IR67-21C/L261/S65/TR8(GDB)

Technical Data Sheet Top Infrared LED IR67-21C/L261/S65/TR8 Features ․Compatible with infrared and vapor phase reflow solder process. ․Low forward voltage. ․View angle 120° ․Pb free ․The product itself will remain within RoHS compliant version. Description ․IR67-21C/L261/S65/TR8 is an infrared emitting diode in miniature SMD package which is molded in a water clear plastic with flat top view lens. ․The device is spectrally matched with silicon photodiode and phototransistor. Applications ․Sensor ․Optoelectronic switch ․Camera ․VCR ․Video ․Smoke detector Device Selection Guide 1 Device No. Chip Material Lens Color IR67-21C/L261/S65/TR8 GaAlAs Water Clear Copyright © 2010, Everlight All Rights Reserved. Release Date : May.18.2015. Issue No: DIR-0000885 Rev 2 www.everlight.com DATASHEET IR67-21C/L261/S65/TR8 Package Dimensions Notes: 1.All dimensions are in millimeters 2.Tolerances unless dimensions ±0.1mm Absolute Maximum Ratings (Ta=25℃) Parameter Continuous Forward Current Peak Forward Current *1 Surge Forward Current *2 Reverse Voltage Operating Temperature Storage Temperature Soldering Temperature *3 Power Dissipation at(or below) 25℃Free Air Temperature Temperature resistance junction ambient Symbol Rating Unit IF IFP IFS VR Topr Tstg Tsol 65 1 2 5 -40~ +85 -40 ~ +100 260 mA A A V ℃ ℃ ℃ Pd 130 mW Rthj-a 400 ℃/W Notes: *1:IFP Conditions--Pulse Width≦100μ s and Duty≦1%. *2:IFS Conditions--Pulse Width≦100μ s *3:Soldering time≦5 seconds. 2 Copyright © 2010, Everlight All Rights Reserved. Release Date : May.18.2015. Issue No: DIR-0000885 Rev 2 www.everlight.com DATASHEET IR67-21C/L261/S65/TR8 Electro-Optical Characteristics (Ta=25℃) Parameter Symbol Condition IF=20mA Min. 1.0 Typ. 2.0 Max. 3.5 Radiant Intensity IE IF=100mA 4.0 8.0 -- Pulse Width≦100μ s ,Duty≦1% Total Radiated Power Peak Wavelength Spectral Bandwidth Forward Voltage Po λ p Δλ IF=100mA IF=20mA IF=20mA ---- 20 940 50 ---- -- 1.20 1.60 VF IF=20mA IF=100mA -- 1.45 1.80 Pulse Width≦100μ s ,Duty≦1% Unit mW /sr mW nm nm V Reverse Current IR VR=5V -- -- 10 μ A View Angle 2θ 1/2 IF=20mA -- 120 -- deg Active chip area A ---- 0.122 mm2 Dimensions of the active chip area L×W ---- 0.350*0.350 mm×mm Rank Condition：IF=20mA Unit：mW/sr Bin Number Min Max 3 G 1.0 2.5 H 2.0 3.5 Copyright © 2010, Everlight All Rights Reserved. Release Date : May.18.2015. Issue No: DIR-0000885 Rev 2 www.everlight.com DATASHEET IR67-21C/L261/S65/TR8 Typical Electrical/Optical/Characteristics Curves for IR Forward Currnt vs. Ambient Temperature 140 Spectral Distribution 1.0 120 0.8 Relative Radinat Intensity (%) 100 80 60 40 20 0 -40 -20 0 20 40 60 80 0.6 0.4 0.2 100 0.0 700 725 750 775 800 825 850 875 900 925 950 975 1000 1025 1050 Wavelength (nm) Forward Current vs. Forward Voltage Radiant Intensity vs. Forward Current 4 10 8 tp=100us tp/T=1/100 Radiant Intensity(mW/sr) Forward Current(mA) 10 3 10 2 10 4 2 0 1 10 0 1 2 3 Forward Voltage(V) 4 6 4 5 0 5 10 15 20 25 30 35 40 45 50 55 60 65 Forward Current(mA) Copyright © 2010, Everlight All Rights Reserved. Release Date : May.18.2015. Issue No: DIR-0000885 Rev 2 www.everlight.com DATASHEET IR67-21C/L261/S65/TR8 Relative Radiant Intensity vs. Angular Displacement 0 1.0 20 30 0.9 40 0.8 50 0.7 Relative Radiant Intensity 10 0.6 60 0.5 0.4 70 0.3 0.2 80 0.1 0.0 -90 -80 -70 -60 -50 -40 -30 -20 -10 0 90 Angle(Degree) 5 Copyright © 2010, Everlight All Rights Reserved. Release Date : May.18.2015. Issue No: DIR-0000885 Rev 2 www.everlight.com DATASHEET IR67-21C/L261/S65/TR8  Precautions For Use 1. Over-current-proof Customer must apply resistors for protection , otherwise slight voltage shift will cause big current change ( Burn out will happen ). 2. Storage 2.1 Do not open moisture proof bag before the products are ready to use. 2.2 Before opening the package, the LEDs should be kept at 30℃ or less and 90%RH or less. 2.3 The LEDs should be used within a year. 2.4 After opening the package, the LEDs should be kept at 30℃ or less and 70%RH or less. 2.5 The LEDs should be used within 168 hours (7 days) after opening the package. 2.6 If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded the storage time, baking treatment should be performed using the following conditions. Baking treatment : 60±5℃ for 24 hours. 3. Soldering Condition 3.1 Pb-free solder temperature profile 3.2 Reflow soldering should not be done more than two times. 3.3 When soldering, do not put stress on the LEDs during heating. 3.4 After soldering, do not warp the circuit board. 6 Copyright © 2010, Everlight All Rights Reserved. Release Date : May.18.2015. Issue No: DIR-0000885 Rev 2 www.everlight.com DATASHEET IR67-21C/L261/S65/TR8 4. Soldering Iron Each terminal is to go to the tip of soldering iron temperature less than 350℃ for 3 seconds within once in less than the soldering iron capacity 25W. Leave two seconds and more intervals, and do soldering of each terminal. Be careful because the damage of the product is often started at the time of the hand solder. 5. Repairing Repair should not be done after the LEDs have been soldered. When repairing is unavoidable, a double-head soldering iron should be used (as below figure). It should be confirmed beforehand whether the characteristics of the LEDs will or will not be damaged by repairing. 7 Copyright © 2010, Everlight All Rights Reserved. Release Date : May.18.2015. Issue No: DIR-0000885 Rev 2 www.everlight.com DATASHEET IR67-21C/L261/S65/TR8 Package Dimensions Note: The tolerances unless mentioned is ±0.1mm ,Unit = mm 2. Carrier Tape Dimensions:(Quantity: 8000pcs/reel) Note: The tolerances unless dimension is ±0.1mm ,Unit = mm 8 Copyright © 2010, Everlight All Rights Reserved. Release Date : May.18.2015. Issue No: DIR-0000885 Rev 2 www.everlight.com DATASHEET IR67-21C/L261/S65/TR8 Packing Procedure Aluminum moistue-proof bag Label Desiccant Label Label Form Specification Pb CPN: Customer’s Production Number P/N : Production Number EVERLIGHT CPN : P N : XXXXXXXXXXXXX RoHS XXXXXXXXXXXXX QTY : XXX LOT NO : XXXXXXXXXX Reference : XXXXXXXX CAT : XXX HUE : XXX REF : XXX QTY: Packing Quantity CAT: Ranks HUE: Peak Wavelength REF: Reference LOT No: Lot Number MADE IN TAIWAN: Production Place Notes 1. Above specification may be changed without notice. EVERLIGHT will reserve authority on material change for above specification. 2. When using this product, please observe the absolute maximum ratings and the instructions for using outlined in these specification sheets. EVERLIGHT assumes no responsibility for any damage resulting from use of the product which does not comply with the absolute maximum ratings and the instructions included in these specification sheets. 3. These specification sheets include materials protected under copyright of EVERLIGHT corporation. Please don’t reproduce or cause anyone to reproduce them without EVERLIGHT’s consent. 9 Copyright © 2010, Everlight All Rights Reserved. Release Date : May.18.2015. Issue No: DIR-0000885 Rev 2 www.everlight.com