IR26-61C/L110/TR8

Technical Data Sheet 1.6mm round Subminiature Side Looking Infrared LED IR26-61C/L110/TR8 Features ․Small double-end package ․Low forward voltage ․Good spectral matching to Si photo detector ․Package in 8mm tape on 7〞diameter reel. ․Pb free ․The product itself will remain within RoHS compliant version. Descriptions ․IR26-61C/L110/TR8 is an infrared emitting diode in miniature SMD package which is molded in a water clear plastic with spherical top view lens. The device is spectrally matched with silicon photodiode and phototransistor Applications ․Infrared applied system Device Selection Guide LED Part No. IR26-61C/L110/TR8 Chip Material GaAlAs Lens Color Water Clear Everlight Electronics Co., Ltd. http://www.everlight.com Rev 1 Device No Prepared date Prepared by Jason Ho ：DIR-0000829 ：02-17-2011 Page: 1 of 9 ： IR26-61C/L110/TR8 Package Dimensions Recommended Soldering Pattern for Side Looker Notes: 1.All dimensions are in millimeters 2.Tolerances unless dimensions ±0.1mm Absolute Maximum Ratings (Ta=25℃ ℃) Parameter Symbol Rating Continuous Forward Current IF 65 Units mA Reverse Voltage VR 5 V Operating Temperature Topr -40 ~ +85 ℃ Storage Temperature Tstg -40 ~ +100 ℃ Tsol 260 ℃ Pd 100 mW Soldering Temperature *1 Power Dissipation at(or below) 25℃Free Air Temperature Notes: *1:Soldering time≦5 seconds. Everlight Electronics Co., Ltd. http://www.everlight.com Rev 1 Device No Prepared date Prepared by Jason Ho ：DIR-0000829 ：02-17-2011 Page: 2 of 9 ： IR26-61C/L110/TR8 Electro-Optical Characteristics (Ta=25℃ ℃) Parameter Symbol Ie Radiant Intensity Condition IF=20mA IF=100mA ≦100μs ,Duty≦1% Pulse Width Min. Typ. Max. 1.0 3.0 -- -- 14 -- 940 50 960 nm nm 1.2 -1.5 Peak Wavelength λp IF=20mA 920 Spectral Bandwidth Δλ IF=20mA IF=20mA -- IF=100mA ≦100μs ,Duty≦1% -- 1.5 1.8 Forward Voltage VF Pulse Width Units mW/sr V Reverse Current IR VR=5V -- -- 10 μA Optical Rise Time tr IF=20mA -- 700 -- ns Optical Fall Time tf 2θ1/2 IF=20mA --- 400 -- 25 -- ns deg View Angle IF=20mA Everlight Electronics Co., Ltd. http://www.everlight.com Rev 1 Device No Prepared date Prepared by Jason Ho ：DIR-0000829 ：02-17-2011 Page: 3 of 9 ： IR26-61C/L110/TR8 Typical Electro-Optical Characteristics Curves IF - Forward Current (mA) Fig.1 Forward Current vs. Ambient Temperature Fig.2 Spectral Distribution 100 100 80 80 60 60 40 40 20 20 IF=20mA Ta=25° C 0 0 0 20 40 60 80 Tamb - Ambient Temperature (°C) 100 Fig.3 Relative Intensity vs. Forward Current Fig.4 Forward Current vs. Forward Voltage 4 10 15 Forward Current(mA) R a d ia n t In te n s ity (m W /s r) 12 9 6 tp=100us tp/T=1/100 3 10 2 10 3 1 0 10 0 5 10 15 20 25 30 35 40 45 50 55 60 65 0 1 2 3 4 Forward Voltage(V) Forward Current(mA) Everlight Electronics Co., Ltd. http://www.everlight.com Rev 1 Device No Prepared date Prepared by Jason Ho ：DIR-0000829 ：02-17-2011 Page: 4 of 9 ： 5 IR26-61C/L110/TR8 Typical Electro-Optical Characteristics Curves Fig.6 Relative Radiant Intensity vs. Angular Displacement 0 1.0 30 R e le tiv e R a d ia n t In te n s ity 0.8 0.6 60 0.4 0.2 0.0 -90 90 -60 -30 0 View Angle(Degree) Everlight Electronics Co., Ltd. http://www.everlight.com Rev 1 Device No Prepared date Prepared by Jason Ho ：DIR-0000829 ：02-17-2011 Page: 5 of 9 ： IR26-61C/L110/TR8 Precautions For Use 1. Over-current-proof Customer must apply resistors for protection , otherwise slight voltage shift will cause big current change ( Burn out will happen ). 2. Storage 2.1 Do not open moisture proof bag before the products are ready to use. 2.2 Before opening the package, the LEDs should be kept at 30℃ or less and 90%RH or less. 2.3 The LEDs should be used within a year. 2.4 After opening the package, the LEDs should be kept at 30℃ or less and 70%RH or less. 2.5 The LEDs should be used within 168 hours (7 days) after opening the package. 2.6 If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded the storage time, baking treatment should be performed using the following conditions. Baking treatment : 60±5℃ for 24 hours. 3. Soldering Condition 3.1 Pb-free solder temperature profile 3.2 Reflow soldering should not be done more than two times. 3.3 When soldering, do not put stress on the LEDs during heating. 3.4 After soldering, do not warp the circuit board. Everlight Electronics Co., Ltd. http://www.everlight.com Rev 1 Device No Prepared date Prepared by Jason Ho ：DIR-0000829 ：02-17-2011 Page: 6 of 9 ： IR26-61C/L110/TR8 4.Soldering Iron Each terminal is to go to the tip of soldering iron temperature less than 350℃ for 3 seconds within once in less than the soldering iron capacity 25W. Leave two seconds and more intervals, and do soldering of each terminal. Be careful because the damage of the product is often started at the time of the hand solder. 5.Repairing Repair should not be done after the LEDs have been soldered. When repairing is unavoidable, a double-head soldering iron should be used (as below figure). It should be confirmed beforehand whether the characteristics of the LEDs will or will not be damaged by repairing. Everlight Electronics Co., Ltd. http://www.everlight.com Rev 1 Device No Prepared date Prepared by Jason Ho ：DIR-0000829 ：02-17-2011 Page: 7 of 9 ： IR26-61C/L110/TR8 Package Dimensions 1. Reel Dimensions Note: The tolerances unless mentioned is ±0.1mm ,Unit = mm 2. Carrier Tape Dimensions:(Quantity: 1500pcs/reel) Note: The tolerances unless mentioned is ±0.1mm ,Unit = mm Everlight Electronics Co., Ltd. http://www.everlight.com Rev 1 Device No Prepared date Prepared by Jason Ho ：DIR-0000829 ：02-17-2011 Page: 8 of 9 ： IR26-61C/L110/TR8 Packing Procedure Aluminum moistue-proof bag Label Desiccant Label Label Form Specification Pb CPN: Customer’s Production Number EVERLIGHT P/N : Production Number CPN : P N RoHS QTY: Packing Quantity CAT: Ranks CAT : HUE : REF : QTY :1500 HUE: Peak Wavelength REF: Reference LOT NO : LOT No: Lot Number Reference : MADE IN TAIWAN: Production Place MADE IN TAIWAN Notes 1. Above specification may be changed without notice. EVERLIGHT will reserve authority on material change for above specification. 2. When using this product, please observe the absolute maximum ratings and the instructions for using outlined in these specification sheets. EVERLIGHT assumes no responsibility for any damage resulting from use of the product which does not comply with the absolute maximum ratings and the instructions included in these specification sheets. 3. These specification sheets include materials protected under copyright of EVERLIGHT corporation. Please don’t reproduce or cause anyone to reproduce them without EVERLIGHT’s consent. EVERLIGHT ELECTRONICS CO., LTD. Office: No 6-8, Zhonghua Rd., Shulin Dist., New Taipei City 23860, Taiwan, R.O.C Tel: 886-2-2685-6688 Fax: 886-2-2685-6699 http://www.everlight.com Everlight Electronics Co., Ltd. http://www.everlight.com Rev 1 Device No Prepared date Prepared by Jason Ho ：DIR-0000829 ：02-17-2011 Page: 9 of 9 ：