EAAY03QLA4-RBA0

LAMP EAAY03QLA4-RBA0 Features •Low power consumption •High efficiency and low cost •Good control and free combinations on the colors of LED lamps •Good lock and easy to assembly. •Stackable and easy to assembly Stackable vertically and easy to assembly •Versatile mounting on P.C board or panel •Stackable horizontally and easy to assembly •Pb free •The product itself will remain within RoHS compliant version Description •ARRAY=Plastic Holder+ Combinations of Lamps. •The array will easily mount the applicable lamps on any panel up to. Applications •Used as indicators of indicating the Degree, Functions, Positions etc, in electronic instruments 1 Copyright © 2010, Everlight Americas All Rights Reserved. Release Date : June.26.2013. Issue No: 1 Rev.1 www.everlightamericas.com DATASHEET LAMP EAAY03QLA4-RBA0 Device Selection Guide Chip PART NO. Emitted Color Materials AIGaInP Brilliant Red InGaN Blue Resin Color 264-2SURSUBW/S530-A3 WhIte Diffiused Absolute Maximum Ratings (Ta=25℃ ℃) Parameter Symbol Rating Unit SUR/S530 25 SUB/S530 25 SUR/S530 60 SUB/S530 100 Continuous Forward Current IF Peak Forward Current (Duty 1/10 @ 1KHZ) IFP Reverse Voltage VR Power Dissipation Pd Operating Temperature Topr -40 ~ +85 Storage Temperature Tstg -40 ~ +100 Soldering Temperature Tsol 5 mA V SUR/S530 60 SUB/S530 90 260 mA mW ℃ ℃ ℃ for 5 sec. Electro-Optical Characteristics (Ta=25℃ ℃) Parameter Forward Voltage Reverse Current Luminous Intensity Viewing Angle Peak Wavelength Dominant Wavelength Spectrum Radiation Bandwidth 2 Symbol Min Typ Max SUR/S530 1.7 2.0 2.4 SUB/S530 2.7 3.3 3.7 SUR/S530 ----- ----- 10 SUB/S530 ----- ----- 10 SUR/S530 63 125 ----- SUB/S530 40 80 ----- SUR/S530 ----- 100 ---- SUB/S530 ----- 100 ----- SUR/S530 ----- 632 ---- SUB/S530 ----- 468 ----- SUR/S530 ----- 624 ----- SUB/S530 ----- 470 ----- SUR/S530 ----- 20 ----- SUB/S530 ----- 35 ----- VF IR IV 2θ1/2 λ λ p d △λ Copyright © 2010, Everlight Americas All Rights Reserved. Release Date : June.26.2013. Issue No: 1 Rev.1 Unit Condition V IF=20mA nm VR=5V mcd IF=20mA deg IF=20mA nm IF=20mA nm IF=20mA nm IF=20mA www.everlightamericas.com DATASHEET LAMP EAAY03QLA4-RBA0 Typical Electro-Optical Characteristics Curves SUR ℃) ℃) Directivity (Ta=25 Radiation Angle Relative Intensity (a.u.) Relative Intensity vs. Wavelength (Ta=25 Wavelength (nm) ℃) Forward Current vs. Forward Voltage (Ta=25 Relative Intensity (a.u.) ℃) Relative Intensity vs. Forward Current (Ta=25 Forward Current (mA) Relative Intensity(a.u.) 1.5 1.0 0.5 0.0 0 Forward Voltage (V) 20 25 40 Forward Current (mA) Relative Intensity(a.u.) 15 Forward Current vs. Ambient Temp. 2.0 1.5 1.0 0.5 30 35 40 45 50 55 60 Ambient Temperature Ta( 3 10 Forward Current (mA) Relative Intensity vs. Ambient Temp. 0.0 25 5 65 ℃) 70 30 20 10 0 0 20 40 60 80 Ambient Temperature Ta( Copyright © 2010, Everlight Americas All Rights Reserved. Release Date : June.26.2013. Issue No: 1 Rev.1 ℃) 100 www.everlightamericas.com DATASHEET LAMP EAAY03QLA4-RBA0 SUB ℃) ℃) Directivity (Ta=25 Radiation Angle Relative Intensity (a.u.) Relative Intensity vs. Wavelength (Ta=25 Wavelength (nm) ℃) Forward Current vs. Forward Voltage (Ta=25 Relative Intensity (a.u.) ℃) Relative Intensity vs. Forward Current (Ta=25 Forward Current (mA) Relative Intensity(a.u.) 1.5 1.0 0.5 0.0 0 Forward Voltage (V) 20 25 40 Forward Current (mA) Relative Intensity(a.u.) 15 Forward Current vs. Ambient Temp. 2.0 1.5 1.0 0.5 30 35 40 45 50 55 60 Ambient Temperature Ta( 4 10 Forward Current (mA) Relative Intensity vs. Ambient Temp. 0.0 25 5 65 ℃) 70 30 20 10 0 0 20 40 60 80 Ambient Temperature Ta( Copyright © 2010, Everlight Americas All Rights Reserved. Release Date : June.26.2013. Issue No: 1 Rev.1 ℃) 100 www.everlightamericas.com DATASHEET LAMP EAAY03QLA4-RBA0 Package Dimension Note: Note: 1. All dimensions are in millimeters, tolerance is 0.25mm except being specified 2. Lead spacing is measured where the lead emerge from the package. 5 Copyright © 2010, Everlight Americas All Rights Reserved. Release Date : June.26.2013. Issue No: 1 Rev.1 www.everlightamericas.com DATASHEET LAMP EAAY03QLA4-RBA0 Moisture Resistant Packing Materials Label Explanation ‧CPN: Customer’s Product Number ‧P/N: Product Number ‧QTY: Packing Quantity ‧CAT: Ranks of Luminous Intensity ‧HUE: Ranks of Dominant Wavelength ‧REF: Ranks of Forward Voltage ‧LOT No: Lot Number Packing Specification ■Anti-electrostatic bag ■ 6 ■ Inner Carton ■ Outside Carton Packing Quantity 1. 140 PCS/1 Plate, 3 Plates/1 Inner Carton 2. 10 Inner Cartons/1 Outside Carton Copyright © 2010, Everlight Americas All Rights Reserved. Release Date : June.26.2013. Issue No: 1 Rev.1 www.everlightamericas.com DATASHEET LAMP EAAY03QLA4-RBA0 Notes 1. Lead Forming
During lead formation, the leads should be bent at a point at least 3mm from the base of the epoxy bulb.
Lead forming should be done before soldering.
Avoid stressing the LED package during leads forming. The stress to the base may damage the LED’s characteristics or it may break the LEDs.
Cut the LED lead frames at room temperature. Cutting the lead frames at high temperatures may cause failure of the LEDs.
When mounting the LEDs onto a PCB, the PCB holes must be aligned exactly with the lead position of the LED. If the LEDs are mounted with stress at the leads, it causes deterioration of the epoxy resin and this will degrade the LEDs. 2. Storage
The LEDs should be stored at 30°C or less and 70%RH or less after being shipped from Everlight Americas and the storage life limits are 3 months. If the LEDs are stored for 3 months or more, they can be stored for a year in a sealed container with a nitrogen atmosphere and moisture absorbent material.
Please avoid rapid transitions in ambient temperature, especially, in high humidity environments where condensation can occur. 3. Soldering
Careful attention should be paid during soldering. When soldering, leave more then 3mm from solder joint to epoxy bulb, and soldering beyond the base of the tie bar is recommended.
Recommended soldering conditions:
Hand Soldering 300 Max. (30W Max.) Temp. at tip of iron Soldering time 3 sec Max. Distance 3mm Min.(From solder joint to epoxy bulb) Recommended soldering profile ℃ Preheat temp. Bath temp. & time Distance DIP Soldering 100 Max. (60 sec Max.) 260 Max., 5 sec Max 3mm Min. (From solder joint to epoxy bulb) ℃ laminar wave Fluxing Preheat
Avoiding applying any stress to the lead frame while the LEDs are at high temperature particularly when soldering.
Dip and hand soldering should not be done more than one time
After soldering the LEDs, the epoxy bulb should be protected from mechanical shock or vibration until the LEDs return to room temperature. 7 Copyright © 2010, Everlight Americas All Rights Reserved. Release Date : June.26.2013. Issue No: 1 Rev.1 www.everlightamericas.com DATASHEET LAMP EAAY03QLA4-RBA0
A rapid-rate process is not recommended for cooling the LEDs down from the peak temperature.
Although the recommended soldering conditions are specified in the above table, dip or handsoldering at the lowest possible temperature is desirable for the LEDs.
Wave soldering parameter must be set and maintain according to recommended temperature and dwell time in the solder wave. . 4. Cleaning
When necessary, cleaning should occur only with isopropyl alcohol at room temperature for a duration of no more than one minute. Dry at room temperature before use.
Do not clean the LEDs by the ultrasonic. When it is absolutely necessary, the influence of ultrasonic cleaning on the LEDs depends on factors such as ultrasonic power and the assembled condition. Ultrasonic cleaning shall be pre-qualified to ensure this will not cause damage to the LED 5. Heat Management
Heat management of LEDs must be taken into consideration during the design stage of LED application. The current should be de-rated appropriately by referring to the de-rating curve found in each product specification.
The temperature surrounding the LED in the application should be controlled. Please refer to the data sheet de-rating curve. 6. ESD (Electrostatic Discharge)
The products are sensitive to static electricity or surge voltage. ESD can damage a die and its reliability. When handling the products, the following measures against electrostatic discharge are strongly recommended: Eliminating the charge Grounded wrist strap, ESD footwear, clothes, and floors Grounded workstation equipment and tools ESD table/shelf mat made of conductive materials
Proper grounding is required for all devices, equipment, and machinery used in product assembly. Surge protection should be considered when designing of commercial products.
If tools or equipment contain insulating materials such as glass or plastic, the following measures against electrostatic discharge are strongly recommended: Dissipating static charge with conductive materials Preventing charge generation with moisture Neutralizing the charge with ionizers. 7. Directions for use
The LEDs should be operated with forward bias. The driving circuit must be designed so that the LEDs are not subjected to forward or reverse voltage while it is off. If reverse voltage is continuously applied to the LEDs, it may cause migration resulting in LED damage. 8. Other
Above specification may be changed without notice. Everlight Americas will reserve authority on material change for above specification.
8 When using this product, please observe the absolute maximum ratings and the instructions for using outlined in these Copyright © 2010, Everlight Americas All Rights Reserved. Release Date : June.26.2013. Issue No: 1 Rev.1 www.everlightamericas.com DATASHEET LAMP EAAY03QLA4-RBA0 specification sheets. Everlight Americas assumes no responsibility for any damage resulting from use of the product which does not comply with the absolute maximum ratings and the instructions included in these specification sheets.
9 These specification sheets include materials protected under copyright of Everlight Americas corporation. Please don’t reproduce or cause anyone to reproduce them without Everlight Americas's consent. Copyright © 2010, Everlight Americas All Rights Reserved. Release Date : June.26.2013. Issue No: 1 Rev.1 www.everlightamericas.com