42-21/BHC-AUW/1T

SMD  B 42-21/BHC-AUW/1T Features ․Package in 8mm tape on 7〞diameter reel. ․Compatible with automatic placement equipment. ․Compatible with infrared and vapor phase reflow solder process. ․Mono-color type. ․Pb-free. ․The product itself will remain within RoHS compliant version. Description ․The 42-21 SMD LED is much smaller than lead frame type components, thus enable smaller board ize, higher packing density, reduced storage space and finally smaller equipment to be obtained. ․Besides, lightweight makes them ideal for miniature applications. etc. Applications ․Telecommunication: indicator and backlighting in telephone and fax. ․Flat backlight for LCD, switch and symbol. ․General use. 1 Copyright © 2010, Everlight All Rights Reserved. Release Date : 26-Apr-2013. Issue No: DSE-0008851 Rev.3 www.everlight.com DATASHEET SMD  REFLECTOR 42-21/BHC-AUW/1T Device Selection Guide Chip Materials InGaN Emitted Color Resin Color Blue Water clear Absolute Maximum Ratings (Ta=25℃) Parameter Symbol Rating Unit Reverse Voltage VR 5 V IF 25 mA IFP 100 mA Power Dissipation Pd 95 mW Operating Temperature Topr -40 ~ +85 ℃ Storage Temperature Tstg -40 ~ +90 ℃ Electrostatic Discharge ESDHBM 150 V Soldering Temperature Tsol Forward Current Peak Forward Current (Duty 1/10 @1KHz) Reflow Soldering : 260 ℃ for 10 sec. Hand Soldering : 350 ℃ for 3 sec. Electro-Optical Characteristics (Ta=25℃) Parameter Symbol Min. Typ. Max. Unit Condition Luminous Intensity Iv 450 ----- 1800 mcd IF=20mA Viewing Angle 2θ1/2 ----- 30 ----- deg IF=20mA Peak Wavelength ----- 468 ----- nm IF=20mA 464.5 ----- 476.5 nm IF=20mA Spectrum Radiation Bandwidth λp λd △λ ----- 25 ----- nm IF=20mA Forward Voltage VF 2.7 3.3 3.7 V IF=20mA Reverse Current IR ----- ----- 50 μA VR=5V Dominant Wavelength Notes: 1.Tolerance of Luminous Intensity ±11nm 2.Tolerance of Dominant Wavelength±1nm 2 Copyright © 2010, Everlight All Rights Reserved. Release Date : 26-Apr-2013. Issue No: DSE-0008851 Rev.3 www.everlight.com DATASHEET SMD  REFLECTOR 42-21/BHC-AUW/1T Bin Range of Luminous Intensity Bin Code Min. Max. Unit Condition U V W 450 715 1120 715 1120 1800 mcd IF =20mA Note: Tolerance of Luminous Intensity: ±11% Bin Range of Dominant Wavelength Group Bin Code Min. Max. Unit Condition A A9 A10 A11 A12 464.5 467.5 470.5 473.5 467.5 470.5 473.5 476.5 nm IF =20mA Notes: 1.Tolerance of Luminous Intensity ±11% 2.Tolerance of Dominant Wavelength ±1nm 3 Copyright © 2010, Everlight All Rights Reserved. Release Date : 26-Apr-2013. Issue No: DSE-0008851 Rev.3 www.everlight.com DATASHEET SMD  REFLECTOR 42-21/BHC-AUW/1T v 4 Copyright © 2010, Everlight All Rights Reserved. Release Date : 26-Apr-2013. Issue No: DSE-0008851 Rev.3 www.everlight.com DATASHEET SMD  REFLECTOR 42-21/BHC-AUW/1T Note: The tolerances unless mentioned is ±0.1mm ,Unit = mm 5 Copyright © 2010, Everlight All Rights Reserved. Release Date : 26-Apr-2013. Issue No: DSE-0008851 Rev.3 www.everlight.com DATASHEET SMD  REFLECTOR 42-21/BHC-AUW/1T Moisture Resistant Packing Materials Label Explanation ‧CPN: Customer’s Product Number ‧P/N: Product Number ‧QTY: Packing Quantity ‧CAT: Luminous Intensity Rank ‧HUE: Chromaticity Coordinates & Dom. Wavelength Rank ‧REF: Forward Voltage Rank ‧LOT No: Lot Number Reel Dimensions Note: The tolerances unless mentioned is ±0.1mm ,Unit = mm 6 Copyright © 2010, Everlight All Rights Reserved. Release Date : 26-Apr-2013. Issue No: DSE-0008851 Rev.3 www.everlight.com DATASHEET SMD  REFLECTOR 42-21/BHC-AUW/1T Carrier Tape Dimensions: Loaded quantity 1000 PCS per reel Note: The tolerances unless mentioned is ±0.1mm ,Unit = mm Moisture Resistant Packaging Label 7 Aluminum moisture-proof bag Desiccant Label Copyright © 2010, Everlight All Rights Reserved. Release Date : 26-Apr-2013. Issue No: DSE-0008851 Rev.3 www.everlight.com DATASHEET SMD  REFLECTOR 42-21/BHC-AUW/1T Precautions For Use 1. Over-current-proof Customer must apply resistors for protection, otherwise slight voltage shift will cause big current change ( Burn out will happen ). 2. Storage 2.1 Do not open moisture proof bag before the products are ready to use. 2.2 Before opening the package: The LEDs should be kept at 30℃ or less and 90%RH or less. 2.3 After opening the package: The LED's floor life is 1 year under 30℃ or less and 60% RH or less. If unused LEDs remain, it should be stored in moisture proof packages. 2.4 If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded the storage time, baking treatment should be performed using the following conditions. Baking treatment : 60±5℃ for 24 hours. 3. Soldering Condition 3.1 Pb-free solder temperature profile 3.2 Reflow soldering should not be done more than two times. 3.3 When soldering, do not put stress on the LEDs during heating. 3.4 After soldering, do not warp the circuit board. 8 Copyright © 2010, Everlight All Rights Reserved. Release Date : 26-Apr-2013. Issue No: DSE-0008851 Rev.3 www.everlight.com DATASHEET SMD  REFLECTOR 42-21/BHC-AUW/1T 4.Soldering Iron Each terminal is to go to the tip of soldering iron temperature less than 350℃ for 3 seconds within once in less than the soldering iron capacity 25W. Leave two seconds and more intervals, and do soldering of each terminal. Be careful because the damage of the product is often started at the time of the hand solder. 5.Repairing Repair should not be done after the LEDs have been soldered. When repairing is unavoidable, a double-head soldering iron should be used (as below figure). It should be confirmed beforehand whether the characteristics of the LEDs will or will not be damaged by repairing. EVERLIGHT ELECTRONICS CO., LTD. Office: No 25, Lane 76, Sec 3, Chung Yang Rd, Tucheng, Taipei 236, Taiwan, R.O.C 9 Tel: 886-2-2267-2000, 2267-9936 Fax: 886-2267-6244, 2267-6189, 2267-6306 http://www.everlight.com Copyright © 2010, Everlight All Rights Reserved. Release Date : 26-Apr-2013. Issue No: DSE-0008851 Rev.3 www.everlight.com DATASHEET SMD  REFLECTOR 42-21/BHC-AUW/1T Application Restrictions High reliability applications such as military/aerospace, automotive safety/security systems, and medical equipment may require different product. If you have any concerns, please contact Everlight before using this product in your application. This specification guarantees the quality and performance of the product as an individual component. Do not use this product beyond the specification described in this document. 10 Copyright © 2010, Everlight All Rights Reserved. Release Date : 26-Apr-2013. Issue No: DSE-0008851 Rev.3 www.everlight.com