C3227TDWN3S1-GRBC0112-2T

Top View LEDs C3227TDWN3S1-GRBC0112-2T Features ‧ P-LCC-4 package. ‧ Inner reflector and white package. ‧ Wide viewing angle 120o. ‧ White SMT package. ‧ Soldering methods: IR reflow soldering. ‧ Pb-free. ‧ The product itself will remain within RoHS compliant version. ‧ Compliance with EU REACH. ‧ Compliance Halogen Free .(Br250 µs Single Data in 24bit for RGB： OUT G [7] OUT G [6] OUT G [5] OUT G [4] OUT G [3] OUT G [2] OUT G [1] OUT G [0] OUT R[7 ] OUT R [6 ] OUT R [5 ] OUT R[4 ] OUT R [3 ] OUT R[2 ] OUT R[1 ] OUT R [0 ] OUT B[7 ] OUT B [6 ] OUT B [5 ] OUT B[4 ] OUT B [3 ] OUT B[2 ] OUT B[1 ] OUT B [0 ] 5V Application circuit： Vdd MCU or Controller RC Filter Vss Do Vss Di Vdd Di Do Vdd Vss Do Di Vdd GND Reserved design 4 Reserved design Copyright © 2020, Everlight All Rights Reserved. Release Date :09. Nov. 2020 Issue No: DSE-0023966 Ver.:2 Release Date:11/17/2020 　 Rev. 2 狀態:Approved(正式發行) www.everlight.com DATASHEET Top View LEDs C3227TDWN3S1-GRBC0112-2T Typical Electro-Optical Characteristics Curves Relative Intensity (%) Typical Curve of Spectral Distribution λp (nm) Note: V(λ)=Standard eye response curve; Relative Intensity (%) Diagram Characteristics of Radiation Relative Intensity 5 Copyright © 2020, Everlight All Rights Reserved. Release Date :09. Nov. 2020 Issue No: DSE-0023966 Ver.:2 Release Date:11/17/2020 　 Rev. 2 狀態:Approved(正式發行) www.everlight.com DATASHEET Top View LEDs C3227TDWN3S1-GRBC0112-2T Package Dimension B R G PIN Configuration NO. 1 2 3 4 Symbol DI VDD DO VSS Function description Control data signal input Power supply control circuit Control data signal output Ground Note: Tolerances unless mentioned ±0.1mm. Unit = mm 6 Copyright © 2020, Everlight All Rights Reserved. Release Date :09. Nov. 2020 Issue No: DSE-0023966 Ver.:2 Release Date:11/17/2020 　 Rev. 2 狀態:Approved(正式發行) www.everlight.com DATASHEET Top View LEDs C3227TDWN3S1-GRBC0112-2T Moisture Resistant Packing Materials ‧CPN: Customer’s Product Number ‧P/N: Product Number ‧QTY: Packing Quantity ‧CAT: Luminous Intensity Rank ‧HUE: Dominant Wavelength Rank ‧REF: Forward Voltage Rank ‧LOT No: Lot Number Reel Dimensions 7 Copyright © 2020, Everlight All Rights Reserved. Release Date :09. Nov. 2020 Issue No: DSE-0023966 Ver.:2 Release Date:11/17/2020 　 Rev. 2 狀態:Approved(正式發行) www.everlight.com DATASHEET Top View LEDs C3227TDWN3S1-GRBC0112-2T Carrier Tape Dimensions: Loaded Quantity 2000 pcs Per Reel Note: Tolerances unless mentioned ±0.1mm. Unit = mm Moisture Resistant Packing Process Note: Tolerances unless mentioned ±0.1mm. Unit = mm 8 Copyright © 2020, Everlight All Rights Reserved. Release Date :09. Nov. 2020 Issue No: DSE-0023966 Ver.:2 Release Date:11/17/2020 　 Rev. 2 狀態:Approved(正式發行) www.everlight.com DATASHEET Top View LEDs C3227TDWN3S1-GRBC0112-2T Precautions for Use 1. Over-current-proof 1.1 Customer must apply resistors for protection, otherwise slight voltage shift will cause big current change ( Burn out will happen ). 260°C Max. 10sec. Max. Above255°C 30sec.Max. 3°C/sec.Max. 6°C/sec.Max. Pre-heating Above 217°C 60~150sec. 150~200°C 60~120sec. 2. Storage 2.1 Do not open moisture proof bag before the products are ready to use. 2.2 Before opening the package: The LEDs should be kept at 30℃ or less and 90%RH or less. 2.3 If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded the storage time, baking treatment should be performed using the following conditions. Baking treatment : 60±5℃ for 24 hours. 2.4 It is recommended to solder the LED as soon as possible after unpacking the aluminum envelop, But in case that the LED have to be left unused after unpacking envelop again is requested. The LED should be soldering within 24 hours after opening the package. If baking is required, A baking treatment should be performed as follows: 60℃±5℃ for more than 24 hours. 3. Soldering Condition 3.1 Pb-free solder temperature profile 3.2 Reflow soldering should not be done more than two times. 3.3 When soldering, do not put stress on the LEDs during heating. 3.4 After soldering, do not warp the circuit board. 4. Soldering Iron Each terminal is to go to the tip of soldering iron temperature less than 350℃ for 3 seconds within once in less than the soldering iron capacity 25W. Leave two seconds and more intervals, and do soldering of each terminal. Be careful because the damage of the product is often started at the time of the hand solder. 5. Repairing Repair should not be done after the LEDs have been soldered. When repairing is unavoidable, a double-head soldering iron should be used (as below figure). It should be confirmed beforehand whether the characteristics of the LEDs will or will not be damaged by repairing. 9 Copyright © 2020, Everlight All Rights Reserved. Release Date :09. Nov. 2020 Issue No: DSE-0023966 Ver.:2 Release Date:11/17/2020 　 Rev. 2 狀態:Approved(正式發行) www.everlight.com DATASHEET Top View LEDs C3227TDWN3S1-GRBC0112-2T Application Restrictions High reliability applications such as military/aerospace, automotive safety/security systems, and medical equipment may require different product. If you have any concerns, please contact Everlight before using this product in your application. This specification guarantees the quality and performance of the product as an individual component. Do not use this product beyond the specification described in this document. DISCLAIMER 1. EVERLIGHT reserves the right(s) on the adjustment of product material mix for the specification. 2. The product meets EVERLIGHT published specification for a period of twelve (12) months from date of shipment. 3. The graphs shown in this datasheet are representing typical data only and do not show guaranteed values. 4. When using this product, please observe the absolute maximum ratings and the instructions for using outlined in these specification sheets. EVERLIGHT assumes no responsibility for any damage resulting from the use of the product which does not comply with the absolute maximum ratings and the instructions included in these specification sheets. 5. These specification sheets include materials protected under copyright of EVERLIGHT. Reproduction in any form is prohibited without obtaining EVERLIGHT’s prior consent. 6. This product is not intended to be used for military, aircraft, automotive, medical, life sustaining or life saving applications or any other application which can result in human injury or death. Please contact authorized Everlight sales agent for special application request. 10 Copyright © 2020, Everlight All Rights Reserved. Release Date :09. Nov. 2020 Issue No: DSE-0023966 Ver.:2 Release Date:11/17/2020 　 Rev. 2 狀態:Approved(正式發行) www.everlight.com