7343-B1C2-APSA-X-MS

Technical Data Sheet 7343/B1C2-APSA/X/MS Features ˙Popular T-1 3/4 package. ˙High efficiency. ˙General purpose leads. ˙Selected minimum intensities. ˙Available on tape and reel. ˙The product itself will remain within RoHS compliant version. ˙UV resistant epoxy Descriptions ˙The series is specially designed for applications requiring higher brightness. ˙The LED lamps are available with different colors, intensities, epoxy colors, etc. Applications ˙Color Graphic Signs ˙Message boards ˙Variable message signs (VMS) ˙Commercial outdoor advertising Device Selection Guide LED Part No. 7343/B1C2-APSB/MS 7343/B1C21-APSB/P/MS Chip Material Emitted Color InGaN Blue Lens Color Water clear Stopper No Yes Everlight Electronics Co., Ltd. http\\:www.everlight.com Rev 1 Page: 1 of 7 Device Number : DLE-734-122 Prepared date: 12-19-2006 Prepared by: Grace Shen Technical Data Sheet 7343/B1C2-APSA/X/MS Package Dimensions Stopper Type No Stopper Type Notes: ˙Other dimensions are in millimeters, tolerance is 0.25mm except being specified. ˙Protruded resin under flange is 1.5mm Max LED. ˙Bare copper alloy is exposed at tie-bar portion after cutting. Everlight Electronics Co., Ltd. http\\:www.everlight.com Rev 1 Page: 2 of 7 Device Number : DLE-734-122 Prepared date: 12-19-2006 Prepared by: Grace Shen Technical Data Sheet 7343/B1C2-APSA/X/MS Absolute Maximum Rating (Ta=25℃ ℃) Parameter Symbol Absolute Maximum Rating Unit Forward Current IF 30 mA Pulse Forward Current (Duty1/10@ 1KHz) IFP 100 mA Operating Temperature Topr -40 ~ +85 ℃ Storage Temperature Tstg -40 ~ +100 ℃ Reverse Voltage VR 5 V Electrostatic Discharge ESD 1K V Soldering Temperature Tsol 260 ±5 ℃ Power Dissipation Pd 110 mW Notes: Soldering time≦5 seconds. Electro-Optical Characteristics (Ta=25℃ ℃) Parameter Symbol Min. Typ. Max. Unit Radiometric Intensity IV 2850 4500 7150 mcd Viewing Angle 2θ1/2 ---- 15 ---- deg Peak Wavelength λp ---- 468 ---- Dominant Wavelength λd 465 470 475 Spectrum Half width Δλ ---- 35 ---- Forward Voltage VF 2.8 3.2 3.6 V IR ---- ---- 50 uA Reverse Current nm Condition IF=20mA VR=5V Everlight Electronics Co., Ltd. http\\:www.everlight.com Rev 1 Page: 3 of 7 Device Number : DLE-734-122 Prepared date: 12-19-2006 Prepared by: Grace Shen Technical Data Sheet 7343/B1C2-APSA/X/MS Rank Combination (IF=20mA) Rank Luminous Intensity P Q R S 2850~3600 3600~4500 4500~5650 5650~7150 *Measurement Uncertainty of Luminous Intensity: ±15% Unit: :mcd Rank 0 1 2 3 Forward Voltage 2.8~3.0 3.0~3.2 3.2~3.4 3.4~3.6 *Measurement Uncertainty of Forward Voltage: ±0.1V Rank 1 Unit:V 2 Dominant Wavelength 465~470 470~475 *Measurement Uncertainty of Dominant Wavelength ±1.0nm Unit:nm Everlight Electronics Co., Ltd. http\\:www.everlight.com Rev 1 Page: 4 of 7 Device Number : DLE-734-122 Prepared date: 12-19-2006 Prepared by: Grace Shen Technical Data Sheet 7343/B1C2-APSA/X/MS Typical Electro-Optical Characteristics Curves Everlight Electronics Co., Ltd. http\\:www.everlight.com Rev 1 Page: 5 of 7 Device Number : DLE-734-122 Prepared date: 12-19-2006 Prepared by: Grace Shen Technical Data Sheet 7343/B1C2-APSA/X/MS Packing Quantity Specification 1.500PCS/1Bag，5Bags/1Box 2.10Boxes/1Carton Label Form Specification CPN: Customer’s Production Number EVERLIGHT CPN: P/N: RoHS 7343/B1C2-APSA/X/MS QTY： CAT: LOT NO： HUE: REF: P/N : Production Number QTY: Packing Quantity CAT: Ranks of Luminous and Forward Voltage HUE: Ranks of Dominant Wavelength REF: Reference LOT No: Lot Number MADE IN TAIWAN: Production Place MADE IN TAIWAN Everlight Electronics Co., Ltd. http\\:www.everlight.com Rev 1 Page: 6 of 7 Device Number : DLE-734-122 Prepared date: 12-19-2006 Prepared by: Grace Shen Technical Data Sheet 7343/B1C2-APSA/X/MS Notes 1. Above specification may be changed without notice. EVERLIGHT will reserve authority on material change for above specification. 2. When using this product, please observe the absolute maximum ratings and the instructions for using outlined in these specification sheets. EVERLIGHT assumes no responsibility for any damage resulting from use of the product which does not comply with the absolute maximum ratings and the instructions included in these specification sheets. 3. These specification sheets include materials protected under copyright of EVERLIGHT corporation. Please don’t reproduce or cause anyone to reproduce them without EVERLIGHT’s consent. 4. Soldering Condition Careful attention should be paid during soldering. When soldering, leave more then 3mm from solder joint to case, and soldering beyond the base of the tie bar is recommended. Avoiding applying any stress to the lead frame while the LEDs are at high temperature particularly when soldering. Recommended soldering conditions: Hand Soldering DIP Soldering Temp. at tip of iron 400℃ Max. (30W Max.) Preheat temp. 100℃ Max. (60 sec Max.) Soldering time 3 sec Max. Bath temp. 265 Max. Distance 3mm Min.(From solder Bath time. 5 sec Max. Distance 3mm Min. joint to case) EVERLIGHT ELECTRONICS CO., LTD. Office: No 25, Lane 76, Sec 3, Chung Yang Rd, Tucheng, Taipei 236, Taiwan, R.O.C Tel: 886-2-2267-2000, 2267-9936 Fax: 886-2267-6244, 2267-6189, 2267-6306 http:\\www.everlight.com Everlight Electronics Co., Ltd. http\\:www.everlight.com Rev 1 Page: 7 of 7 Device Number : DLE-734-122 Prepared date: 12-19-2006 Prepared by: Grace Shen