EL0601(TA)

8 PIN SOP HIGH SPEED 10MBit/s LOGIC GATE EL06XX series PHOTOCOUPLER Features: • High speed 10Mbit/s •10kV/μs minimum common mode transient immunity at VCM= 1KV (EL0611) • Guaranteed performance from -40 to 85℃ • Wide operating temperature range of -40°C to 100°C • Logic gate output • High isolation voltage between input and output (Viso=3750 V rms ) • Pb free and RoHS and Halogen free compliant. • cUL approved (No. E214129) • VDE approved (No. 40028116) • SEMKO approved • NEMKO approved • DEMKO approved • FIMKO approved Schematic 1 8 2 7 3 6 4 5 Description The EL0600, EL0601 and EL0611 devices each consists of an infrared emitting diode optically coupled to a high speed integrated photo detector logic gate with a strobable output. The devices are packaged in an 8-pin small outline package which conforms to the standard SO8 footprint. A 0.1μF bypass capacitor must be Applications connected between pins 8 and 5 • Ground loop elimination • LSTTL to TTL, LSTTL or 5 volt CMOS • Line receiver, data transmission • Data multiplexing • Switching power supplies • Pulse transformer replacement • Computer peripheral interface *3 Pin Configuration 1, No Connection 2, Anode 3, Cathode 4. No Connection 5, Gnd 6, Vout Truth Table (Positive Logic) Input Enable Output H H L L H H H L H L L H H NC L L NC H Everlight Electronics Co., Ltd. Document No：DPC-0000088 7, VE 8, VCC 1 Rev.3 http://www.everlight.com August 25, 2011 8 PIN SOP HIGH SPEED 10MBit/s LOGIC GATE EL06XX series PHOTOCOUPLER Absolute Maximum Ratings (Ta=25°C) Parameter Symbol Rating Unit Forward current IF 20 mA Enable input voltage Not exceed VCC by more than 500mV VE 5.5 V Reverse voltage VR 5 V Power dissipation PD 40 mW Power dissipation PC 85 mW Enable input current IE 5 mA Output current IO 50 mA Output voltage VO 7.0 V Supply voltage VCC 7.0 V PO 100 mW VISO 3750 V rms Operating temperature TOPR -40 ~ +100 °C Storage temperature TSTG -55 ~ +125 °C TSOL 260 °C Input Output Output Power Dissipation Isolation voltage *1 Soldering temperature *2 Notes *1 AC for 1 minute, R.H.= 40 ~ 60% R.H. In this test, pins 1 , 2 , 3 & 4 are shorted together, and pins 5 , 6 , 7 & 8 are shorted together. *2 For 10 seconds. Everlight Electronics Co., Ltd. Document No：DPC-0000088 2 Rev.3 http://www.everlight.com August 25, 2011 8 PIN SOP HIGH SPEED 10MBit/s LOGIC GATE EL06XX series PHOTOCOUPLER Electrical Characteristics (Ta=-40 to 85°C unless specified otherwise) Input Parameter Symbol Min. Typ.* Max. Unit Forward voltage VF - 1.4 1.8 V IF = 10mA Reverse voltage VR 5.0 - - V IR = 10μA VF/TA - -1.8 - mV/°C IF =10mA CIN - 60 - pF Symbol Min. Typ.* Max. Unit High level supply current ICCH - - 10 mA IF=10mA, VE=0.5V, VCC=5.5V Low level supply current ICCL - - 13 mA IF=0mA, VE=0.5V, VCC=5.5V High level enable current IEH - - -1.6 mA VE=2.0V, VCC=5.5V Low level enable current IEL - - -1.6 mA VE=0.5V, VCC=5.5V High level enable voltage VEH 2.0 - - V IF=10mA, VCC=5.5V VEL - - 0.8 V IF=10mA, VCC=5.5V Temperature coefficient of forward voltage Input capacitance Condition VF=0, f=1MHz Output Parameter *4 Low level enable voltage Condition Transfer Characteristics (Ta=-40 to 85°C unless specified otherwise) Parameter Symbol Min. Typ.* Max. Unit HIGH Level Output Current IOH - - 100 uA VCC=5.5V, VO=5.5V, IF=250μA, VE=2.0V LOW Level Output Current VOL - - 0.6 V VCC = 5.5V, IF=5mA, VE=2.0V,ICL=13mA Input Threshold Current IFT - - 5 mA VCC= 5.5V, VO=0.6V, VE =2.0V,IOL=13mA Everlight Electronics Co., Ltd. Document No：DPC-0000088 3 Rev.3 Condition http://www.everlight.com August 25, 2011 8 PIN SOP HIGH SPEED 10MBit/s LOGIC GATE EL06XX series PHOTOCOUPLER Switching Characteristics (Ta=-40 to 85°C, VCC=5V, IF=7.5mA unless specified otherwise) Parameter Symbol Min. Typ.* Max. Unit TPHL - 35 75 ns CL = 15pF, RL=350Ω, TA=25°C TPLH - 45 75 ns CL = 15pF, RL=350Ω, TA=25°C |Tphl – Tplh| - 10 35 ns CL = 15pF, RL=350Ω Output rise time *7 (Fig.12) tr - 30 40 ns CL = 15pF, RL=350Ω Output fall time *8 (Fig.12) tf - 10 20 ns CL = 15pF, RL=350Ω Enable Propagation Delay Time to Output High Level *9 (Fig.13) tELH - 30 40 ns Enable Propagation Delay Time to Output Low Level *10 (Fig.13) tEHL - Propagation delay time to *5 output High level (Fig.12) Propagation delay time to *6 output Low level (Fig.12) Pulse width distortion Common Mode Transient Immunity at *11 Logic High Common Mode Transient Immunity at *12 Logic Low 20 30 EL0600 - - - EL0601 5,000 - - CMH V/µS EL0611 10,000 - - EL0611 15,000 - - EL0600 - - - EL0601 5,000 CML V/µS EL0611 10,000 - - EL0611 15,000 - - Everlight Electronics Co., Ltd. Document No：DPC-0000088 4 Rev.3 ns Condition IF = 7.5mA , VEH=3.5V, CL = 15pF, RL=350Ω IF = 7.5mA , VEH=3.5V, CL = 15pF, RL=350Ω IF = 7.5mA , VOH=2.0V, RL=350Ω, TA=25°C VCM=10Vp-p (Fig.14) IF = 7.5mA , VOH=2.0V, RL=350Ω, TA=25°C VCM=50Vp-p (Fig.14) IF = 7.5mA , VOH=2.0V, RL=350Ω, TA=25°C VCM=400Vp-p (Fig.14) IF = 7.5mA , VOH=2.0V, RL=350Ω, TA=25°C VCM=400Vp-p (Fig.15) IF = 0mA , VOL=0.8V, RL=350Ω, TA=25°C VCM=10Vp-p (Fig.14) IF = 0mA , VOL=0.8V, RL=350Ω, TA=25°C VCM=50Vp-p (Fig.14) IF = 0mA , VOL=0.8V, RL=350Ω, TA=25°C VCM=400Vp-p (Fig.14) IF = 7.5mA , VOL=0.8V, RL=350Ω, TA=25°C VCM=400Vp-p (Fig.15) http://www.everlight.com August 25, 2011 8 PIN SOP HIGH SPEED 10MBit/s LOGIC GATE EL06XX series PHOTOCOUPLER Typical Performance Curves Everlight Electronics Co., Ltd. Document No：DPC-0000088 5 Rev.3 http://www.everlight.com August 25, 2011 8 PIN SOP HIGH SPEED 10MBit/s LOGIC GATE EL06XX series PHOTOCOUPLER Everlight Electronics Co., Ltd. Document No：DPC-0000088 6 Rev.3 http://www.everlight.com August 25, 2011 8 PIN SOP HIGH SPEED 10MBit/s LOGIC GATE EL06XX series PHOTOCOUPLER IF=7.5mA IF=3.75mA Input (IF) Ω tPHL tPLH Output (Vo) 1.5V 90% Output (Vo) Ω 10% tf tr Fig. 12 Test circuit and waveforms for tPHL, tPLH, tr, and tf Ω 3.0V Input (VE) 1.5V tEHL tELH Output (Vo) 1.5V Fig. 13 Test circuit and waveform for tEHLand tELH Everlight Electronics Co., Ltd. Document No：DPC-0000088 7 Rev.3 http://www.everlight.com August 25, 2011 8 PIN SOP HIGH SPEED 10MBit/s LOGIC GATE EL06XX series PHOTOCOUPLER Ω Peak VCM 0V 5V CMH Switching Pos. (A), IF=0 Vo VO(Min) VO(Max) Switching Pos. (B), IF=7.5mA VCM CML 0.5V Fig. 14 Test circuit Common mode Transient Immunity μ Ω Fig. 15 Recommended drive circuit for EL0611 families for high-CMR Everlight Electronics Co., Ltd. Document No：DPC-0000088 8 Rev.3 http://www.everlight.com August 25, 2011 8 PIN SOP HIGH SPEED 10MBit/s LOGIC GATE EL06XX series PHOTOCOUPLER Notes: *3 The VCC supply must be bypassed by a 0.1μF capacitor or larger. This can be either a ceramic or solid tantalum capacitor with good high frequency characteristic and should be connected as close as possible to the package VCC and GND pins *4. Enable Input – No pull up resistor required as the device has an internal pull up resistor. *5. tPLH– Propagation delay is measured from the 3.75mA level on the HIGH to LOW transition of the input current pulse to the 1.5 V level on the LOW to HIGH transition of the output voltage pulse. *6. tPHL– Propagation delay is measured from the 3.75mA level on the LOW to HIGH transition of the input current pulse to the 1.5 V level on the HIGH to LOW transition of the output voltage pulse. *7. tr– Rise time is measured from the 90% to the 10% levels on the LOW to HIGH transition of the output pulse. *8. tf– Fall time is measured from the 10% to the 90% levels on the HIGH to LOW transition of the output pulse. *9. tELH– Enable input propagation delay is measured from the 1.5V level on the HIGH to LOW transition of the input voltage pulse to the 1.5V level on the LOW to HIGH transition of the output voltage pulse. *10. tEHL– Enable input propagation delay is measured from the 1.5V level on the LOW to HIGH transition of the input voltage pulse to the 1.5V level on the HIGH to LOW transition of the output voltage pulse. *11 CMH– The maximum tolerable rate of rise of the common mode voltage to ensure the output will remain in the HIGH state (i.e., VOUT > 2.0V). *12 CML– The maximum tolerable rate of rise of the common mode voltage to ensure the output will remain in the LOW output state (i.e., VOUT < 0.8V). Order Information Part Number EL06XX(Z)-V Note X = Part no. ( X = 00, 01 or 11) Z = Tape and reel option (TA, TB or none). V = VDE (optional) Option Description Packing quantity None Standard 100 units per tube -V Standard + VDE 100 units per tube (TA) TA tape & reel option 2000 units per reel (TB) TB tape & reel option 2000 units per reel (TA)-V TA tape & reel option + VDE 2000 units per reel (TB)-V TB tape & reel option + VDE 2000 units per reel Everlight Electronics Co., Ltd. Document No：DPC-0000088 9 Rev.3 http://www.everlight.com August 25, 2011 8 PIN SOP HIGH SPEED 10MBit/s LOGIC GATE EL06XX series PHOTOCOUPLER Package Drawing (Dimensions in mm) Recommended pad layout for surface mount leadform Everlight Electronics Co., Ltd. Document No：DPC-0000088 10 Rev.3 http://www.everlight.com August 25, 2011 8 PIN SOP HIGH SPEED 10MBit/s LOGIC GATE EL06XX series PHOTOCOUPLER Device Marking EL 0600 YWWV Notes 0600 denotes Device Number Y denotes 1 digit Year code WW denotes 2 digit Week code V denotes VDE (optional) Everlight Electronics Co., Ltd. Document No：DPC-0000088 11 Rev.3 http://www.everlight.com August 25, 2011 8 PIN SOP HIGH SPEED 10MBit/s LOGIC GATE EL06XX series PHOTOCOUPLER Tape & Reel Packing Specifications Option TA Option TB Direction of feed from reel Direction of feed from reel Tape dimensions Dimension No. A0 A1 B0 D0 D1 E F Dimension(mm) 6.2±0.1 4.1±0.1 5.28±0.1 1.5±0.1 1.5±0.3 1.75±0.1 5.5±0.1 Dimension No. Po P1 P2 t W K0 K1 Dimension(mm) 4.0±0.1 8.0±0.1 2.0±0.1 0.4±0.1 3.7±0.1 0.3±0.1 Everlight Electronics Co., Ltd. Document No：DPC-0000088 12 Rev.3 12.0+0.3/ -0.1 http://www.everlight.com August 25, 2011 8 PIN SOP HIGH SPEED 10MBit/s LOGIC GATE EL06XX series PHOTOCOUPLER Solder Reflow Temperature Profile 260 C (peak) >255 C (30s Max) 217C 1-3 C/Sec Max 200C 60 – 100 Sec 150C 60 – 120 Sec 1-3 C/Sec Max TIME (S) DISCLAIMER Everlight Electronics Co., Ltd. Document No：DPC-0000088 13 Rev.3 http://www.everlight.com August 25, 2011 8 PIN SOP HIGH SPEED 10MBit/s LOGIC GATE EL06XX series PHOTOCOUPLER 1. Above specification may be changed without notice. EVERLIGHT will reserve authority on material change for above specification. 2. When using this product, please observe the absolute maximum ratings and the instructions for using outlined in these specification sheets. EVERLIGHT assumes no responsibility for any damage resulting from use of the product which does not comply with the absolute maximum ratings and the instructions included in these specification sheets. 3. These specification sheets include materials protected under copyright of EVERLIGHT corporation. Please don’t reproduce or cause anyone to reproduce them without EVERLIGHT’s consent. Everlight Electronics Co., Ltd. Document No：DPC-0000088 14 Rev.3 http://www.everlight.com August 25, 2011