334-15-T2C1-1UWA

Technical Data Sheet 334-15/T2C1-1UWA Features ․Popular T-1 3/4 round package ․High luminous power. ․Typical chromaticity coordinates x=0.29, y=0.28 according to CIE1931. ․Bulk, available taped on reel. ․ESD-withstand voltage: up to 4KV ․The product itself will remain within RoHS compliant version. Descriptions ․The series is designed for application required high luminous intensity. ․The phosphor filled in the reflector converts the blue emission of InGaN chip to ideal white. Applications ․Message panels ․Optical Indicators ․Backlighting ․Marker Lights Device Selection Guide Chip PART NO. Material 334-15/T2C1-1UWA InGaN Emitted Color White Water Clear Lens Color Everlight Electronics Co., Ltd. Device Number: DLE-0000657 http\\:www.everlight.com Established date:12-18-2008 Rev 1 Page: 1 of12 Established by: Ruby Lin Technical Data Sheet 334-15/T2C1-1UWA Package Dimensions Notes: 1.All dimensions are in millimeters, and tolerance is 0.25mm except being specified. 2.Lead spacing is measured where the lead emerges from the package. 3.Protruded resin under flange is 1.5mm Max. LED. Everlight Electronics Co., Ltd. Device Number: DLE-0000657 http\\:www.everlight.com Established date:12-18-2008 Rev 1 Page: 2 of12 Established by: Ruby Lin Technical Data Sheet 334-15/T2C1-1UWA Absolute Maximum Ratings (Ta=25℃) Parameter Continuous Forward Current Peak Forward Current(Duty /10 @ 1KHZ) Reverse Voltage Operating Temperature Storage Temperature Soldering Temperature (T=5 sec) Power Dissipation Zener Reverse Current Electrostatic Discharge Symbol IF IFP VR Topr Tstg Tsol Pd Iz ESD Rating 30 100 5 -40 ~ +85 -40 ~ +100 260 110 100 4K Unit mA mA V ℃ ℃ ℃ mW mA V Everlight Electronics Co., Ltd. Device Number: DLE-0000657 http\\:www.everlight.com Established date:12-18-2008 Rev 1 Page: 3 of12 Established by: Ruby Lin Technical Data Sheet 334-15/T2C1-1UWA Production Designation 334-15/T2C1-□ □ □ □ Voltage Group Luminous Intensity Bins Color Group Electro-Optical Characteristics (Ta=25℃) Parameter Forward Voltage Zener Reverse Voltage Reverse Current Luminous Intensity Viewing Angle Symbol VF Vz IR IV 2θ1/2 x Chromaticity Coordinates y IF=20mA -0.28 --Condition IF=20mA Iz=5mA VR=5V IF=20mA IF=20mA Min. 2.8 5.2 -9000 --15 0.29 Typ. -------Max. 3.6 ----50 18000 --Units V V uA mcd deg -- Everlight Electronics Co., Ltd. Device Number: DLE-0000657 http\\:www.everlight.com Established date:12-18-2008 Rev 1 Page: 4 of12 Established by: Ruby Lin Technical Data Sheet 334-15/T2C1-1UWA Luminous Intensity Combination (mcd at 20mA) Rank U V W Min 9000 11250 14250 Max 11250 14250 18000 *Measurement Uncertainty of Luminous Intensity: ±10% Forward Voltage Combination (V at 20mA) Rank Forward Voltage 0 2.8~3.0 1 3.0~3.2 2 3.2~3.4 3 3.4~3.6 *Measurement Uncertainty of Forward Voltage：±0.1V Color Combination ( at 20mA) Group 1 Bins A1+A0+B3+B4+B5+B6+C0 Everlight Electronics Co., Ltd. Device Number: DLE-0000657 http\\:www.everlight.com Established date:12-18-2008 Rev 1 Page: 5 of12 Established by: Ruby Lin Technical Data Sheet 334-15/T2C1-1UWA CIE Chromaticity Diagram 0 .8 0 .6 CIE-Y 56 00K 700 0K 46 00K 0 .4 9 00 0K 1 40 00 K 2 200 0K B4 B3 AO B5 CO B6 A1 0 .2 0 .0 0 .0 0 .1 0 .2 0 .3 0 .4 0 .5 0.6 0 .7 C IE -X Color Ranks (IF=20mA，Ta=25℃) Color Ranks A1 A0 B3 B4 B5 B6 C0 X Y X Y X Y X Y X Y X Y X 0.255 0.245 0.264 0.267 0.283 0.305 0.304 0.33 0.287 0.295 0.307 0.315 0.33 0.264 0.267 0.283 0.305 0.304 0.33 0.33 0.36 0.307 0.315 0.33 0.339 0.361 CIE 0.28 0.248 0.296 0.267 0.307 0.315 0.33 0.339 0.311 0.294 0.33 0.318 0.355 0.35 0.27 0.23 0.28 0.248 0.287 0.295 0.307 0.315 0.296 0.276 0.311 0.294 0.33 0.318 Y 0.36 0.385 Measurement uncertainty of the color coordinates：±0.01 Everlight Electronics Co., Ltd. Device Number: DLE-0000657 http\\:www.everlight.com Established date:12-18-2008 Rev 1 Page: 6 of12 Established by: Ruby Lin Technical Data Sheet 334-15/T2C1-1UWA Typical Electro-Optical Characteristics Curves Relative Intensity vs. Wavelength 1.0 Forward Current vs. Forward Voltage 25 Forward Current(mA) Relative Intensity(a.u.) 20 0.8 15 0.6 10 0.4 5 0.2 0.0 350 0 1.5 400 450 500 550 600 650 700 750 800 2.0 2.5 3.0 3.5 4.0 4.5 Wavelength(nm) Forward Voltage(V) Relative Intensity vs. Forward Current 1.5 Forward Current vs. Ambient Temp. 40 Relative Intensity(a.u.) Forward Current(mA) 30 1.0 20 0.5 10 0.0 0 0 5 10 15 20 25 0 20 40 60 80 O 100 Forward Current(mA) Ambient Temperature Ta( C) Chromaticity Coordinate vs. Forward Current 0.300 Relative Intensity vs. Angle Displacement 90 O 60 O 30 O 0 O 10O Relative Intensity(a.u.) Relative Luminusity 0.290 x y 1.0 20 O 30 O 40 O O 50 0.5 0.280 60 O 0.270 70 O 80 0 O 0.260 0 10 20 30 40 50 Forward Current(mA) 0 0.5 90 1.0 O Radiation Angle http\\:www.everlight.com Established date:12-18-2008 Rev 1 Page: 7 of12 Everlight Electronics Co., Ltd. Device Number: DLE-0000657 Established by: Ruby Lin Technical Data Sheet 334-15/T2C1-1UWA Packing Specification Anti-electrostatic bag Inner Carton Outside Carton Everlight Electronics Co., Ltd. Device Number: DLE-0000657 http\\:www.everlight.com Established date:12-18-2008 ■ ■ CITE NGA NORTCELE C IT ATS ORTCE LE SDLER EV ITCA OI DAR RO C ITEN GAM 057 rof c itats- itna bP ■ ■ ■ Label Label Form Specification CPN: Customer’s Production Number P/N : Production Number QTY: Packing Quantity CAT: Ranks of Luminous Intensity and Forward Voltage HUE: Color Rank REF: Reference LOT No: Lot Number MADE IN TAIWAN: Production Place Packing Quantity 1. 500 PCS/1 Bag, 5 Bags/1 Inner Carton 2. 10 Inner Cartons/1 Outside Carton Rev 1 Page: 8 of12 Established by: Ruby Lin Technical Data Sheet 334-15/T2C1-1UWA Notes 1. Lead Forming During lead formation, the leads should be bent at a point at least 3mm from the base of the epoxy bulb. Lead forming should be done before soldering. Avoid stressing the LED package during leads forming. The stress to the base may damage the LED’s characteristics or it may break the LEDs. Cut the LED leadframes at room temperature. Cutting the leadframes at high temperatures may cause failure of the LEDs. When mounting the LEDs onto a PCB, the PCB holes must be aligned exactly with the lead position of the LED. If the LEDs are mounted with stress at the leads, it causes deterioration of the epoxy resin and this will degrade the LEDs. 2. Storage The LEDs should be stored at 30°C or less and 70%RH or less after being shipped from Everlight and the storage life limits are 3 months. If the LEDs are stored for 3 months or more, they can be stored for a year in a sealed container with a nitrogen atmosphere and moisture absorbent material. Please avoid rapid transitions in ambient temperature, especially, in high humidity environments where condensation can occur. 3. Soldering Careful attention should be paid during soldering. When soldering, leave more then 3mm from solder joint to epoxy bulb, and soldering beyond the base of the tie bar is recommended. Recommended soldering conditions: Hand Soldering Temp. at tip of 300℃ Max. (30W iron Max.) Soldering time 3 sec Max. Distance 3mm Min.(From solder joint to epoxy bulb) Everlight Electronics Co., Ltd. Device Number: DLE-0000657 DIP Soldering 100℃ Max. (60 sec Preheat temp. Max.) Bath temp. & time 260 Max., 5 sec Max Distance 3mm Min. (From solder joint to epoxy bulb) Rev 1 Page: 9 of12 http\\:www.everlight.com Established date:12-18-2008 Established by: Ruby Lin Technical Data Sheet 334-15/T2C1-1UWA laminar wave Fluxing Prehead Avoiding applying any stress to the lead frame while the LEDs are at high temperature particularly when soldering. Dip and hand soldering should not be done more than one time After soldering the LEDs, the epoxy bulb should be protected from mechanical shock or vibration until the LEDs return to room temperature. A rapid-rate process is not recommended for cooling the LEDs down from the peak temperature. Although the recommended soldering conditions are specified in the above table, dip or handsoldering at the lowest possible temperature is desirable for the LEDs. Wave soldering parameter must be set and maintain according to recommended temperature and dwell time in the solder wave. 4. Cleaning When necessary, cleaning should occur only with isopropyl alcohol at room temperature for a duration of no more than one minute. Dry at room temperature before use. Do not clean the LEDs by the ultrasonic. When it is absolutely necessary, the influence of ultrasonic cleaning on the LEDs depends on factors such as ultrasonic power and the assembled condition. Ultrasonic cleaning shall be pre-qualified to ensure this will not cause damage to the LED Everlight Electronics Co., Ltd. Device Number: DLE-0000657 http\\:www.everlight.com Established date:12-18-2008 Rev 1 Page: 10 of12 Established by: Ruby Lin Technical Data Sheet 334-15/T2C1-1UWA 5. Circuit Protection Below the zener reference voltage Vz, all the current flows through LED and as the voltage rises to Vz, the zener diode “breakdown." If the voltage tries to rise above Vz current flows through the zener branch to keep the voltage at exactly Vz. When the LED is connected using serial circuit, if either piece of LED is no light up but current can’t flow through causing others to light down. In new design, the LED is parallel with zener diode. if either piece of LED is no light up but current can flow through causing others to light up. 6. Heat Management Heat management of LEDs must be taken into consideration during the design stage of LED application. The current should be de-rated appropriately by referring to the de-rating curve found in each product specification. The temperature surrounding the LED in the application should be controlled. Please refer to the data sheet de-rating curve. Everlight Electronics Co., Ltd. Device Number: DLE-0000657 http\\:www.everlight.com Established date:12-18-2008 Rev 1 Page: 11 of12 Established by: Ruby Lin Technical Data Sheet 334-15/T2C1-1UWA 7. ESD (Electrostatic Discharge) Electrostatic discharge (ESD) or surge current (EOS) can damage LEDs. An ESD wrist strap, ESD shoe strap or antistatic gloves must be worn whenever handling LEDs. All devices, equipment and machinery must be properly grounded. Use ion blower to neutralize the static charge which might have built up on surface of the LEDs plastic lens as a result of friction between LEDs during storage and handing. 8. Other Above specification may be changed without notice. EVERLIGHT will reserve authority on material change for above specification. When using this product, please observe the absolute maximum ratings and the instructions for using outlined in these specification sheets. EVERLIGHT assumes no responsibility for any damage resulting from use of the product which does not comply with the absolute maximum ratings and the instructions included in these specification sheets. These specification sheets include materials protected under copyright of EVERLIGHT corporation. Please don’t reproduce or cause anyone to reproduce them without EVERLIGHT’s consent. EVERLIGHT ELECTRONICS CO., LTD. Office: No 25, Lane 76, Sec 3, Chung Yang Rd, Tucheng, Taipei 236, Taiwan, R.O.C Tel: 886-2-2267-2000, 2267-9936 Fax: 886-2267-6244, 2267-6189, 2267-6306 http:\\www.everlight.com Everlight Electronics Co., Ltd. Device Number: DLE-0000657 http\\:www.everlight.com Established date:12-18-2008 Rev 1 Page: 12 of12 Established by: Ruby Lin