59-146UWD/TR8

EVERLIGHT ELECTRONICS CO.,LTD. Technical Data Sheet Luminosity white Color LED 59-146 UWD/TR8 Features ․Super luminosity white LED. ․Built in 4 LED chips. ․Wide viewing angle. ․Soldering methods: Reflow soldering. ․High performance. ․Package in 12mm tape on 7〞diameter reel. ․Pb-free. ․The product itself will remain within RoHS compliant version. Descriptions ․The 59-146 SMD Taping is much smaller than lead frame type components, thus enable smaller board size, higher packing density, reduced storage space and finally smaller equipment to be obtained. ․Besides, lightweight makes them ideal for miniature applications. etc. Applications ․Amusement equipment. ․Information boards. ․Flashlight for digital camera of cellular phone. ․Lighting for small size device. Device Selection Guide Chip Lens Color Material Emitted Color InGaN White Yellow diffused Everlight Electronics Co., Ltd. http://www.everlight.com Rev. 2 Page: 1 of 10 Device No.:DES-596-001 Prepared date: 03-Apr-2007 Prepared by: Alex Chen EVERLIGHT ELECTRONICS CO.,LTD. 59-146 UWD/TR8 Package Outline Dimensions Package Mark A CL Pin Mark 2 2 1 3 8 4 7 5 3 1 4 8 5 7 6 6 A Sec A-A (View back) Solder pattern Polarity 2 1 3 8 4 7 5 6 (2) (1) (5) (6) (3) (4) (8) (7) Note: The tolerances unless mentioned is ±0.1mm ,Unit = mm Everlight Electronics Co., Ltd. http://www.everlight.com Rev. 2 Page: 2 of 10 Device No.:DES-596-001 Prepared date: 03-Apr-2007 Prepared by: Alex Chen EVERLIGHT ELECTRONICS CO.,LTD. 59-146 UWD/TR8 Absolute Maximum Ratings (Ta=25℃) Parameter Symbol Rating Unit Reverse Voltage VR 5 V Forward Current IF 30 mA IFP 100 mA Power Dissipation Pd 110 mW Electrostatic Discharge(HBM) ESD 1000 V Electrostatic Discharge (CDM) ESD 500 V Operating Temperature Topr -40 ~ +85 ℃ Storage Temperature Tstg -40 ~ +90 ℃ Soldering Temperature Tsol Peak Forward Current (Duty 1/10 @ 400ms) Reflow Soldering : 260 ℃ for 10 sec. Hand Soldering : 350 ℃ for 3 sec. * The value are base d on the 1-die performance. Electro-Optical Characteristics (Ta=25℃) Parameter Symbol Luminous Intensity*1 Viewing Angle*1 Iv 2θ1/2 Min. Typ. Max. 5.0 8.5 15.0 Unit IF=20mA*2 cd 10.0 25.0 45.0 ----- 50 ----- 2.0 2.4 2.8 2.8 3.2 3.7 3.6 4.3 5.2 ----- ----- 50 Condition deg IFP=100mA*2 (Duty 1/10 @ 400ms) IF=20mA*2 IF=0.1mA*2 Forward Voltage*2 VF Forward Voltage*2 -25℃< T < 30℃ Reverse Current*2 IR V IF=20mA*2 IFP=100mA*2 (Duty 1/10 @ 400ms) μA VR=5V*2 *1 When 4 LED dies are operated simultaneously. *2 For each die. Note: The products are sensitive to static electricity and care must be fully taken when handling products. Everlight Electronics Co., Ltd. http://www.everlight.com Rev. 2 Page: 3 of 10 Device No.:DES-596-001 Prepared date: 03-Apr-2007 Prepared by: Alex Chen EVERLIGHT ELECTRONICS CO.,LTD. 59-146 UWD/TR8 Color Ranks Rank B3 Rank B4 x 0.327 0.323 0.344 0.347 x 0.347 0.344 0.370 0.370 y 0.335 0.345 0.370 0.355 y 0.355 0.370 0.400 0.379 Rank B5 Rank B6 x 0.336 0.327 0.347 0.351 x 0.351 0.347 0.370 0.370 y 0.316 0.335 0.355 0.334 y 0.334 0.355 0.379 0.358 Rank C0 x 0.370 0.370 0.401 0.396 y 0.358 0.400 0.425 0.391 *The C.I.E. 1931 chromaticity diagram ( Tolerance ±0.01). CIE Chromaticity Diagram Everlight Electronics Co., Ltd. http://www.everlight.com Rev. 2 Page: 4 of 10 Device No.:DES-596-001 Prepared date: 03-Apr-2007 Prepared by: Alex Chen EVERLIGHT ELECTRONICS CO.,LTD. 59-146 UWD/TR8 Typical Electro-Optical Characteristics Curves 100% 90% 80% 70% 60% 50% 40% 30% 20% 10% 0% 380 480 580 680 780 Everlight Electronics Co., Ltd. http://www.everlight.com Rev. 2 Page: 5 of 10 Device No.:DES-596-001 Prepared date: 03-Apr-2007 Prepared by: Alex Chen EVERLIGHT ELECTRONICS CO.,LTD. 59-146 UWD/TR8 Label explanation CAT: Luminous Intensity Rank HUE: Chromaticity Coordinates REF: Forward Voltage Rank Reel Dimensions Note: The tolerances unless mentioned is ±0.1mm ,Unit = mm Everlight Electronics Co., Ltd. http://www.everlight.com Rev. 2 Page: 6 of 10 Device No.:DES-596-001 Prepared date: 03-Apr-2007 Prepared by: Alex Chen EVERLIGHT ELECTRONICS CO.,LTD. 59-146 UWD/TR8 Carrier Tape Dimensions: Taping Quantity: 800pcs Note: The tolerances unless mentioned is ±0.1mm ,Unit = mm Moisture Resistant Packaging Label Aluminum moisture-proof bag Desiccant Label Everlight Electronics Co., Ltd. http://www.everlight.com Rev. 2 Page: 7 of 10 Device No.:DES-596-001 Prepared date: 03-Apr-2007 Prepared by: Alex Chen EVERLIGHT ELECTRONICS CO.,LTD. 59-146 UWD/TR8 Reliability Test Items And Conditions The reliability of products shall be satisfied with items listed below. Confidence level：90% LTPD：10% Test Sample Hours/Cycles Size No. Items Test Condition 1 Reflow Soldering Temp. : 260℃±5℃ Min. 5sec. 6 Min. 22 PCS. 0/1 Temperature Cycle H : +100℃ 15min ∫ 5 min L : -40℃ 15min 300 Cycles 22 PCS. 0/1 Thermal Shock H : +100℃ 5min ∫ 10 sec L : -10℃ 5min 300 Cycles 22 PCS. 0/1 Temp. : 100℃ 1000 Hrs. 22 PCS. 0/1 Temp. : -40℃ 1000 Hrs. 22 PCS. 0/1 2 3 4 5 High Temperature Storage Low Temperature Storage Ac/Re 6 DC Operating Life IF = 20 mA 1000 Hrs. 22 PCS. 0/1 7 High Temperature / High Humidity 85℃/ 85%RH 1000 Hrs. 22 PCS. 0/1 Everlight Electronics Co., Ltd. http://www.everlight.com Rev. 2 Page: 8 of 10 Device No.:DES-596-001 Prepared date: 03-Apr-2007 Prepared by: Alex Chen EVERLIGHT ELECTRONICS CO.,LTD. 59-146 UWD/TR8 Precautions For Use 1. Over-current-proof Customer must apply resistors for protection, otherwise slight voltage shift will cause big current change ( Burn out will happen ). 2. Storage 2.1 Do not open moisture proof bag before the products are ready to use. 2.2 Before opening the package: The LEDs should be kept at 30℃ or less and 90%RH or less. 2.3 After opening the package: The LED's floor life is 1 year under 30℃ or less and 60% RH or less. If unused LEDs remain, it should be stored in moisture proof packages. 2.4 If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded the storage time, baking treatment should be performed using the following conditions. Baking treatment : 60±5℃ for 24 hours. 3. Soldering Condition 3.1 Pb-free solder temperature profile 3.2 Reflow soldering should not be done more than two times. 3.3 When soldering, do not put stress on the LEDs during heating. 3.4 After soldering, do not warp the circuit board. Everlight Electronics Co., Ltd. http://www.everlight.com Rev. 2 Page: 9 of 10 Device No.:DES-596-001 Prepared date: 03-Apr-2007 Prepared by: Alex Chen EVERLIGHT ELECTRONICS CO.,LTD. 59-146 UWD/TR8 4.Soldering Iron Each terminal is to go to the tip of soldering iron temperature less than 350℃ for 3 seconds within once in less than the soldering iron capacity 25W. Leave two seconds and more intervals, and do soldering of each terminal. Be careful because the damage of the product is often started at the time of the hand solder. 5.Repairing Repair should not be done after the LEDs have been soldered. When repairing is unavoidable, a double-head soldering iron should be used (as below figure). It should be confirmed beforehand whether the characteristics of the LEDs will or will not be damaged by repairing. EVERLIGHT ELECTRONICS CO., LTD. Office: No 25, Lane 76, Sec 3, Chung Yang Rd, Tucheng, Taipei 236, Taiwan, R.O.C Tel: 886-2-2267-2000, 2267-9936 Fax: 886-2267-6244, 2267-6189, 2267-6306 http://www.everlight.com Everlight Electronics Co., Ltd. http://www.everlight.com Rev. 2 Page: 10 of 10 Device No.:DES-596-001 Prepared date: 03-Apr-2007 Prepared by: Alex Chen