26-21SYGC/S530-E2/TR8

SMD  B 26-21SYGC/S530-E2/TR8 Features ․Package in 8mm tape on 7〞diameter reel. ․Compatible with automatic placement equipment. ․Compatible with infrared and vapor phase reflow solder process. ․Mono-color type. ․Pb-free. ․The product itself will remain within RoHS compliant version. Description ․The 26-21 SMD LED is much smaller than lead frame type components, thus enable smaller board size, higher packing density, reduced storage space and finally smaller equipment to be obtained. ․Besides, lightweight makes them ideal for miniature applications. etc. Applications ․Telecommunication: indicator and backlighting in telephone and fax. ․Flat backlight for LCD, switch and symbol. ․General use. 1 Copyright © 2013, Everlight All Rights Reserved. Release Date : May.20.2013. Issue No: DSE-0008961 Rev.2 www.everlight.com DATASHEET SMD  REFLECTOR 26-21SYGC/S530-E2/TR8 Device Selection Guide Chip Materials AlGaInP Emitted Color Resin Color Brilliant Yellow Green Water Clear Absolute Maximum Ratings (Ta=25℃) Parameter Symbol Rating Unit Reverse Voltage VR 5 V IF 25 mA IFP 60 mA Power Dissipation Pd 60 mW Operating Temperature Topr -40 ~ +85 ℃ Storage Temperature Tstg -40 ~ +90 ℃ Electrostatic Discharge ESDHBM 2000 V Soldering Temperature Tsol Forward Current Peak Forward Current (Duty 1/10 @1KHz) Reflow Soldering : 260 ℃ for 30 sec. Hand Soldering : 350 ℃ for 3 sec. Electro-Optical Characteristics (Ta=25℃) Parameter Symbol Min. Typ. Max. Unit Luminous Intensity Iv 200 315 ----- mcd Viewing Angle 2θ1/2 ----- 30 ------ deg Peak Wavelength ----- 575 ------ nm ----- 573 ------ nm Spectrum Radiation Bandwidth λ p λ d △λ ----- 20 ------ nm Forward Voltage VF ----- 2.0 2.4 V Reverse Current IR ----- ----- 10 μA Dominant Wavelength 2 Copyright © 2013, Everlight All Rights Reserved. Release Date : May.20.2013 Issue No: DSE-0008961 Rev.2 Condition IF=20mA VR=5V www.everlight.com DATASHEET SMD  REFLECTOR 26-21SYGC/S530-E2/TR8 Typical Electro-Optical Characteristics Curves 3 Copyright © 2013, Everlight All Rights Reserved. Release Date : May.20.2013 Issue No: DSE-0008961 Rev.2 www.everlight.com DATASHEET SMD  REFLECTOR 26-21SYGC/S530-E2/TR8 Package Outline Dimensions Note: Tolerances unless mentioned ±0.1mm. Unit = mm Suggested pad dimension is just for reference only. Please modify the pad dimension based on individual need. 4 Copyright © 2013, Everlight All Rights Reserved. Release Date : May.20.2013 Issue No: DSE-0008961 Rev.2 www.everlight.com DATASHEET SMD  REFLECTOR 26-21SYGC/S530-E2/TR8 Moisture Resistant Packing Materials Label Explanation ‧CAT: Luminous Intensity Rank ‧HUE: Dom. Wavelength Rank ‧REF: Forward Voltage Rank Reel Dimensions Note: The tolerances unless mentioned is ±0.1mm ,Unit = mm 5 Copyright © 2013, Everlight All Rights Reserved. Release Date : May.20.2013 Issue No: DSE-0008961 Rev.2 www.everlight.com DATASHEET SMD  REFLECTOR 26-21SYGC/S530-E2/TR8 Carrier Tape Dimensions: Loaded quantity 1500 PCS per reel Note: The tolerances unless mentioned is ±0.1mm ,Unit = mm Moisture Resistant Packaging Label 6 Aluminum moisture-proof bag Desiccant Label Copyright © 2013, Everlight All Rights Reserved. Release Date : May.20.2013 Issue No: DSE-0008961 Rev.2 www.everlight.com DATASHEET SMD  REFLECTOR 26-21SYGC/S530-E2/TR8 Precautions For Use 1. Over-current-proof Customer must apply resistors for protection, otherwise slight voltage shift will cause big current change ( Burn out will happen ). 2. Storage 2.1 Do not open moisture proof bag before the products are ready to use. 2.2 Before opening the package: The LEDs should be kept at 30℃ or less and 90%RH or less. 2.3 After opening the package: The LED's floor life is 1 year under 30℃ or less and 60% RH or less. If unused LEDs remain, it should be stored in moisture proof packages. 2.4 If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded the storage time, baking treatment should be performed using the following conditions. Baking treatment : 60±5℃ for 24 hours. 3. Soldering Condition 3.1 Pb-free solder temperature profile 260°C Max. 10sec. Max. Above255°C 30sec.Max. 3°C/sec.Max. 6°C/sec.Max. Pre-heating Above 217°C 60~150sec. 150~200°C 60~120sec. 3.2 Reflow soldering should not be done more than two times. 3.3 When soldering, do not put stress on the LEDs during heating. 3.4 After soldering, do not warp the circuit board. 7 Copyright © 2013, Everlight All Rights Reserved. Release Date : May.20.2013 Issue No: DSE-0008961 Rev.2 www.everlight.com DATASHEET SMD  REFLECTOR 26-21SYGC/S530-E2/TR8 4.Soldering Iron Each terminal is to go to the tip of soldering iron temperature less than 350℃ for 3 seconds within once in less than the soldering iron capacity 25W. Leave two seconds and more intervals, and do soldering of each terminal. Be careful because the damage of the product is often started at the time of the hand solder. 5.Repairing Repair should not be done after the LEDs have been soldered. When repairing is unavoidable, a double-head soldering iron should be used (as below figure). It should be confirmed beforehand whether the characteristics of the LEDs will or will not be damaged by repairing. EVERLIGHT ELECTRONICS CO., LTD. Office: No 25, Lane 76, Sec 3, Chung Yang Rd, Tucheng, Taipei 236, Taiwan, R.O.C 8 Tel: 886-2-2267-2000, 2267-9936 Fax: 886-2267-6244, 2267-6189, 2267-6306 http://www.everlight.com Copyright © 2013, Everlight All Rights Reserved. Release Date : May.20.2013 Issue No: DSE-0008961 Rev.2 www.everlight.com