ELEM-5070F4F92838Z15-T4

ELEM-5070F4F92838Z15-T4 Received □ MASS PRODUCTION ■ PRELIMINARY □ CUSTOMER DESIGN DEVICE NO. : DHE-000XXXX PAGE : 13 Revised record 1 REV. DESCRIPTION RELEASE DATE 1 New create 2014.07.25 Copyright © 2014, Everlight All Rights Reserved. Release Date : Jul.25.2014. Issue No: DHE-000XXXX www.everlight.com DATASHEET ELEM-5070F4F92838Z15-T4 ELEM-5070F4F92838Z15-T4 PRELIMINARY Features Small & compact package and with high efficiency luminous flux: 60 lm @ 150mA Typical color temperature: 6000K@150mA optical efficiency@150 mA : 121 lm/W ESD protection up to 8KV Grouping parameter: total luminous flux, color coordinates. RoHS compliant & Pb free. Typical Applications Mobile Phone Camera Flash(Camera flash light /strobe light for mobile devices ) Torch light for DV(Digital Video) application Indoor lighting applications Signal and symbol luminaries for orientation maker lights (e.g. steps, exit ways, etc.) TFT backlighting Exterior and interior illumination applications Decorative and Entertainment Lighting Exterior and interior automotive illumination 2 Copyright © 2014, Everlight All Rights Reserved. Release Date : Jul.25.2014. Issue No: DHE-000XXXX www.everlight.com DATASHEET ELEM-5070F4F92838Z15-T4 Device Selection Guide Chip Emitted Color Materials InGaN White Absolute Maximum Ratings (Tsolder pad =25℃) Parameter Symbol Rating Unit DC Forward Current (mA) IF 250 mA IPulse 500 mA ESD Resistance VB 8000 V Reverse Voltage VR [1] V Junction Temperature TJ 115 ℃ Operating Temperature TOpr -40 ~ +85 ℃ Storage Temperature TStg -40 ~ +100 ℃ Power Dissipation (Pulse Mode) Pd 1.7 W Soldering Temperature TSol 260 ℃ Allowable Reflow Cycles n/a 2 cycles Viewing Angle(2) 2θ1/2 120 deg Peak Pulse Current (mA) (50ms : ON，950ms : OFF) Note: 1. The ELEM series LEDs are not designed for reverse bias used 2. View angle tolerance is ± 5∘ 3. Avoid operating ELEM series LEDs at maximum operating temperature exceed 1 hour. 4. All specification are assured by reliability test for 1000hr, IV degradation less than 30%. 2 5. All reliability items are tested under good thermal management with 1.0x 1.0 cm MCPCB. 6. Peak pulse current shall be applied under conditions as max duration time 50ms and max duty cycle 10%. 7. Operate LED component at maximum rating conditions continuously will cause possible permanent damage and de-rating parameters. Exercise multiple maximum rating parameters simultaneously should not be allowed. When maximum rating parameters are applied over a long period will result potential reliability issue. 3 Copyright © 2014, Everlight All Rights Reserved. Release Date : Jul.25.2014. Issue No: DHE-000XXXX www.everlight.com DATASHEET ELEM-5070F4F92838Z15-T4 Electro-Optical Characteristics (T solder pad =25ºC) Parameter Symbol Min. Typ. Max. Unit Luminous Flux(1) Фv VF 60 3.4 ---3.85 lm Forward Voltage(2) (3) 45 2.85 CCT 5000 ---- 7000 K Symbol Min. Typ. Max. Unit Luminous Flux(1) Фv VF 120 3.6 ---4.15 lm Forward Voltage(2) (3) 90 2.95 CCT 5000 ---- 7000 K Correlated Color Temperature Parameter Correlated Color Temperature V V Condition IF=150mA Condition IF=350mA Note: 1. Luminous flux measurement tolerance: ±10% 2. Forward voltage measurement tolerance: ±0.1V 3. Electric and optical data is tested at 50 ms pulse condition. 4. The data of luminous flux measured at thermal pad=25°C Bin Range of Forward Voltage Binning Bin Code Min. Typ. Max. Unit 2832 3235 3538 2.85 3.25 3.55 ---------- 3.25 3.55 3.85 V Bin Code Min. Typ. Max. Unit F4 F5 F6 F7 F8 F9 45 52 60 70 80 90 ------------------- 52 60 70 80 90 100 lm Condition IF=150mA Bin Range of Luminous Intensity 4 Copyright © 2014, Everlight All Rights Reserved. Release Date : Jul.25.2014. Issue No: DHE-000XXXX Condition IF=150mA www.everlight.com DATASHEET ELEM-5070F4F92838Z15-T4 White Bin Structure 0.42 5000 0.39 5700 5057 y 0.36 7000 5770 0.33 0.30 0.27 0.27 0.30 0.33 0.36 0.39 0.42 x Notes： 1.Color Bin (1) : 5057K 2.Color Bin (2) : 5770K White Bin Coordinate Bin CIE-X CIE-Y CCT Reference Range 5057 0.3300 0.3300 0.3440 0.3524 0.3200 0.3730 0.3420 0.4061 5000K ~ 5700K 5770 0.3030 0.3300 0.3300 0.3110 0.3330 0.3730 0.3200 0.2920 5700K ~ 7000K Note: 1. Color coordinates measurement allowance : ±0.01 2. Color bins are defined at IF=150mA and 50ms pulse operation condition. 5 Copyright © 2014, Everlight All Rights Reserved. Release Date : Jul.25.2014. Issue No: DHE-000XXXX www.everlight.com DATASHEET ELEM-5070F4F92838Z15-T4 Typical Electro-Optical Characteristics Curves Relative Spectral Distribution, IF=150mA@50ms, Tsolder pad=25℃ Relative Intensity(a.u.) 1.0 0.8 0.6 0.4 0.2 0.0 400 500 600 700 800 Wavelength(nm) Typical Radiation Patterns Typical Polar Radiation Pattern for Lambertian X axis Y axis 0.8 Relative Intensity(a.u.) Relativety Luminous intensity 1.0 -15 1.2 0 15 -30 30 1.0 -45 0.6 45 0.8 0.6 0.4 0.4 60 -75 75 0.2 0.2 0.0 0.0 -90 -60 -60 -30 0 2q (Degree) 30 60 90 90 -90 0.2 0.4 0.6 Degree Note: 0.8 1.0 1.2 1. 2θ1/2 is the off axis angle from lamp centerline where the luminous intensity is 1/2 of the peak value. 2. View angle tolerance is ± 5∘. 6 Copyright © 2014, Everlight All Rights Reserved. Release Date : Jul.25.2014. Issue No: DHE-000XXXX www.everlight.com DATASHEET ELEM-5070F4F92838Z15-T4 Forward Voltage vs Forward Current, T solder pad =25ºC Correlated Color Temperature(CCT) vs. Forward Current Corelated Color Temperatrue(K) 6400 6300 6200 6100 6000 5900 5800 0 100 200 300 400 500 Forward Current(mA@50ms) Luminous Flux vs Forward Current, Tsolder pad =25ºC Forward Current Derating Curve,Derating based on TjMAX=115°C at torch mode Forward Current (mA) 500 400 300 200 100 0 0 25 50 75 o Solder temperature ( C) Note: 2 1. All correlation data is tested under superior thermal management with 1.0x 1.0 cm MCPCB 7 Copyright © 2014, Everlight All Rights Reserved. Release Date : Jul.25.2014. Issue No: DHE-000XXXX www.everlight.com 100 DATASHEET ELEM-5070F4F92838Z15-T4 Package Dimension Note: 1. Dimensions are in millimeters. 2. Tolerances unless mentioned are ± 0.1mm. 3. The thermal pad is electrically unity from the Anode and contact pads. 4. Do not handle the device by the lens. Incorrect force applied to the lens may lead to the failure of devices. 8 Copyright © 2014, Everlight All Rights Reserved. Release Date : Jul.25.2014. Issue No: DHE-000XXXX www.everlight.com DATASHEET ELEM-5070F4F92838Z15-T4 Moisture Resistant Packing Materials Label Explanation ‧CPN: Customer Specification (when required) ‧P/N: Everlight Production Number ‧QTY: Packing Quantity ‧CAT: Luminous Flux (Brightness) Bin ‧HUE: Color Bin ‧REF: Forward Voltage Bin ‧LOT No: Lot Number Carrier Tape Dimensions: Loaded Quantity 2000 pcs Per Reel Progress Direction Polarity Note: 1.Dimensions are in millimeters. 2.Tolerances unless mentioned are ±0.1mm. 9 Copyright © 2014, Everlight All Rights Reserved. Release Date : Jul.25.2014. Issue No: DHE-000XXXX www.everlight.com DATASHEET ELEM-5070F4F92838Z15-T4 Reel Dimensions Note: 1. Dimensions are in millimeters. 2. Tolerances for fixed dimensions are ±0.1mm. Moisture Resistant Packing Process 10 Copyright © 2014, Everlight All Rights Reserved. Release Date : Jul.25.2014. Issue No: DHE-000XXXX www.everlight.com DATASHEET ELEM-5070F4F92838Z15-T4 Reflow Soldering Characteristics Soldering and Handling 1. Over-current-proof Customer must apply resistors for protection; otherwise slight voltage shift will cause big current change (Burn out will happen). 2. Storage i. ii. iii. iv. Before the package is opened: The LEDs should be stored at 30°C or less and 50%RH or less after being shipped from Everlight. The storage life is 6 months. If the LEDs are to be stored for more than 6 months, they should be stored in a sealed container with a nitrogen atmosphere and moisture absorbent material. After opening the package: The LED's should be stored under 30℃ or less and 30%RH or less. The LED should be used within 168hrs (7days) after opening the package. If unused LEDs remain, they should be stored in moisture proof packages.After opening the package, the LEDs should be stored at temperature less than 30°C and relative humidity less than 85%. Before using LEDs: The LEDs should be baked under the following conditions: pre-curing at 60±5℃ for 24 hours Do not stack assemblies containing Everlight ELEM LEDs to prevent damage to the optical surface of LEDs. Forces applied to the optical surface may result in the surface being damaged. 3. Soldering Condition i. Soldering Pad ii. Pb-free solder temperature profile 260 C Max. 10sec. Max. Above255 C 30sec.Max. 3 C/sec.Max. 6 C/sec.Max. Pre-heating Above 217 60~150 sec. 150~200 C 60~120sec. iii. iv. v. 11 Reflow soldering should not be done more than two times. When soldering, do not put stress on the LEDs during heating. After soldering, do not warp the circuit board. Copyright © 2014, Everlight All Rights Reserved. Release Date : Jul.25.2014. Issue No: DHE-000XXXX www.everlight.com DATASHEET ELEM-5070F4F92838Z15-T4 4. Soldering Iron Each terminal is to go to the tip of soldering iron temperature less than 350℃ for 3 seconds within once in less than the soldering iron capacity 25W. Leave two seconds and more intervals, and do soldering of each terminal. Be careful because the damage of the product is often started at the time of the hand solder. 5. Repairing Repair should not be done after the LEDs have been soldered. When repairing is unavoidable, a double-head soldering iron should be used (as below figure). It should be confirmed beforehand whether the characteristics of the LEDs will or will not be damaged by repairing. 12 Copyright © 2014, Everlight All Rights Reserved. Release Date : Jul.25.2014. Issue No: DHE-000XXXX www.everlight.com