EAPDST3227A0

Technical Data Sheet Silicon PIN Photodiode EAPDST3227A0 Features ․Fast response time ․High photo sensitivity ․Small junction capacitance ․Pb free ․The product itself will remain within RoHS compliant version. Description ․EAPDST3227A0 is a high speed and high sensitive. PIN photodiode in miniature flat top view lens SMD package and it is molded in a black plastic. The device is Spectrally matched to visible and infrared emitting diode. Applications ․High speed photo detector ․Copier ․Game machine Device Selection Guide 1 Device No. Chip Material Lens Color EAPDST3227A0 Silicon Black Copyright © 2010, Everlight Americas Inc. All Rights Reserved. Release Date : May.05.2014. Issue No: XXXXXXXXXX Rev.0.1 www.everlightamericas.com DATASHEET EAPDST3227A0 Package Dimensions 1 2 4 3 2 3 1 4 2 3 1 4 Notes: 1.All dimensions are in millimeters 2.Tolerances unless dimensions ±0.1mm Absolute Maximum Ratings (Ta=25℃) Parameter Reverse Voltage Operating Temperature Storage Temperature Soldering Temperature *1 Power Dissipation at(or below) ESD HMB Level Symbol VR Topr Tstg Tsol Pc HMB Rating 32 -40 ~ +85 -40 ~ +100 260 150 Min.2000 Unit V ℃ ℃ ℃ mW V Notes: *1:Soldering time≦5 seconds. 2 Copyright © 2010, Everlight Americas Inc. All Rights Reserved. Release Date : May.05.2014. Issue No: XXXXXXXXXX Rev.0.1 www.everlightamericas.com DATASHEET EAPDST3227A0 Electro-Optical Characteristics (Ta=25℃) Parameter Symbol Min. Typ. Max. Unit Condition Rang Of Spectral Bandwidth λ 730 --- 1100 nm 10% of λ Wavelength Of Peak Sensitivity λ P --- 940 --- nm Open-Circuit Voltage VOC --- 0.41 --- V Short-Circuit Current ISC 4.0 6.5 --- μ A Reverse Light Current IL 4.2 6.5 --- μ A Dark Reverse Current ID --- --- 10 nA BVR 32 170 --- V tr --- 10 --- Reverse Breakdown Voltage Rise Time P --Ee=5mW /cm2 λ P=940nm Ee=1mW /cm2 λ P=875nm Ee=1mW /cm2 λ P=875nm VR=5V Ee=0mW /cm2 VR=10V Ee=0mW /cm2 IR=100μ A VCE=10V nS Fall Time View Angle 3 tf --- 10 --- 2θ 1/2 --- 130 --- Copyright © 2010, Everlight Americas Inc. All Rights Reserved. Release Date : May.05.2014. Issue No: XXXXXXXXXX Rev.0.1 VR=5V RL=1000Ω deg VR=5V www.everlightamericas.com DATASHEET EAPDST3227A0 Typical Electrical/Optical/Characteristics Curves for IR Power Dissipation vs. Ambient Temperature Spectral Sensitivity 200 150 100 50 0 -25 0 25 50 75 85 100 Reverse Light Current vs. Ee Dark Current vs. Ambient Temperature 1000 20 15 100 10 10 5 VR=5V VR=10V 0 1 20 40 60 80 100 0.5 1.0 1.5 3.0 2 4 Copyright © 2010, Everlight Americas Inc. All Rights Reserved. Release Date : May.05.2014. Issue No: XXXXXXXXXX Rev.0.1 www.everlightamericas.com DATASHEET EAPDST3227A0 Terminal Capacitance vs. Reverse Voltage t 10 f=1MHZ VR=5V Response Time vs. Load Resistance 10 1 Ta=25°C 2 8 VR=10V 0 10 6 -1 10 -2 4 10 2 10 -3 0.1 1 10 100 10 1 2 10 3 10 10 4 5 10 Relative Light Current vs. Angular Displacement 5 Copyright © 2010, Everlight Americas Inc. All Rights Reserved. Release Date : May.05.2014. Issue No: XXXXXXXXXX Rev.0.1 www.everlightamericas.com DATASHEET EAPDST3227A0  Precautions For Use 1. Over-current-proof Customer must apply resistors for protection , otherwise slight voltage shift will cause big current change ( Burn out will happen ). 2. Storage 2.1 Do not open moisture proof bag before the products are ready to use. 2.2 Before opening the package, the LEDs should be kept at 30℃ or less and 90%RH or less. 2.3 The LEDs should be used within a year. 2.4 After opening the package, the LEDs should be kept at 30℃ or less and 70%RH or less. 2.5 The LEDs should be used within 168 hours (7 days) after opening the package 2.6 If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded the storage time, baking treatment should be performed using the following conditions. Baking treatment : 60±5℃ for 24 hours. 3. Soldering Condition 3.1 Pb-free solder temperature profile 3.2 Reflow soldering should not be done more than two times. 3.3 When soldering, do not put stress on the LEDs during heating. 3.4 After soldering, do not warp the circuit board. 6 Copyright © 2010, Everlight Americas Inc. All Rights Reserved. Release Date : May.05.2014. Issue No: XXXXXXXXXX Rev.0.1 www.everlightamericas.com DATASHEET EAPDST3227A0 4. Soldering Iron Each terminal is to go to the tip of soldering iron temperature less than 350℃ for 3 seconds within once in less than the soldering iron capacity 25W. Leave two seconds and more intervals, and do soldering of each terminal. Be careful because the damage of the product is often started at the time of the hand solder. 5. Repairing Repair should not be done after the LEDs have been soldered. When repairing is unavoidable, a double-head soldering iron should be used (as below figure). It should be confirmed beforehand whether the characteristics of the LEDs will or will not be damaged by repairing. 7 Copyright © 2010, Everlight Americas Inc. All Rights Reserved. Release Date : May.05.2014. Issue No: XXXXXXXXXX Rev.0.1 www.everlightamericas.com DATASHEET EAPDST3227A0 Package Dimensions Note: The tolerances unless mentioned is ±0.1mm ,Unit = mm 2. Carrier Tape Dimensions:(Quantity: 3000pcs/reel) 2.0±0.05 4.0 0.23 3.35 8.0 2 3.5±0.05 1.75 1.55±0.05 1 4.0 2.95 1 Anode 2 Cathode Note: The tolerances unless mentioned is ±0.1mm ,Unit = mm 8 Copyright © 2010, Everlight Americas Inc. All Rights Reserved. Release Date : May.05.2014. Issue No: XXXXXXXXXX Rev.0.1 1.65 www.everlightamericas.com DATASHEET EAPDST3227A0 Packing Procedure Label Aluminum moistue-proof bag Desiccant Label Label Form Specification CPN: Customer’s Production Number P/N : Production Number QTY: Packing Quantity CAT: Ranks HUE: Peak Wavelength REF: Reference LOT No: Lot Number MADE IN TAIWAN: Production Place Notes 1. Above specification may be changed without notice. EVERLIGHT will reserve authority on material change for above specification. 2. When using this product, please observe the absolute maximum ratings and the instructions for using outlined in these specification sheets. EVERLIGHT assumes no responsibility for any damage resulting from use of the product which does not comply with the absolute maximum ratings and the instructions included in these specification sheets. 3. These specification sheets include materials protected under copyright of EVERLIGHT corporation. Please don’t reproduce or cause anyone to reproduce them without without Everlight Americas’s consent. 9 Copyright © 2010, Everlight Americas Inc. All Rights Reserved. Release Date : May.05.2014. Issue No: XXXXXXXXXX Rev.0.1 www.everlightamericas.com