D526SURWA/A3/P49

Display  Through-hole ELD-526SURWA/A3/P49 Features • Industrial standard size. • Low power consumption. • Categorized for luminous intensity. •The product itself will remain with RoHS Compliant version. • Compliance with EU REACH. • Compliance with Pb free. Description • The ELD-526SURWA/A3/P49 is a 13.6mm (0.54") digit height seven-segment display. • The display provides excellent reliability in bright ambient light. • The device is made with white segments and gray surface. Applications • Home appliances • Instrument panels • Digital readout displays 1 Copyright © 2010, Everlight All Rights Reserved. Release Date : Mar. 27, 2017 Ver.:3 Release Date:04/13/2017 　 Issue No : DDF-0002282 Rev.3 狀態:Approved(正式發行) www.everlight.com DATASHEET Display  Through-hole ELD-526SURWA/A3/P49 Device Selection Guide Chip Materials Emitted Color Resin Color AlGaInP Brilliant Red White Diffusion Absolute Maximum Ratings (Ta=25℃) Parameter Symbol Rating Unit Reverse Voltage VR 5 V Forward Current IF 25 mA IFP 60 mA Power Dissipation Pd 60 mW Operating Temperature Topr -40 ~ +85 ℃ Storage Temperature Tstg Soldering Temperature Tsol -40 ~ +90 ℃ Wave Soldering : 260 ℃ for 5 sec. Peak Forward Current (Duty 1/10 @1KHz) Hand Soldering : 350 ℃ for 3 sec. Electro-Optical Characteristics (Ta=25℃) Parameter Symbol Min. Typ. Max. Unit Condition Luminous Intensity*1 Iv 7.8 12.5 ----- mcd IF=10mA Peak Wavelength λp ----- 632 ----- nm IF=20mA Dominant Wavelength λd ----- 624 ----- nm IF=20mA Spectrum Radiation Bandwidth Δλ ----- 20 ----- nm IF=20mA Forward Voltage VF IR ----- 2.0 2.4 V IF=20mA ----- ----- 100 μA VR=5V Reverse Current Note: 1. Luminous Intensity is a average value which is measured one 7-segment. 2. Tolerance of Luminous Intensity: ± 10 ％ 3. Tolerance of Forward Voltage: ± 0.1V 2 Copyright © 2010, Everlight All Rights Reserved. Release Date : Mar. 27, 2017 Ver.:3 Release Date:04/13/2017 　 Issue No : DDF-0002282 Rev.3 狀態:Approved(正式發行) www.everlight.com DATASHEET Display  Through-hole ELD-526SURWA/A3/P49 Typical Electro-Optical Characteristics Curves Forward Current vs. Forward Voltage (Ta=25℃) Forward Current (mA) Relative luminous intensity (％) Spectrum Distribution (Ta=25℃) Wavelength λp (nm) Forward Voltage (V) Forward Current (mA) Forward Current Derating Curve Ambient Temperature (°C ) 3 Copyright © 2010, Everlight All Rights Reserved. Release Date : Mar. 27, 2017 Ver.:3 Release Date:04/13/2017 　 Issue No : DDF-0002282 Rev.3 狀態:Approved(正式發行) www.everlight.com DATASHEET Display  Through-hole ELD-526SURWA/A3/P49 Package Dimension & Internal Circuit Diagram Note: Tolerances unless mentioned ±0.25mm. Unit = mm 4 Copyright © 2010, Everlight All Rights Reserved. Release Date : Mar. 27, 2017 Ver.:3 Release Date:04/13/2017 　 Issue No : DDF-0002282 Rev.3 狀態:Approved(正式發行) www.everlight.com DATASHEET Display  Through-hole ELD-526SURWA/A3/P49 Packing Materials Label Explanation ‧CPN: Customer’s Product Number ‧P/N: Product Number ‧QTY: Packing Quantity ‧CAT: Luminous Intensity Rank ‧HUE: Reference ‧REF: Reference ‧LOT No: Lot Number ‧REFERENCE: Volume Label code D526SURWA/A3/P49 Packing Process 20 PCS/Tube 5 36 Tubes/Box Copyright © 2010, Everlight All Rights Reserved. Release Date : Mar. 27, 2017 Ver.:3 Release Date:04/13/2017 　 4 Boxes/Carton Issue No : DDF-0002282 Rev.3 狀態:Approved(正式發行) www.everlight.com DATASHEET Display  Through-hole ELD-526SURWA/A3/P49 Precautions for Use 1. Soldering Condition 1.1 Maximum Body Case Temperature Profile for evaluation of DIP Soldering Profile Note: Preheat Temperature 100 °C Time 60 seconds max. Other Bath Temperature 260C Bath Time 5 seconds max. DIP Soldering 1 time All parameters are maximum body case temperature values and cannot be considered as a soldering profile. The body case temperature was measured by soldering a thermal couple to the soldering point of LEDs. 2. Soldering Iron Each terminal is to go to the tip of soldering iron temperature less than 350℃ for 3 seconds within once in less than the soldering iron capacity 25W. Leave two seconds and more intervals, and do soldering of each terminal. Be careful because the damage of the product is often started at the time of the hand solder. 6 Copyright © 2010, Everlight All Rights Reserved. Release Date : Mar. 27, 2017 Ver.:3 Release Date:04/13/2017 　 Issue No : DDF-0002282 Rev.3 狀態:Approved(正式發行) www.everlight.com DATASHEET Display  Through-hole ELD-526SURWA/A3/P49 DISCLAIMER 1. EVERLIGHT reserves the right(s) on the adjustment of product material mix for the specification. 2. The Product meet EVERLIGHT published specification for a period of twelve(12 ) months from date of shipment. 3. The graphs shown in this datasheet are representing typical data only and do not show guaranteed values. 4. When using this product, please observe the absolute maximum ratings and the instructions for using outlined in these specification sheets. EVERLIGHT assumes no responsibility for any damage resulting from the use of the product which does not comply with the absolute maximum ratings and the instructions included in these specification sheets. 5. These specification sheets include materials protected under copyright of EVERLIGHT. Reproduction in any form is prohibited without obtaining EVERLIGHT’s prior consent. 6. This product is not intended to be used for military, aircraft, automotive, medical, life sustaining or life saving applications or any other application which can result in human injury or death. Please contact authorized Everlight sales agent for special application request. 7. ESD (Electrostatic Discharge)  The products are sensitive to static electricity or surge voltage. ESD can damage a die and its reliability. When handling the products, the following measures against electrostatic discharge are strongly recommended: Eliminating the charge Grounded wrist strap, ESD footwear, clothes, and floors Grounded workstation equipment and tools ESD table/shelf mat made of conductive materials  Proper grounding is required for all devices, equipment, and machinery used in product assembly. Surge protection should be considered when designing of commercial products.  If tools or equipment contain insulating materials such as glass or plastic, the following measures against electrostatic discharge are strongly recommended: Dissipating static charge with conductive materials Preventing charge generation with moisture Neutralizing the charge with ionizers 8. The LEDs should be operated with forward bias. The driving circuit must be designed so that the LEDs are not subjected to forward or reverse voltage while it is off. If reverse voltage is continuously applied to the LEDs, it may cause migration resulting in LED damage. 7 Copyright © 2010, Everlight All Rights Reserved. Release Date : Mar. 27, 2017 Ver.:3 Release Date:04/13/2017 　 Issue No : DDF-0002282 Rev.3 狀態:Approved(正式發行) www.everlight.com