HIR19-21C_05

Technical Data Sheet 0.8mm Height Flat Top Infrared LED HIR19-21C/L11/TR8 Features ․High reliability ․Small double-end package ․Peak wavelength λp=850nm ․Package in 8mm tape on 7” diameter reel ․Low forward voltage ․Pb free ․The product itself will remain within RoHS compliant version. Descriptions ․HIR19-21C/L11/TR8 is an infrared emitting diode in miniature SMD package which is molded in a water clear plastic with flat top view lens. ․The device is spectrally matched with silicon photodiode and phototransistor. Applications ․PCB mounted infrared sensor ․Infrared remote control units with high power requirement ․Smoke detector ․Infrared applied system Device Selection Guide LED Part No. HIR Chip Material GaAlAs Lens Color Water clear Everlight Electronics Co., Ltd. Device No：DTH-019-001 http:\\www.everlight.com Prepared date：07-20-2005 Rev 2 Page: 1 of 10 Prepared by：Jaine Tsai HIR19-21C/L11/TR8 Package Dimensions 1 2 1 2 1 Cathode 2 Anode Notes: 1.All dimensions are in millimeters 2.Tolerances unless dimensions ±0.1mm Absolute Maximum Ratings (Ta=25℃) Parameter Continuous Forward Current Peak Forward Current Reverse Voltage Operating Temperature Storage Temperature Soldering Temperature Power Dissipation at(or below) 25℃Free Air Temperature Symbol IF IFP VR Topr Tstg Tsol Pd Rating 65 1.0 5 -25 ~ +85 -40 ~ +85 260 130 Units mA A V ℃ ℃ ℃ mW Notes: *1:IFP Conditions--Pulse Width≦100μs and Duty≦1%. *2:Soldering time≦5 seconds. Everlight Electronics Co., Ltd. Device No：DTH-019-001 http:\\www.everlight.com Prepared date：07-20-2005 Rev 2 Page: 2 of 10 Prepared by：Jaine Tsai HIR19-21C/L11/TR8 Electro-Optical Characteristics (Ta=25℃) Parameter Radiant Intensity Peak Wavelength Spectral Bandwidth Forward Voltage Reverse Current View Angle Symbol Ee λp Δλ Condition IF=20mA . IF=100mA Pulse Width≦100μs ,Duty≦1% Min. 0.2 -------- Typ. 0.8 4.2 850 45 1.45 1.80 -145 Max. ----1.65 2.40 10 -- Units mW /sr nm nm IF=20mA IF=50mA IF=20mA VF IR 2θ1/2 . IF=100mA Pulse Width≦100μs ,Duty≦1% V μA deg VR=5V IF=20mA Everlight Electronics Co., Ltd. Device No：DTH-019-001 http:\\www.everlight.com Prepared date：07-20-2005 Rev 2 Page: 3 of 10 Prepared by：Jaine Tsai HIR19-21C/L11/TR8 Typical Electro-Optical Characteristics Curves Fig.1 Forward Current vs. Ambient Temperature Fig.2 Spectral Distribution 140 120 100 80 60 40 20 0 100 80 60 40 20 0 IF=20mA Ta=25° C -25 0 20 40 60 80 100 790 810 830 850 870 890 910 930 950 Fig.3 Peak Emission Wavelength Ambient Temperature 900 Fig.4 Forward Current vs. Forward Voltage 4 10 875 3 10 850 2 10 825 1 10 800 -25 0 25 50 75 100 0 1 2 3 4 5 6 7 8 Everlight Electronics Co., Ltd. Device No：DTH-019-001 http:\\www.everlight.com Prepared date：07-20-2005 Rev 2 Page: 4 of 10 Prepared by：Jaine Tsai HIR19-21C/L11/TR8 Typical Electro-Optical Characteristics Curves Fig.5 Relative Intensity vs. Forward Current Fig.6 Relative Radiant Intensity vs. Angular Displacement 100 Ie-Radiant Intensity(mW/sr) -20 -10 0 10 20 30 10 1.0 0.9 40 50 60 70 80 0.6 0.4 0.2 0 0.2 0.4 0.6 1 0.8 0.7 0 1 2 3 0 10 10 10 10 10 4 IF-Forward Current (mA) Fig.7 Relative Intensity vs. Ambient Temperature(°C) Fig.8 Forward Voltage vs. Ambient Temperature(°C) 1.0 1.6 0.8 IF=20mA 1.4 IF=20mA 0.6 1.2 0.4 25 50 75 100 120 1 25 50 75 100 120 Everlight Electronics Co., Ltd. Device No：DTH-019-001 http:\\www.everlight.com Prepared date：07-20-2005 Rev 2 Page: 5 of 10 Prepared by：Jaine Tsai HIR19-21C/L11/TR8 Precautions For Use 1. Over-current-proof Customer must apply resistors for protection , otherwise slight voltage shift will cause big current change ( Burn out will happen ). 2. Storage 2.1 Do not open moisture proof bag before the products are ready to use. 2.2 Before opening the package, the LEDs should be kept at 30℃ or less and 90%RH or less. 2.3 The LEDs should be used within a year. 2.4 After opening the package, the LEDs should be kept at 30℃ or less and 70%RH or less. 2.5 The LEDs should be used within 168 hours (7 days) after opening the package. 2.6 If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded the storage time, baking treatment should be performed using the following conditions. Baking treatment : 60±5℃ for 24 hours. 3. Soldering Condition 3.1 Pb-free solder temperature profile 3.2 Reflow soldering should not be done more than two times. 3.3 When soldering, do not put stress on the LEDs during heating. 3.4 After soldering, do not warp the circuit board. Everlight Electronics Co., Ltd. Device No：DTH-019-001 http:\\www.everlight.com Prepared date：07-20-2005 Rev 2 Page: 6 of 10 Prepared by：Jaine Tsai HIR19-21C/L11/TR8 4.Soldering Iron Each terminal is to go to the tip of soldering iron temperature less than 280℃ for 3 seconds within once in less than the soldering iron capacity 25W. Leave two seconds and more intervals, and do soldering of each terminal. Be careful because the damage of the product is often started at the time of the hand solder. 5.Repairing Repair should not be done after the LEDs have been soldered. When repairing is unavoidable, a double-head soldering iron should be used (as below figure). It should be confirmed beforehand whether the characteristics of the LEDs will or will not be damaged by repairing. Everlight Electronics Co., Ltd. Device No：DTH-019-001 http:\\www.everlight.com Prepared date：07-20-2005 Rev 2 Page: 7 of 10 Prepared by：Jaine Tsai HIR19-21C/L11 Reliability Test Item And Condition The reliability of products shall be satisfied with items listed below. Confidence level：90% LTPD：10% NO. Item Test Conditions Test Hours/ Sample Cycles Sizes 22pcs 22pcs IR≧U×2 Ee≦L×0.8 VF≧U×1.2 U：Upper Specification Limit L：Lower Specification Limit Failure Judgement Criteria Ac/Re 1 REFLOW Soldering TEMP.：260℃±5℃ 6Mins 5secs 15mins 50Cycles 2 Temperature Cycle H : +100℃ 5mins L : -40℃ 15mins 3 Thermal Shock H :+100℃ L :-10℃ 4 High Temperature Storage 5 Low Temperature Storage 5mins 50Cycles 10secs 5mins 1000hrs 1000hrs 1000hrs 1000hrs 0/1 0/1 22pcs 0/1 TEMP.：+100℃ TEMP.：-40℃ 22pcs 22pcs 22pcs 22pcs 0/1 0/1 0/1 0/1 6 DC Operating Life IF=20mA 7 High Temperature/ 85℃ / 85% R.H High Humidity Everlight Electronics Co., Ltd. Device No：DTH-019-001 http:\\www.everlight.com Prepared date：07-20-2005 Rev 2 Page: 8 of 10 Prepared by：Jaine Tsai HIR19-21C/L11/TR8 Package Dimensions Taping Dimensions 1 2 1 Cathode 2 Anode Unit:mm Everlight Electronics Co., Ltd. Device No：DTH-019-001 http:\\www.everlight.com Prepared date：07-20-2005 Rev 2 Page: 9 of 10 Prepared by：Jaine Tsai HIR19-21C/L11/TR8 Packing Quantity Specification 1.3000Pcs/1Volume，1Volume/1Bag 2.10Boxes/1Carton Label Form Specification CPN: Customer’s Production Number P/N : Production Number QTY: Packing Quantity CAT: Ranks HUE: Peak Wavelength REF: Reference LOT No: Lot Number MADE IN TAIWAN: Production Place RoHS HIR19-21C/L11/TR8 Notes 1. Above specification may be changed without notice. EVERLIGHT will reserve authority on material change for above specification. 2. When using this product, please observe the absolute maximum ratings and the instructions for using outlined in these specification sheets. EVERLIGHT assumes no responsibility for any damage resulting from use of the product which does not comply with the absolute maximum ratings and the instructions included in these specification sheets. 3. These specification sheets include materials protected under copyright of EVERLIGHT corporation. Please don’t reproduce or cause anyone to reproduce them without EVERLIGHT’s consent. EVERLIGHT ELECTRONICS CO., LTD. Office: No 25, Lane 76, Sec 3, Chung Yang Rd, Tucheng, Taipei 236, Taiwan, R.O.C Tel: 886-2-2267-2000, 2267-9936 Fax: 886-2267-6244, 2267-6189, 2267-6306 http:\\www.everlight.com Everlight Electronics Co., Ltd. Device No：DTH-019-001 http:\\www.everlight.com Prepared date：07-20-2005 Rev 2 Page: 10 of 10 Prepared by：Jaine Tsai