EAPL4040RA0

SMD  REFLECTOR EAPL4040RA0 PRELIMINARY Features ˙Fluorescence Type ․High Luminous Intensity ․High Efficiency ․Pb-free. ․The product itself will remain with RoHS compliant version . Applications ․OA Equipment ․Backlighting of Full Color LCD ․Replacement of Conventional Light ․Bulbs and Fluorescent Lamps 1 Copyright © 2010, Everlight Americas All Rights Reserved. Release Date : Apr.30.2014. Issue No: XXXXXXX www.everlightamericas.com DATASHEET SMD  REFLECTOR EAPL4040RA0 Device Selection Guide Chip Materials AlGaInP Emitted Color Resin Color Brilliant Red Water Clear Absolute Maximum Ratings (Ta=25℃) 2 Parameter Symbol Rating Unit Reverse Voltage VR 5 V Forward Current IF 25 mA Peak Forward Current (Duty 1/10 @1KHz) IFP 60 mA Power Dissipation Pd 60 mW Electrostatic Discharge(HBM) ESD 2000 V Operating Temperature Topr -40 ~ +85 ℃ Storage Temperature Tstg -40 ~+100 ℃ Soldering Temperature Tsol Reflow Soldering : 260 ℃ for 10 sec. Hand Soldering : 350 ℃ for 3 sec. Copyright © 2010, Everlight Americas All Rights Reserved. Release Date : Apr.30.2014. Issue No: XXXXXXX www.everlightamericas.com DATASHEET SMD  REFLECTOR EAPL4040RA0 Electro-Optical Characteristics (Ta=25℃) Parameter Symbol Min. Typ. Max. Unit Condition Luminous Intensity Iv 45 ----- 112 mcd IF=20mA Viewing Angle 2θ1/2 ----- 120 ----- deg IF=20mA Peak Wavelength λp ----- 632 ----- nm IF=20mA Dominant Wavelength λd 617.5 ----- 633.5 nm IF=20mA Spectrum Radiation Bandwidth △λ ----- 20 ----- nm IF=20mA Forward Voltage VF 1.75 ----- 2.35 V IF=20mA Reverse Current IR ----- ----- 10 μA VR=5V Note: 1. Tolerance of Luminous Intensity: ±11% 2. Tolerance of Dominant Wavelength: ±1nm 3. Tolerance of Forward Voltage: ±0.1V Bin Range of Luminous Intensity Bin Min Max P1 45 57 P2 57 72 Q1 72 90 Q2 90 112 Unit Condition mcd IF=20mA Note: Tolerance of Luminous Intensity: ±11% 3 Copyright © 2010, Everlight Americas All Rights Reserved. Release Date : Apr.30.2014. Issue No: XXXXXXX www.everlightamericas.com DATASHEET SMD  REFLECTOR EAPL4040RA0 Bin Range of Dominant Wavelength Group A Bin Code Min. Max. E4 617.5 621.5 E5 621.5 625.5 E6 625.5 629.5 E7 629.5 633.5 Bin Min Max 0 1.75 1.95 1 1.95 2.15 2 2.15 2.35 Unit Condition nm IF=20mA Unit Condition V IF=20mA Note: Tolerance of Dominant Wavelength: ±1nm Bin Range of Forward Voltage Group B Note: Tolerance of Forward Voltage ±0.1V 4 Copyright © 2010, Everlight Americas All Rights Reserved. Release Date : Apr.30.2014. Issue No: XXXXXXX www.everlightamericas.com DATASHEET SMD  REFLECTOR EAPL4040RA0 Typical Electro-Optical Characteristics Curves Forward Current vs. Forward Voltage Spectrum Distribution Ta=25°C 50 Forward Current I F (mA) Relative luminous intensity (%) 100 75 50 25 0 550 30 20 10 1.2 750 100 10 0 2.0 2.8 3.0 20 40 60 80 100 1000 f=1KHz Duty=1/10 100 10 1 0 10 Ambient Temperature T a (°C) 2 1 3 10 10 Forward Current I F (mA) Radiation Diagram Forward Current Derating Curve 0° 40 Forward Current I F (mA) 2.4 Relative Luminous Intensity vs. Forward Current Ta=25°C Relative luminous intensity (%) 1000 1 -60 -40 -20 1.6 Forward Voltage VF (V) Relative Luminous Intensity vs. Ambient Temperature Relative luminous intensity (%) 40 0 600 650 700 Wavelength λ (nm) Ta=25°C 10° 10 Ta=25°C 20° 30° 30 40° 1.0 20 0.9 50° 0.8 60° 10 70° 0.7 0 0 20 40 60 80 100 80° 90° 0.5 0.3 0.1 0.2 0.4 0.6 Ambient Temperature T a (°C) 5 Copyright © 2010, Everlight Americas All Rights Reserved. Release Date : Apr.30.2014. Issue No: XXXXXXX www.everlightamericas.com DATASHEET SMD  REFLECTOR EAPL4040RA0 Package Dimension Note: Tolerances unless mentioned ±0.1mm. Unit = mm 6 Copyright © 2010, Everlight Americas All Rights Reserved. Release Date : Apr.30.2014. Issue No: XXXXXXX www.everlightamericas.com DATASHEET SMD  REFLECTOR EAPL4040RA0 Moisture Resistant Packing Materials Label Explanation CAT: Luminous Intensity Rank Pb EVERLIGHT HUE: Dom. Wavelength Rank CPN : P N : XXXXXXXXXXXXX RoHS REF: Forward Voltage Rank XXXXXXXXXXXXX CAT : XXX HUE : XXX REF : XXX QTY : XXX LOT NO : XXXXXXXXXX Reference : XXXXXXXX MADE IN TAIWAN Reel Dimensions Carrier Tape Dimensions: Loaded Quantity 500 pcs Per Reel Note: Tolerances unless mentioned ±0.1mm. Unit = mm 7 Copyright © 2010, Everlight Americas All Rights Reserved. Release Date : Apr.30.2014. Issue No: XXXXXXX www.everlightamericas.com DATASHEET SMD  REFLECTOR EAPL4040RA0 Moisture Resistant Packing Process Note: Tolerances unless mentioned ±0.1mm. Unit = mm Reliability Test Items and Conditions The reliability of products shall be satisfied with items listed below. Confidence level：90% LTPD：10% No. Items 1 Reflow Soldering Test Condition Temp. : 260℃±5℃ Min. 5sec. Test Sample Hours/Cycles Size 6 min 22 PCS. 0/1 300 Cycles 22 PCS. 0/1 300 Cycles 22 PCS. 0/1 Ac/Re H : +100℃ 15min 2 Temperature Cycle ∫ 5 min L : -40℃ 15min H : +100℃ 5min 3 Thermal Shock ∫ 10 sec L : -10℃ 5min 4 High Temperature Storage Temp. : 100℃ 1000 Hrs. 22 PCS. 0/1 5 Low Temperature Storage Temp. : -40℃ 1000 Hrs. 22 PCS. 0/1 6 DC Operating Life IF = 20 mA 1000 Hrs. 22 PCS. 0/1 85℃/ 85%RH 1000 Hrs. 22 PCS. 0/1 7 8 High Temperature / High Humidity Copyright © 2010, Everlight Americas All Rights Reserved. Release Date : Apr.30.2014. Issue No: XXXXXXX www.everlightamericas.com DATASHEET SMD  REFLECTOR EAPL4040RA0 Precautions For Use 1. Over-current-proof Customer must apply resistors for protection, otherwise slight voltage shift will cause big current change ( Burn out will happen ). 2. Storage 2.1 Do not open moisture proof bag before the products are ready to use. 2.2 Before opening the package: The LEDs should be kept at 30℃ or less and 90%RH or less. 2.3 After opening the package: The LED's floor life is 48 hours under 30℃ or less and 60% RH or less. If unused LEDs remain, should be stored in moisture proof packages. 2.4 If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded the storage time, baking treatment should be performed using the following conditions. Baking treatment : 60±5℃ for 24 hours. 3. Soldering Condition 3.1 Pb-free solder temperature profile 1~5 °C / Sec. 260°C. Max. 10 Sec. Max. 1~5 °C / Sec. Pre-heating 180~200°C 60 Sec. Max. Above 220°C 120 Sec. Max. 3.2 Reflow soldering should not be done more than two times. 3.3 When soldering, do not put stress on the LEDs during heating. 3.4 After soldering, do not warp the circuit board. 4. Soldering Iron Each terminal is to go to the tip of soldering iron temperature less than 350℃ for 3 seconds within once in less than the soldering iron capacity 25W. Leave two seconds and more intervals, and do soldering of each terminal. Be careful because the damage of the product is often started at the time of the hand solder. 5. Repairing Repair should not be done after the LEDs have been soldered. When repairing is unavoidable, a double-head soldering iron should be used (as below figure). It should be confirmed beforehand whether the characteristics of the LEDs will or will not be damaged by repairing. 9 Copyright © 2010, Everlight Americas All Rights Reserved. Release Date : Apr.30.2014. Issue No: XXXXXXX www.everlightamericas.com