 Fax: 886-2267-6244, 2267-6189, 2267-6306 http://www.everlight.com The Leliability of pLoducts shall be satisfied with items listed below. Everlight Electronics Co., Ltd. Device No:SZDSE-197-G01 http://www.everlight.com Prepared date: 17-10-2006 Rev. 2 Page: 10 of 10 Prepared by: Bian ChangYou