EAIST3015A1

1206 Package Infrared Chip LED With Inner Lens EAIST3015A1 Features ․Small double-end package ․High reliability ․Low forward voltage ․Good spectral matching to Si photodetector ․Package in 8mm tape on 7” diameter reel ․Pb free ․The product itself will remain within RoHS compliant version. Descriptions EAIST3015A1 is an infrared emitting diode in miniature SMD package which is molded in a water clear plastic with flat top view lens. The device is spectrally matched with silicon photodiode and phototransistor. Applications ․PCB mounted infrared sensor ․Infrared emitting for miniature light barrier ․Floppy disk drive ․Optoelectronic switch ․Smoke detector Device Selection Guide 1 Part No. Chip Material Resin Color EAIST3015A1 GaAlAs Water Clear Copyright © 2010, Everlight Americas Inc. All Rights Reserved. Release Date : 5/28/2013. Issue No: 1 Rev:1 www.everlightamericas.com Data Sheet 1206 Package Infrared Chip LED With Inner Lens EAIST3015A1 Package Dimensions Notes: 1.All dimensions are in millimeters 2.Tolerances unless dimensions ±0.1mm 2 Copyright © 2010, Everlight Americas Inc. All Rights Reserved. Release Date : 5/28/2013. Issue No: 1 Rev:1 www.everlightamericas.com Data Sheet 1206 Package Infrared Chip LED With Inner Lens EAIST3015A1 Absolute Maximum Ratings (Ta=25℃) Parameter Symbol Rating Reverse Voltage VR 5 Units V Continuous Forward Current IF 65 mA Power Dissipation at(or below) 25℃Free Air Temperature Pd 130 mW Operating Temperature Topr -25 ~ +85 ℃ Storage Temperature Tstg -40 ~ +100 ℃ Reflow Soldering : 260 ℃ for 10 sec. Soldering Temperature Tsol Hand Soldering : 350 ℃ for 3 sec. Electro-Optical Characteristics (Ta=25℃) 3 Parameter Symbol Min. Typ. Max. Unit Radiant Intensity Ie 1.25 2.25 ---- mW/sr Viewing Angle 2θ1/2 ---- 100 ---- deg Peak Wavelength λp ---- 940 ---- nm Spectrum Radiation Bandwidth △λ ---- 45 ---- nm Forward Voltage VF ---- 1.2 1.5 V Reverse Current IR ---- ---- 10 μA Copyright © 2010, Everlight Americas Inc. All Rights Reserved. Release Date : 5/28/2013. Issue No: 1 Rev:1 Condition IF=20mA VR=5V www.everlightamericas.com Data Sheet 1206 Package Infrared Chip LED With Inner Lens EAIST3015A1 Typical Electro-Optical Characteristics Curves Fig.1 Forward Current vs. Ambient Temperature Fig.2 Spectral Distribution 140 100 IF=20mA Ta=25° C 120 80 100 80 60 60 40 40 20 20 0 -25 Fig.3 0 20 40 60 80 0 100 Peak Emission Wavelength Fig.4 Ambient Temperature Forward Current vs. Forward Voltage 4 10 980 960 3 10 940 2 10 920 900 -25 4 0 25 50 75 100 1 10 0 Copyright © 2010, Everlight Americas Inc. All Rights Reserved. Release Date : 5/28/2013. Issue No: 1 1 2 Rev:1 3 4 www.everlightamericas.com Data Sheet 1206 Package Infrared Chip LED With Inner Lens EAIST3015A1 Typical Electro-Optical Characteristics Curves Fig.5 Relative Intensity vs. Fig.6 Relative Radiant Intensity vs. Forward Current Angular Displacement -20 Ie-Radiant Intensity(mW/sr) 100 -10 0 10 20 30 10 1 0 10 0 10 1 2 10 10 3 10 4 1.0 40 0.9 50 0.8 0.7 60 70 80 0.6 0.4 0.2 0 0.2 0.4 0.6 IF-Forward Current (mA) 5 Copyright © 2010, Everlight Americas Inc. All Rights Reserved. Release Date : 5/28/2013. Issue No: 1 Rev:1 www.everlightamericas.com Data Sheet 1206 Package Infrared Chip LED With Inner Lens EAIST3015A1 Precautions For Use 1. Over-current-proof Customer must apply resistors for protection,otherwise slight voltage shift will cause big current change (Burn out will happen). 2. Storage 2.1 Do not open moisture proof bag before the products are ready to use. 2.2 Before opening the package: The LEDs should be kept at 30℃ or less and 90%RH or less. 2.3 The LEDs should be used within a year. 2.4 After opening the package, the LEDs should be kept at 30℃ or less and 60%RH or less. 2.5 The LEDs should be used within 168 hours (7 days) after opening the package. 2.6 If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded the storage time, baking treatment should be performed using the following conditions. Baking treatment : 60±5℃ for 48 hours. 3. Soldering Condition 3.1 Pb-free solder temperature profile 3.2 Reflow soldering should not be done more than two times. 3.3 When soldering, do not put stress on the LEDs during heating. 3.4 After soldering, do not warp the circuit board. 6 Copyright © 2010, Everlight Americas Inc. All Rights Reserved. Release Date : 5/28/2013. Issue No: 1 Rev:1 www.everlightamericas.com Data Sheet 1206 Package Infrared Chip LED With Inner Lens EAIST3015A1 4. Soldering Iron Each terminal is to go to the tip of soldering iron temperature less than 350℃ for 3 seconds within once in less than the soldering iron capacity 25W. Leave two seconds and more intervals, and do soldering of each terminal. Be careful because the damage of the product is often started at the time of the hand solder. 5. Repairing Repair should not be done after the LEDs have been soldered. When repairing is unavoidable, a double-head soldering iron should be used (as below figure). It should be confirmed beforehand whether the characteristics of the LEDs will or will not be damaged by repairing. 7 Copyright © 2010, Everlight Americas Inc. All Rights Reserved. Release Date : 5/28/2013. Issue No: 1 Rev:1 www.everlightamericas.com Data Sheet 1206 Package Infrared Chip LED With Inner Lens EAIST3015A1 Package Dimensions Note: The tolerances unless mentioned are ±0.1, unit=mm. Carrier Taping Dimensions: Loaded Quantity Per Reel 2000PCS/Reel Note: The tolerances unless mentioned is ±0.1mm, Unit = mm 8 Copyright © 2010, Everlight Americas Inc. All Rights Reserved. Release Date : 5/28/2013. Issue No: 1 Rev:1 www.everlightamericas.com Data Sheet 1206 Package Infrared Chip LED With Inner Lens EAIST3015A1 Label Form Specification CPN: Customer’s Production Number P/N : Production Number QTY: Packing Quantity CAT: Ranks HUE: Peak Wavelength REF: Reference LOT No: Lot Number Notes 1. Above specification may be changed without notice. Everlight Americas will reserve authority on material change for above specification. 2. When using this product, please observe the absolute maximum ratings and the instructions for using outlined in these specification sheets. Everlight Americas assumes no responsibility for any damage resulting from use of the product which does not comply with the absolute maximum ratings and the instructions included in these specification sheets. 3. These specification sheets include materials protected under copyright of Everlight Americas corporation. Please don’t reproduce or cause anyone to reproduce them without Everlight Americas’s consent. 9 Copyright © 2010, Everlight Americas Inc. All Rights Reserved. Release Date : 5/28/2013. Issue No: 1 Rev:1 www.everlightamericas.com